Search Documents

By H. S. Munroe

To those familiar with ore-dressing practice, it is hardly necessary to dwell upon the importance of the jig. Within its proper sphere no substitute has been found that does the work as well or as cheaply. Its capacity is large, it requires but little attention, and the losses are small. In one form or another, it is the principal machine used in the concentration of low-grade ores, and for the separation of one metallic mineral from another; and it is almost the only machine used for the purification of coal. The present paper is a study of the action of the jig in the light of results obtained in the Lake Superior copper mills, ad at the St. Joseph Lead Co.'s dressing-works, in Missouri; and a description of experiments undertaken with the view of reproducing and isolating the conditions of jigging, in order to develop the laws which underlie the process. There are two recognized systems of jigging, the English and the Continental or German. The English system is a development of the hand-jigging formerly employed in Cornwall and other metalliferous districts of England, and introduced by English miners to this country. In this method the crushed ore, coarse and fine together, is first jigged oh a

Jan 1, 1889

THE paper on "Specific Efficiency of the Blast Furnace" by Richard Franchot, which was pub-lished in the September issue of MINING AND METALLURGY, was presented for discussion at the Pitts-burgh meeting. The session opened with a discussion among S. P. Kinney, Mr. Franchot, and J. N. Reese as to the methods and results in sampling for cyanides in the blast furnace. This is covered in detail in writ-ten discussion below. T. T. Read objected to the use of the term specific efficiency as likely to be confusing. The blast furnace has to perform the function of reducing Fe, 03 to Fe as well as that of fusing the metal and, since the reduc-tion of Fe, 0? involves a CO equilibrium, it seems mis-leading to calculate efficiency on the basis of burning the , all carbon to CO? since it is not possible. Mr. Franchot replied that he used the term in the sense defined by Richards in his "Metallurgical Calculations;" but a subsequent search failed to reveal the term in Richards, who says (page 245, 1st edition): The practical conclusion is that a blast furnace generates in itself not much over 40 per cent of the calorific power of the fuel used, and rejects nearly 60 per cent; by using part of the waste gases to heat the blast, however, some of this rejected heat, to an amount representing net 5 to 10 per cent of the calorific power of the fuel used, is returned to and injected bodily into the furnace, thus rendering available for the purpose of running the furnace about 50 per cent of the calorific power of the fuel as a maximum. The efficiency with which the furnace applies this 50 per cent usefully to the objects of the reducing and smelting is another question for investigation.

Jan 2, 1927

By C. C. Harris

The characteristics of some common size distribution equations are critically discussed. A generalized form of several well-known size distribution equations is obtained from a differential equation describing statistical distributions. The equation contains three parameters and can describe the major features of size distributions in the fine and the coarse size regions. A graphical method for its implementation is provided. The application of this and other equations to sets of data are compared both for the quality of fit and from a comminution kinetics viewpoint. If a narrow size range of a brittle material is broken sufficiently to obliterate the feed sizes, but not so severely that excessive secondary breakage occurs, a plot of cumulative fraction by weight undersize (Y) vs. sieve size (X) on a log log grid (sometimes called the Gates-Gaudin-Schuhmann plot)1-3 gives a straight line of slope ~ 1 over much of its range. On closer inspection, deviations in the extreme coarse range covering perhaps 10 to 30% of the total sample may be apparent (frequently, a change in slope from ~ 1 to a value different from unity) together with over-all slight irregular departures from a smooth line. One model of breakage postulates that the same fracture pattern persists throughout all size ranges.4 The fracture pattern is characterized by the slope of the line on a log log grid. Accordingly, a distribution of sizes broken in the manner specified earlier is expected to produce a size distribution having the same slope as that of a broken narrow size range. Additionally, the slight irregularities mentioned above should even out in the summation process, giving a smooth straight line of slope ~1 on a log log plot. This idealized state of affairs does not, however, describe the distribution of a multi-event process such as that for a tumbling mill product. On the average, these curves (plotted again log log) tend to have a slope in the fine region different from and usually less than unity,5 while the coarse size region curves with increasing slope for cases of mild reduction, and with decreasing slope when moderate or severe size reduction has occurred. In addition, there are usually slight irregular deviations from a smooth curve. Most curves display two distinct regions — fine and coarse — and a few curves show one or more intermediate regions. Feed size studies6,7 show an effect which theory is required to explain. For the same material, mill loading and other operating conditions, and the same time of grinding, plotting the dimensionless ratios Y vs. X/(feed size) does not reduce the size distribution data to the same curve. Y vs. X does not correlate the coarse region, but it can provide a crude correlation of the fine region which improves as size diminishes and as grinding time increases. The size distribution in the coarse region is somewhat more dependent on the feed size than is the distribution in the fine region wherein the degree of dependence diminishes as time proceeds; the distribution of sizes in the fine region are determined largely by the nature of the material and the comminution conditions. A comprehensive model of comminution must recognize that several different patterns or modes of breakage can occur in a mill; 5,8,9 that there can be some selection in that some size ranges are broken more than others; and that, while some particles may be the product of a single fracture event, or may even remain unbroken, others result from multiple rebreak-age. Thus, breakage in a tumbling mill is more complex than the Schuhmann4 model admits in that several different types of comminution micro-events* occur rather than just one type, and these events, though different in size scale, are of the same overall pattern as that which is visualized by the model. The concept of an average comminution micro-event has, therefore, a mathematical rather than a physical connotation, at least for tumbling milling. Equations with which to describe particle size distributions have been sought for over half a century.10-13 No equation presently in general use was first derived from an analysis of the statistical mechanics of breakage; whatever theoretical basis the existing

Jan 1, 1969

By Oliver C. Ralston, Foster Fraas

INTRODUCTION ELECTROSTATIC methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to beneficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollastonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. THE SEPARATOR The separator used in these tests is of the nonhomogeneous field type shown in Fig I[a]. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll." [ ]

Jan 1, 1947

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

Following the suggestion of Engineering Council and at the direction of, the President, representatives from each of the Federal Government bureaus interested in map-making were called into a conference for the purpose of coordinating all of the Government's map-making activities. This conference has now reported back to the President the results of its findings, which indicate that Engineering Council's recommendation in this matter was well founded. While the conference report states that its members were of the opinion that little duplication of effort existed, it recommends the formation of a permanent Board of Surveys and Maps. An extended review of the map-making activities, which is given as an appendix to the report, indicates that this recommendation is a logical step. The conference recommendations concerning this Board of Surveys and Maps are as follows: (1) the Board is to he com-posed of representatives of mapping bureaus to be assisted by outside engineering organizations, which have been named above; (2) the estab-lishment of an information office in one of the Government bureaus, preferably the Geological Survey, which is to be under the supervision of the Board and is to be a mapping information clearing house for the Government and outside engineering organizations; (3) copyright laws are to be so changed that copies of all. maps made in the United States and with Governmental authority, will go to the central information office; (4) the Government departments are to receive orders to cooperate, with the Board; (5) future topographic maps of all kinds are to conform with specifications for the standard topographic map; (6) the U. S. Coast and Geodetic Survey to have supervision of final adjustment of all important control data under specifications approved by Board of Surveys and Maps; (7) surveys in the form of maps and publications are to be issued as soon as possible after field work has been completed; (8) program of the Interdepartmental Committee on Aerial Surveying was approved. Outside technical and scientific organizations that are called in for consultation are to operate in an advisory capacity only, responsibility for action on Governmental work is. to rest solely with the Governmental agencies.

Jan 12, 1919

By M. M. Rao, P. G. Winchell

The growth rates of bainitic plates were measured at 400°C in Fe-Ni-C alloys containing 0.10 atom-fract~on nickel and 0.0012 to 0.0075 atonz-fraction carbon. The growth rates are adequately represented by where xc is nearly the atom fraction carbon of the bulk austenite and PXCy is nearly the carbon atom fractlon in the ferrlte of radiids p In equilibrium with austetzite. The form of the equation is that predicted by a model in which carbon diffusion in austernite controls the gvowth, but the numerical constatnt is two orders of magnitude below that suggested by the model. THE growth of bainitic plates in steel is often assumed to be controlled by the diffusion of carbon away from the advancing plate tip. This hypothesis predicts that the growth rate will increase as the carbon content of the austenite, xCz, is reduced toward the carbon content of the saturated ferrite comprising the plate tip, PxCY The growth rate should vary approximately as (xCg- pxCy)-1. Experimental observation of the growth behavior at low carbon levels should provide a significant test of this model. An alloying element in addition to carbon is required so that low-carbon austenite can be experimentally observed while undergoing bainitic transformation. Nickel was selected. The presence of nickel complicates the interpretation of the data in two ways: First, diffusion of nickel during the transformation would make analysis very difficult. Nickel is assumed immobile during the transformation. Second, nickel affects the solubility of carbon in ferrite and austenite in equilibrium. This effect has been evaluated.' At the completion of our experimental work Goode-now et al.2 published data in essential agreement with the observations to be reported here. Since their discussion is abbreviated and their data are scanty in the region of interest, we believe the present work is of significance. I) THE MODEL OF BAINITIC PLATE GROWTH The rate of lengthening of a plate is assumed to be controlled by the diffusion of carbon from the advancing ferrite-austenite interface into the surrounding austenite. The precipitation of carbides is assumed to be a secondary process. For ease of analysis the carbon-atom ratio,* pxCy, of austenite in equilibrium with ferrite which is convex with minimum curvature radius p, and the carbon-atom ratio, PxCY, of that ferrite in equilibrium with austenite are assumed independent of location on the ferrite-austenite interface. Since these carbon contents vary with the radius of curvature of the ferrite, p, their assumed positional independence must be held as an approximation. The consequences of these assumptions have been developed approximately by zener3 and Hillert,4 and the resulting equation for a platelet has been applied to bainite by Speich and cohen5 and Kaufman, Radcliffe, and Cohen.8 The Zener-Hillert equation* for plates is: The analysis of Hillert is supported by that of Hor-vay and cahn7 which involves no mathematical approximations but does include the assumption that the a/y interface coincides with an isoconcentration line. The solutions of Horvay and Cahn for elliptic paraboloids are replotted in Fig. 1. The shape of the paraboloid is expressed in terms of the ratio of the principal radii of curvature at its tip, A =p1/p2, which is also the ratio of the minor to the major axis of the elliptic cross section. The Zener-Hillert equation for plates is also plotted. The agreement is within a factor of two for (pxyaCr - xyC )/(xyC - PxCaY) between 0.5 and 100. This is the range of interest here and in most other work on bainite. The original form of the Zener-Hillert equation was the form given above with the right-hand side replaced by (pxCya -xCy)/(PxCya). This replacement is not appropriate here. 11) THE EXPERIMENTAL PROCEDURE Alloys were prepared and three kinds of experiments carried out. Continuous-cooling-transformation experiments were carried out on wires by measuring temperature and resistance during continuous cooling. Isothermal-transformation experiments were carried out on wires by measuring electrical resistance as a

Jan 1, 1968

By K. G. Davis, P. Fryzuk

The diffusivity of silver in liquid tin has been determined, using the capillavy-reservoir technique, over the temperature range 250° to 500°C. The new value, D = 2.5 x 10'* exp(-2480/ RT) sq cm per sec, differs from that obtained by other workers in an earlier investigation. The analysis of data from the capillary-reservoir technique is discussed. In a recent investigation of the solidification of dilute alloys, values for the diffusion constant of silver in liquid tin were required in the analysis of the formation of impurity substructures. AS a result, measurements were made of the diffusion constants in the temperature range 250° to 500°C (melting point of tin 232°C), for the alloy concentrations used in the solidification experiments and at higher concentrations, to verify previous determinations.I)2 The capillary-reservoir method was adopted, using experimental procedures similar to those followed by Ma and Swalin,1 with the main exception that radioactive silver was used in the present investigation to facilitate solute-concentration measurements. EXPERIMENTAL PROCEDURE a) 100 ppm Samples. Glass capillary tubes of 2 mm inside diameter and approximately 5 cm- long were sealed at one end, evacuated, and filled with tin of 99.999 pct purity. The region of shrinkage near the mouth was cut off, and the tubes were then placed in a graphite holder and immersed, with the open end up, in an unstirred bath of alloy containing 100 ppm Ag 110, where they remained for periods of up to 30 hr. On removal from the bath they were cooled by an air blower. The bath was kept under a small positive pressure of argon, and the temperature controlled to within +1°C. A 10-hr diffusion period was used in the majority of the tests, scatter on runs of less than 5 hr being rather large. The procedure outlined above was chosen in preference to putting alloy in the capillary and pure tin in the bath, in order to avoid segregation when the tubes filled with alloy were first solidified. To minimize segregation when the diffusion period was complete and the capillaries again solidified, the earlier samples were held in thin-walled silica tubes which could be cooled very rapidly. Later tests were made in precision-bore Pyrex tubes, to eliminate effects caused by variations in the capillary diameter. No consistent differences in diffusivity as measured in the two types of tube were detected. After removal from the glass tubing, the samples were sectioned into 2.5 mm lengths and counted for y activity, using a scintillation counter with fixed geometry. Samples were also drawn directly from the bath and counted, so that values for C/C,, the ratio of the weight of Ag 110 in the sample to that in the bath, could be obtained. b) 5000 ppm Alloy. To check for possible effects of concentration, the silver content of the bath was increased to 5000 ppm. Complete mixing was found to have taken place in the capillary after a 10-hr period at 300°C. It appears that the greater density of the alloy was sufficient for buoyancy forces to cause instability in the alloy-tin interface, leading to rapid convective mixing. For the 5000 ppm alloy, therefore, the bath was of pure tin and the capillary tube was filled with alloy. With this arrangement, values of D consistent with those for the 100 ppm alloy were obtained, Fig. 1. CALCULATIONS OF DIFFUSIVITY The terminology used applies to a capillary of pure tin immersed in a bath of alloy. 1) Error-Function Method. under the present experimental conditions, the rod of liquid tin into which silver is penetrating may be considered semi-infinite. Assuming the concentration at the mouth of the tube to remain constant at Co, the concentration C at distance x from the mouth of the tube at time / is given by3 Plots of the inverse error function of (1 -C/Co) vs .v gave straight lines passing through the origin with slope 1/2-, x being corrected for shrinkage both on solidification and while cooling to the melting point (total correction about 6 pct at 500°C). Values for log D obtained in this manner are shown in Fig. 1. A least-squares fit to the relation D = Do exp(-Q/RT)

Jan 1, 1965

By Larry G. Hayes

Development of the Bowers-Campbell zinc deposit, located in the Shenandoah Valley two miles northwest of Timberville, Va., was commenced in 1956 by the Tri-State Zinc Co. The occurrence of lead-zinc mineralization in this area has been known for many years, but the first serious exploration program was initiated in 1951 by the geologic staff of Tri-State Zinc Co. Ordovician dolomites. The deposit is approximately 700 ft long, 100 ft wide, and 475 ft thick. Its projected plan has an elongated ovoid shape, where- as the profile appears boot-shaped with the upper portion outcropping. Vertical cross sections show the lense as having been thrust-faulted along certain bedding planes. The movement along these bedding thrusts varies greatly and in one case, has offset the deposit so as to divide it into an upper and lower orebody. The breccia lense strikes parallel to the N 34" E strike of enclosing strata.

Jan 9, 1960

Large scale mining of Mesabi taconites may have moved nearer to realization with the arrival of the latest model Linde Jet-Piercing machine at Reserve Mining Co.'s Babbitt, Minn. property. When the machine is placed in operation it is expected to pierce blast holes in the hard taconite beds up to 10 times faster than is possible with existing drilling equipment. The new primary blast hole drilling machine has been designated the JPM-3, and is the successor to the JPM-1, in operation at Erie Mining Co.'s taconite mines at Aurora, Minn. The size of primary blast holes which can now be pierced has increased from a nominal 61 in. diameter to 71 in. diameter and maximum hole depth has increased from 35 ft to 47 ft. Development has progressed to where 71/2 in. holes can be pierced with the same speed as 61/2 in. holes. Piercing progress is controlled by electronic blowpipe descent controls. Other features of the JPM-3 include: automatic burner ignition from the operating cab; heated and air conditioned operating cab designed for all-year operation; mechanical improvements for sub-zero operation common to the Mesabi, and redesign of wearing parts for longer service with minimum maintenance. The 40-ton machine is self-propelled. Power, oxygen, and cooling water lines trail from the machine. Jet piercing is based on combustion products of oxygen and a liquid fuel such as kerosene. The flame, jetting from a burner at speeds of about 6000 ft per sec, disintegrates layers of spallable rock. The burner is cooled by water which is then directed through orifices around the periphery of the burner. The water changes to steam and carries the spallings out of the hole. The equipment used in Jet-Piercing is essentially a tractor-mounted blowpipe containing a combustion chamber and nozzle, which is in effect a miniature rocket motor, from which the supersonic combustion gases emerge to do their work.

Jan 1, 1952

J. T. LITTLETON, JR., ? Corning, N. Y. (written discussion?).-This. discussion will add little that has not been brought out but will show how the problems encountered in the Corning Glass Works were overcome. The chief points of consideration in any equipment are, first, the work the equipment is called upon to do; second, the installation; and, third, the man who will use it. These three points should determine the type of apparatus adopted. If only rough measurements, merely a little better than the eye, are desired, the cost of the instruments should be considered; but if accurate temperature control is necessary, the cost of the equipment deserves only small consideration. There is no question that the real problem for any factory is the installation, making sure that the elements really give the temperatures desired; also, the instruments must be so designed that any man can use them.

Jan 12, 1919

By J. P. Morgan, J. R. Dawson

A review of Jones & Laughlin's Vesta coal preparation plant flowsheet in 1959 indicated that, of the three sizes making up the company's metallurgical product, the -48-mesh fraction offered the greatest potential for improvement. Efforts to improve quality and yield were directed toward the use of froth flotation. After laboratory and plant tests were completed, it was decided that treatment of the entire -@-mesh fraction of the coal mix by flotation was a significant step forward in providing better coal quality and recovery. Reduction of ash in the metallurgical coal from 6.75 to 6.25% provided material savings at the coal washer, coke plant and blast furnace. The Vesta preparation plant of the Jones & Laughlin Steel Corp. is located on the Monongahela River, eight miles south of Brownsville, Pa. This plant is capable of cleaning 2400 tph of a mixture of Pittsburgh seam high volatile coals from the Vesta and Shannopin mines to produce a metallurgical coal of 6.75% ash and a steam coal containing 14% ash. Heavy media vessels are utilized to upgrade the coarse coal while launders and tables handle the -1/4-in. fraction of the raw coal feed. Cleaned -1/4-in. coal goes to boot classifiers where the 48 mesh material settles and is removed by bucket elevators. This 1/4x48 mesh material is then sent to centrifugal dryers for dewatering. As designed, the -48 mesh fraction overflows the boot as a 7 to 8% solids slurry and is recovered by cyclones and a thickener and then dewatered by filtration. The products of the heavy media circuit, the launder-table-boot-dryer circuit and the cyclone-thickener-filter circuit, are combined to constitute the shipped metallurgical coal. The Vesta-Shannopin mix is combined at Jones & Laughlin's Pittsburgh and Aliquippa Works with purchased low and medium volatile coals for the production of metallurgical coke. A review of the preparation plant flowsheet in 1959 indicated that of the three sizes making up the metallurgical product, the -48-mesh fraction, containing 16.7% ash, offered the greatest potential for improvement of coal quality. This fraction was considered low, averaging 55%, while the rejects averaged only 33% ash. It was evident that while the boot overflow fraction represented only 6% of the product mix, a reduction in ash to 6 or 7% would reduce the ash of the metallurgical coal by 0.5%. The original plant flowsheet handling the boot overflow (Fig. 1) consisted of ten 14-in. cyclones treating 70% of the overflow and producing a 48x150-mesh underflow and a -150-mesh overflow. The cyclone overflow was combined with the remaining 30% of the boot overflow to constitute the feed to a 150-ft thickener. The cyclone underflow and the 48x325-mesh thickener underflow were fed to vacuum disk filters for dewatering prior to combination with the coarse metallurgical coal. The thickener overflow stream containing the -325-mesh material was split, 40% being recycled directly to the plant water system and 60% being flocculated and clarified in an 85-ft thickener. The underflow of this thickener was pumped to waste. Efforts to improve quality and yield on the -48-mesh coal were directed toward the use of froth flotation early in the investigation. A review of the fine coal flowsheet indicated that three streams should be considered for treatment by froth flotation. These were the -325-mesh thickener overflow, the -150-mesh cyclone overflow and the -48-mesh boot overflow. Flotation of the thickener overflow was considered basically to improve recovery by upgrading the reject stream so that it could be fed to the filters along with the thickener and cyclone underflows. The overflow from the thickener contained 3.7% solids and had an ash analysis of 33%. Flotation of the cyclone overflow and boot overflow were considered to upgrade coal quality as well as yield. Treatment of the cyclone overflow, a 5.4% solids slurry averaging 27% ash, would eliminate the coal thickener and provide a feed of flotation concentrate and cyclone underflow to the filters. Treatment of the boot overflow would eliminate both the cyclones and thickener and feed only flotation concentrates to the filters. Flotation feed in this

Jan 1, 1962

By P. Barnes

(Read at the Wilkes-Barre Meeting, May, 1877.) THE tabular statement accompanying this note shows the money cost in each of the three departments of manufacture, of 17 leading items, and also the proportion (expressed in a decimal fraction) which each of these items bears to the total cost. The statement can hardly be taken for more than an average illustration of the clear showing of ratios and of results which may be made by such an arrangement, for not only will these items vary from month to month in any given works, but the methods themselves of manufacture differ widely in different works. It is obvious that such a statement, however useful it may be, must be submitted with but exceedingly little explanation or discussion, or with none at all, for the reason that to enter at any satisfac-

Jan 1, 1878

By Ernst F. Eurich

Alexander Parkes patented in England in 1851-52-53 a process for desilvering lead by means of zinc, making use of the greater affinity of silver for zinc than for lead, discovered by Karsten in 1842. The efforts in England to develop it commercially were not particularly successful, nor was the attempted introduction into the United States. This last was not surprising, as it was about the beginning of our Civil War, and at that period there was very little lead-bullion produced in the United States and there was no field for the process here. There was at that time on Staten Island an establishment that pattisonized lead, probably from Rossie, N. Y., and Chester, Pa., and possibly some Spanish lead, but the production of lead-bullion in the Far West had not yet begun. In 1864, Edward Balbach, of Newark, N. J., patented in this country a process for desilvering lead by means of zinc, and in 1867 Edward Balbach, Jr., patented a " movable black-lead retort with a neck, placed in a furnace," for the purpose of distilling the alloy of zinc, lead, and the precious metals. A brief comparison of the Parkes and the Balbach processes is interesting. The Parkes process as practiced in England consisted in stirring into silver-bearing lead, melted in a kettle, from 1 to 2 per cent. of zinc, cooling, skimming the alloy of lead, zinc, and silver that rose to the surface, liquating it in an iron retort, distilling the residual rich alloy in fire-clay retorts, thus regaining the zinc, and refining the desilvered lead at a low heat in a shallow cast-iron pan that formed the hearth of a reverbera-tory furnace. If the lead was too impure, it was first softened

Jan 1, 1913

By J. B. Umpleby

The function of gas in the development and production of oil has far-reaching consequences that should be emphasized. The technical aspects of the subject have recently had a great deal of attention but less thought has been given to fundamental concepts underlying oil and gas law and the many customs and practices that have grown up in the industry. I shall review briefly the advance in knowledge of the subject and attempt to relate these concepts to legislative, judicial and operating problems. Early writers on oil and gas in Pennsylvania noted their close association in oil pools and their contemporaneous decline in output; also, that as gas pressure decreases so does production, that new offset wells reduce the output of existing wells, and even that tubing a well lengthens its flowing life. Expanding gas was deduced as the principal expulsive force. These fundamental observations had been made at least as early as 1880.1 They were treated, however, as academic considerations and did not greatly influence law or practice for many years except to instill into all operators an urgent desire to hasten offset drilling in order to obtain as much of the flush as possible. The most noteworthy later advance in knowledge came in 1926 when Beecher and Parkhurst published their paper on Effects of Dissolved Gas upon the Viscosity and Surface Tension of OiL.² This paper added to the old idea of an expelling force the concept of a modifying agent that actually changes the physical characteristics of the oil and facilitates its movement through the pore spaces of the reservoir rock. Largely since the publication of this paper, intensive study and concerted effort have been given to means of using to a maximum, in producing oil, these combined properties of gas. This is shown clearly by the number of papers dealing with the subject, and the new and revived terms now widely used to express thought, such as the expressions gas energy, reservoir pressure, reservoir energy, gas-oil ratio, bottom-hole pressure, beaning, tapered tubing and back-pressure. These terms, some of which are

Jan 1, 1932

Joseph Esrey Johnson, Jr., had already achieved rare distinction as an able metallurgist, clear thinker, brilliant author, and wise consulting engineer to bankers and operators; he had achieved the essentials of a great career when dcath cut short his activities on Apr. 4, 1919, in the forty-ninth year of his age. He belonged to a family of iron blast-furnace men and mine managers. His father, Major J. E. Johnson, after serving with distinction in the Army of the North, identified himself with the iron mines and blast furnace at Longdale, Va., with which he was connected during almost his entire business life. It is significant, that, during those troublous times of reconstruction in the South, he enjoyed always the affection and respect of his neighbors and associates alike. From him his son obtained not only a thorough training in blast-furnace practice and iron mining, but great personal courage and force of character. His mother, who survives both her husband and sons, possesses rare intellectuality, humor and a tenderness and human sympathy which those who were privileged to know well J. E. Johnson, Jr., recognized beneath his exterior of aggressiveness and will power. In a recently published analysis of the qualities which characterize the world's great men, three traits stand out preeminently; viz., independence, courage, and intellectuality. Each of these characteristics J. E. Johnson, Jr., possessed in extraordinary degree. His early education was obtained under a private tutor at Longdale, and this circumstance probably enhanced a natural tendency to independence of character and individuality which, however, under the control of his unusual power of straight thinking and clear analysis never allowed him to go far astray. It has been said of him that if once he set his mind to a problem, however knotty, he scored a bull's-eye before the subject was dropped. His manner of attacking a subject involved first mastering the details of the available knowledge; then, putting this acquired information to one side, with an untrammeled mind blazing out a path of his own, so clear, so well-defined, and expressed in such simple terms that he illuminated the whole subject without distorting the original data or discussion. His two books, "Blast-furnace Construction in America" and "The Principles, Operation, and Products of the Blast Furnace, "on the iron blast furnace together form the most comprehensive, the most enlightening, and the most useful treatise on the subject ever produced in any language. But his ability did not end with the mastery and elucidation of principles enunciated by his predecessors; his own

Jan 1, 1920

By J. A. Snyder, W. L. Finlay

SEVERAL notable studies of the effects of sub- stitutional solutes have been reported. Outstanding among these for its elucidation of general principles, is the summarized work of Hume-Rothery and coworkers.1 For a systematic study of the effects of substitutional solutes on the mechanical properties of the solvent lattice, the work of Brick, Martin, and Angier² on copper; of Frye and coworkers³,4,5 on copper and silver; and of Lacy and Gensamer6 and of Austin7 on iron may be mentioned. Titanium is one of the few elements offering the possibility of a similar study of interstitial solutes since, unlike most metallic elements, it exhibits extended solid solubility for most of the interstitial solutes—hydrogen, boron, nitrogen, oxygen, and carbon. This paper reports a survey of the effects of dilute solutions of nitrogen, oxygen, and carbon on the mechanical properties of high-purity alpha titanium. Previous Work: Van Arkel and De Boer showed" that high purity titanium was quite ductile and De Boer, Burgers and Fast established".' that not only were oxygen and nitrogen very soluble in solid titanium but that, long before the limit of solid solubility of either had been reached, these interstitial solutes rendered the metal brittle. Their electrical resistance data as a function of

Jan 1, 1951

By D. Y. Geng, Syd S. Peng

This paper analyzes the effects of geology and mining methods on surface subsidence factor, angle of draw and angle of critical deformation based on the results of 40 longwall subsidence profiles in the Northern Appalachian coalfield. Several equations were derived to show the relationships between those parameters. Furthermore, the equations were transferred and plotted in the form of several monographs for convenience of applications.

Jan 1, 1982

By M. G. Fowler

A GENERAL decline in copper production for most American producers occurred during the past year as a result of shortage in available labor. Few noteworthy technical developments have been reported; undoubtedly, many changes and improvements have been made but have not been reported because of lack of time. During the war years through 1944 the pressure for sustained high production has been of prime importance and during 1945, with slackening of production, many operators were faced with the problem of catching up on repairs and maintenance of plants, with inadequate labor supply. In hydrometallurgy there were some important developments that undoubtedly will be reported during 1946. Several operators in the Southwest have instituted experimental leaching programs to exploit low-grade oxidized and mixed ore bodies. The Bureau of Mines is conducting pilot-plant experimental work to determine the possibility of producing a satisfactory sponge iron at an attractive cost from deposits of iron ore and coal in Arizona. The sponge iron would be used for the production of cement cop¬per. The cell house of the Inspiration Consolidated Copper Co. at Inspiration,

Jan 1, 1946

By D. Watson, T. J. N. Grainger-Allan

A technique for studying the mechanism of the froth flotation process in which continuous froth removal does not take place but, instead, an equilibrium is reached between froth and pulp is described. A flotation cell, specially designed to facilitate equilibration, and froth and pulp sampling procedures are described. The main advantage of the technique is that the ability to measure the steady-state froth height allows froth-stability effects to be separated from pulp-process effects. In the flotation of hematite front quartz, linear relationships are found between airflow rate and froth height and between airflow rate and the ratio at equilibrium of mass of values in froth to mass of values in the pulp. A simple mechanistic interpretation of these results is given. It is suggested that froth-stability effects may play a more important role than hitherto allowed. In particular, the way in which concentration and size distribution of gangue particles may affect overall flotation rate is shown.

Jan 1, 1975