Search Documents

By C. R. Ramachandra, C. C. Patel

Flotation of chalcopyrite from a low grade ore was studied by using different xanthates and dixanthogens as collectors and by conditioning the flotation pulp with oxidizing gaseous systems. The improvement in the recovery of chalcopyrite with the oxidizing systems was mainly due to the auto-activation of chalcopyrite, leading to the enhanced adsorption of xanthates and dixanthogens even when the latter were formed by oxidation of the xanthates. With air or oxygen as oxidizing system, the amount of ethyl xanthate required at pH 8.5 was much less than normally employed in the industry, the recovery being 97-99% of chalcopyrite with a concentrate of 24% copper. With isopropyl and isoamyl xanthates, the recovery was improved but the grade was lowered. By conditioning the pulp with air-CO2 or oxygen-CO2 mixture, the recovery was lowered with ethyl xanthate only, mainly due to the depressant action of bicarbonate formed. Flotation with dixanthogens gave cleaner concentrates of chalcopyrite. because iron pyrite did not float with these collectors. Of the dixanthogens tried, diisopropyl dixanthogen gave the highest recovery, 99% chalcopyrite with a concentrate containing 28.5 to 30% copper, when the pulp at pH 8.5 was condi-tioned with air. Isopropyl dixanthogen was found to be the best collector of all the xanthates and dixanthogens studied. It was found that the adsorbed ethyl, isopropyl and isoamyl xanthates at chalcopyrite surface, activated by cupric sulfate, and at iron pyrite surface were oxidized to the corresponding dixanthogens to different degrees in presence of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture.' The dixanthogen formed at chalcopyrite surface was, however, firmly adsorbed while that at iron pyrite surface was easily desorbed. Since dixanthogens formed have greater hydrophobicity than the corresponding xanthates, as revealed by contact angles,1,2 the former were expected to improve the flotation results. It was, therefore, thought desirable to find out the effect of air, oxygen, air-carbon dioxide mixture and oxygen-carbon dioxide mixture on the selective flotation of chalcopyrite when individual xanthates were used as collectors. The effect of direct use of dixanthogens as collectors on the selective flotation of chalcopyrite was also investigated. For these studies, low grade chalcopyrite ore, received from the Indian Copper Corp., Ltd. (I.C.C.), Ghatsila, Bihar, was employed. At the milling plant of the I.C.C., chalcopyrite is floated at a pH of 8.5, employing ethyl xanthate as collector. EXPERIMENTAL Materials Employed: XANTHATES - Ethyl, isopropyl and isoamyl xanthates of potassium were prepared in a pure state by the methods described earlier.4 A 0.03% aqueous solution of a xanthate was freshly prepared in air-free distilled water for flotation studies. DIXANTHOGENS - Diethyl, diisopropyl and diisoamyl dixanthogens were prepared by the oxidation of xanthates by iodine and purified by extraction with petroleum ether. A 0.03% alcoholic solution of dixanthogen was used as a collector. FROTHER - A 0.2% solution of pine oil in ethyl alcohol was employed. SODIUM CARBONATE - A 0.4 N solution was used. ORE - The composition of the -100 +200-mesh size (Tyler standard) powdered ore, as determined by standard methods of analysis, was: copper 1.57%, iron 10.29%, sulfur 3.15% and acid insolubles 66.10%. Iron present as chalcopyrite (CuFeS2) was 1.38%, while that present as iron pyrite (FeS,) was 1.37%. Both chalcopyrite and iron pyrite were found to be liberated from the gangue minerals and from each other, as observed under a microscope. Flotation of Chalcopyrite with Xanthates in Presence of Different Gaseous Systems: Fifteen grams of -100 + 200-mesh size ore were shaken well with 100 ml of distilled water. The pH of the pulp was adjusted to 8.5 by the addition of sodium carbonate solution. Then 0.1 ml of xanthate solution (0.005 lb xanthate per ton of the ore) was mixed with the pulp, and the latter together with washings transferred to a

Jan 1, 1963

By J. Richard Maier

Short-range mine planning (less than five years) previously was accomplished using contour and isopac maps, pencil and paper, an abacus, and our lucky quarter. Through the use of both micros and mainframe time sharing, Glenrock Coal Company (GCC) has been able to virtually put the old equipment away (except the problem solving quarter). In the process, GCC has saved many man-days and eliminated the more tedious parts of mine planning, such as picking elevations off a map with an engineer's scale and repetitive calculations. These savings have allowed GCC to do a more extensive job of mine planning as well as offer more alternatives, making GCC better prepared for possible economic changes. Mine planning, simply, involves looking at what has been done and deciding what needs to be done using various constraints. The application of this concept is not as easy as it sounds. The need for experience and insight cannot be replaced by a machine, but machines can supplement a person's ability by doing the bookkeeping and the repetitive work. Through the application of computers and their accessories, GCC has brought mine planning to a more modernized state. The following paper will detail the development and use of one system as used at GCC. Please note: In the figures and tables following, some of the data has been altered to protect confidential information used in mine planning.

Jan 1, 1983

By J. W. Snavely

WITH all the advantages of handling bulk materials by means of belt conveyor also go some problems, one of the most persistent being that of cleaning. When sticky materials are being carried; the build-up of material on the return idler rolls results in difficulty of belt training. Much attention has been given to the problem of cleaning conveyor belts, and a great variety of cleaning devices have been developed. Even the best involve troublesome maintenance, and none can completely remove the fine particles imbedded in the belt cover, which cause rapid wear of the return idler rolls, and at the same time, of the belt cover as well. One of the major rubber companies has been promoting a two-way belt system, in which the conveyor belt is given two successive 90" twists at each end to enable it to carry material in both directions simultaneously. For many years the flat belt transmission industry has installed quarter-turn and half-turn twists in countless numbers of instances. While quarter-turn and half-turn twists in transmission belts is a familiar application, the 180" twist apparently has never been previously attempted with a conveyor belt. About a year ago, two officials of the National Iron Co. of Duluth, Lester and Lewis Erickson, proposed twisting the return run of a conveyor belt on an installation that they were designing for one of the major iron ore producers. Since then the soundness of the idea has been demonstrated, both in theory and by practical test, with the result that the installation of two conveyor belts involving the twisting of the return run is now under way. These two installations are designed to have the return run of the conveyor belt twisted 180" as it leaves the snub pulley at the head drive. The clean underside of the belt is thus placed against the idlers on the return run as well as on the carrying run. Just before it enters the tail pulley, the belt will be twisted an additional 180°, restoring it to its normal position. Because this twisting of the return run of a conveyor belt is a radical departure from accepted practice, an elaborate and extensive test was conducted early in 1950 to demonstrate that this twisting of the return run could be done successfully, also to establish application data for accomplishing this twisting, and to determine if any special equipment would be required. In studying this concept of twisting the return run of a conveyor belt, a number of problems need to be solved, primarily the ones brought about by deliberately introducing an unequal distribution of stress across the conveyor belt and controlling that maldistribution of stress, while confining it to the return run portion. The tension conditions existing in the return run of a conveyor belt are clear to all designers. First, the return run carries the initial or slack side tension of the conveyor belt, the tension that must be supplied to the return run to provide proper frictional contact between the belt and the driving pulley so that the necessary power can be transmitted from the driving pulley to the belt without slippage. This slack side tension is supplied to the belt by means of takeups, either of the gravity type, which can be vertical or horizontal, or by means of the screw type. With inclined or declined belt conveyors the slope tension also must be considered, which is the tension imposed by the weight of the belt hanging from the top pulley. This slope tension frequently can furnish part or even all of the initial tension required. The maximum value of the slope tension will be at the top pulley, and it decreases in direct proportion to the length. In addition to the foregoing, it frequently is desirable to impose arbitrarily additional slack side tension to provide sufficient tension at the loading point at the tail, so that the belt will adequately support its load between the carrying idlers. Design Conditions for Twisting A number of design conditions exist, which must be satisfied successfully to accomplish the twisting of the return run without exceeding normal working limits in any portion of the conveyor belt. It is obvious that the belt edge, in its relation to the center of the belt, must stretch in making a twist, because as the twist is accomplished, the belt edge travels through a longer path than does the center of the belt. It is further obvious that if the edge of the belt is stretched, a redistribution of stress in the belt is required to allow this edge stretching. Moreover, this stress will be unequal across the width of the belt, having a maximum value at the edges, with a minimum value at the- center of the belt. With correct initial tension in the return run of a conveyor belt, the existing slack side tension will be unequally distributed when a twist is introduced. A condition then exists in which the edge stresses,

Jan 1, 1952

By Charles Barrett

THE orientation of metal crystals and grains, both large and small,. can be determined conveniently and accurately without the use of X-ray apparatus. This seems to be appreciated by so few metallurgists that it may be useful to explain in detail the method we have found most satis-factory in the laboratory the reflection of light from crystallographic etch pits. This note includes a description of a suitable inexpensive instrument and instructions for etching various metals and for plotting the data. As the stereographic projection is used to facilitate handling the data, this note may be considered as an appendix to an earlier review of the metallurgical uses of the stereographic projection.1 Various methods involving etch pits have been used by other investi-gators, Bridgman's method2 consists of attaching the specimen to a sphere (a transparent sphere is convenient4), holding it at arm's length, and marking a spot on it when it has been turned so that the etch pits reflect light into the eye of the observer from a lamp standing behind him. It has an accuracy of about 2° and is extremely rapid. A greater accuracy can be obtained by having the reflected light fall on a screen, as has been done by Czoehralski, 5 Chalmers,6 and Schubnikov.7 All of these methods have been intended for undeformed single crystals. Tammann and his coworkers"' developed a method for estimating the number of grains in a polycrystalline aggregate having orientations in a given region of the stereographic triangle and thus obtained statistical information about deformation and recrystallization textures. While the method has had some use in recent years,9 it is not applicable to the majority of problems in physical metallurgy. Smith and Mehl10 determined orientations by plotting the directions of the sides of individual etch pits on a stereo-

Jan 1, 1940

By S. F. Frederick, W. A. Bailey

The relationship between microstructure and mechanical properties of cast 356-type aluminum alloys was studied to determine the cause of the variations in properties resulting from differences in solidification rate. It was found that variations in strength are a consequence of variations in ductility and that ductility is inversely proportional to the dendrite cell size. A mechanism is proposed to account for this correlation based on the fracture strain of the inter-dendritic silicon particles and the differential strain across dendrite cell boundaries. IT has long been assumed that permanent mold castings of aluminum are superior to sand castings because of their finer grain structure and reduced porosity.' A systematic variation of static properties was noted during unpublished studies of fatigue-strength variations with solidification rate of A356-T6. Of particular interest was the observation that for a given composition and heat-treatment, both ductility and the ultimate strength increased with higher solidification rate. Because the A1-Si system forms the basis of many alloys used for castings and welding wire, a study was initiated to determine the details of how higher cooling rates improved mechanical properties of these alloys. The results of this study are presented here. EXPERIMENTAL PROCEDURE Specimens were prepared from 356-T6 to supplement the A365-T6 alloy data from earlier studies. This allowed a comparison of behavior of alloys with substantially different strengths but with only small differences in alloy composition. The composition and heat treatment of both alloys are given in Table I. The specimens were cut from a chill plate casting,' which is a 6 by 9-in. plate, 1 in. thick, which has one end heavily chilled, and a large riser at the other so that solidification is essentially unidirectional from the chill end to the riser. Although not measured here, solidification times measured on similar specimens by embedded thermocouples are a few seconds at the chill end and up to 5 min near the riser. Specimens were obtained by cutting slabs from the plate, parallel to the chill; these represented different cooling rates, with essentially the same composition. For the tests, either 0.125 or 0.250-in. thick slabs were cut for standard 2-in. gage length specimens. The thicker specimens were tested to failure at 2000 lb per min while the thinner specimens were tested in an Instron machine at a constant cross-head speed of 0.02 in. per min. These thin specimens were intended for trans- mission electron microscopy. Some thin specimens were tested to failure while the remainder were given various amounts of prestrain. Dendrite cell sizes were measured by the linear intercept method on photomicrographs at either X100 or X50, depending on the cell size. It was assumed that the dendrite cells were outlined by the silicon particles. Determinations were made on two mutually perpendicular planes and an rms average taken. Electron fractographs of representative tensile specimens were made in the conventional manner using the two-stage replica technique.3 Samples for transmission electron microscopy were prepared by chemical milling followed by electropolishing. RESULTS AND DISCUSSION The results of the tensile tests and the dendrite cell-size determinations are given in Figs. 1 and 2. All data show the same trends, namely, a decrease in ultimate strength and elongation with increasing distance from the chill (and solidification time), and a corresponding increase in dendrite cell size. The yield strength remains essentially constant. The constancy of the yield strength was particularly significant since it indicated that variation in the solidification rate does not affect the stress required to initiate plastic flow. By plotting true stress-true strain curves as in Fig. 3, it can be seen that both

Jan 1, 1969

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By J. T. Eash, E. M. Wise

Platinum and palladium are the most generally useful, most ductile and least rare members of the platinum family. They have many important applications in the pure state but for other applications it is frequently desirable to harden them and otherwise modify their properties by alloying small amounts of the other platinum group metals with them. These alloys are frequently required to withstand very drastic forming operations and to possess certain mechanical properties to fulfill specific requirements. For these reasons a knowledge of the tensile properties and annealing characteristics of pure platinum and palladium as well as their more useful commercial alloys is important to the user and the fabricator. The present work was undertaken to fill this need. Rather brief (5 min.) annealing treatments were employed to render the data of maximum practical value and all tests were conducted upon 0.050-in. dia. wire, initially reduced 50 per cent in area by cold drawing, for the same reason. Conclusions 1. Pure (thermocouple grade) platinum reduced 50 per. cent by cold drawing exhibits the following tensile properties: ultimate tensile strength, 36,000 lb. per sq. in.; proportional limit, 27,000 lb. per sq. in.; elongation, 2.5 per cent in 2 in.; reduction in area, 95 per cent. When fully annealed by treatment at 1100°C. its properties are: ultimate tensile strength, 20,700 lb. per sq. in.; elongation, 30 per cent in 2 in.; reduction in area, 93 per cent. 2. The addition of alloying elements in moderate amounts markedly increases the strength and annealing temperature without much detriment to the ductility. The behavior and properties of variously hardened platinum alloys are considered in some detail. The behavior of a 20 per cent iridium

Jan 1, 1935

By David B. Brooks, William A. Wallace, James R. Dunn

As the conflict between the mineral industry and preservationists steadily increases, it becomes urgent to determine as precisely as possible the costs of developing vs. not developing our domestic mineral resources so that enlightened mineral policy decisions can be made. A simple discounted cash flow equation is suggested as an approach to assigning a public-interest dollar value to mineral resources. Present value of a piece of land underlain by a mineral resource is taken as equal to the discounted cash flow derived from the resource corrected for present and future surface land values. The equation is effective as a base for mineral aggregate resource planning for metropolitan areas if transportation cost differences are substituted into the cash flow component. Suitably modified, the equation can be fitted readily into an existing computer simulation program for aggregate mineral resource planning in metropolitan areas. However, because of the lack of accurate input, the equation is less effective for other mineral commodities such as base metals and coal. Nevertheless, within a somewhat philosophical context, the equation still has utility and is effective in defining the problem of public interest values for minerals other than mineral aggregates.

Jan 1, 1972

By H. H. Power, C. H. Pishny

When an oil operator becomes a party to a proration agreement he may wonder, with good cause, whether production prorated .today is merely deferred until tomorrow or whether oil might be lost. Various types of evidence obtained from production records when studied quantitatively are of great assistance in arriving at definite conclusions. A study of individual examples cited in this paper leads towards some solution of the problem, particularly when they are considered in the aggregate. Many production curves on various pay horizons were studied. A disappointingly large number of these were of contributory value, but inconclusive. However, there were enough curves of similar type from the Wilcox sand at Earlsboro, Bowlegs, Seminole City, the Cromwell horizon at Little River, and the Simpson dolomite at Valley Center, Kansas, from which reasonably definite conclusions were drawn. Assuming that deferred production is later made up with no increase in ultimate recovery, a curve (Fig. 1) shows the normal flowing and pumping life of a composite well, contructed by the family curve method. The initial production of the well shown is 1700 bbl. daily and the allowed production is 25 per cent. On this basis the average daily allowed rate for the first month is 425 bb1., or the area BCDE, which is equivalent to the area AFDG under the normal decline curve. The potential production for the second month is 1500 bbl. and the allowed production 375 bbl. daily. By this procedure a potential curve for each succeeding month is obtained (points A, H, I, J and K). If the well is opened it should produce somewhere near its potential curve for a short period and then decline at a more rapid rate than the potential curve. This theoretical analysis is basic. Actual examples exhibiting all points raised by the ideal curve are rare. Proration in the Mid-Continent area has been effected mostly by leases rather than by individual wells; hence a well may produce any

Jan 1, 1931

By B. M. Larsen, W. E. Shenk

This paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable —that is, the time interval between successive reversals—should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one lLminimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: I. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potenti-ometric control instrument, to correct any tendency toward temperature unbalance between ends of the furnace. 3. A second "maximum temperature

Jan 1, 1945

By Frank W. Osterwald

Violent, spontaneous destruction of coal faces and ribs during, what are commonly called, bumps endangers and at times destroys life and property in mines of the Book Cliffs coalfield, Carbon County, Utah. Because these mines supply much of the coking coal for the West Coast steel industries, mining is necessary, although costs are high and operating conditions are very difficult at times. As operations continue, mining will go to greater depths, and the difficulties will increase. Whether or not mining can be continued successfully depends in part on whether or not incidence of bumps can be controlled successfully. For this reason, the U.S. Geological Survey, at the request of and in cooperation with the U.S. Bureau of Mines, undertook a study of the Sunnyside No. 1 mine to determine what geologic factors were related to the incidence of bumps. This report presents the preliminary results of that study and indicates that some observable geologic features in the mine may be related directly or indirectly to bumps, and that other features may be used to infer stress distribution around workings that will aid in design of roof support measures. Coal is mined in the Sunnyside No. 1 mine from depths as great as 2500 ft by room-and-pillar methods. The surface topography is rugged with many steep cliffs and deep canyons, hence the load on the coal varies greatly within short distances. Much of the Sunnyside coal is under high stress, and while being mined, it shatters continuously' and falls from the face. Continuous shattering (bumping) makes mining easy, but if the shattering is interrupted, greater stress is built up and violent bumps may result when the coal is mined.

Jan 4, 1962

By Frederick L. Knouse

THE south border of Espirito Santo begins about 400 km. north of Rio de Janeiro and extends along the Atlantic Coast northward some 325 km. and inland 100 to 150 km. The area under consideration, where quartz crystal of strategic grades has been mined, extends from 19° to 21° and 30" south latitude; and from 40° to 41° and 30" west longitude. This includes the central part of Espirito Santo, chiefly south of the Rio Doce from the Atlantic ocean, and west across the border into Minas Gerais near the town of Aimores, in the municipalities of Aimores, Minas Gerais; Baixo Guandu, Santa Teresa, Santa Leopoldina, Colatina, Joao Neiva, Fundao and Domingo Martines, Espirito Santo (Fig. 1). During 1943 and the first half of 1944, this region accounted for approximately 3 to 5 per cent of the quartz crystal produced in Brazil. Shipments of crystal have been made chiefly by rail to Rio de Janeiro. This region is serviced by the E. F. Minas-Vitoria and E. F. Leopoldina to Rio de Janeiro through Vitoria; and by the E. F. Minas-Vitoria and E. F. Central do Brasil through Bello Horizonte, Minas Gerais to Rio de Janeiro. The major deposits are accessible from the railheads by dirt roads, some being 5 to 30 km. off the road, reached by trail. In 1943 and the first half of 1944, the bulk of the production was from inter mountain marshes and adjoining hillside alluvial placer deposits in the zone surrounding the town of Santa Teresa. Most of these deposits were formed from the erosion of pegmatites, quartz veins and pockets in the gneiss, with minor quantities produced from miarolitic cavity fillings in the granitic rock. EARLY OPERATIONS Mining of quartz crystal in this region began in 1928, and has been stimulated by the market demand for military uses. Before 1936 little attention was given to it, either in Espirito Santo or eastern Minas Gerais. From 1936 to 1941 the Japanese sent agents to various points of production or potential production to acquire quartz through purchase. They bought crystal as small as 10 grams. Since 1941 only the United States and Great Britain have received quartz from Brazil. The United States purchases crystals of loo grams and larger for strategic purposes. The first known discoveries were made either in the municipalities of Aimores, Minas Gerais, or in Baixo Guandu, or Domingos Martines, Espirito Santo. Marketable quartz crystal was first found either in the massive quartz replacement veins of the Victor Hugo mine in the municipality of Domingo Martines, or in the large cores of quartz in the pegmatites near Baixo Guandu, extending into Minas Gerais. PRODUCTION The production of quartz in Espirito Santo from 1936 through 1941 as recorded

Jan 1, 1946

By Clifford Frondel

THE aluminum oxide known as corundum has several varieties that have been used as gem materials since ancient times. These include the red variety called ruby, the blue variety sapphire, and the asteriated types of ruby and sapphire. Asteriated sapphire was known to the ancients under the name of astrios, and descriptions of this gem were given by Pliny and other early writers. The relation of these gem materials to each other as varieties of a single species, corundum, was first clearly established by Haüy in 1805 and J. M. Güthe1 in 1809. Natural gem corundum is obtained principally in Ceylon, Siam, Burma, India, and Australia. Star sapphires and rubies always have been highly prized and in recent years have become particularly popular in the United States. Natural star rubies of large size and fine quality are extremely rare and rank with large and fine emeralds and diamonds as the most valuable of gem stones. Interest thus attaches to the recent success in commercially synthesizing star sapphires and rubies of a size and perfection unmatched by nature.

Jan 1, 1954

Jan 8, 1950

By Gordon M. Yocom

A PROPER consideration of the subject of this paper should include economic aspects as well as the technical phases of the metallurgy, production, and properties of the product. The metallurgical phases of the processing and properties of the product will be considered only from practical aspects and within the scope of the writer's experience with tonnage production. The Bessemer process was invented 85 years ago and became important because it put steel manufacture upon a larger and less costly basis. In America the Bessemer production has declined for many years and has not maintained its proportionate place with the rapid advances of the open hearth. The achievements in the open-hearth field were attained by the greater number of technical people attracted to that branch of the industry. The antipathy of technical students for the older and less popular Bessemer field gradually weakened the forces defending it and retarded the development of new and better methods. In Europe the economic advantage of the basic Bessemer process has not been overlooked and the tonnage usually is greater than that of the open hearth. The acid process has been the subject of renewed attention in America during the past few years and those who are more familiar with it are striving to show that the method is too valuable to abandon. A considerable tonnage of Bessemer-blown metal, in both molten and ingot forms, used in connection with the open-hearth practice makes it an important auxiliary unit to the industry. This practice aids in modifying the price level of heavy remelting scrap in addition to speeding up the open-hearth operation. The use of Bessemer steel has continued not only because of periodic economic advantages but also because of certain inherent qualities of machinability, weldability and stiffness, which are valuable for many applications. The properties of stiffness and rather high reaction to cold-work require some modification in order to meet the demands of modern methods of processing, which involve cold-reduction and cold-forming. At least one factor contributing to the stiffness of this steel is the relatively high phosphorus content of the acid product. The phosphorus content of the Thomas or basic Bessemer steel of Europe is considerably lower than the normal acid product in America. The American industry has continued the use of the acid process chiefly for the reason that the available ores are more easily adapted to this process from both metallurgical and economic standpoints. In European practice the basic process is necessary with the highly phosphoric ores available and it is sustained to some degree by the sale of the rich phosphate slag as a by-product. The basic process was used in this country at several plants many years ago, but was abandoned for economic reasons. A part of the past history of these trials is given here because the author believes it has not been published and it has some bearing on the subject of this paper. The information is authentic to the extent that

Jan 1, 1941

By J. Burns Read, Charles H. Fulton

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By A. B. Kinzel

SILICON, unfortunately, is not in the same category as some other metals with respect to the absolute value of the highest purity material prepared. Tucker, in England, and Becket, in this country have devel-oped procedures for the purification of silicon, and Becket's process has made industrially available silicon of a purity of 99.8 per cent or better. However, even the term "silicon metal" may be a paradox to some people, although not more so than the term "amorphous" as applied to silicon. These terms come from commerce, and "metal" is used to distinguish industrially high-purity silicon from ferrosilicon, silicon-aluminum, and other high-silicon alloys. Alloys of iron and silicon with 95 per cent Si or less are known as ferrosilicon, with a designation of silicon content where necessary, and the terns "silicon metal" is invariably applied to the grades containing 96 per cent Si and higher. The Becket method of purification was referred to in a monograph on the Alloys of Iron and Silicon, and the Tucker procedure was described in some detail in that publication.1 In order to get silicon of still higher purity, a sample, prepared by the Becket method, analyzing 99.84 per cent Si, 0.020 Fe, 0.016 Al, 0.005 Ca, 0.025 C, 0.033 per cent 02, 0.006 H2, 0.006 N2, and 0.001 per cent Mn, was crushed to pass a 100-mesh sieve said further purified by a modification of Tucker's procedure. This modification differs from Tucker's method in that after treatment the 100-mesh alloy was centrifuged to remove the last traces of acid. Our directly determined analysis of this purified sample shows: Si, 99.952 per cent; Fe, 0.009; Al, 0.012; Ca, 0.003; C, 0.006; or 99.982 per cent. Silicon by difference equals 99.97 per cent. The variation between silicon by difference and silicon as directly determined is important. Although Tucker mentions the amount of insoluble matter in commercial silicon both before and after his treat-ment, he does not mention the existence of carbon in the alloy; neverthe-less, lie reports silicon by difference. Any final figure as to purity obviously results from agreement between direct determination and

Jan 1, 1939

By J. C. Reed, P. J. Shenon

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

By P. J. Shenon, J. C. Reed

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935

The Elk City district is in north-central Idaho about 60 miles east of Grangeville and near the headwaters of the South Fork of the Clearwater River (Fig. 1). At the height of its boom in the early sixties, Elk City had a population of more than 2000 people, Published estimates of the placer production from the district range from $10,000,000 to $18,500,000. Although the first quartz-vein location was made as early as 1870, very little gold was extracted from quartz ores until after the completion of the American Eagle mill in 1902. Between 1902 and 1932 a total of from $750,000 to $1,000,000 was taken from about six properties. General Geology Distribution of Rocks Banded gneiss (Fig. 2) is the most aburldant bedrock in the Elk City district. It is interbedded with schist and quartzite and ill some places these rocks have been intruded by sills and dikes. Banded gneiss prevails in the western part of the area whereas schist prevails to the southeast. Augen gneiss occurs for the most part as irregular bodies, which lie transverse to the trend of the banded gneiss and schist. It is largely confined to two areas; one of which extends from east of the American Eagle mine westward as far as the Black Pine mine, a total distance of about five miles, and another area of about two square miles in the vicinity of the California-Idaho placer mine. Quartzite is fairly abundant. In addition to the bands of the latter interbedded with gneiss and schist, some large lenses crop out in the southeastern part of the dik-trict near the southern contact of the area underlain by granodiorite. Granodiorite crops out over a large area and extends northeastward

Jan 1, 1935