Search Documents

By B. A. Wilcox, A. H. Clauer

The steady-state creep of TD Nickel NL + 2 001 pct TltOz) has been studied orer the telirperatve range 325&apos; to 1100O and the stress range 15,000 to 36,000 psi. At high temperatures (aboue 0.5 T& gran-boundary slzding is the )nost znportant )node of creep deformation, and the steady-state creep rate, is, can be related to stress and temperature by: where Q = 190 kcal pev mole and n has an unusually high value of 40. A creep mechanism based on cross slip of dislocations around The O2 particles can satisfactovily explain the low-temperature (T < 0.5 T,) cveep behavior, and the follo wing relation is applicable: Q, (a) is found to decrease from 57 to 46 kcal per mole as the stress is increased from 32,000 to 36,000 psi. THERE have been a variety of theories proposed to explain the influence of dispersed second-phase particles on the yield strength and flow stress of metals, and these have been reviewed recently by Kelly and icholson.&apos; However, only several attempts2"4 have been made to develop mechanistic treatments which characterize the creep behavior of dispersion-strengthened metals, and to date these have not been fully evaluated experimentally. weertman2 and Ansell and weertman3 proposed a quantitative creep theory for coarse-grairzed dispersion-strengthened metals, based on the concept that the rate-controlling process for steady-state creep was the climb of dislocations over second-phase particles, as suggested by choeck. The theory predicted that the steady-state creep rate, <,, was proportional to the applied stress, a, for low stresses and that is a4 o for high stresses. The activation energy for creep, Q,, was equivalent to that for self-diffusion, Qs.d., in the matrix. Some limited experimental evidence in support of this theory was obtained on a recrystallized Al-Alz03 S.A.P.-type alloy by Ansell and Lenel.6 Ansell and weertman3 also developed a semiquanti-tative theory for high-temperature creep of lineg-rained dispersion-strengthened metals in order to explain their results on an extruded S:A.P.-type alloy, which had a fine-grained fibrous structure. They suggested that the rate of dislocation generation from grain boundaries was the rate-controlling process, and fitted their results to the equation: where Q, was found to be 150 kcal per mole, i.e., QC- 4Q,.d. in aluminum. Similar high activation energies for creep7-&apos;&apos; and tensile deformation" of dispersion-strengthened alloys have been observed by other investigators for S.A.P.,&apos;" indium-glass bead omosites, and Ni + A1203 alls.&apos; There is no general agreement regarding the mechanisms involved in the creep of dispersion-strengthened metals, and this is due in part to the lack of detailed studies relating the structures of crept specimens to the mechanical behavior. The present investigation on thoriated nickel was undertaken with the aim of studying the structural changes which occur during creep of a dispersion-strengthened alloy and rationalizing the observed mechanical behavior in terms of the creep structures. EXPERIMENTAL METHODS The material used in this investigation was 1/2-in.-diam TD Nickel bar, which contained 2.3 vol pct Tho,. Obtained from E. I. duPont de Nemours & Co., Inc. The final fabrication treatment by DuPont consisted of -95 pct reduction by swaging followed by a 1-hr anneal at 1000°C. Transmission and replica electron microscopy revealed that the material had a fine-grained fibered structure with an average transverse grain size of -1 p and a longitudinal grain size of 10 to 15 p. Selected-area diffraction indicated that the fiber axis was parallel to (OOl), in agreement with the results of Inman eta1." All creep specimens were vacuum-annealed at 1300°C for 3 hr prior to testing. Transmission electron microscopy showed that the only structural change due to annealing was a slight decrease in dislocation density, confirming the reported high degree of structural stability.13 Furthermore, recrys-tallization or grain growth during creep was never observed. The structure typical of uncrept material (after the 1300 C, 3-hr anneal) is shown in Fig. 1. The grain boundaries are predominantly high angle and. although some areas show a tangled cell structure, the grain interiors are relatively dislocation-free. Individual dislocations are strongly pinned by the Tho2 particles; i.e., very rarely did dislocations move within a thin foil. The grey "halos" around some of the larger particles which protrude out of the foil surface arise from contamination in the electron microscoge. The Tho, particle size ranged from -100 to IOOOA, and the distribution is shown in Fig. 2. The technique used to obtain the data in Fig. 2 consisted of dissolving the nickel matrix in acid, collecting the Tho2 particles on cellulose acetate, and measuring about 1000 particle diameters in the electron microscope. Similar results were obtained by measuring about 600 particles in thin foils, an; the average particle size was found to be 2r, = 370A. Using the data in Fig. 2 (annealed structure), the mean planar center-to-center particle

Jan 1, 1967

By Y. H. Liu, G. W. Powell

Thin foils made from the gold-rich region of- short (0.15 mm)Au-Ag diffusion couples annealed at 880°C for 1 hr were examined in ax electron microscope and the structures were compared with that of pure gold subjected to identical heat treatments. The couples underwent Plastic deformation (bending) during the diffusional anneal. The foils prepared from the diffusion zone have a higher dislocation density and incidence of subboundaries than pure gold. The plastic bending of the couple can be interpreted in terms of the climb of edge dislocations, which are pavallel to the bend axis, along the direction of diffusion. THE interaction of lattice defects during interdiffu-sion between two metals has been considered by several investigators. In particular, da Silva and Mehl,1 Barnes,&apos; and Bardeen and Herring3 have proposed models based on interactions between point and line defects to account for the Kirkendall effect (marker movement). Each of these models is based on dislocation climb, which can either add or remove lattice planes, induced by an under- or supersaturation of vacancies. A theoretical treatment of the nucleation and growth of voids by the condensation of vacancies has been presented by Seitz.4 Stresses can arise in a binary diffusion couple as a result of the vacancy flux and the gradient in the lattice parameter. rinkmman&apos; has investigated the effects of diffusion-induced stresses on void formation; the results of his analysis suggest that voids can form and grow under the influence of these stresses in the absence of an excess vacancy concentration. The relationships between vacancy supersaturation and diffusion-induced stresses and void formation have been elucidated also by Balluffi and seigle6 who concluded that the stress generated by a vacancy supersaturation aids the growth of voids. Experimental evidence which indirectly shows that stresses are produced by chemical diffusion has been obtained by several researchers.2,7-9 This evidence consists in part of the observation by light microscopy of the formation of subgrains, a process characteristic of the high-temperature deformation of some metals during creep.&apos;0 More striking, however, is the plastic bending of short (0.2 mm) Cu-Ni couples observed by Barnes2 and of boron-doped silicon crystals reported by Queisser.9 Diffusion-induced dislocations in iron and silicon have been investigated by Ainslie et a1.11and Schwutte and Queisser,12 respectively, the former using transmission electron microscopy and the latter an X-ray transmission technique. Matthews and Crawford13 observed the formation of boundaries by the climb of interfacial misfit dislocations in thin, vapor-deposited Au-Pd couples diffused in situ in an electron microscope. In order to obtain additional information on the phenomena associated with defect interaction and diffusion-induced stresses in binary couples, an electron transmission study of foils prepared from the diffusion zone of short Au-Ag couples was undertaken. The initial objective was to investigate the processes occurring at various points of the diffusion zone. Subsequent research demonstrated that foils could be prepared only from the gold-rich region of the diffusion zone using the technique described herein. EXPERIMENTAL PROCEDURE Preparation and Annealing of the Diffusion Couples. The couples were made from annealed, high-purity (99.999 pct). polycrvstalline gold and silver sheets (0.075 mm thick). Shall (0.075 by 5 by 17 mm) elec-tropolished coupons of gold and silver were pressure-bonded by heating the two metals in a graphite device to 770°C and holding at this temperature for approximately 30 min. The quality of the bond was ascertained by metallographic examination at 150 times. Each couple subsequently was annealed at 880°C for 1hr; under these conditions, the extreme portions of the

Jan 1, 1968

By AIME AIME

T HE Board of Directors of the A. I. M. E. held a meeting at Institute headquarters on Jan. 28, 1921. There were present 10 directors and 14 guests, the secretary and the assistant secretary. The following actions of the Executive and Finance Committees were approved: Wilkes-Barre Meeting, Sept. 12 to 17, 1921; authorization of Oregon Section; authorization of Upper Peninsula Section; appointment of Philip W. Henry and Thomas H. Leggett on special committee on Code of Ethics; and presentation of five copies of Raymond Memorial Volume to T. A. Rickard, who edited it. The By-Laws of the Ohio Section were approved. The resolutions in reference to the payment of certain contributions and assessments to the Library Board of the United Engineering Societies, adopted by the Board of Directors on June 27, 1919, were rescinded, and the resolution adopted that the income of the James Douglas Trust of $100,000 be paid over to the Library or otherwise applied by it for the purpose of maintaining the Scientific Library of this Institute in such manner as may be deemed advisable in furtherance of the purposes of such trust, and that said income shall be paid on account of and included in. the assessment levied by the United Engineering Societies on the Institute for the maintenance of the joint libraries of the Founder Societies.

Jan 1, 1921

By Ross Glanville

INTRODUCTION The Optimum Production Rate (OPR) is one of the most important parameters in the evaluation of a mineral deposit. The OPR can also be expressed as the Optimum Mine Life (OML) in years since the expected mine life is determined by dividing the OPR per year into the estimated ore reserves. Unfortunately, very little time and effort has been directed towards the determination of the OPR. Instead, "rules of thumb" are often applied to select a mine life without due consideration of the economic implications of such a selection. A "justification" for a particular production rate is often based on a pre-conceived arbitrary requirement for a mine life of 5, 10, or 15 years, for example. In this paper it is demonstrated that such arbitrary selections for high-grade/low-tonnage mines (such as many underground gold/silver deposits) often lead to sub-optimal results. In fact, an apparently uneconomic deposit at an arbitrary production rate may be economic at the OPR. Consequently, investment opportunities may be overlooked if one analyzes mine properties based on arbitrary production rates. This paper analyzes the interrelationships of variables such as production rates, capital and operating costs, cut-off grades, discount rates, metal prices, etc. The analysis shows that the OML for high-grade/low-tonnage deposits is often in the range of two to four years. Although such mine lives intuitively appear too short to many individuals, it should be noted that, in the past, much of the mining industry became familiar with the economics of large scale mining operations. The rules of thumb developed for such large scale operations should not be applied to high-grade/low-tonnage mines such as many of the underground gold deposits. DEFINITION OF OPTIMUM PRODUCTION RATE The OPR is selected on the basis of maximizing the net present value of the after-tax cash flows. However, as discussed later in this paper, the production rate selected for a particular mine may be somewhat higher or lower than the theoretical OPR as a result of other variables such as: 1) the probability or expectation of additional reserves being discovered 2) the likelihood of being able to custom mill nearby deposits owned by others 3) the configuration or attitude of the orebody, which may place upper limits on the production rate 4) the residual, or salvage values, of the mine/mill facilities COMPARISON BETWEEN DIFFERENT PRODUCTION RATES For an orebody with definite physical cutoffs*, or boundaries (such as faults or unconformities), the total ore reserves at different production rates may be identical. Consequently, for such an orebody, varying production rates result in differing mine lives. Although the metallurgical recoveries, the mine dilution, and other similar physical parameters may vary slightly at different production rates, the major differences are the capital costs and operating costs per ton. The ramifications of these differences are especially important at low production rates (up to approximately 1000 tons per day), but can also be significant at higher production rates.

Jan 1, 1985

By A. L. Holley

The application of scientific methods to the investigation of natural laws and to the conduct of the useful arts which are founded upon them, is year by year mitigating the asperity and enlarging the outcome of human endeavor. More notably, perhaps, are these the facts in that system of productive and constructive arts of which engineering is the general name. In metallurgical engineering especially, within the period of our own recollection, how rapid has been the rate and how wide the scope of progress: the scientific discovery and mining of metalliferous veins; the economical separation and reduction of ores of every grade; the production and regulation of high temperatures; the varied improvements in the manufacture of iron, in saved heat and work, in uniformity and range of products; and, most important of all, the creation and the utilization, to be counted by the million tons a year, of the cheap constructive steels. Wonderful as this range and degree of development may appear to the public eye, the close and thoughtful observer must, nevertheless, conclude that neither the profession nor the craft of engineering may congratulate themselves too complaisantly, but that they should rather acknowledge to each other the embarrassing incompleteness of the union between engineering science and art. There is a small school of philosophers whom we may designate as original investigators, men who come close to nature, who search into first principles, and who follow that scientific and therefore fruitful method by which the relations of matter and force are discovered, classified, and brought within the reach of practice. These wonderful men do not indeed create the laws of nature, as they sometimes almost seem to, but they go up into the trembling mountain and the thick darkness and bring down the tables upon which they are written.

By H. E. McKinstry

MOVEMENT on a fracture of irregular shape can cause local widening of the fissure and thereby offer freer channelways for circulation of ore-depositing solutions. This influence, coupled with large areas of wall rock available for reacting with ore solutions in brecciated and shattered ground can account for locally active deposition of metals and the resulting ore shoots. Such irregularities in the fracture system may be caused by local variations in the strength of rocks and by pre-existing lines of weakness, especially if these stand at favorable angles to certain components of the fracturing stress. Therefore correct interpretation of the mechanics of fracturing should permit deductions as to structurally favorable places on unexplored portions of the vein system. INTRODUCTION IT has long been recognized that movement on a curved or irregular fault surface is capable of separating the walls in certain portions of the fault, but until very recent years the importance of this mechanism as a factor in localizing ore shoots has escaped proper recognition. A short time ago W. H. Newhouse&apos; presented a careful analytical study of displacements and their corresponding open spaces. For reasons that will be discussed later, it frequently happens that portions of the vein which are favorably oriented are not merely wider but also richer than the average. In many cases the widening with its accompanying richness coincides with very minor changes in the dip or strike of the vein, irregularities that commonly escape notice unless the vein is mapped in detail and a careful geometrical analysis made. While the relationship between the width of the vein and the changes in dip or strike has been recognized as a matter of observation, the irregularities have been accepted as more or less the result of accident. There has been very little effort except in isolated cases to find out the causes of these changes in dip or strike. Yet it is clear that if the causes can be recognized and expressed in terms of geologic structure the geologist will know where to look for repetitions of these favorable conditions either on extensions of the same vein or on adjoining veins. Any lack of understanding of the causes is due to the limitations of our ability to interpret our observations and not to the sheer capriciousness of

Jan 1, 1941

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the &apos;economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40&apos; above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

By R. V. Ramani, G. W. Luxbacher

Computer simulation of mine ventilation system is rapidly becoming an essential tool in mine planning and design. This Paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve primarily for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1980

By David E. Hyatt

The chemical attributes of cyanides have long been exploited in ore pro- cessing schemes for the recovery of copper, molybdenum, gold, silver, and other metal values. Blast furnacing operations are significant unintentional producers of cyanides which find their way into process waters. Many of the more than 20,000 electroplating facilities in the United States utilize cyanide plating baths and generate cyanide containing wastes. As social, political, and economic pressures for water quality attainment, maintenance, and preservation grow, the requirements for the development of treatment technology to control cyanide levels in wastewater become increasingly apparent. Just as the chemistry of the cyanide ion 1s an integral part of its industrial applicability, so must this chemistry be a fundamental part of any decomposition or removal technology used to control its level in effluent or recycled waters. The complexity of this chemistry is substantial and it cannot be considered in a superficial or cursory manner if control system design is to be both efficient and reliable.

Jan 1, 1975

By Warren B. Davis

Introduction If a subject this broad were to be covered in even moderate detail, it would require a set of books about the size of an encyclopedia. Since an acceptable length for this paper is a small fraction of one book, it will have to consist of a few samples of the subjects that I think are the most pertinent to World Fossil Fuel Economics. I plan to discuss the trends in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, gas and coal; the prospects of synthetics; and some of the effects of government regulation of fuel economics. World Energy Demands Fig. 1 shows Free World energy consumption by principal areas for the period from 1950 to 1970 and a forecast for the period from 1970 to 1985. These figures include only the measurable forms of energy. An example of energy consumption that is not measured is the wood a peasant might cut in the forest and bum in a fireplace to heat his home. This omission probably is a very small part of the total. This forecast is not identical with that of Wayne E. Glenn (see Page 22), but the differences in total energy consumption are not significant. The U. S. consumption, which was 55 percent of the world total in 1950, had declined to 45 percent by 1970, and is expected to decline further to 38 percent by 1985. Western Europe has consumed 28 percent of the total from 1950 to 1970 and is expected to lose share slightly between 1970 and 1985. The most spectacular gainer is Japan, which increased consumption from 2.5 percent in 1950 to 7.5 percent in 1970, and is expected to reach nearly 17 percent by 1985. The over-all Free World total has grown from 62 quadrillion Btu (equivalent to 29 million B/D of crude oil) in 1950 to 151 quadrillion by 1970, an average growth rate of 4.5 percent/year. This total is expected to grow at a rate of 5 percent/year between now and 1985, reaching 315 quadrillion Btu (equivalent to nearly 150 million B/D). Fig. 2 shows which fuels supplied this energy between 1950 and 1970, and gives an estimate of how it will be supplied between 1970 and 1985.

Jan 1, 1971

By Charles White Merrill, James W. Pennington

No metallurgical process developed in the 20th century compares with froth flotation in its effect on the mineral industry. Processes like gravity - concentration, amalgamation, and pyrometallurgical reduction are of ancient origin; others like cyanidation and electrolytic reduction were well established by 1900. Such metallurgical processes as heavy-media separation, ion-exchange, and solvent extraction belong to this century, but their influence is small compared with froth flotation. Data collected by the U. S. Bureau of Mines* in a canvass of 202 froth flotation plants reveal that, in 1960, 198- million tons of material was treated to recover 20-million tons of concentrates which contained approximately $1 billion in recoverable products. SIGNIFICANCE OF FLOTATION Froth flotation as described in this chapter refers to a wet process for separating properly ground mineral particles into two or more products. It involves the separation of mineral particles from each other in a liquid pulp by means of air bubbles. Finely crushed ore is agitated in water with the addition of air or other gases. Various chemicals and oils are added to cause the selected mineral particles to attach themselves to the air or gas bubbles. These bubbles, carrying the mineral particles, rise to the surface where they are removed in a froth, while the other particles remain suspended in the pulp. The earliest flotation divided the raw material into two products: a bulk concentrate that was removed as a froth and a tailing that remained in the flotation machine. The froth usually contained the valuable constituents. The successful application of such a process depended on the recovery of a single concentrate from which one or more valuable constituents could be recovered by a chemical or smelting process. With the advance of the art, however, the principle of selective flotation, by which two or more relatively pure products could be recovered from complex raw materials, was evolved. Other chapters in this volume describe the developments during the last 50

Jan 1, 1962

By R. Schuhmann

Available thermodynamic data applicable to copper smelting systems are collected and tabulated, and the important gaps are pointed out. A few examples are given of estimations which can be made from the available data. An experimental research program is proposed to supply the thermodynamic data that appear most essential to better quantitative understanding of the chemistry of copper smelting. The proposed program is designed also to shed specific light on the practical problems of slag losses and magnetite behavior. OPPER smelting, from flotation concentrates to V-/ blister copper, is conspicuous among the large scale chemical processes which are conducted with only relatively incomplete knowledge of the physical chemistry involved. For example, no common metallurgy text explains adequately why copper enters the matte phase while iron enters only to the extent that sulphur is left over after satisfying the copper. Explaining this important phenomenon as a manifestation of the greater affinity of sulphur for copper than for iron is unsound because the affinities of copper and iron for sulphur are about the same at smelting temperatures. As will be shown, other affinities are really decisive in the relatively clear-cut separation of copper in the matte. In contrast, thermodynamic studies have contributed much to our understanding of copper refining, zinc oxide reduction, magnesium production, steelmaking, etc. For each of these processes, the important reactions are clearly recognized, and fair to good quantitative values of the free-energy changes and equilibrium constants are available. Such data have proved to be of constantly increasing practical value in process development and improvement. Work in other fields has furnished much thermodynamic data applicable to copper smelting systems. In fact, several promising starts have been made in applying such data to specific smelting problems. Kelleyl made an appraisal of the possibilities of recovering elementary sulphur from low grade matte. His calculations and compilations of thermodynamic data have represented the starting point for much of the work in this field, including the present survey. Huang and Hayward2 nd Aksoy3 used thermodynamic methods in the study of copper losses in reverberatory slags. Peretti4 used thermodynamic data in explaining the chemistry of converting. The recent publications of Darken and Gurry"." and of Darken,&apos; dealing with the iron-oxygen and iron-silicon-oxygen systems, respectively, present equilibrium data that are applicable to copper smelting systems. Also additional data were reported recently on the affinity of sulphur for copper, manganese, and iron8 and on the sulphur pressures of iron-sulphur melts." The survey presented in this paper was made as the basis for planning an experimental program on the thermodynamics of copper smelting. Few researches on the chemistry of copper smelting have been reported in recent years, so that a reappraisal and coordination of old and new data are essential if further work is to take the directions of maximum value. The experimental program is now in progress, and the plan of attack is outlined at the end of this paper. Progressive Oxidation and Desulphurization of Copper-bearing Liquid Phases: The chemical activities of sulphur and oxygen are two of the most important thermodynamic yardsticks to be applied to copper smelting processes. Virtually the entire smelting and refining sequence involves a series of systems characterized by decreasing sulphur activity and increasing oxygen activity. In this section, therefore, an attempt is made to define and explain these activities in terms of equilibrium partial pressures of SO2, s2, and O,. Also, estimates of these quantities are presented, the estimates being based largely on calculations presented in a later section of this paper. The sequence of steps from raw flotation concentrate to fully oxidized copper ready for poling involves progressive and controlled oxidation. Iron is oxidized and enters the slag. Sulphur is oxidized and leaves in the gas. Table I summarizes several important features of this oxidation and desulphurization sequence, starting at the beginning of the matte blow in the converter. The top line gives in order the principal smelting and refining stages up to fully oxidized copper, plus the additional step, not used commercially, of oxidizing all the way to Cu,O. In the second line are shown the principal copper-bearing liquid phases which characterize the process. Through most of the sequence the copper

Jan 1, 1951

By Robert E. Green, T. Hinton

The velocities of the three possible modes of elastic-wave Propagation have been calculated for single-crystal aluminum at 1-deg intervals throughout the standard steveographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy propagation and specirzen axes are presented as arrows drawn within the standard triangle. The orientation factors associated with dislocation nzotion on the primary slip system only and also on all twelve slip systenzs have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing--7aue resonant specivnen hazle also been calculated. The relevance of these results to ultrasonic attenuation measurements is discussed. DUE to the widespread use of ultrasonics in the investigation of the properties of solids a number of authors15 have discussed in detail the theory of elastic-wave propagation in solids. In this paper the modes of wave propagation are evaluated according to the procedure suggested by reeen&apos; for the case of single-crystal aluminum at 1-deg intervals throughout the standard stereographic triangle. The wave speeds are presented in the form of contour diagrams within the standard triangle. The deviations between the direction of maximum energy propagation and the normals to the wave fronts are presented as arrows drawn within the standard triangle. The orientation-de pendent factors (orientation factors) associated with dislocation damping as derived in the preceding paper6 have been calculated for the case of aluminum at 1-deg intervals throughout the standard triangle. The orientation factors for dislocation motion on the primary slip system only and on all twelve slip systems are presented in the form of contour diagrams, for both the traveling- and the standing-wave conditions. The relevance of these results to ultrasonic attenuation measurements is discussed. ELASTIC-WAVE PROPAGATION Three waves can be propagated in a linear elastic homogeneous anisotropic medium. The velocity of propagation v of each of these waves in a medium of density p can be obtained from the determination of the eigenvalues and eigenvectors of the matrix equa- The A&apos;s are a series of moduli which are functions of the elastic constants cij and the direction cosines 1, m, and n of the specimen axis. In the case of cubic single crystals where there are only three nonzero elastic constants cll, c12, and C, the A&apos;s are, The solution of Eq. [I] will give the wave speeds (eigenvalues) and the direction cosines a, 0, and y of the particle displacements (eigenvectors). To obtain the direction of maximum energy flux requires the calculation of the energy-flux vector ET with com- w is the angular frequency, A, the amplitude, and v the velocity of the wave. The direction cosines a, b, and c of the energy flux vector are then given by

Jan 1, 1967

Jan 1, 1909

By Richard W. Smith

KYANITE, long known to occur in Georgia, did not excite commercial interest until about 1930. Investigations revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumula-tion from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not&apos; more than a few feet. The larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersham County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habersham County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanite-mica schist belt in Habersham and Rabun counties will be discussed in this paper.

Jan 1, 1936

By M. C. Leverett

THE dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the vis-cosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability" to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indi-rectly. However, it is expected that work along lines similar to this present under-taking will help materially in solving these problems. Previous workers in this field have inves-tigated the two-phase systems, water-gas,1 water-oil2 in unconsolidated sands, and water-gas3 in consolidated sands. The ex-tension of the study of the flow of hetero-geneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.2 Correlation and interpretation of data were made by methods analogous to those used in two-phase work. The relative permeability to a phase-the effective permeability divided by the permeability of the system to a homogeneous fluid-was employed through-out in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two inde-pendent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically. The gas fraction was deter-mined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accu-rate numerical results. Reasonable precision and reproducibility were sought.

Jan 1, 1940

By John H. Walthall, Raymond L. Copson, Travis P. Hignett

In October 1942, the War Production Board requested the Tennessee Valley Authority to undertake investigations to determine the feasibility of producing alumina suitable for reduction in aluminum cells, from clays and other domestic materials, by a lime-sintering, soda-ash leaching process. The work was undertaken by the chemical engineering staff of the Authority under the general direction of the War Metallurgy Committee of the National Academy of Sciences. The investigation included small-scale tests to determine the most suitable conditions for the process, and construction and operation of a pilot plant to obtain data for evaluation of the process and for design of a plant. The results of this investigation are described in the present paper. Sources of Alumina Alumina for the commercial production of aluminum is obtained from bauxite by the Bayer process. The tremendous demand for aluminum for wartime uses is causing rapid exhaustion of the high-grade bauxite deposits in the United States. On the other hand, there is an abundance of aluminous materials such as clay and lower grades of bauxite, which are not suitable for treatment by the Bayer process because of their high silica content. The Tennessee Valley Authority has conducted research and pilot-plant work for more than 5 years on methods for the production of alumina from clay and low-grade bauxite. Particular attention has been given to the high-grade white kaolin found in Carroll County, Tennessee. Exploratory drilling has demonstrated that at least 4 1/2 million tons of kaolin containing in excess of 34 per cent AlzOI is available in this area by strip-mining methods. It has been estimated that hundreds of millions of tons of clay of similar quality occur in the Tennessee Valley region. The Process The process is illustrated in the flowsheet (Fig. I), and consists essentially of the following steps: I. Heating a mixture of clay and limestone to form a sinter containing calcium aluminate and dicalcium silicate. z. Leaching this sinter with a dilute sodium carbonate solution, to form a sodium aluminate solution and a calcium carbonate, calcium silicate residue, which is discarded. 3. Treating the sodium aluminate solution with carbon dioxide to precipitate aluminum trihydrate and regenerate the sodium carbonate solution, which is recycled. 4. Heating the aluminum trihydrate to produce alumina. The process was considered promising because of the abundance and cheapness of the two raw materials, clay and limestone; and because, as compared with an acid process, smaller amounts of critical

Jan 1, 1944

By Arthur F. Colombo, David M. Hopstock

The Lake Superior region contains extensive deposits of potential iron ore in the form of fine-grained oxidized taconite. To help assure utilization of this resource in an environmentally sound manner, the U.S. Department of the Interior, Bureau of Mines, is conducting bench- and pilot-scale research using wet high-intensity magnetic (WHIM) separation. The advantages and disadvantages of WHIM separation in comparison with other feasible beneficiation methods are discussed. Pilot plant results are given for a flowsheet in which WHIM scavenging is used in conjunction with selective flocculation and flotation. A mathematical model for use in process optimization is given. Practical aspects of matrix selection and separator design for WHIM separation of fine particles are discussed.

Jan 1, 1980

By H. M. Howe

The chief purpose of this note is to call attention to the triaxial diagram as a convenient means of illustrating the properties of slags, and by this example of its use to commend it to those inclined to graphical studies having other possible applications. Explanation.—In the common or di-axial diagram, the properties corresponding to any point are determined by its perpendicular distance from each of two axes. For example, in an ordinary stress-strain diagram the properties of a given point in the curve are, first, a stress cd so many pounds per square inch, because its perpendicular distance from the horizontal axis of the diagram corresponds by the vertical scale to that stress; and second, a strain or elongation of so many per cent., because its perpendicular distance from the vertical axis corresponds by the horizontal scale to that elongation. It happens that, as a matter of convenience, we habitually place these two axes at right angles to each other; so that our measurenieilts happen to be made not only at right-angles to

Jan 1, 1899

By G. M. Schwartz, D. M. Davidson

THE Duluth gabbro outcrops containing sulphides of copper, nickel, and iron are located on both sides of State Highway No. 1 an airline distance of 8.5 miles southeast of Ely in northeastern Minnesota. The region of known sulphide occurrences includes parts of sections 5, T. 61 N., R. 11 W., and parts of sections 25, 26, 32, 33, and 34, T. 62 N., R. 11 W. These sections, given in Fig. 1, are all in Lake County, Minnesota. Part of the area, which lies entirely within the Superior National Forest, is shown on the topographic map of the Ely quadrangle. The original discovery was made in 1948 when a small pit was opened in weathered gabbro rubble for use on a forest access road. A shear zone had caused unusual decomposition in this glaciated area, and the resulting copper stain was noted by Fred S. Childers, Sr., an Ely prospector, who began searching the outcrops along the base of the intrusive. He was joined in further exploration by Roger V. Whiteside of Duluth. In the summer of 1951 a small diamond drill was moved into the area and a hole 188 ft deep was drilled, passing through 11 ft of glacial drift into sulphide-bearing gabbro. This paper is a preliminary report on the geology of the newly discovered ore. The Duluth gabbro is one of the largest known basic intrusives and may be defined as a lopolith.&apos; It extends northeastward from the city of Duluth as a great crescent-shaped mass that intersects the shore of Lake Superior again near Hovland, 130 miles to the northeast, see Fig. 2. The distance around the outside of the crescent is nearly 170 miles. The form of the intrusive is simple at Duluth where it ends abruptly north of the St. Louis River; at the east end, however, the gabbro splits into two elongated, sill-like masses separated mainly by lava flows and characterized by minor irregularities. The outcrop reaches a maximum width in the central part where it is about 30 miles across, and a maximum thickness of about 50,000 ft. It may be significant that the sulphides occur at the base of the thickest part. The lopolith has segregated into rock types ranging from peridotite to granite. The most abundant types are olivine gabbro, gabbro, troctolite, anortho-site, and granite. Of lesser importance quantitatively are peridotite, norite, pyroxenite, magnetite gabbro, and titaniferous magnetite. Grout estimates that two-thirds of the gabbro at Duluth is olivine gabbro. Variations in the percentages of plagio-clase, augite, olivine, and magnetite-ilmenite constitute the only essential differences found among the basic rock types. The predominant mineral is plagioclase, mainly labradorite. Plagioclase and olivine seem to have crystallized early, and the olivine rich rocks, usually troctolite, are found in the lower part. Segregations of titaniferous magnetite are abundant near the base of the gabbro along the eastern part and also occur far above the base. These have recently been described in detail by Grout.&apos; Near the top, segregation has produced a gradation to granite, or "red rock," as it is known locally. This consists of quartz, red feldspar, and hornblende. The red rock forms a zone with a maximum width of nearly 5 miles but is quantitatively unimportant from Duluth northward for 35 miles. In Cook county, where the gabbro splits, each of the two sill-like masses has a red rock top somewhat thicker in proportion to the gabbro below than in the main central mass. The intrusive ranges from coarse to medium in grain size and from granitoid to diabasic in texture. Throughout much of the Duluth gabbro in Minnesota banding and foliation are well developed, as Grout has emphasized.V he bands are mainly a result of variation in the percentage of minerals, as in troctolite with alternating bands high in olivine and in plagioclase. A few bands may consist largely of one mineral, as is true of some segregations of magnetite. Many of the banded rocks show a clearly developed parallelism of platy plagioclase crystals, and both banding and foliation are believed to conform to the floor of the lopolith. Throughout its extent in Minnesota the Duluth gabbro dips east and south toward Lake Superior. It is generally believed to extend beneath Lake Superior and is found as a smaller mass exposed along the north side of the Gogebic district in Wisconsin and Michigan. The dip at and near the base ranges along most of its length from 20 to 40°, but at places the internal banding dips even more steeply. The dip of the upper part is much less, and if it is assumed that the flows along the north shore of Lake Superior are a dependable indication, it does not exceed 15". The formations shown in Table I which are intruded by the gabbro range from Keewatin to Middle Keweenawan in age. They present a significant picture. At the top, the gabbro and its accompanying

Jan 1, 1953