Search Documents

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By Albert A. Smith

The creep properties of metals have assumed increasing importance in recent years and many investigations have been made on various phases of the problem. In the past year the annual lectures of the Institute of Metals Division1 and the Iron and Steel Division2 were concerned with this subject, and are excellent reviews. For many years the creep properties of lead and lead alloys have been investigated at the Central Research Laboratories of the American Smelting and Refining Co., and it is hoped that the present paper will contribute knowledge of some of the factors that influence creep. Lead, being a metal that recrys-tallizes readily at room temperature, is an excellent material upon which to investigate creep phenomena because of the simplicity of the apparatus needed, and it might be expected that results would apply to some extent to elevated-temperature tests of other metals. Material The creep tests of this investigation were all made on high-purity lead (99.9998+ Pb) in which the only impurity that could be detected by spectrographic and chemical means was approximately 0.0001 per cent Fe. Flat strips, 0.750 in. wide by 0. 100 in. thick, were prepared by extruding 2-in. dia. cast billets at a temperature of 250°C. This gave a material of 2 to 3 mm. average grain size with a tensile strength of j.400 lb. per sq. in. when tested at a straining rate of 5 per cent per minute. With this extremely soft material, great care was necessary in handling the specimens, to avoid distortion and subsequent recrystallization. The creep tests at 30°C. were conducted in a constant-temperature room, specially built for the purpose in the basement of an office building in which there was no moving machinery, and no vibration was detectable under the most severe conditions of shock in the adjacent surroundings. The room was well insulated and heated electrically, control being by means of a de Khotinsky regulator operating a relay. Maximum temperature variation over a period of several years has been ± 1/2°C. Specimens of the extruded strip, 16 in. long, were used for test purposes with no reduced gauge section, thus eliminating any distortion due to machining. The method of clamping and supporting the specimens is shown diagrammatically in Fig. 1. The gauge marker for the measurement of extension consisted of an aluminum strip, 0.050 in. thick by 0.75 in. wide, one end of which was ground and sanded to a precise knife-edge and fastened to the specimen by suitable pins. After the strip was fastened in place a fine scratch was inscribed just below the knife-edge by means of a sharp teasing needle. Just below this gauge scratch a short vertical mark was made so that the same point could be located and read each time. Several hundred specimens have been prepared by this method, and it was found that with experi-

Jan 1, 1941

By E. H. Fahmy, L. C. Uren

During recent years, oil producers have observed with interest the practical success which has attended the application of water as a medium for displacement of oil from its reservoir sands in the Bradford field of northern Pennsylvania and southern New York. Here, according to various authorities, additional recoveries of frorn 2,000 to 12,000 bhl. of oil per acre have heen secured by this method, after ordinary flowing and pumping. rnethods of production had practically reached the lower limit of economic operation. Notwithstanding the success which has attended the practical use of the flooding process in the Bradford field, oil producers in other regions are skeptical of its value when applied under physical conditions differing markedly from those which characterizc the Bradford field. Its usc would probably he construed as illegal in most of the oil-producing states. This general relnctance on the part of oil producers in other regions to accept the flooding process is due in large part to lack of infor-n~ation regarding the factors that influence its operation and efficiency. With the purpose of clarifying to some extent the issues involved, and of determining when the flooding proccess may or may not beeffee-tivcly ernployed, the writers have conducted a serics of laboratory exper-imentments under carefully controlled conditions, designed to indicate, the influence of various physical, chemical arid lithologic factors. These experments have not been conducted under conditions identical with those which exist at depths far below the earth's surface, so that direct quantitative comparisons with field results are not justified, hut it is believed that the experimental results at least warrant qualitative inter-pretations that may he applied to field conditions. The methods employed in the conduct of these experiments are briefly explained, and the results, together with the conclusions based thereon, arc presented. FactoRs Influencing Displacement of Oil froM SaNdS by WAteR- flooding Before presenting the experimental data, it, will he desirable to con-sider the manner in which the residual oil is retained within the oil sand

Jan 1, 1928

By N. Brown

IT has been observed that a hexagonal-close-packed crystal will undergo the same macroscopic displacements as an isotropic material if the basal plane is perpendicular to the axis of twist.&apos; Other orientations may produce both bending and twisting, but this analysis will be confined to pure torsion of a right circular cylinder. The z axis, the axis of twist, and the specimen axis are coincident. The displacements are given by Uq = rz, Ur = Uz = 0 [1] where 4 is the angle of twist per unit length. This requires rotational slip, as discussed by Frank&apos; and Wilman, which may be observed readily. The relative rotation of adjoining slip planes is simply produced by a movement of a planar grid of screw dislocations."." The screw dislocations are of the same sign and they move radially inward. For hexagonal-close-packed metals, the grid is hexagonal and the screw dislocations lie in the < 2110 > directions. The displacement of a point is the resultant of two displacements produced by intersecting screws sweeping over the point. The dislocations must pass over the point (r, o) in such a manner that its resultant displacement corresponds to the observed macroscopic displacement. If 6&apos; is measured from the [1010] direction, then for 0 < ? < ~/3, only the [1210] and 121101 type screw dislocations are needed to produce the required displacement. If n1 screws of type [1210] and n2 of type [2110] pass over a point, then, in order that Ur = 0 n, sin ? - n2 sin (/3 — 6&apos;) = 0. [2] If the tangential displacement is to be independent of 0, then n1 cos ? + n2cos (/3 —?) = N [3] where N is independent of ? and thus depends only on r. Nb is the tangential displacement where b is the Burgers vector. Since U? is a linear function of r, then N must be a linear function of r. If a2 is the outer radius and a, is the inner radius to which the plastic deformation has extended, then N = Nm2 r-a1 [4] This function meets the conditions that at

Jan 1, 1956

By Robert M. Keeney

Important recent developments in the melting and annealing of non-ferrous metals include: 1. Melting of nickel silver in the vertical ring induction furnace. 2. Electric melting of stereotype metal. 3. The rotary-drum gas-fired brass melting furnace. 4. The low-frequency coreless induction furnace. 5. Finishing annealing of brass sheets with city gas1 replacing wood in the large brass-rolling mill. 6. Electric annealing of brass and copper tubing and sheets. 7. Replacement of oil by gas and electricity in the annealing of nickel-silver shells and stampings. Melting Nickel Silver in Vertical Ring Induction Furnace Although over 90 per cent. of the output of the brass rolling mills in the United States is now melted in electric furnaces,2 until recently a considerable part of the output of nickel silver has been the product of the pit fire. The application of the electric furnace to the melting of nickel silver has been slow for several reasons: (I) Until recently no lining has been available that gave a satisfactory life in the vertical ring induction furnace when melting nickel silver; (2) the rocking arc furnace so widely used in the foundry does not appear to have been favored by the rolling mill for melting nickel silver, possibly because the gases present may affect the quality of the alloy; and (3) the exclusive rights to the use of the high-frequency coreless induction furnace (which has proved very satisfactory for melting nickel silver) for the wrought brass industry are controlled by one concern. A little over one year ago the first vertical ring induction furnace to be used for melting nickel silver in the Naugatuck Valley was placed in operation. This was followed by two more in the same mill, and by

Jan 1, 1930

By Michael A. Zappia

INTRODUCTION The San Manuel mine of Magmacopper Company is located approximately 72 km northeast of Tucson, Arizona. The mine, concentrator, smelter, electrolytic refinery and continuous rod casting are located on the west side of the San Pedro River valley. Ore Production: 58 1W mtpd Production To Date: Over 340 000 000 mt since 1956. Ore Grade: 0.70% net sulfide cu. As conceived at the present time, the San Manuel ore body is the lower half of what was originally an elliptical (In cross sect ion) cylinder same 2400 m long with major and minor cross sectional axes of 1500 m and 760 m. After emplacement, the cylinder was diagonally sliced along its long dimension by the San Manuel fault, which separated it into halves, moving the upper half same 2500 m down dip and bringing a wedge-shaped blanket of tertiary conglomerate into position over the lower segment of the cylinder. The lower segment is the San Manuel ore body. The upper part, moved down dip, is the Kalamazoo ore body. Originally, these were one ore body. The San Manuel ore body is a structurally weak and highly fractured quartz monzonite, the principal ore minerals being chalcopyrite, with small amounts of molybdenite. The present mining method is full gravity diagonal retreat panel caving by block. This is shown on Figure 2 , (Block Sequence 56, 57, 58, 59 --on the following page.) The ore mined is hoisted to the surface for transportation to the concentrator. BLOCK CAVING MINING SEQUENCE HISTORY The San Manuel mine was planned and developed as a full gravity block caving mine. It continues as a full gravity block caving mine. Since its initial start, the major changes in mining have been in the areas of ground support, rate of draw and undercut sequence. Ground weight resulting from block caving plays a dual role. It can cause extensive damage to ex- traction openings, yet it is necessary to break the ore into easily handled size. The ground- weight problem resolves itself into finding ways to make it manageable. The initial early ground support in the production areas consisted of timber sets and various combinations of steel and timber sets. This sup- port system proved unsatisfactory and a new support system utilizing concrete was developed. Concrete support, 30 cm to 45 cm thick, proved satisfactory. Rates of draw were experimented with. A draw rate of 45 cm to 61 cm (32 to 45 mt) per draw point per day was determined as optimum in con- trolling ground weight. Undercut sequence or mining sequence was recognized as a major contributing factor to ground weight. This is the most difficult factor to change. The lead time from primary development to undercut can be as much as two years. Initial Checkerboard Pattern The initial undercut sequence was in a checker- board pattern (Figure 2). Blocks Sequence 1, 2, 3, 4, 5, 6--next page.

Jan 1, 1981

By Hans Lundberg

By electrical prospecting, orebodies that do not otherwise manifest themselves at the surface may be located. Conditions favorable to success with the methods are: Favorable geological conditions, such a proportion of minerals of good electrical conductivity in the orebody as will render the latter materially a better conductor than the enclosing rock, situation of the orebody within the range of influence of the electrical currents used and in proportion to this range a sufficient area of horizontal cross section of the orebody. The result is to permit of spotting drill holes accurately and to save the expense of drilling barren ground. THE art of prospecting, like other branches of mining, has developed rapidly during the last ten years, mainly because of the advancement of mining geology, but also because of the development of "geophysical methods," which are based on the different physical characters of minerals and rocks, e. g., specific gravity, elasticity, and magnetic and electric properties. These methods have proved of great value, especially in countries where the rock is covered by soil and direct geologic investigation is out of the question. In prospecting for orebodies, the methods based on studying differences in electrical conductivity have proved most successful; for which reason, the methods of electrical prospecting have been subject to the most energetic and systematic work, especially in Sweden. This paper gives a brief description of the methods of electrical prospecting now in use, especially the new electromagnetic methods, which have not been described before. The great differences in the electrical properties, especially in conductivity, between ore minerals and rock minerals are fundamental to all methods of electrical prospecting, for which reason, the electrical conductivity of ore minerals and rock minerals has been carefully studied in connection with and previous to the development of the various methods of prospecting with electricity. Ore minerals with a metallic luster, such as chalcopyrite, iron pyrite, galena, specular iron, magnetite, etc., also graphite and a number of cows, have considerably higher conductivity than the surrounding rock and soil (see Table 1). The figures of the table denote the specific resistance W, expressed in ohms for a cube with an edge of 1 centimeter.

Jan 7, 1925

Jan 1, 1916

By H. E. Lee, P. C. Feddersen, D. R. Gittinger, G. W. Dunn, J. B. Schuettenhelm

The new Bunker Hill slag-treatment plant, designed ior, a capacity of 300 to 400 tons of hot slag per day, was "blown in" April 5, 1943. In the ensuing I5-months period, 157,530 tons of slag was processed, with an average recovery of over go per cent of the zinc and practically all of the lead contained. In addition to this high metal recovery, utilization of the waste heat in the gas and fume venting, the process has enabled the generation of 231,376 tons of steam at 250-lb, gauge. Over the first six months opcration the volume of slag treated averaged somewhat under 300 tons per day. Reclaimed dump slag made up only about 1 5 per cent of the plant feed. In October 1943, preparations for the smelting of additional tonnages of dump slag were completed and the plant capacity was increased to an average of about 420 tons of slag per day. During the nine-months interval since that date, monthly averages of 450 toils per operating day have been maintained several times. The new plant (Fig. I) is constructed in close proximity to blast-furnace operations. The fuming furnace and other necessary equipment are housed in an eastward extension of the existing blast-furnace building. Beyond this housed extension the dust-laden gas is conveyed about the perimeter of a large rectangle formed by the flues, cooling towers and baghouses. The course of a 10-ft. balloon flue, which transports the fuming furnace gas, describes the west and south perimeters. This flue connects with a set of cooling towers located at the southeast comer. The flue and cooling-tower system serving the deleading kiln constitute the north side and the two baghouses, serving the kiln and furnace operations, -border the east side. From these baghouses the several discharge gas flows are come biped and conveyed in to the rectangle, being vented to atmosphere by means of a fan through a centrally located zoo-ft. brick stack. In general, the plant design and operation follow quite closely that dictated by experience gained in years of slag-fuming practice by the Anaconda Copper Mining Go., at East Helena, Mont., and the Consolidated Mining and Smelting Co. of Canada, Ltd., at Trail, B.C., and more recently by the International Smelting and Refining Co. at Toocle, Utah. : Fuming operations at the East Helena and the Tooele plants are more or less identical. Trail practice differs chiefly in the methods employed for the storage of the hot feed slag and in the methods utilized for the handling and cooling of the fuming furnace gas. The new Bunker Hill fuming plant closely follows Trail procedure in the treatment of the furnace discharge gas while East Hclcna methods have been adopted for the storage of feed slag.

Jan 1, 1944

By H. J. Wasson, E. B. Hopkins

Throughout 1928, production of oil from Venezuela steadily increased, and at the close of the year, the output was at the rate of nearly 400,000 bbl. a day. The total for the year was approximately 106,500,000 bbl., representing an increase of about 66 per cent. over the 63,000,000 bbl. produced in 1927. Venezuela now stands next to the United States as the second largest oil-producing country in the world; and there is abundant evidence to suggest that this relationship will endure for a number of years. Reserves were notably increased in the Lake shore fields, and the potential output of the Maracaibo Basin is much greater than the current production. In spite of this, the percentage of production increase was comparatively moderate, and the rate of this increase continued to fall off slightly, as has been the case for the last three years. This does not suggest that further annual increases in Venezuelan output will not materialize; only that the rate of these increases appears to be on the decline, and that with every succeeding year the future tendency will be in the direction of a stabilized level of output. The following table shows the production trend of the country since 1925: 1925 increase over 1924, 132 per cent. 1926 increase over 1925, 80 per cent. 1927 increase over 1926, 75 per cent. 1928 increase over 1927, 66 per cent. Many factors will work to prevent a reversal of this trend, but the principal ones are strong ownership in large-acreage units, and the probable indisposition of the world market to absorb a more rapidly increasing Venezuelan output at prices profitable to the producers. The distress oil element is not a factor in Venezuela; also, any unforeseen jump, such as results in the United States from the discovery of a Seminole or a deep sand at Long Beach, or Santa Fe Springs, is impossible in Venezuela, on account of lack of means for transporting a sudden surplus of oil, and the slowness with which additional transportation equipment in the form of shallow-draft tankers can be obtained.

Jan 1, 1929

By Raymond Ward

Jan 1, 1945

By Wiley C. Buford

Gary Works No. 1 BOP Shop is a three furnace shop which went into operation December, 1965. The heat size is over 200 tons, with a substantial percentage of the production used to feed a Continuous Slab Caster. Vessels are driven by a shaft mounted bull gear and main housing utilizing eight 35 HP flange mounted motors and primary gear reducers. Torque absorption is controlled by two spring actuated torque arms. At 1:00 p.m. on Thursday, August 6, 1970, as "E" furnace was being turned down for a preliminary test, the drive side trunnion bearing failed. The furnace dropped slightly and shifted several inches north in the direction of the drive unit. The decision was made to tap the heat which was done without incident and the vessel uprighted. No attempt was made to completely drain the slag from the vessel, so as to avoid any further damage to the trunnion shaft bearing surface. The bearing failure occurred approximately four years and eight months after start up of the shop. Unfortunately ?M? furnace had gone down for a normal reline two days prior to the bearing failure, leaving the shop with only one operating furnace.

Jan 1, 1972

By Thomas E. Ban, Charles D. Thompson, Charles A. Czako

Continuous sintering-a metallurgical process for more than 50 years-has broadened from its origin in nonferrous metallurgy to present-day applications in ferrous, chemical, and nonmetallic fields. During the past year, self-fluxing sinter production has been a subject of active interest to iron metallurgists in North America. Accomplishments however, have come predominantly from Europe and proper interpretation of these reports requires an understanding of European raw materials and European economics. The technology, of course, can be applied universally.

Jan 10, 1959

By L. D. Rickets

The principles on which an art is founded are usually few and necessarily basic in nature, but he who wishes to achieve the power to select his aides and give success to important undertakings that may be entrusted to him in the future must ordinarily undergo years of drudgery in order to gain the experience that will enable him to distinguish such fundamentals through the haze of reenforcing detail that clothes and tends to disguise them. This especially applies to those who would dream dreams that may come partly true. Professor Henry B. Cornwall of Princeton was a graduate of Freiberg with mining experience in Mexico. He was my friend and mentor during my college life. In 1883 I finished my postgraduate course and had two offers of work to consider. His advice is very clear in my mind today. It was essentially as follows: I know something of the mines of Mexico and have crossed through the mountains of the West. The West possesses a vast area of mountain and valley. California has long had its gold mines, the Comstock and Gilpin County followed and now comes the discovery of Leadville. I believe the West, will become a great mining country. You can choose now to teach here or go to the mountains. Were I in your place I would go West and identify myself with mining.

Jan 1, 1932

By Robert M. Jimeson, James M. Grout

The competitive market potential for solvent-refined coal is estimated and the market advantages are enumerated. Markets are possible in combustion, railroad locomotion, and carbon electrodes. The combustion characteristics are consistent with expected air pollution restrictions on the emission of sulfur and particulate matter. A market potential of sufficient size exists to support the initiation of solvent refining in the United States. The market analysis should help fuel producers determine the advisability of their undertaking solvent refining of coal.

Jan 1, 1972

By Richard S. McCaffery, Morrison B. Yung

While assaying some copper carbonate ore from the Frazer claims, Similakameen, B. C., I noticed that on parting the gold button a deep orange solution was formed. The button gave off pink bands in the nitric acid, which became deep orange at a short distance from it; and as it traveled over the surface of the porcelain dish, it left a deep orange track behind. As the button brightened in the cupel, it appeared to have a bronze color; but I have since found that when amarillium is in large excess of the gold, the button is a very dark gray. The button parted easily. To the orange solution I added a salt (NaCl) solution, shook in a silver testbottle, and filtered. With H2S I obtained a precipitate, which I supposed due to platinum. However, on further tests, it did

Jan 1, 1903

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank&apos; standardized by the American Society for Testing Materials. Although this method of classification has been an American stand¬ard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1944

By John S. Johnson

THE purpose of this article is to describe several types of borehole lining in common use, and especially to offer a relatively new means of reducing the expense of maintaining boreholes where they are subjected to corrosive action of water flowing either inside or outside of their casing. In the Anthracite region of Pennsylvania, boreholes are used for many purposes, the principal ones being: openings between the surface and underground workings through which are passed steam, water and compressed-air lines, ropeways from surface hoists to underground rope haulages, conduits for electric power and signal lines, water-discharge lines from underground pumping stations, and inlets to mine workings for flushing material. LININGS FOR BOREHOLES The inadequacy of steel pipe for use in boreholes has long been recognized. Various substitute materials have been tried, including screw-joint cast-iron pipe (Fig. I). Cast-iron pipe, while very effective as a discharge line for acid water (mine water) being pumped to the surface, is not so effective when serving as a conduit for silt and crushed rock being flushed underground for filling mine voids. Terra cotta pipe (Fig. 2) has been used in boreholes, and lasts a long time if the glazed inner surface of the pipe remains intact. Its installation in a borehole is very difficult and is recommended only where it is certain that there will be no subsidence of the surrounding territory. Accessibility in order properly to join each section of the pipe is essential to a satisfactory job. In large water holes, where it is possible to lower a man into the hole for sealing the joints of the pipe, glazed terra cotta pipe has been used successfully for delivering mine water from pumps in the mines. For large holes used for flushing refuse into mine workings where the surface wash is shallow, standard paving brick have been used to form a tube through the wash to the bedrock. These brick are laid radially, backed by common brick and cobbles laid in cement. It is obvious that the shaft through the wash must be large enough to permit a man to work in it. The flushing material is carried through bare rock from the juncture at bedrock to the openings underground. This plan has been used, particularly where a cast-iron surface line is laid upon the surface to carry the flushing material from the breaker to the hole, and down the hole continuously, with no opening to the air at the top of the hole, thereby eliminating the necessity of an attendant at this point (Fig. 3). Another similar type of borehole lining is constructed of hexagonal pieces of vitrified brick (Fig. 4). This type requires a steel drive pipe through the surface wash large enough to provide a finished tube of the desired size surrounded by a brick wall about 4 in. thick. The special bricks are laid in cement, six to a circle, around a lubricated pipe used as a form, and lowered in sections inside the large drive pipe; the bottom section is seated in a socket drilled in the solid rock, having the same inside

Jan 1, 1941

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935