Search Documents

By E. R. Gilbert, D. E. Munson

Creep of copper under 75 to 1.50 kg per sq cm stresses at temperatures near the melting point was found to he a complex reaction controlled by three mechanisms acting in parallel. In order of appearance with decreasing temperature, the auerage activation energies, Qc , are 168, 79, and 24 kcal per mole. Stress dependence of the minimum creep rate was found to he an exponential for the two high-Qc processes and a power law for the low-Qc, process. Transition of control occurs from one mechanism to another. The relative transition temperature depends upon the applied stress, and the range oiler which the transition occurs depends upon the difference in the activation energies of the mechanisms. The creep behavior at high temperature is explained by the climb of dislocations through thermally or mechanically formed jogs, CREEP in pure fcc metals at temperatures in excess of one half the absolute melting point is normally controlled by dislocation c1imb.1,2 A climb model which seems applicable, according to an extensive analysis of data,3 was derived by Weert-man.4 This model assumes jog-saturated dislocations and predicts an activation energy, Qc, nearly equal to that for self-diffusion, USd. Although the requirement of jog saturation is restrictive, agreement between theory and experiment seems adequate. Many other theoretical treatments, including an early model by Mott,5 include detailed consideration of jog formation as an initial requirement for climb. These models predict activation energies for creep which differ from those of self-diffusion. Seeger6,7 postulates an observed activation energy related to the stacking-fault energy. Thus, Usd <Qc<5Usd + Uj where Uj is the jog-formation energy. Seeger incorporated qualitatively the influence of the relative numbers of thermal and athermal jogs. Expanding this concept, Shoeck8 explicitly states a function based on formation mode and relative numbers of vacancies: e r ci exp {-uf/k T} exp {-Um/k T} [ 1 ] where Uf and Um are energies of vacancy formation and migration, respectively. The concentration of jogs, Cj, depends upon the manner of jog production. For intersection jogs, Cj is not sensitive E. R. GILBERT, Junior Member AIME, formerly with De- to temperature; for thermal jogs, Cj is proportional to exp {—Uj /k T}. Schoeck regards each mode as a distinct mechanism; therefore, the mechanisms may act together.299 The diversity predicted by theory, surprisingly, has not been substantiated by experimental results. A significant investigation must include the extremes in stacking-fault energy. Extensive creep studies of aluminum10 and nickel,11,12 high stacking-fault energy metals, have been made. Comparable studies on a low stacking-fault energy metal, such as copper, have not. It is the purpose of this paper to report the results of an investigation of the creep of copper under conditions which favor thermal jogs. EXPERIMENTAL Cylindrical compression creep specimens (0.240 in. in diameter by 0.400 in. long) were machined from cold-drawn rods of electrolytic tough-pitch copper containing 0.0007 Mg, 0.002 Fe, 0.001 Ni, 0.0005 Ag, Cd < 0.005, and Pb < 0.005 wt pct impurities. Undetected spectrographically was a nominal 0.04 wt pct 0, which occurs as a Cu2O constituent distributed discontinuously at grain boundaries. Vacuum annealing at 900°C for 15 min produced a stable 0.03-mm average grain diameter. Testing was carried out using apparatus similar to that described by sherby,13 modified by enclosing platens and a push rod in a vacuum cylinder. Normally this arrangement resulted in pressures less than 10 Only a slight surface tarnish, less than 0.0005 in. in thickness, occurred during the test. The applied stress, corrected for atmospheric pressure, was maintained within 2 pct of the desired true stress by the addition of lead shot at fixed strain increments. Creep strain was measured with dial gages as a relative displacement of the upper and lower platens; accuracy of measurement was 0.0001 in. Two creep-test methods were used, the differential or cyclic temperature14 and the isothermal, to obtain creep data at stress levels of 150, 100, and 75 kg per sq cm over the temperature range of 620° to 1032°C. Minimum creep rates were used from both test methods; this was considered proper because comparable temperature tests or cycling to the same temperature gave the same creep rate, within experimental error. The cold vacuum test chamber, with the unstressed specimen in place, was heated to temperature by placing a preheated furnace over the chamber. Temperature equilibrium was attained within 30 min. For the cyclic tests, the stress was removed during the 5 to 10 min necessary to effect the temperature change and re-

Jan 1, 1965

THE CHAIRMAN (H. W. MORSE, Los Angeles, Cal.).-I would like to open this meeting for a little while to the general subject of leaching. We ought not to hold back if we have any new schemes for the future. I know that those of us who are tangled up with this lei thing work will appreciate any suggestions that will make us work harder and, scheme, harder to pull through these past difficulties on leaching. F. S. SCHIMERKA, Clifton, Ariz.-Under the direction of J. W. Bennie, General Manager of the Shannon Copper Co., Clifton, Ariz., &apos;it has been my valued privilege to cooperate in the elaboration of a hydrometallurgical process aiming at the recovery of copper in mill tailing resulting from a gravity concentration of a low-grade semi-oxidized sulphide ore occurring in a porphyritic gangue. The experimental work which has been carried on with a 25-ton plant is completed, and the company is building at present a leaching plant on a larger scale, the first unit consisting of a 150-ton roasting furnace and accessories for leaching the calcine.

Jan 12, 1916

By Robert Maes, Robert de Strycker

The Cu-Sn-As systeM was studied in the region near the Cu-42 and (214-As binary diagrams, where reactions in the solid state appear, resulting from the decomposition of the y(Cu-Sn) phase and from the formation of the 7 phase (Cu,As). The techniques used were microscopic observation, thermal analysis by dilatometry, and X-vay diffraction. The formation of the 7 phase gives rise to a ternavy pevitectoid veaction; the decomposition of the y phase gives rise to five transitional reactions. The temperatures of almost all these reactions could be determined; in the most favorable cases , the accuracy of this determination was of 11.5-C. The 7 phase is stabilized by tin additions, the arsenic atoms being replaced by tin atoms up to 35 pct; this has allowed the preparation of pure j) phase and the confirmation, by extrapolation, of the conrposition of this compound in the Cu-As diagram. In the first part of this work, the solidification reactions in the Cu-Sn-As phase diagram were studied. In the copper corner, the structure of the alloys presented the evidence of reactions in the solid state: on the one hand, all the alloys containing the y phase of the Cu-Sn diagram showed, under the microscope, that this phase had formed different decomposition products after complete solidification; on the other hand, the appearance of the 7 phase of the Cu-As diagram necessitated the introduction of a peritectoid formation reaction. The study of the decomposition of the y phase has been done by preparing about forty alloys that were homogeneous y at high temperature. The formation of the 7 phase has been studied by means of a few alloys with a composition near the homogeneity field of this phase at room temperature. The part of the Cu-Sn phase diagram of interest for this study is represented by Fig. 1, with the phase designation which will be used in the remainder of this paper; it is drawn after Hansen and Anderko.&apos; The Cu-As diagram has already been presented in Part I of this work; the significant features of this study are the existence of the arsenides CusAs and Cu5Asz, and the formation of a compound CUEAS, designated as the 7 phase, by a peritectoid reaction at about 325°C. EXPERIMENTAL METHODS The fundamental technique for the investigation of this part of the Cu-Sn-As constitution diagram was microscopic observation; the greatest part of the observed alloys has also been subjected to thermal analysis by dilatometry; a few selected alloys have then undergone an X-ray analysis by powder diffraction. Alloy Preparation. The alloys were prepared from the same products as in Part I of this study: cathode copper, arsenic with a purity better than 99.5, and tin with a purity of 99.98. The fusion of the ternary alloys was realized from

Jan 1, 1967

By Quentin D. Singewald, B. S. Butler

Some of the broader relations between structure and ore deposition along the London fault, deduced from a thorough study of the geology of the eastern part of the Mosquito Range, should be of general interest to economic geologists. The first part of this paper is a generalized statement of the geology of the region in which the London fault is located; it may be supplemented by reference to several earlier publications by the writers and to the U. S. Geological Survey&apos;s Professional Paper 148, on the Leadville district. The second part deals with the structure of both the fault and the disturbed zone adjoining the fault. The third part discusses the salient features of the ore deposits, particularly emphasizing structural control. The two generalized maps are complementary to one another but contain too many data to show on a single small map. The London fault is between Leadville and Alma, and the ore deposits along it are said to lie in the Alma district. Field work in this district, during six summers since 1927, has been a part of the cooperative work of the U. S. Geological Survey, the State of Colorado, and the Colorado Metal Mining Board. The writers have made use of work by R. D. Butler, J. W. Vanderwilt and R. E. Landon. G. F. Loughlin and C. H. Behre, Jr., who have worked on the west side of the range, have contributed valuable suggestions. Mining men of the district have aided in many ways. General Geology Pre-Cambrian Rocks.—The oldest rocks in the district are schists, correlated with the Idaho Springs formation of the Front Range. Quartz-mica schist predominates, but other types occur locally; almost everywhere the rocks show considerable lit-par-lit injection. Intrusive into the schists are two varieties of granite, only one of which is widespread. It is a fine-grained, porphyritie, gray granite correlated with the Silver Plume granite of the Front Range. Near the head of Buckskin Gulch a

Jan 1, 1937

By Robert Franke

(Butte Meeting, August, 1915.) IN view of the prominence which the conical mill has attained in the fine-crushing field within the few years since its introduction, the following comparison with its more mature forerunner, the Chilean mill, based on extensive tests, is submitted in the interest of the milling profession. Soon after designing the concentrating plant of the Miami Copper Co. in 1909, the Hardinge conical mill made its appearance in the milling forum. Its possibility as a suitable crushing device for the plant was well recognized, but in view of the lack of commercial demonstration, at the time, as to capacity, efficiency for desired product, and the still more uncertain factors of cost of maintenance and power consumption, it was deemed that the immediate adoption of this machine throughout the plant would be a hazardous undertaking. For these reasons it was decided to equip the majority of the imme diately required units of the plant with Chilean mills, the fine-crushing proficiencies of which were better known, and one section with Hardinge mills, to serve as a test unit for the guidance of future installations and replacements. Thereby, after 1.5 years&apos; operation with both types of mills, a thorough test as to metallurgical efficiency and cost economy has been obtained. The conical mill used in these tests is the 8-ft. Hardinge pebble mill, having a cylinder 22 in. in length. The cylindrical portion of this mill is lined with cast-iron liner plates, and the conical extensions with silex bricks bound together by cement. Each liner plate carries a projecting lifter, the function of which is to increase the height of drop of the lifted material. Danish No. 5 pebbles, obtained from the coast deposits of Denmark, are used for the grinding charge. The Chilean mill used is a fast-running, 3-roller, 6-ft. Saturn mill, with screens of 0.037-in. opening. The feed to these mills is the oversize of Callow screens having 0.029-in. openings, which follow rolls crushing to 0.5 in.

Jan 7, 1913

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

The Development of Research and Quality Control in the Modern Steel Plant. By Leo F. Rein-artz. (Metals Technology, April 1943) Blast Furnace and Raw Materials Essential Considerations in the Design of Blast Furnaces. By A. L. Foell. (,Metals Technology, December 1942) Results Obtained from Surveys of Gas at Furnace Tops. By James M. Stapleton. (Metals Technology, January 1943) Physical Aspects of the Dust Catcher, Gas Washer and Precipitator on No. 3 Furnace at Carrie. By C. P. Clingerman and C. J. FleiscH. (Metals Technology, January 1943) Slag Control by Introduction of Flux through Blast-furnace Tuyeres. By Carl G. Hogberg (Metals Technology, January 1943) The Electrical Conductivity of Molten Blast-furnace Slags. By A. E. MaRtin and GerRard Derge. (Metals Technology, August 1943) Some Physical Characteristics of By-product Coke for Blast Furnaces. By CEarles C. Russell and MichaeL Perch. (Metals Technology, December 19+2) Pyrometry at the Coke Oven. By Robert B. Sosman. (Metals Technology, December 1942) Calcination Rates and Sizing of Blast-furnace Flux. By T. L. Joseph, H. M. Beatty and Gust Ritsianes. (Metals Technology, December 1942) The Low-temperature Gaseous Reduction of a Magnetite. By M. C. Udy and C. H. Lorig. (Metals Technology, October 1942) Steelmaking Problems of Total Operation in Steelmaking. By William C. Marshall and Frank G. Norris. (Metals Technology, April 1943) Silicon-oxygen Equilibria in Liquid Iron, By C. A. ZapFFe and C. E. Sims. (Metals Technology, September 1942) Equilibria of Liquid Iron and Simple Basic and Acid Slags in a Rolating Induction Furnace. By C. R. Taylor and John Chipman. (Metals Technology, September 1942) Rapid Analysis of Oxygen in Molten Iron and Steel. By Gerhard DeRGe. (Metals Technology, January 1943) Silver Chloride as a Medium for Study of Ingot Structures. By Karl L. Fetters and Margaret Dienes. (Metals Technology, August 1943)

Jan 1, 1943

INTRODUCTION Porphyry copper deposits have been reported from the Caribbean area by Pease (1966), Cox, et al. (1973), Guild (1974), Kesler, et al. (1975), and others. This chapter summarizes the most widely known characteristics of those deposits. Only one deposit that conceivably can be classed as a porphyry copper occurrence is in production (Pueblo Viejo, Dominican Republic), but others are known whose tonnage and grade are of economic interest. Deposits in this province may be classified as copper-gold or copper-molybdenum types (Kesler, 1972), but deposits associated with quartz-rich plutons that have high Na2O:K2O and high gold:copper but low molybdenum: copper ratios dominate. Porphyry copper occurrences are reported in the literature from Puerto Rico, Haiti, the Dominican Republic, Jamaica, and Cuba. Only the porphyry copper deposits from Puerto Rico are extensively described in the literature; consequently the Caribbean porphyry copper province in general is not as well documented as the southern Cordilleran orogen. Because past published technical descriptions are incomplete, some data presented here are new to the literature. The Caribbean includes the island arcs between North and South America. Porphyry copper occurrences are known from the Greater Antilles, the generally east-west trending group of islands that lies south of North America. Fig. 48, therefore, only covers the Greater Antilles portion of the Caribbean. Porphyry copper deposits in this area are not described by the Lowell and Guilbert (1970) model in details of metallization (general paucity of molybdenum), alteration (scarcity of orthoclase), or petrography (preponderance of quartz diorite). Therefore, this model should be modified to include deposits associated with quartz-bearing plutons such as those found in the Caribbean. In the Meme deposit on Haiti ore occurs in skarn adjacent to the quartz diorite phase of a composite quartz monzonite-granodio-rite-quartz diorite pluton (Kesler, 1968). This deposit, with a K-Ar 66 m.y. date, is not included in Fig. 48 as a porphyry copper deposit because metallization is restricted largely to the intruded rocks. Although the intrusive rocks at the Meme deposit may contain sulfide near skarn contacts they are otherwise essentially unaltered. Porphyry molybdenum deposits as defined by Clarke (1972) have not been reported in the Caribbean area.

Jan 1, 1978

By P. M. Kelly, E. P. Butler

Four Mn-CLL alloys, containing 60, 70, 80, and 90 pct Mn, respectively, have been examined in the quenched and the quenched and aged conditions using electron microscopy and electron, neutron, and X-ray diffraction. After certain heat treatments the alloys transform from fee to fct and in the tetraom1 condition show a domain structure parallel to {101} planes. Neutron diffraction indicates that the domains are antiferrornagnetically ordered. The domain boundary contrast has been examined using bright- and dark-field microscopy, and the contrast effects observed under favorable conditions have been used to deduce the c axis orientation in each domain. The domains are extremely mobile and can be nucleated at precipitate particles and screw dislocations. The domain mobility is responsible for the high damping capacity. In the aged material a Mn precipitates in the Kurdjumov-Sachs orientation and results of both electron microscopy and neutron diffraction indicate that the matrix separates into two components—one rich in manganese and the other rich in copper. ALLOYS of manganese and copper have the unusual combination of a high damping capacity and good mechanical properties and have been the subject of a number of investigations as part of a general interest in high damping capacity alloys for engineering purposes.&apos;,&apos; SO far, however, there has been no reported electron metallographic study of these alloys. The Mn-Cu system has an extensive range of solid solubility at high temperatures, and the equilibrium phases are expected to be y (fee) and a Mn. The high damping capacity is associated with a metastable tetragonal structure of variable c/a ratio, which forms from the high-temperature y phase. This latter phase becomes more difficult to retain as the manganese content increases, and alloys containing more than 82 wt pct Mn undergo a reversible martensitic fcc — fct transformation on quenching. The X-ray work of Basinski and christian3 showed that the Ms temperature for the transformation was below room temperature for alloys in the range 70 to 82 pct Mn and increased linearly with manganese content. When quenched from the y region, alloys in the range 50 to 82 pct Mn are cubic at room temperature, but become tetragonal if aged at temperatures between 400" and 600°C. The martensite transformation occurs on cooling from the aging temperature. Tetragonal alloys have a banded microstructure and the bands analyze to be traces of (110) planes. Similar microstructures have been observed in In-Tl4 and in other manganese-base systems, such as Mn-Au5 and Mn-Ni.6 The mobility of the bands in Mn-Cu alloys can be demonstrated by optical examination of a polished specimen surface subjected to a cyclic stress.7 The bands appear and disappear as the stress is varied, and X-ray measurements of the (200,020) and (002) peak intensities confirm that a reversible reorientation of the tetragonal structure occurs. Meneghetti and sidhu8 investigated the magnetic structure of Mn-Cu alloys and found antiferromagnetic ordering in furnace-cooled alloys of composition >69 at. pct Mn. Magnetic super lattice reflections occurred at the (110) and (201) positions and the proposed structure was fct with the spins along the c axis. A more complete investigation by Bacon et al.9 confirmed this structure. The magnetic ordering temperature Tn was found to increase linearly with manganese content in the same way as the Ms temperature, and at any composition, Tn > Ms. This relationship suggested that the magnetic ordering was responsible for the cubic — tetragonal transformation in the manganese-rich alloys. The purpose of this investigation was to study the mechanism of high damping and the structural changes that occur on aging. The main technique used was transmission electron microscopy, but X-ray and neutron diffraction experiments were also carried out. EXPERIMENTAL Materials and Heat Treatment. The four alloys, provided by the Admiralty Materials Laboratory. were of nominai composition 60, 70, 80, and 90 Mn and all had low impurity levels, <0.05 pct C, <0.2 pct Fe. This material was cold-rolled to 200-µ strip with intermediate annealing and then given a final heat treatment of 24 hr in the range 800° to 900°C followed by water quenching. An identical heat treatment was given a length of 3/4-in.-diam bar of the 70/30 alloy from which the neutron diffraction specimens were machined. It was suspected that the tetragonal structures would be metastable at room temperature, and so the alloys were not aged until required for experiments. After aging in a salt bath the alloys were water-quenched. Thin Foil Preparation. Initial thinning to 50 to 75 µ was possible in a solution consisting of: 50 ml nitric acid 25 ml acetic acid 25 ml water The surface deposit and grain boundary etching was removed by a final electropolish at around 20 V in an electrolyte consisting of:

Jan 1, 1969

Discussion of the paper of FRANCIS S. PEABODY, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 125, May, 1917, pp. 775 to 781. THE CHAIRMAN (CARL SCHOLZ, Chicago, I11.).-Coal wastage is undoubtedly one of the most prominent topics before the coal operators of the United States today. Even those who have been in the business only 25 years, like myself, know that the exhaustion of coal is something that should and must, be curbed. If it is not, before long we shall discover that the great coal resources of the country are not what we-thought they were; we have been so accustomed to work at the best and thickest coal alone, that it will be difficult for us to realize one of these clays-and that (lay is not far distant-that we are no longer the rich nation in coal that we thought we. were. In this connection I feel obliged to attach a little blame to the Geological Survey for misleading the people. There are several members ,here who assisted in that work, and I am going to ask them to defend themselves. The Geological Survey deals with coal seams of much less thickness than we could now expect to, mine, particularly with the present high wages, excepting at a prohibitive cost. The Geological Survey, in its estimates, does not discriminate between thick and thin seams, but simply estimates our resources at so many hundred thousand billion tons of coal. I believe they include seams from 15 to 18 in thick, but you all know that a vein below 3.5 or 4 ft. is not considered economical to mine at this time. R. V. NORRIS, Wilkes-Barre, Pa.-Mr. Peabody has evidently been thinking almost entirely of Illinois conditions, with which I regret to say I am absolutely unfamiliar. In some West Virginia mines the total recovery at present is considerably over 90 per cent. and extraction-, as high as 97 or 98 per cent. are claimed.

Jan 1, 1918

Discussion of the paper of C. M. YOUNG, presented at the St. Louis meeting, October, 1917, and printed in Bulletin No. 129, September, 1917, pp. 1369 to 1384. CARL SCHOLZ, Chicago, Ill.-Mr. Young was kind enough to&apos; allude to the development of a mine in which I am now engaged. Several months ago the Burlington Railroad decided to open a mine in the field Which they own in Franklin County containing some 15,000 acres .(6070 ha.) of coal, ranging in thickness from 8 to 12 ft. (2 to 3.6 m.). This proposition in itself is attractive to any mining engineer, but with the backing of a large company I saw an opportunity to do some novel work in the construction line, and for several months I have been investigating and working on the problem of developing what I hope will be the largest and best equipped mine in the State of Illinois. The shaft will be sunk at a place where the coal lies at a depth of 600 ft. (182 m.) and conditions both of the surface and of the coal are ideal in every way; the seam is almost level, and we had only 7 ft. (2 m.) of surface clay to go through. We are going to hoist by skips in order to reduce the rope speed. I believe that is a long step in the direction of economy, because we not only double the output of the mine by hoisting the contents of two cars atone time, but we reduce the proportion of dead weight. In our case there will be 20 tons of coal and 18,000 lb. of skip, or 55 per cent. net and 45 per cent. tare. That, of course, necessitates less than half the rope speed for the same tonnage, and we all know that speed means power and power means cost. Skip hoisting permits the use of solid-end gate cars, which is an advantage. The cost of these cars will be in the neighborhood of $250 apiece; They are well built, with roller-bearing wheels of the most up-to-date type, spring draw-bars, and refinements of-that character which are necessary to move the loads most advantageously.

Jan 1, 1918

By J. L. Wyatt

The electrical resistance of titanium as a function of purity and temperature was measured from —325" to 2800°F. Two points of inflection in the data plots were found, and an increase in resistance with increase in temperature above the transformation was observed. IN 1948 Greiner and Ellis&apos; reported on the thermal and electrical properties of titanium, including a study of the effect of temperature on the electrical resistance. The materials used in the research were obtained from the United States Bureau of Mines, where powder metallurgy techniques were being employed for consolidation purposes. These authors found a decreasing resistance with increasing temperature above 1625°F, and concluded that the latter temperature represented the point of transformation from hexagonal close-packed to body-centered cubic structure on heating. They reported a specific resistivity value of 55x10-6 ohm-cm, and showed that dp/dt was positive, decreasing with increasing temperature above ambient. In one of his early texts Hume-Rothery2 mentioned that certain metals, including titanium, exhibited minima in plots of resistance vs temperature. He indicated that this occurred at 212°F. Reporting many years ago on the effect of temperature on the electrical resistance of zirconium, de Boer and Fast³ showed that phase transformation in this sister metal occurred over a range of temperatures, the extent varying with its purity. Graphs of resistance vs temperature, showing transformation effects over a range of several hundred degrees, were presented for relatively impure metal. In the latter case the resistance decreased with increasing temperature throughout the region of partial phase transformation, thereafter increasing as predicted for normal metals by modern theories of the solid state. Since the quality of metal used in previous studies was substandard compared with iodide-type titanium, and in view of the fact that there seemed to be some rather unusual observations in the reported literature, it was decided to undertake a more extensive study of the thermal effects using high purity titanium, and to include temperature ranges beyond those which had been studied in order to ascertain whether or not the characteristics of zirconium would be duplicated. Experimental Materials Materials used in this investigation included commercial quality titanium (Ti-75A produced by the Titanium Metals Corp. of America) in the form of ¼ in. diam rods, and high purity iodide titanium (produced by the Foote Mineral Co.) in the form of crystal bar of irregular size. The latter was cold-swaged into rod form and machined to the desired size. Lead wires to all specimens consisted of 18 gage Ti-75A. Chemical analyses of the stock materials are given in Table I. Experimental Procedures Specimens 2½ to 3 in. in length were prepared with diameters nominally 0.15 to 0.20 in. Two holes,

Jan 1, 1954

By W. S. Ayres

I AM well aware that this subject is not strictly in the line of mining engineering, yet as it is a subject with which mining engineers at times have something to do, I have thought, perhaps, it might not be wholly out of place to communicate to the Institute something of the method used in determining deflection, and of its final issue. Having felt a need of some simple formula for determining the deflection of girders of uniform cross-section under any load, I have been led through the counsel of Mr. Frederick J. Slade, to whom I am indebted for many suggestions, to undertake a labor of which I shall in this paper give only some of the most important features. The results arrived at agree with those obtainable from the received formula; of Weisbach, Rankine, and others, but the expressions given by these authors, and by all others that I have at hand, are of such a form that they are not easily applied by those whose higher mathematics have become rusty from disuse, and they require, moreover, too much labor in their application to be of practical value. The general formula that I have adopted is similar to that given by Rankine, and is deflection = [mWl3 -El], in which l is the span, W the total load, E the modulus of elasticity, I the moment of inertia of the uniform cross-section of the girder, and m a factor depending for its value on the mode of distribution of the load. The problem then is to find the value of this factor m in the formula, and for some distributions of the load it leads to a number of mathematical difficulties. In this place I shall consider first the girder to be loaded symmet-

Jan 1, 1877

By Robert A. Cook

In the increasing struggle to cheapen the cost of our iron and steel products a great deal of attention lias been given to economies in the manufacture of coke; and while but little lias been accomplished in this direction in the United States, the narrow margin between cost and market-price, which has obtained here for the past few years of continuing manufactur ing depression, has brought the coke-maker face to face with the problem, how to save, and benefit by it, the hitherto waste products of distillation. I These may be summed up under three heads, generally rank ing, in value, in the following order: 1. Ammonia salts.. 2. Oil- or tar-products. 3. Gas. There are cases in which the last may assume the position of greatest importance. The greatest obstacle encountered by the American coke maker, on investigating the subject, has been the apparent necessity of discarding his existing plant of bee-hive ovens, and erecting an entirely new and very expensive system of retort ovens, against the product of which Be has probably been prejudiced from his earliest knowledge of the subject. The object of this paper is to bring prominently before our coke-experts a brief history of the development at Sheffield, England, of a most successful system of the utilization of by products in connection with all already existing plant of bee hive ovens. This system has now been in satisfactory operation for about five years, and is applied to a series of blocks of ovens, comprising-about 140- in all At this plant, belonging to the well-known firm of Newton,

Jan 1, 1897

INTRODUCTION The after-tax rate of return that properly discounts future cash flows is usually referred to as the "discounted cash flow-rate of return" (DCF-ROR). The method is also referred to as the internal rate of return, true rate of return, and investor&apos;s rate of return in some literature. According to Stermole (1974, p. 188) industry polls indicate that the DCF- ROR method is the number one economic evaluation decision method used by more than 90% of the industrial companies that use for- mal economic evaluation procedures. Other economic evaluation methods that have been used in the past, such as payback period, accounting ROR, etc., have largely given way to DCF-ROR analysis because they fail to account properly for the time value of money. DCF-ROR is generally defined as that rate of return that makes the present worth of future generated cash flow over the life of the project (including after tax salvage value) equal to the present worth of all after-tax investments. The "present worthing" of future cash flow involves discounting future cash flow to a present value according to the mathematics of compound interest at some interest rate. The determination of the interest rate that equates the present worth of future after-tax earnings with the present worth of all after-tax investments necessary to create such earnings is properly called the discounted cash flow rate of return analysis. Although present worth calculations are usually used for determining the DCF-ROR, the same results can be obtained by comparing income and costs of any equivalent point in time, i.e., future worth, etc.

Jan 1, 1980

By S. C. Das. Gupta, B. S. Lement

isothermal formation of martensite occurs in the range of —65o to —197oC and is always preceded by some athermal transformation. By rapid cooling the isothermal, but not the athermal, component of transformation can be suppressed. Stabilization against isothermal transformation can be induced by cycling from below M. to room temperature. A LTHOUGH the transformation of austenite to XV martensite is generally believed to occur only on cooling, recent evidence indicates that this reaction can also occur at constant temperature. Isothermal formation of martensite was observed in tool steel by Fletcher, Averbach, and Cohen.&apos;. They found that the hardening reaction that occurs during the quenching of a plain carbon or low carbon alloy tool steel does not stop immediately when room temperature is reached; instead austenite continues S. C. DAS GUPTA is Research Fellow, Department of Metallurgy, University of Notre Dame, Notre Dame, Ind. B. S. LEMENT, Associate Member AIME, is on the Research Staff, Department of Metallurgy, Massachusetts Institute of Technology, Cambridge, Mass. Discussion on this paper, TP 3123E, may be sent, 2 copies, to AIME by Dec. 1, 1951. Manuscript, April 16, 1951. Detroit Meeting, October 1951. This paper represents part of a thesis by S. C. Das Gupta submitted in partial fulfillment of requirements for the degree of Doctor of Philosophy in Metallurgy to the University of Notre Dame. to transform at room temperature although at a decreasing rate. Since only a small amount of austenite transforms in this fashion, isothermal formation of martensite was considered to be merely a "tailing off" effect of the main hardening reaction. Another point of view was advanced by Kurd-jumov and Maksimova"&apos; * who reported that the austenite-martensite reaction could be suppressed by rapid cooling of a 6 pct Mn-0.6 pct C steel in liquid nitrogen and that as much as 25 pct martensite could be formed by reheating to and holding at subzero temperatures above that of liquid nitrogen. These investigators came to the conclusion that martensite is thermally nucleated at certain special regions in the austenite and subsequently grows to observable dimensions. Isothermal transformation of austenite to martensite was cited by Fisher, Hollomon, and Turnbull" as evidence supporting another nucleation and growth theory of martensite formation. According

Jan 1, 1952

By Alfred Weiss

Daniel C. Jackling&apos;s innovative concept for handling low grade ores ushered in a new philosophy of open pit mining. As one of the greatest minemakers of all times he revolutionized major segments of the industry and helped strengthen US defense efforts during World Wars I and II by making possible the tremendous copper supplies from US mines. Many great mining men have since followed in his footsteps with their discoveries of new orebodies or development of new mines. Their brilliance in leadership can also be traced to the coupling of a new idea to the physical nature of the materials in the earth&apos;s crust or to the extractive stages of minerals recovery. The minerals industry is now in another era of change and must again devise techniques to meet the challenge. The task is not only to create new exploration techniques and develop new mining methods, but, I believe, to optimally apply new concepts and tools in daily decision-making.

Jan 11, 1978

By Paul Beck

IT is well known that the hardness of metallic single crystals, like that of polycrystalline metals, increases during deformation (hardening by cold-work). It is also known that, as a consequence of deformation, the metallic material acquires an evident thermodynamic instability, revealed, for example, by the fact that the increased hardness gradually decreases with time, especially at elevated temperatures (softening by annealing). The temperature at which the stabilizing process begins is different for various metals, and for any metal it depends on the amount of deformation. Such stabilization of deformed metals may proceed in two different ways: through recovery, and through recrystallization. The former process allows the unstable deformed metal body to approach stability gradually and without visible change in the grain structure; the latter process, like an allotropic transformation, yields directly the undeformed stable "phase" in the form of new undeformed crystals, which, starting out of a certain number of nuclei, grow into and&apos; consume&apos; the deformed hard material. The extent of stability attainable through recovery is limited, espe-cially if the deformation of the metal crystal or crystals involves not only the gliding along slip planes, but also the bending of the slip lamellae, or at any rate the bending of comparatively large parts of the crystal lattice. In such cases, for instance in bent single crystals or poly-crystalline metals subjected to any deformation, recovery will not as a rule be able to restore the "straight" undeformed lattice, and stability can be attained only by recrystallization; that is, by the consumption of the bent crystal lattice parts by new, undeformed crystals-a much more drastic process. It is evident that the part of the surplus free energy stored in deformed crystals, which is present in the form of the elastic energy of the bent lamellae, is in these instances not considerably involved

Jan 1, 1937

By Clemens Jones

The peculiar property of the lode-stone has been known for many centuries. It was very early observed that, by contact with it, iron is magnetized; and it is needless to dwell here upon the history allied to this discovery, now constituting the wonderful science of magnetism. Deposits of magnetic ore are distributed all over the world. The ore is sometimes very rich and comparatively free from gangue, sometimes sparsely disseminated in the native rock. These bodies of lean ore often cover large areas. Modern ingenuity has utilized the principle of the magrtet, originally derived from the ore itself, and really belonging to the time of Plato and Theophrastus, to separate the magnetic ore-particles from the rock which has previously been crushed. This process recovers the ore in the state of a concentrate very rich in iron and, in some cases, desirable for Bessemer purposes. The magnetic separator is no longer a novelty. It was only at the last meeting of the Institute in New York, that Messrs. Birkinbine and Edison (Trans., xvii., 728) and Mr. Robert Cook (Ib., 599) described some of&apos; the principal designs of apparatus in use. E. S. Dana classifies the natural magnetic minerals in the following order: magnetite, pyrrhotite, franklinite, almandite and minerals " containing considerable FeO." Of these, ferroso-ferric oxide, or magnetite, is the type. The proportionate amount of ferrous oxide essential to magnetize the compound, is not established. Ferrous oxide appears to be the only magnetic oxide of iron. Tissandier (Compt. Rend., lxxiv., 531) produced ferrous oxide in the anhydrous state, by the action of carbon dioxide on pure iron at a red heat, according to the equation : Fe + CO2 = FeO + CO. This is black, crystalline and magnetic. Heated to redness in the air, it is converted into Fe3O4. Sidot (Compt. Rend., lxvii., 175) has also produced an oxide exhibiting magnetic polarity, by heating ferric oxide to a temperature

Jan 1, 1891

By Samuel S. Wyer

THE following description of methods for conducting gas-producer tests is probably the first attempt to give the subject an analytical, thorough and comprehensive treatment. In some cases where tests have been made, the methods have been so unsystematic and ambiguous that it has been impossible to secure comparable results. To eliminate this difficulty, the following provisional code of gas-producer tests-which has some resemblance to the code of boiler-trials of the American Society of Mechanical Engineers-has been developed. The primary object in testing a gas-producer is to determine whether the producer is working satisfactorily or, what is the same. thing, to see if the efficiency is as high as it should be with the type of producer in question, and also to find out if the composition of the resulting gas is adapted to the work it has to do. In order that the test shall be of any value, it must be thorough and comprehensive, and must be conducted with skill and care. When so conducted, the test will reveal the economy of the producer; and, by making suitable changes, the efficiency will often be increased very much. As a result of the tests made by Jenkins, 1 the efficiency was raised from 56.2 to 71.2 per cent. This shows the large saving that may frequently be made in the fuel-consumption by studying the results of a careful test.. The log of the test, given in Fig. 1, shows that, just as soon as the temperature became regular, the percentage of CO, decreased and that of CO increased.

Mar 1, 1905