Search Documents

By Kenneth C. Vincent, A. M. Gaudin

In a study1 of the action of amyl xan-thate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form I then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleach-able xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete mono-molecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene so1ution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A 'splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral—a phenomenon that was totally unexpected yet remains interesting and perhaps important. Method of Radioactive Spies The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by pollard and Davidson.3 The method was first developed by van Hevesy and paneth in 1013, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method, A fundamental tenet of the method is that a radioactive atom and a nonradio-active atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1947

By J. M. Mutmansky, Y. J. Wang, H. L. Hartman

Procedures for determining the operating point that results when a fan is connected to a mine and placed in operation have been a source of confusion for decades. A variety of techniques have been proposed, often to the detriment of the practicing ventilation engineer trying to apply the techniques to the many mine/fan matching problems encountered in the engineering of mine ventilation systems. This paper proposes some different assumptions and definitions that simplify the problems in determining the operating point. As a result, a set of procedures is provided for determining the operating point of a mine/fan system when the outlet areas of the mine and fan are known. To simplify the development of procedures for determining the operating point for a mine/fan combination, the authors suggest that the mine pressures be redefined and then used in such a manner that the conservation of energy is ensured. This provides the basis for the recommendation that the fan operating point be determined using the fan total pressure and the system total pressure characteristics. This procedure can be applied to fans in the blower, booster, and exhaust positions equally well, and to both single-fan and multiple-fan networks. Another advantage is that the method is applicable to fans with or without an evase.

Jan 1, 1986

By Rudolf Gahl

Some time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanners in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but varying the adjustments of the vanner from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 28 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Jan 1, 1910

By D. E. Swets, R. C. Frank

It is well known that hydrogen is introduced into iron or steel as a result of many chemical processes (acid pickling, electrolytic cleaning, plating, etc.). One of the reactions that has been of recent interest1 is the reaction between an iron surface and water vapor. It was shown a few years ago2-4 that hydrogen can be introduced into steel at an accelerated rate during abrasion as a result of this reaction. Grun-berg and Scott have also observed that water in mineral oil lubricants increases pitting failure in ball bearings5 and they have suggested that hydrogen from the water is the primary cause of this effect.' In this laboratory, the question was raised as to whether or not hydrogen is also introduced into the metal surface of a bearing as a result of the decomposition of the hydrocarbon lubricant itself, and an experiment was performed to try to find a satisfactory answer. All steel parts contain some residual hydrogen. Therefore, it appeared that the best way to carry out this experiment without the need for highly accurate quantitative analyses was to use deuterium as a tracer. The natural abundance of deuterium in H2 is only 0.015 pct. The tracer was obtained in the form of deuteroparaffin (CD,(CDJ, CD,) and 0.25 g were dissolved in 20 cc of mineral oil to form the lubricant to be used in the tests. The bearings used were New Departure Type QOLOO ball bearings with a ball diam of 0.187 in. Prior to adding the mineral oil-deuteroparaffin lubricant, the bearings were cleaned in warm trichloroethylene to remove the packing grease. After packing with the new deuterated lubricant, the bearings were operated in a bearing fatigue test machine under a radial load of 190 lb and a thrust load of 190 lb at a speed of 3800 rpm. The expected life under these conditions is about 500 hr. Two tests were made; one for a period of 27 hr and the other for a period of 102 hr. The bearings achieved a temperature of 120o F during the tests. When the tests were stopped the balls were mechanically removed from the bearings and were immediately placed in liquid nitrogen to reduce degassing until the analysis for deuterium could be made. Before analyzing, the balls were warmed to room temperature and scrubbed with several degreasing agents to remove all traces of the deuteroparaffin mixture. This cleaning procedure was shown to be satisfactory by running a control test in which one ball bearing was subjected to all parts of the test except running in the fatigue machine. The hydrogen and deuterium were removed from the balls using a hot extraction apparatus attached to a mass spectrometer. Four balls from each bearing were analyzed. Each one was analyzed separately by removing it from a cold storage volume of the hot extraction apparatus and transferring it to the oven tube with a magnet. As the gases were evolved they were analyzed with the mass spectrometer. Since the hydrogen and deuterium pass through steel in the atomic form and since there are many more hydrogen atoms than deuterium atoms in the sample, the probability of forming an HD molecule is greater than forming a D2 molecule. For this reason the evolution of HD and H was followed as each ball was placed in the oven. The results showed that as each ball from the test bearing was dropped into the oven, the mass spectrometer recording of the HD evolution increased by about ten divisions. When balls from the control test bearing were dropped into the oven, the increase was about one division or less. The hydrocarbon background in the mass spectrometer was also monitored to see if hydrocarbons or deuterocarbons were given off when the balls were dropped into the oven, but no change in the hydrocarbon peaks was observed. Since the balls contained a fair amount of residual hydrogen, isotope ratio measurements were made on the gas obtained from each ball. The D/H value found for those balls which had been operated in the fatigue testing machine was consistently about 0.3

Jan 1, 1962

By W. Rostoker, R. P. Elliott, B. W. Levincer

Phase equilibria in the Ti-Cr-Mo system have been investigated for alloys containing 100 to 40 pct Ti in the temperature range 550° to 1300°C. Five experimental isothermal sections and a surface of incipient melting are presented in addition to a summary projection of the space. Seven vertical sections have been constructed from the isothermal sections. A STUDY of the system Ti-Cr-Mo was undertaken as part of a program sponsored by Watertown Arsenal toward the development of titanium-base phase equilibrium diagrams of potential technical importance to alloy development. The scope of the investigation included the composition range contained by the titanium corner and the line of 64 pct Ti (all compositions are by weight) and the temperature range 550" to 1100°C. A surface of incipient melting was constructed from measurements on a large number of alloys. The system Ti-Cr has been established.&apos;-? The phase diagram is characterized by a wide miscibility field of the solid solution at elevated temperatures and a eutectoid reaction of the type: (15 pct Cr) + TiCr, (685C). The a solid solution has a very limited capacity for solution of chromium (< 0.5 pct Cr). The intermediate phase TiCr2 has at best a very narrow composition range. It has been shown that two allotropic modifications of this phase exist. However, this behavior does not appear to be perceptibly reflected in the form of phase boundaries of the type + TiCr,. In the system Ti-Mo,9-10 the phase is stabilized to successively lower temperatures with increasing molybdenum content. There are no known intermediate phases. The a solid solution is limited to less than 0.5 pct Mo. Because of the very extensive range of the phase, the ternary system was ideally suited to the determination of the phase boundaries by the parametric method of Andersen and Jette." A parametric surface was constructed to provide the necessary basis for the application of this method. Preparation and Treatment of Alloys More than 60 alloy compositions were prepared for the study of this system. Alloy buttons of 10 grams were arc-melted in a nonconsumable electrode furnace using inert atmosphere protection and a water-cooled copper crucible. The construction and operation of this type of melting unit have been adequately described elsewhere.&apos;&apos; To insure complete solution of alloy additions, the buttons were remelted alternately on top or bottom as many as five times. This was accomplished by a suitable mechanism for "flipping" over the ingots. Iodide titanium (99.97 pct Ti) was used as the alloy base. An especially high quality chromium (99.9 pct Cr) was obtained from the National Research Corp. Molybdenum sheet (0.005 in.) of 99.9 pct purity was used.

Jan 1, 1954

By F. S. Young, K. E. Gray

Drilling tests with a 11/4-in. diameter roller bit were performed on Berea and Bandera sandstones and Leuders limestone using water and two conventional drilling muds as circulating fluids to evaluate the influence of dynamic filtration on penetration rate. The muds possessed widely differing API fluid-loss properties. Mud filtrate was constrained to flow beneath the bit; no filtrate flowed radially through the borehole wall. Rock pore pressure at three different locations ahead of the bit, cumulative filtrate volume, borehole pressure and bit location were monitored during drilling. The rock samples, cored in three orientations with respect to bedding planes, possessed a wide range of liquid permeabilities. and were drilled at borehole-to-formation pressure differentials of 0, 250, 500 and 1,000 psig. The effect on penetration rate of API fluid loss, borehole pressure and rock permeability was studied. Rock permeability damage and pore pressure gradients beneath the bit were evaluated. The importance of borehole-to-formation pressure differential was illustrated for each drilling fluid and rock permeability combination. Penetration rates decreased with increased borehole pressure and reduced fluid loss. The observed penetration rate reduction due to changing fluid Ioss was attributed to decreased filtrate flow and improved mud cake plastering hy the low fluid-loss mud. The reduction in filtrate flow could not be related to spurt-loss phenomena. Rock permeability influences penetration rate through particle invasion ahead of the hit, which damage leads to high pressure gradients. Penetration rate variance with sample orientation was evident for water-drZled samples but less obvious for mud-drilled rocks. Permeability damage beneath the bit ranged from 1 to 3 cm. Maximum damage occurred in the first 0.1 cm. Pressure gradients varied with API fluid 10.s.s and could be correlated with penetration rate. The pressure gradient was found to influence penetration rare in rocks of all permeabilities tested. INTRODUCTION Early microbit and small-scale drilling experiments proved to be invaluable contributions to understanding the mechanics of drilling at depth. For example, the effect of borehole-to-pore pressure differential on drilling rate was demonstrated conclusively by Murray and Cunningham&apos;, Eckel&apos; and others .&apos; However, the effects of various drilling fluid properties on drilling rate, particularly filtration, have not been studied extensively on a laboratory basis. Microbit correlations of penetration rate with different viscosity and API fluid-loss muds led EckelV o conclude that viscosity and density. more than API fluid loss, were the most important fluid properties in controlling drill bit penetration rates. Ferguson and Klotz6 studied filtration beneath the bit and stated that the maximum amount of filtrate which could conceivably flow beneath a drilling bit could be described by a potential function associated with flow from a moving disc source. and be characterized by a depth-of-filtrate invasion. Invasion depth is a function of penetration rate, formation porosity and permeability, flooding efficiency, pressure difference between borehole and formation and borehole radius, assuming that no filtrate flows through the borehole walls. Electric analog and experimental measurements were obtained, assuming no plugging of the formation pores. Theoretically, filtrate invasion was predicted to extend from 1- to 15-hole radii beneath the cutting surface; experimental results indicated that the extent of invasion was only Y2 in. Comparing these data with results of core-plugging experiments by Norwak and Krueger&apos; led Ferguson and Klotz to state that the drilling operation apparently contributes to higher filtration rates than are observed in nondrilling core filtration tests in which the core face is jetted and scraped. Glenn and Slusser: in describing a linear filtering system in which a rotating bit continuously scraped mud cake from the surface but did not penetrate Alundum cores, stated that mud-solids invasion and permeability damage of the cores were most severe in the first 2 to 3 cm. The filtrate flow rate through the core was found to stabilize after sufficient time had elapsed for the formation of an internal mud cake whose effective permeability was estimated to be 50 to 300 times as high as that of bulk filter cake. Krueger and Vogel reported core permeability damage depths up to 12 in. during a 5-day exposure period in which filter cake buildup was prevented. Havenaar pointed out that the discrepancy between reported and calculated values of filtrate volume obtained in the experiments of Ferguson and Klotz was due, among other things, to failure of the reported API fluid loss to truly represent filtration beneath the bit. Williams," Pro-koplz and others"" have shown that dynamic filtration tests (where a flow of fluid parallel to the filter surface continually erodes the deposited filter cake until a dynamic equilibrium between wall-shearing forces and normally directed compaction forces is attained) yield higher filtration rates than do static tests. Cunningham and Goinss reported results of drilling tests in impermeable shales. They found that by reducing

By W. H. Emmons

This paper is the third of a series treating of the relations of ores of the metals to igneous rocks. The first&apos; outlined the general problem; the second2 proposed a classification of lode ores, and showed how the distribution of the deposits is in a certain measure controlled by the contour of the roof of the parent batholith. A number of mining districts were discussed, the examples being selected chiefly from group 2 of the classification. The proposed classification of lode deposits, briefly stated, is as follows: 1. Cryptobatholithic: near hidden batholiths which have not yet been exhumed by erosion. 2. Acrobatholithic: in and near cupolas or domes of batholiths—the high points of larger underlying masses. 3. Epibatholithic: on batholiths, near their rims, but below eroded cupolas, or below the highest points of the roofs. 4. Embatholithic: among closely-spaced outcrops which probably are parts of a single bathohth. The outcrops of invaded rocks predominate. 5. Endobatholithic. in and near roof pendants of large batholiths. The invading rocks predominate. 6. Hypobatholithic: in deeply-eroded batholiths, where even roof pendants have been eroded. Deposits of certain metals on the roofs of the batholiths are much more numerous in some positions than deposits of other metals, and the horizontal zonal arrangements of lodes of different metals are shown characteristically only in certain groups. In a large measure, also, the character of the fracturing and metallization is determined by the position on the roof of the batholith. The disseminated copper ores in porphyry constitute a clearly-defined type. All the deposits of these ores, as far as known, are in group 2. They appear to have been formed only in and around small upward projections of the parent granitic masses, and not low on the walls of the

Jan 1, 1927

By Ken-ichi Hirano, B. L. Averbach, Morris Cohen, N. Ujiiye

The influence of plastic deformation in compression on the self-diffisivity of a iron has been measured in the temperature range of 742º to 885°C. The diffusivity is enhanced in proportion to the strain rate, but this dependence decreases with increasing temperature. The magnitude of the strain is relatively unimportant in this connection. Strain rates from 0 to -2 x 10-3 sec-1 were investigated, with a corresponding increase in diffusivity up to 3 x 103 times. The results are analyzed in terms of vacancy diffusion and the excess vacancies introduced during dejornzntion. It is concluded that grain boundaries are the main vacancy sinks in polycrystalline iron and that the vacancy lifetime is therefore dependent on the grain size. A typical vacancy lifetime at 800°C with a nzean grain-boundary intercept of 0.3 cm is of the order of 1 sec. LATTICE imperfections are considered to be the dominant mechanism of diffusion in close-packed crystals. Vacant lattice sites are usually the most important defect, but the enhancement of diffusion along grain boundaries and other short-circuiting paths has been well documented. Inasmuch as plastic straining produces a variety of defects, it would be expected that the application of stresses sufficient to cause plastic flow during a diffusion run might result in an increase in the self-diffusivity. Enhanced self-diffusion in a iron under compressive creep has been observed by Buffington and Cohen&apos; and subsequent coworkers.2 Lee and Maddin3,4 have also found an enhancement in the self-diffusivity of silver single crystals undergoing torsional deformation. On the other hand, Darby, Tomizuka, and Balluffi5 have not observed any significant diffusion increase in single crystals of silver deformed either in tension or in compression, although the results in this case may have been affected by the occurrence of recrystallization. With poly crystalline silver, however, Forestieri and Girifalco6 have found en- hanced diffusion during compressive creep. A small decrease in the self-diffusivity of zinc single crystals under compressive loading has been reported,7 but the applied stresses in these experiments were too low to cause appreciable plastic deformation. For the cases in which enhanced diffusion has been found, a number of common effects have been noted. Usually, the ratio of the diffusivity during straining, Ds, to the diffusivity in the unstrained condition, D,, varies linearly with the strain rate, and does not seem to be a function of the plastic strain, at least up to ? = 0.2. Values of Ds/Du of the order of 100 have been reported&apos;-4 but the enhancement decreases with increasing diffusion temperature. The activation energy for diffusion decreases markedly with increasing strain rate and approaches a level of roughly one-half the unstrained value. Most of the current explanations of these observations assume that excess vacancies are generated by the deformation, but rather large concentrations of excess vacancies and/or long lifetimes are required by these theories.&apos;,&apos;,&apos;,&apos; Since the original work on iron, there has been an important improvement in the compressive-loading technique.2 The early data were also analyzed without taking into account the motion of the coordinate system in the specimens undergoing plastic deformation. This problem has now been solved by a number of investigators (see Refs. 11, 12, and the appendix of the present paper). Consequently, the strain-diffusion runs on iron for the Ds measurements were repeated and extended over wider ranges of temperature and strain rate. In addition, the original diffusivity data9 on the unstrained iron have been corrected for the divergence of the beam in the counting system and new data points have been added, resulting in somewhat different values for the self-diffusi-vities in a iron.10 The new values for Du are used in this paper. A comparison of Ds and Du confirms the large enhancement in the self-diffusivity of iron during compressive creep, as previously reported.&apos;,2

Jan 1, 1963

By Clarence P. Linville

A previous article1 by the authors contained a general description of the new roasting furnace herein described but it did not go into detail as to the metallurgical behavior or the results obtained. Believing that such information would be of great value, they have elaborated on the subject and have given many unpublished details. The furnace described applies the principle of roasting finely divided zinc-sulfide ores, now produced in large quantity by the flotation process, in gaseous suspension; that is, the ore particles are carried, in suspension, in a current of air and gaseous products of the roast. The relatively great fineness of flotation concentrate presents difficulties and problems of roasting in furnaces of the ordinary type; the fine ore is forwarded through the furnace in the form of a shallow bed and its very fineness leads to dense impervious bedding which prevents oxygen from reaching the interior of the bed, thus unduly lengthening the time of roasting and preventing the elimination of the last of the sulfur. The fineness of the concentrate, normally, should lead to a rapid and complete roast, for the speed of roasting is a function of the surface exposed to oxygen, which surface is greatest, per unit of weight, in very fine material. The difficulty in bed roasting is to get the oxygen to the particle. If the fine ore, during the roasting, could be freely suspended in oxidizing gases, full advantage could be taken of the great surface conferred by its fineness. This fundamental idea, of course, is not new, for the Stedtefelt furnace, familiar to the older metallurgists, is an example of it; but the manner in which this is accomplished may be new. The numerous efforts to roast in gaseous suspension show that the idea is attractive; in fact, an analysis would indicate that it is the most reason-

Jan 1, 1925

By T. R. Scott

The acid pressure leaching of zinc-lead flotation concentrates from the McArthur River deposit, Northern Territory, Australia, has been studied in a three-stage, continuous, co-current system, using titanium reactors of 6 gal capacity. The starting pulp contained 2.7 lb solids per gal of synthetic spent electrolyte and the final liquors contained 120-125 gpl Zn. Parameters investigated included temperature (95-120°C), oxygen pressure (30-100 psi), acid addition (80-130% of theoretical), and leaching time (35-65 min per stage). Technical factors studied included mixing and pumping of feed, agitation, settling and washing and control mechanisms. The chemistry of liquor impurities, of scale formation in autoclaves and of lead jarosites in residues was studied in some detail. Results indicated that 90-93% zinc recovery could be obtained with a "low- acid" process, using 113°C and 70 psig with oxygen as the favored operating conditions. Residues contained 16-18% elemental sulphur and 15% lead, together with unreacted pyrite and gangue minerals. Pelletizing of residues was impracticable, and alternative suggestions for the recovery of lead, sulphur and silver are discussed. Preliminary estimates for plant and operating costs are given and enable some comparison to be made with conventional procedures.

Jan 1, 1973

By I. H. Warren, E. Devuyst

A review of the physical and chemical aspects of the direct leaching of metal oxides has been given and com- pared to recent data of the authors and co-workers. The physical aspects, including the anisotropy of the dissolution, the hydration and the zero point of charge of some metal oxides are discussed first and then the kinetics of the dissolution of metal oxides are considered. A general mechanism of the leaching of oxides which describes most of the observed results is proposed.

Jan 1, 1973

By L. Dr. Edeleanu

CRUDE petroleum is a mixture of various groups of hydrocarbons and some bodies containing oxygen or sulphur. These constituents possess properties differing considerably one from another and the proportion in which they are contained in the crude oils is also very different. Owing to this complicated composition the practical use of crude petroleum is much restricted. For example it is sometimes used as a liquid fuel. But its employment in this way is uneconomical because various valuable qualities of the individual constituents are not made use of. The rational utilization of petroleum can only be accomplished if the various groups of hydrocarbons are separated. The mixture of hydro-carbons present in the crude oil must be split up in such a way that the hydrocarbons are divided into various groups having certain predominant characteristics and uses. To accomplish such a separation is the aim of the technical refining of petroleum. ORDINARY REFINING BY DISTILLATION AND CHEMICAL TREATMENT Hitherto this has been accomplished by two processes, namely, fractional distillation and chemical treatment of the distillates obtained. Distillation Process The process of distillation consists in the separation of the constituents of petroleum into various fractions, the boiling points of which lie within certain defined limits. The fractions so separated possess certain special qualities in common, which enable them to be applied for specific purposes in practice. For example, we have the fractions known as benzene, illuminating oils, heavy oils, lubricating oils, etc.

Jan 9, 1914

By A. H. Geisler, R. F. Mehl, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943

By R. F. Mehl, A. H. Geisler, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943

The following is an incomplete list of members and guests who called at Institute headquarters during. the period Mar. 10, 1919,. to Apr. 10, 1919. F. T. Agthe, Hannibal, Mo. Jay Lonergan,. Denver, Colo. W. F. Almy, Canada. R. R. London, Cebu, P. I. P. G. Bandy, Mexico. W. D. Mainwaring, Philadelphia, Pa. H. R. Bank, Humboldt, Ariz. _ W. G. Mitchell, Montreal, Can. Alan M. Bateman, New Haven, Conn. Francis Nicholson, Joplin, Mo. C. A. Brooks, Lead, S. Dak: C. H. Palmer, Los Angeles, Calif. Louis J. Brunel, Oakland, Calif. D. A. Powell, Columbus, Ohio. W. Burns, Sante Fe, N. M. W. H. Reber, Dallas, Tex. J. B. Carlock, Major, 1st Gas Regt. Capt. J. B. Richards, Spokane, Wash. Louis S. Cates, Hayden, Ariz. T. C. Roberts, E. Orange, N. J. W. M. Corse, Mansfield, Ohio Max Roesler, Washington, D. C. E. 0. Daue, Philadelphia, Pa. C. 0. Sanford, Los-Angeles, Calif. John Davenport, W. Norfolk, Va. Gustave Sessinghaus, Denver, Colo. James T. Dixon, London, England, . E. H. Shriver, Milford Center, Ohio. S. K. Dahl, Messina, Transvaal, S. Af. H. M. Spoor. W. G. Eberhardt, Tucson, Ariz. W. H. Staver, New York. H. S. Emlaw, Grant Haven, Mich. D. B. Sterrett, Washington, D. C. I. W. Farrand, Camp Merritt. W. G. Swart, Duluth, Minn. Oscar Gotsch, Jr., St. Louis, Mo. A. W. Stickney, London, England. James 0. Greenan, Oakland, Calif. E. C. Templeton, Downey, Calif. Gilbert Hart, Philadelphia, Pa. . . R. T. Walker, Pioche, Nev. K. L. Hsueh, China. A. T. Ward, Bellefonte, Pa. Zay Jeffries, Cleveland, Ohio. Joel H. Watkins, Washington, D. C. R. W. Kern, Verde, Ariz. J. Wertheimer, Cleveland, Ohio. H. D..Kinney, Easton, Pa. C. R. Wilfley, Ouray, Colo. E. L. Lasier, Washington, D. C. J. P. Wood, Engrs., U. S. A. Carl Zapffe, Brainerd, Minn. Leland D. Adams has left the employ of the Weedon Mining Co., Ltd., at Montreal, Quebec, and is going to Oakland, Calif., where his address will be 1180 Mandana Boulevard.

Jan 5, 1919

By H. J. French

WITHIN the past few years, particularly because of the rapid growth of the airplane industry during the war, considerable attention has been paid to the manufacture of light-wall cold-drawn seamless and welded steel tubing for structural purposes. While the manufacture of such tubing is not, in itself, a difficult matter, some difficulties have. been encountered in producing the same under specifications requiring definite physical properties. It is the purpose of this paper to describe the methods of manufacture and the properties that may be obtained by such methods for tubing coming within about ½ to 2 in. (12.7 to 50.8 mm.) outside diameter and 10 to 22 Birmingham wire gage (0.134 to 0.028 in. wall thickness). Such tubing is largely used as structural material in the aircraft industry, and it is of the utmost importance that the physical and chemical properties should be known, and also that the various factors entering into the manufacture should be under such control as to allow these properties to be varied and held within definite limits. In general, tubing may be divided into four classes: namely, specialty tubing, such as riveted-sheet or plate, lock jointed, etc.; brazed tubing; welded tubing; and seamless tubing. Welded tubing may be divided into hot product, such as lap welded and butt, welded, and cold product, such as acetylene and electric welded. Seamless tubing may be hot rolled or cold drawn.

Jan 9, 1919

By C. K. McArthur

THE subject of classification is so broad that this discussion is confined to what the author believes is of prime importance in connection with proper grinding and classification. The years passed have witnessed many noteworthy changes in fine grinding and classification, which have been accompanied by a readjustment of ore-dressing flowsheets for the preparation of better ground and/or sized products at an expenditure of less power, steel and maintenance than formerly. Nowhere in the industry is more being done in the way of experimental work to lower costs than in grinding circuits, because, at best, grinding costs are high. Recent years have indicated that, on the average, finer grinding has a real application. Without careful preparation of the process feed, no operation can be highly efficient or successful. In an earlier paper, the findings of an extensive survey at representative concentrators were presented1. Also, in the year of 1935, a technical discussion was given by Dr. J. V. N. Dorr (Some Notes on Classification Trends in America) before the Chemical, Metallurgical and Mining Society of South Africa In both papers mentioned, much has been said regarding flowsheets, grinding and classification. The author is very familiar with these papers, having had considerable to do with the actual operation of the flowsheets, as well as large mills and classifiers in the work described. Some data from the second paper have been included in the following discussion. Circulating Load In this particular paper it seems advisable to deal with the classification phases of the work that to a major extent govern the success of any closed-circuit grinding unit. The question has often been asked in connection with a closed circuit: "What circulating-load ratio should be carried?" This is really an

Jan 1, 1937

By J. Nutting, J. W. Cahn

WITH the development of thin film techniques for the direct examination of metals in the electron microscope some new problems in quantitative metallography have become apparent. In order to obtain certain contrast effects in the electron optical image when examining thin films from alloys containing dispersed phases, it is essential to use films of a thickness at least two or three times greater than that of the mean particle diameter of the dispersed phase. From micrographs of such specimens it may be desired to obtain the volume fraction of the dispersed phase and the number of particles of the phase in a unit volume of the matrix. Under these conditions the particles sectioned by

Jan 1, 1960

By A. Lawley, H. W. Schadler

TWINNING has long been recognized as a possible mode of deformation in crystalline solids and has been studied in a wide variety of crystals.&apos; Recently, deformation markings which have the topographical characteristics of twins have been seen in tungsten" and the body-centered cubic alloys of tungsten and molybdenum with rhenium.3-7 These markings have been identified as twins because: 1) they are visible after polishing and etching;2,3 2) their formation is accompanied by an audible click and a drop in load;4 and 3) the habit plane is {112}, the plane which has been identified as the twinning plane for several body-centered cubic metals.&apos; However, there has been no published evidence for the specific determination of the twinning direction in rhenium alloys of tungsten and molybdenum, because usually the deformation twins were not broad enough to be detected with a conventional X-ray beam. Consequently, [111] is inferred as the twinning direction since the latter must lie in a plane of symmetry perpendicular to the twinning plane (112). As Sims and Jaffee3 and Lawley and Maddin4 have shown, the addition of rhenium to molybdenum and tungsten increases the ductility of the alloy over that of the pure metal, but twinning is much more profuse in these alloys than in the pure elements, particularly at Mo-35 pct Re*and W-30 pct Re. Since twinning is often associated with brittle fracture in iron8 and the silicon-irons,9 direct experimental proof that the deformation markings in tungsten and molybdenum alloys of rhenium are twins seemed to be needed. Using the Laue back-reflection technique, the deformation markings in a Mo-35 pct Re alloy are shown to be deformation twins. The twins have a (112) habit plane and the twinning direction is <111>. The Mo-35 pct Re specimen used was taken from a 0.060-in. zone-refined single crystal deformed 6 pct in tension at 78°K. The Laue back-reflection technique, with a film to specimen distance of 2 cm, and white radiation from a copper target were used.

Jan 1, 1962

THE following employment items are made available to AIME members on a non-profit basis by the Engineering Societies Personnel Service, Inc., operating in cooperation with the Four Founder Societies. Local offices of the Personnel Service are at 8 W. 40th.St. New York 18; 100 Farnsworth Ave., Detroit; 57. Post St., San Francisco; 84 E. Randolph St., Chicago 1. Applicants should address all mail to&apos; the proper key numbers in care of the New York office and include 6c in stamps for forwarding and. returning application. The applicant agrees, if placed in a position by means of the Service, to pay the placement fee listed by the Service. AIME members may secure a weekly bulletin of positions available for $3.50 a quarter, $12 a year. MEN AVAILABLE Mining Engineer, 41, married, one child, employed. Broad experience, both underground and open-pit, type mining. Exploration, development, exploitation, industrial construction, milling in northwestern United States. Desires position with progressive, established concern. M-666-259¬Chicago. Recent Graduate, 24, married, no children, B.S. mineral economics. Employed-one year&apos;s experience in development of deposits, study of problem areas. Will accept position anywhere in the world. Available immediately. M-667.

Jan 1, 1952