Search Documents

By Norris Johnston, Carrol M. Beeson

For many years the permeability of reservoir sands has been measured by flowing air through a cleaned and dried core sample. This differs from the true reservoir permeability in one important respect: the rock particles in the reservoir are surrounded by interstitial water, not air, and their physical shape and condition of hydration are greatly dependent thereon. Permeability as defined must be measured with a single-phase fluid. Since no means exist for removing the oil and gas from a core sample by simply flowing water through it, the sample must be cleaned and then resatu-rated with water before testing. The present discussion attempts to show that after the cleaning process a considerably different permeability is determined with salt or fresh water than is obtained with air. The postulate is made that the salt-water permeability is probably closer to the true reservoir permeability than is the measurement with air. This is discussed in relation to both physically possible and economically feasible measuremerits. Data On more than 1200 core samples are given to show the nature of the effects observed, and a plea is made for others to consider water permeability measurements as a routine necessity, eventually replacing air permeability in regions where the differences are great. Introduction Permeability is defined1 as a "a measure of the capacity of a porous medium to transmit fluids, when there is no interaction between the solids and the fluid." Darcy's law of liquid flow in porous media states: kA?P QµL/A?L [I] where Q represents milliliters of liquid of viscosity p centipoises passed per second through a porous medium of permeability k darcys and cross-sectional area A sq. cm. under a pressure gradient ?P/L atmospheres per centimeter, the flow being understood to be laminar or viscous, not turbulent. This equation defines the darcy. For the case of radial flow in a uniform sand, such as usually exists in the neighborhood of a well in an oil or gas sand, Darcy's law becomes:2 Here h is the net sand thickness in feet, Pe and Pw are pressures at the drainage radius4 and well radius, and re and rw are these radii, respectively. The productivity index3 is defined as the barrels of liquid produced per day per pound per square inch mean pressure differential between ferences and well bore, and is thus: By further definition, the specific productivity index is: or in terms of practical units, and allowing for shrinkage:

Jan 1, 1945

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,' and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6'7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.' EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.' Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969

US Tin Mission To Study Costs in Far East A move to obtain adequate supplies of tin at prices the United States is willing to pay was initiated when the interagency tin mission left for the Far East. The Mission, which includes representatives of the Reconstruction Finance Corporation, State Department, Defense Minerals Procurement Agency and the Bureau of Mines will go to Indonesia and Malaya. The primary purpose of the mission, according to officials, will be to study tin production costs, not to negotiate for the purchase of tin. The mission will be prepared to enter into negotiations, if the Far Eastern producers are amenable. The United States withdrew as a large-scale buyer of tin some months ago in protest against what it considered exorbitant prices being charged in the Singapore market. Subsequent attempts to negotiate for a steady tin supply at what this country considers reasonable prices have been unavailing. The U. S. is prepared to enter into a two or three year contract with the price of tin somewhere between $1.00 to $1.12 per lb. The decision to abstain from the market has not yet put a squeeze on U. S. supplies. Substantial quantities of tin still are coming in from Malaya under an old contract.

Jan 12, 1951

By R. Schuhmann, O. W. Moles

at temperatures of 1150°, 1250°, and 1350°C for liquid copper sulphides ranging in composition from saturation with Cu to about 21.5 pct S. From the experimental data, activities of Cu, S, and Cu2S in the melts were calculated. Also, the results furnish a new determination of the location of the curve showing the compositions of Cu-saturoted sulphide melts in the CU-S constitution diagram. THE "white metal" made as an intermediate L product in converting copper matte to blister copper is a matte approximating Cu2S in composition. It has long been known that liquid Cu-S mattes can exist at a given temperature over an appreciable composition range, with S:Cu ratios ranging up from a lower limit corresponding to equilibrium of the matte with a liquid Cu phase. The Cu-saturated matte has somewhat less S than Cu2S, although previous measurements of the compositions of Cu-saturated mattes are not in good agreement.'" As the S:Cu ratio approaches and slightly exceeds that for Cu2S, the partial pressure of sulphur gas over the liquid matte rapidly approaches atmospheric pressure,5 so that Cu-S melts with much more S than Cu2S can be made and handled only in pressure apparatus. Accordingly, the liquid copper sulphides of interest in copper smelting and readily studied experimentally fall in a relatively narrow composi- tion range about Cu2S. The freezing points of Cu-S mattes show a maximum of 1129°C near the composition Cu, dropping to 1105oC for Cu-saturated mattes having less S and dropping under 1100°C for higher S mattes.' Estimates of the sulphur pressure and other thermodynamic properties of liquid Cu,S were made by Kelley; based on extrapolations from equilibrium measurements on solid Cu,S. More recently, Cox and coworkers' studied equilibria in the reaction: Cu,S + H, e 2Cu + H,S over the temperature range 700" to 1250°C. They measured equilibrium H2S:H2 ratios presumably with both the sulphide and the metal phase present, so that their data above the melting point of Cu,S should measure the S pressure of Cu-saturated sulphide melts. The sulphur pressures of liquid copper sulphides of several S:Cu ratios at their freezing points can be estimated from data given by Posnjak, Allen, and Merwin." However, beyond these few data, no systematic study seems to have been made of the relations of sulphur pressure and other chemical properties of liquid copper sulphides to composition and temperature. The measurements of the sulphur pressures of liquid copper sulphides reported in this paper represent a first step in the quantitative study of the chemistry of mattes. Similar work is planned on

Jan 1, 1952

By G. T. Higgins

PREVIOUS workers1,2 have found evidence of exaggerated grain growth or secondary recrystallization on annealing sponge zirconium at temperatures high in the a, phase field, but no details of the orientation relationship between the secondary grains and "as-recrystallized" matrix were reported. In other hexagonal metals, namely dilute Mg-A13 and Cd-zn4 alloys, secondary recrystallization has been observed in which the secondary grains are related to the primary recrystallized structure by rotations about the c axis. These rotations are thus comparable with the rotations about the (111) axis observed in the secondary recrystallization of fcc metals. In the current work secondary recrystallization has been observed on annealing iodide zirconium at 800°C and the associated changes in crystallographic texture have been examined. The material employed was arc-melted iodide zirconium of the following composition: Impurity O H Fe Hf Pb I Ni C1 A1 ppm by wt 130 5 230 98 23 28 200 39 30 This was received as 0.25-in. plate, and, prior to the annealing studies, was cold-rolled to 0.040 in. Specimens 1 in. sq were chemically polished and annealed for various times at 800°C in a vacuum better than 5x 10-6 Torr. For metallographic examination specimens were first chemically polished and then anodized8 to enhance contrast between the grains when examined under polarized light. Changes in crystallographic orientation associated with the development of secondary grains were followed by (1011) and (0002) pole-figure determinations using a conventional Schulz goniometer in reflection. Filtered Cr Ka radiation was employed and great care was taken to avoid spurious re- sults due to the close proximity of the Bragg angles for the (1011) and (0002) reflections. Figs. 1 and 2 illustrate the change in grain structure on annealing at 800°C. After 24 hr the structure has ceased to be equiaxed due to the development of certain grains in preference to others. It is notable that the secondary grains do not grow to the extent observed in sponge zirconium.1,2 This appears to be due in part to the fact that normal grain growth is inhibited in the less pure sponge zirconium, with the result that the driving force for secondary recrystallization remains high, while at the same time the number of grains able to develop in the presence of the impurities is also smaller. As a consequence, in sponge zirconium those grains that do develop preferentially are able to grow into the fine -grained matrix without impingement, while in iodide zirconium the preferential growth of many grains leads to early impingement. The pole figures determined for specimens annealed for 5 min and 24 hr at 800°C are illustrated respectively in Figs. 3 and 4. These indicate that the dominant feature of the initial recrystallized texture consists of basal planes at an angle of 321/2 deg to the sheet surface, with a (1120) axis lying parallel to the

Jan 1, 1967

By F. M. d’Heurle

Films of molybdenum have been prepared by sputtering onto oxidized silicon substrates. The resistivity. lattice parameter, orientation, and grain size were studied as a function of substrate temperature and substrate bias. Under normal sputtering conditions, the resistivity of the films was found to be quite high (600 x 10 ohm-crn). However, with the use of the negative substrate bias of 100 v and a substrate temperature of 350°C, films weve produced with a resistivity of ahout twice that of bulk molybdenum. The lattice parameters measured in a direction nornzal to the surface of the films weve found to be gveatev than the bulk value. This was interpreted as being at least partly due to the presence of compressive stresses. The effects of annealing in an Ar-H atmosphere were studied in terms of diffraction line width, lattice parameter, and resistivity. BECAUSE of its relatively low bulk resistivity (5.6 x 106 ohm-cm)' molybdenum is potentially interesting as a thin-film conductor in integrated circuits. An additional feature which makes it attractive for this purpose is its low coefficient of expansion (5.6 x KT6 per "c),' which is fairly well matched to that of silicon (3.2 x 10 per c). It is possible to deposit molybdenum films by evaporation but generally films produced in this manner have a high resistivity. In order to achieve resistivities close to bulk value, Holmwood and Glang found it necessary to operate in a vacuum of about 107 Torr and to maintain the substrates at 600 C during film deposition. Sputtered molybdenum films have been examined by Belser et a1.7 and, recently, by Glang et al.' This paper describes the results of an attempt to extend some of that work and examine the effects of annealing and getter sputtering on the physical and structural properties of the films produced. SPUTTERING APPARATUS AND PROCEDURE The apparatus used for most of the film sputtering work described here consisted of two "fingers" serving as anode and cathode, respectively, which were mounted within an 18-in.-diam glass chamber. A liquid nitrogen-trapped 6-in. diffusion-pump system was used to achieve a vacuum of about 1 x 107 Torr within the chamber prior to sputtering. The essential features of the equipment are shown in Fig. 1. Cathode and anode fingers are stainless-steel tubes isolated from the top and bottom plates by Teflon collars. In order to limit the discharge to the space between anode and cathode, each finger is surrounded by an aluminum hield, at ground potential, having an internal diameter 18 in. larger than the outside diameter of the finger. The cathode and anode fingers are 6 and 4 in. in diam, respectively. A 116-in.-thick sheet of molybdenum is brazed with a 10 pct Pd, 58 pct Ag, 32 pct Cu alloy to a copper disc which is mounted by means of screws and a large 0 ring onto the lower end of the cathode finger. The disc is cooled during sputtering by water circulation inside the finger. The use of several feet of plastic tubing for the water input and outputg reduces leakage to ground to less than 1 ma when the cathode potential is raised to 5 kv. The upper end of the anode finger is terminated by a brazed-on copper block. A variety of specimen holders can be easily mounted on the upper face of this block. Substrate heating or cooling is achieved by use of an appropriate unit attached to the lower face of the same block. Heating is achieved by means of cartridge-type heaters and cooling by copper coils fed with forming gas under pressure. The inner chamber of the specimen finger constitutes a small vacuum chamber of its own which is evacuated by an auxiliary mechanical pump in order to limit heating element oxidation and heat transfer by convection currents. An advantage of the finger arrangement is the absence of cooling and heating coils and wires within the main chamber. The stain less-steel shutter is useful to establish a discharge for cleaning the cathode at the beginning of each sputtering run. Water cooling of the shutter reduces heating and the out-gassing of impurities which might condense on the nearby substrates. Unless otherwise specified, the substrates used in these experiments were 1-in.-diam oxidized silicon wafe:s, 0.007 in. thick, having an oxide thickness of 6000A. The substrate holders were large copper discs onto the surface of which a number of molybdenum discs, 116 in. thick and 78 in. in diam, were brazed. The wafers were clamped to the molybdenum discs

Jan 1, 1967

By R. A. Morse, P. M. Bridges, L. E. Wilsey, Howard N. Hall, P. L. Terwilliger

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By L. E. Wilsey, R. A. Morse, P. L. Terwilliger, Howard N. Hall, P. M. Bridges

Theoretical and experimental investigations of a constant pressure gravity drainage system are reported. Experimental data are presented to show that recovery to gas breakthrough by gravity drainage is inversely proportional to rate. The gravity drainage reference rate, which is numerically equal to the so-called "maximum theoretical rate of gravity drainage" is shown to have no particular significance from a recovery standpoint. Before this rate can be used as a basis of comparison for recoveries, it is necessary that the relative permeability and capillary pressure characteristics and displacing fluid viscosities be identical for the systems compared. A method is presented by which accurate prediction of the performance of a gravity drainage system can be made. Close agreement between experimental and calculated drainage performance shows that steady state relative permeability and static capillary pressure data can be used to describe fluid displacement behavior. The very wide range of liquid recoveries before gas breakthrough which result from production rate variation alone demonstrates the importance of this factor in planning depletion of a gravity drainage reservoir. Calculated results are presented which show that little additional recovery can be expected from a high pressure gravity drainage system between the times of gas breakthrough and attainment of such high gas/liquid ratios as to make further pressure maintenance impractical. INTRODUCTION It bas been recognized for some time that gravity forces play an important part in the recovery of oil from some types of reservoirs. Field experience has shown that under certain conditions, gravity drainage can result in very high oil recov- eries. Qualitative reasoning has led most engineers to the general conclusions that: (1) Where gravity drainage is important, the reservoir pressure should be maintained by gas injection at the crest of the structure to prevent shrinkage of the oil in place and to keep a low viscosity so the oil can drain at the fastest possible rate. (2) Recovery by gravity drainage is rate sensitive. A survey of the literature indicates that while considerable work has been done on the effects of gravity in oil production problems, no satisfactory method of calculating the performance of gravity drainage reservoirs has been reported.1,2,3,4,5 In the absence of any proven method of calculating reservoir performance, the level at which pressure should be maintained and the rate of production for most efficient operation has been open to debate. The limits and general character of the recovery us rate relationships are apparent from the following: As rates of production approach zero, oil will drain by virtue of its own weight fast enough that the saturation distribution is always approximately the same as the original static capillary distribution. That is, at the gas-oil contact the liquid saturation goes from 100 per cent to a value of perhaps 10 to 30 per cent in a very short distance, so that as production continues. a relatively sharp gas-oil contact moves down-structure, leaving a very low residual oil saturation in the originally oil saturated zone. At very high rates of production, the oil that drains by virtue of its own weight is negligible and recovery will approach that of a horizontal gas drive, leaving a much higher residual oil saturation. At intermediate rates of production. recovery should be between these extreme*. Despite the lack of quantitative methods, tentative agreement had been reached on the question of optimum producing rate. It has been generally concluded that rather sharp decrease in recovery would occur at rates of production above the "maximum rate of gravity drainage" and hence this rate should not be exceeded. The "maximum rate of gravity drainage" is defined as the rate of production from a 100 per cent

Jan 1, 1951

By Eckhard Nembach

The phase diagram of the system Pb-In has been investigated between -27° and + 40°C, using nzainly X-ray dijfraction. In accordance with t her mo dynamic measurements by Heumann and Predel, a segregation occurs at low temperatures, though not in the form of a nziscibility gap. THE phase diagram of the system Pb-In has been the subject of extensive investigations,1&apos;1 but recently Heumann and prede13 concluded from their thermodynamic data that a new feature should occur below room temperature. These authors observed that the maximum values for the enthalpy and entropy of mixing, which occurred at a composition of 50 at. pct Pb, were +400 and —1.7 cal per g-atom deg, respectively. From this the authors estimated that a miscibility gap should occur below 30°C, centered at 50 at. pct Pb. Resistivity measurements seemed to support this view. These authors proposed the phase diagram outlined in Fig. 1. Three phases exist at 30°C: the tetragonal indium phase with c/a > 1, the tetragonal intermediate phase a, with c/a < 1, and the fcc lead phase. During an investigation of the superconducting properties of Pb-In alloys. it has been observed4 that aging a specimen with 50 at. pct Pb for 14 days at -18°C decreased the superconducting transition temperature about 0.13"K and tripled the transition width. In this paper, the results of an investigation of the Pb-In phase diagram in the temperature range from — 2T to +40°C are reported. Superconductivity and X-ray methods have been used. 1) SPECIMEN PREPARATION The materials were provided by the American Smelting and Refining Co. According to the manufacturer their purity was 99.999 pct. The weighed amounts of the constituents were sealed in quartz tubes under an atmosphere of 10 torr helium, mixed for 24 hr in a rocking furnace at 380°C, quenched in ice water, and homogenized at 20" to 30°C below the solidus line, established by Heumann and Predel. The annealing times were 144 hr for specimens containing Less than 30 at. pct Pb and 36 hr for the remainder. 2) SUPERCONDUCTIVITY EXPERIMENTS The specimens were quenched from the homogeniza-tion treatment into ice water and their superconducting transition temperatures T, measured. The procedure used has been described in Ref. 4. The transition was detected by the change of the mutual induc- tance of two coaxial coils containing the sample. T, was defined as the temperature at which 50 pct of the total change in inductance had occurred. The repro-ducibility with which T, could be measured was i0.002"K. Then the specimens with lead contents between 38 and 75 at. pct were aged for 7 days at temperatures between -30" and 40°C. If this treatment caused T, to change by more than 0.005"K or the width of the transition to increase by more than 0.002"K, it was concluded that the specimen had undergone a phase change and no longer consisted only of the fcc lead phase: as it did immediately after homogenizing. The result is shown in Fig. 2. From this one can estimate at what temperatures and concentrations phase changes occur. The X-ray measurements were based on these preliminary results. 3) X-RAY EXPERIMENTS Because of the softness of the material, relatively coarse powders. 75 p, had to be used, which were filed in a helium atmosphere from homogenized specimens. The powders were annealed at least 30 min at temperatures between 120" and 16OJC, depending on their concentration, and quenched in ice water. Then their X-ray patterns were taken at -178°C with a Picker diffractometer, model 3488K, and a cold stage. on which the specimen was in thermal contact with a liquid-nitrogen reservoir. In this way the following relation was established for the fcc lead phase: a = 4.697 + 0.00247C for 40 5 C 5 75 11 where n is the lattice constant (A) and C is the at. pct of lead. The coarseness of the powder made it impossible to use lines with 0 > 75 deg; therefore n was averaged from lines with 45 deg 5 0 5 75 deg. The results were reproducible to within i0.05 pct. Relation [I] is very similar to the one found by Heumann and Predel at room temperature. Following this, homogenized specimens with compositions between 15 and 56 at. pct Pb were aged for at least 10 days at temperatures between -27" and

Jan 1, 1970

By F. C. Stanford

THE work of an engineer is to direct natural forces so that they bring about the results that he wishes to secure. Heretofore he has concerned himself chiefly with physical forces and inanimate objects, until he has secured a truly marvelous degree of control over them. The great problem of the present age is to secure a like degree of knowledge and control of the human factor. Progress has already been made along this line, but, it is only a beginning. Wilhelm Ostwald says that scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to maintain a high average in prophecy. In short, the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essential need of the period is for more brains; if we only had sufficient knowledge and sagacity we could not only solve all difficulties, but prevent them from arising. This generalization holds good for an industrial organization. The most vital need of the management is for more brains. The logical course for an engineer in charge of an industrial organization is, therefore, to direct whatever forces may be at his command toward the development, training, and guiding of all the brains in his organization. This is easier said than clone, for it involves the carrying on toward two objectives, the maximum of productive work, and the development of the individuals who perform it. This is essentially like the rebuilding and enlarging of a plant, keeping it in full operation the while. On the other hand, if the aim is merely for maximum production from an organization, without offering opportunity for development, the final outcome will necessarily be like that f a plant that is driven at full capacity without stopping for repairs or improvements; it eventually becomes so run down that either a complete rebuilding is necessary or else it has to be abandoned.

Jan 2, 1918

By N. F. Dyson, T. R. Scott

The iilzfluence of catalytic agents on the oxidation of ZnS has been studied under pressure leaching conditions, using a chemically prepared sample of ZnS which was substantially unreactive on heating at 113°C with dilute sulfuric acid and 250 psi oxygen. Nurnerous prospective catalysts were added at the ratio of 0.024 mole per mole ZnS in the above reaction but pvonounced catalytic activity was confined to copper, bismuth, rutheniuwl, molybdenum, and iron in order of. decreasing effectiveness. In the absence of acid, where sulfate was the sole product of oxidation, catalysis was exhibited by copper and ruthenium only. Parameters affecting the oxidation rate were catalyst concentration, temperature, time, oxygen pressure, and a7riount of acid, the first two being most important. The main product of oxidation in the acid reaction was sulfur, with trinor amounts of sulfate. An electrochemical (galvanic) mechanism has been suggested for the sulfuv-forming reaction, whereby the relatively inert ZnS is "activated" by incorporation of catalyst ions in the lattice and the same catalysts subsequently accelerate the reduction of dissolved oxygen at cathodic sites on the ZnS surface. Insufficient data was obtained to Provide a detailed mechanism for sulfate fornzation, which is favored at low acidities and probably proceeds th&apos;rough intermediate transient species not identified in the preseni work. THE oxidation of zinc sulfide at elevated temperatures and pressures takes place according to the following simplified reactions: ZnS + io2 + H2SO4 — ZnSO4 + SG + HsO [i] ZnS + 20,-ZSO [21 In dilute acid both reactions occur but Reaction [I] is usually predominant, whereas in the absence of acid only Reaction [2] can be observed. Both proceed very slowly with chemically pure zinc sulfide but can be greatly accelerated by the addition of suitable catalysts, as suggested by jorling&apos; in 1954. Nevertheless, an initial success in the pressure leaching of zinc concentrates was achieved by Forward and veltman2 without any deliberate addition of catalytic agents and it was only later that the catalytic role of iron, present in concentrates both as (ZnFe)S and as impurities, was recognized and eventually patented.3 It is now apparent that another catalyst, uiz., copper, may have also played a part in the successful extraction of zinc, since copper sulfate is almost universally used as an activator in the flotation of sphalerite and can be adsorbed on the mineral surface in sufficient amount The importance of catalysis in oxidation-reduction reactions such as those cited above has been emphasized by various writers and Halpern4 sums up the situation when he writes that "there is good reason to believe that such ions (e.g., Cu) may exert an important catalytic influence on the various homogeneous and heterogeneous reactions which occur during leaching, particularly of sulfides, thus affecting not only the leaching rates but also the nature of the final products." Nevertheless relatively little work has appeared on this topic, one of the main reasons being that sufficiently pure samples of sulfide minerals are difficult to prepare or obtain. When it is realized that 1 part Cu in 2000 parts of ZnS is sufficient to exert a pronounced catalytic effect, the magnitude of the purity problem is evident. An incentive to undertake the present work was that an adequate supply of "pure" zinc sulfide became available. When preliminary tests established that the material, despite its large surface area, was substantially unreactive under pressure leaching conditions, the inference was made that it was sufficiently free from catalytic impurities to be suitable for studies in which known amounts of potential catalytic agents could be added. The first objective in the following work was to identify those ions or compounds which accelerate the reaction rate and, for practical reasons, to determine the effects of parameters such as amgunt of catalyst, temperature, time, acid concentration, and oxygen pressure. The second and ultimately the more important objective was to make use of the experimental results to further our knowledge of the reaction mechanisms occurring under pressure leaching conditions. The fact that catalysts can dramatically increase the reaction rate suggests that physical factors such as absorption of gaseous oxygen, transport of reactants and products, and so forth, are not of major importance under the experimental conditions employed and an opportunity is thereby provided to concentrate on the heterogeneous reaction on the surface of the sulfide particles. As will appear in the sequel, the first of these objectives has been achieved in a semiquantitative fashion but a great deal still remains to be clarified in the field of reaction mechanisms. EXPERIMENTAL a) Materials. The white zinc sulfide used was a chemically prepared "Laboratory Reagent" material (B.D.H.) and X-ray diffraction tests showed it to contain both sphalerite and wurtzite. The specific surface area, measured by argon absorption at 77"K, varied between 3.9 and 4.6 sq m per g. Analysis gave 65.0 pct Zn (67.1 pct theory) and 31.9 pct S (32.9 pct theory). Other metallic sulfides (CdS, FeS, and so forth) used in the experiments were also chemical preparations of "Laboratory Reagent" grade. Samples of mar ma-

Jan 1, 1969

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution&apos;s research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof&apos;s rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel&apos;s photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

By Ralph K. Foster

During five underground mine fires which occurred in Arizona during 1980 and 1981, sealing the fire area became necessary. To minimize leakage into the fire area, ventilation control measures were instituted to balance pressure across the bulkheads. Problems en- countered in sealing the fire areas and measures taken to improve these conditions are discussed. The routing of the ventilation and ventilation control to en- sure the workers&apos; safety were also important considerations in reopening the mines. The use of continuous CO monitors is discussed. One important consideration was the condition of the fire, and chromatographic analysis was used to establish this. Graphs comparing the Trickett ratio, carbon monoxide, carbon dioxide, and oxygen concentrations are given. The Trickett ratio was useful but needed to be augmented by the comparison of CO, C02, and 02. Problems with getting good samples from sealed areas and recommended procedures that were developed during these fires are discussed.

Jan 1, 1982

By Eugene N. Cameron

Pegmatites occur in abundance in certain areas of South West Africa and in adjacent parts of northern Cape Province in the Union of South Africa. Some of the pegmatite deposits were prospected before World War I, and intermittent mining was done during the period between the two World Wars. The deposits of the Jooste lithium mines became an important source of lepidolite, and beryl, columbite-tantalite, wolframite, and other minerals were produced. Since World War I1 prospecting and mining have been carried on vigorously, with the result that South West Africa produced nearly 3000 tons of beryl during 1949 through 1953, together with more than 40,000 tons of lithium minerals, chiefly lepidolite and petalite. Small amounts of tantalite, columbite, and other minerals have also been produced during the postwar period. Most of this mineral production has come from two pegmatite areas roughly outlined in Fig. 1. One is the Karibib-Omaruru area of north central South West Africa. The second is the northeastern part of the Orange River pegmatite area, which extends into adjacent parts of Namaqualand, in northern Cape Province of the Union of South Africa

Sep 1, 1955

By K. Stout, L. Friel

Some rock mechanics theorists believe that if a hydraulically placed backfill can be introduced in a stoped out area, which will minimize wall closure by taking high stresses across the fill with minimum compaction, then heavy ground and rock burst phenomena will be minimized. The paper will discuss a large scale laboratory project when fill strength was increased over four times by the head vibrated method and up to well over 20 times by the double placed, cemented, vibrated head method when compared to conventionally placed fills. The only preconditioning of the 60% solids by weight slurry was the addition of cement in some tests.

Jan 1, 1983

TO THE BOARD OF DIRECTORS AND MEMBERS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS. GENTLEMEN: Submitted herewith are the report of the Treasurer for the year 1941 and re¬ports for the same year of the following standing committees: Admissions, Mem¬bership, Papers and Publications, Mining and Metallurgy (Magazine), Library, and Student Relations. These reports present additional details. Membership For the fourth year in succession, mem¬bership reached a new all-time high, level as shown in Table 1. The total at the

Jan 1, 1942

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

The great Bingham Canyon mine and mill complex of Magna, Arthur, and Bonneville had their beginning in a 300 ton per day operation which was commenced by Daniel C. Jackling and his associates in 1904 as the Utah Copper Company. This small plant was quickly expanded to 500 tons per day and eventually Kennecott, the Utah Copper successor, was processing about 45,000 tons per day of ore in each of its mills, Magna and Arthur. Finally, in 1966, the Bonneville crushing and grinding plant was added to produce a slurry of ground ore for flotation concentration at the expanded Magna and Arthur mills. Bonneville is one of the few railroad dump primary gyratory crushing plants constructed in recent years; another which is described in this Monograph is Cuajone in Peru, started in 1976. Two others are the Climax Henderson unit and the Phelps Dodge Tyrone crusher, which has been fed by trucks since it commenced operation. The Bonneville, Henderson, and Cuajone crushers are all located considerable distances from their mines, hence the use of rail haulage. Shovels in the Bingham pit are 8 to 15 yd capacity; and ore is sent to the Bonneville crusher in 100 ton rail cars, where they are dumped, two at a time, by a hydraulically driven rotary dumper. Ahead of the 54 in. by 74 in. Allis-Chalmers gyratory are two grizzlies, each 27 ft 9 in. (8.46 m) long with bar spacings of 4 ½ in. (114 mm) at the feed end and 6 in. (152 mm) at the discharge end. Grizzlies are sloped at 38. Oversize rocks are re- moved from the crusher pocket by an overhead crane, and the crusher produces a nominal 6 in. (152 mm) product. Rail cars are dumped in the direction away from the crusher, and water sprays at the dumper level and in the rock boxes are used for dust suppression. There are two 72 in. by 19 ft (1.83 m by 5. 8 m) apron feeders under the 500 st cr&apos;ushed ore pocket and two more under the grizzly undersize pocket. Feeder speeds are variable up to 72 fpm. Grizzly undersize is dropped to the feeder pocket by three shelves forming a rock ladder attached to the pocket walls. Each pair of apron feeders, one for crushed ore and one for grizzly undersize, discharge to a 72 in. (1. 83 m) picking belt for tramp removal; this belt feeds one of two 54 in. (1.37 m) feeder conveyors which in turn discharge to a 60 in. (1. 52 m) takeaway belt operating at 175-300 fpm (53.3 - 97.4 mpm). Both picking belts are equipped with metal detectors and tramp iron magnets, and a separate 30 in. (760 mm) conveyor is used to remove tramp material.

Jan 1, 1978

By J. Hall Carpenter, James E. Lawver

Shortly after the passage of the Taconite Amendment in Minnesota, several mining companies announced their intention to build new magnetite taconite plants and another announced its intention to augment present facilities. It is clear that Minnesota will enjoy an expanding magnetite taconite industry, but despite the fact that the reserves are large, eventually they will have to be supplemented by oxidized deposits. Furthermore, not all producers have magnetite taconite reserves. Due to the extensive oxidation of most of the western part of the Mesabi Range, there are no large blocks of unaltered magnetite taconite that lend themselves to open pit operations. Unless a commercial process can be developed to concentrate the oxidized, or so- called "nonmagnetic", taconite and semi-taconite, the existing mines operating in the western part of the range will be forced to shut down when the direct shipping, wash and gravity ores are depleted, or are no longer salable, because of their poor quality compared to high-grade pellets. KNOWN PROCESSES COSTLY The enormous reserves of the oxidized iron- bearing formation have offered a tantalizing challenge to metallurgists for many years. In fact, several processes for concentrating certain types of oxidized ore have been successful at both laboratory and pilot plant level, but to date no process for concentrating semitaconite or oxidized taconite has reached commercial fruition. Magnetic roasting, followed by low-intensity magnetic separation1, has shown considerable promise because the high iron recovery makes the ratio of concentration of many of the oxidized ores more favorable than that of magnetite taconite. However, the capital and operating costs are high and, in many cases, a high- grade concentrate cannot be made without resorting to flotation of the magnetic concentrate. Hence, most research groups are investigating alternate methods of concentration with the hopes of reducing the cost.

Jan 9, 1965

Correlation between Metallography and Mechanical Testing By H F MOORE (Henry Marion Howe Memorial Lecture Trans, vol 120 11,000 words ) The lack of effective correlation between metallography and mechanical testing from the days of Reaumur to the present is noted, and two general problems of such cor¬relation are stated (1) the correlation of qualitative test results with quantitative, and (2) the correlation of average results with maximum or minimum results Some correlation has been achieved, notably in the field of heat-treatment and in the study of elastic strength of metals Correlation is in the process of being developed in several other fields, including the quantitative study of the effect of grain size of metal on mechanical properties, of grain size and type of crystalline structure on the sensitivity of metals to weakening at holes, notches and other "stress raisers," and in the study of the starting phases of spreading, "fatigue" cracks Correlation of mechanical test results and metallographic study is needed in the study of such problems as the various theories of failure of metals, the meaning of and tests for service ductility of metals, and the relative damaging effect of defects inherent in metals, such as minute cracks and segregation, as compared with the damaging effect of "imposed" stress raisers, such as screw threads, sharp shoulders, etc The neces¬sity for more correlation of metallography and mechanical testing during student days is emphasized, and also the need of a better understanding on the part of engi¬neers of the significance and limitations of metallographic apparatus and results and of X-ray diffraction This should be matched by a better understanding on the part of metallurgists of the significance and limitations of mechanical tests of metals, of testing machines and strain-measuring apparatus

Jan 1, 1937