Search Documents

By L. B. Slichter

After statement of the principles of similitude which apply to electromagnetic modeling, charts showing the inductive response of conducting spheres as dependent upon frequency, conductivity, and size are exhibited in this paper. The shape of the curve which relates intensity of response to frequency is significant in indicating the advisability of low frequencies in the exploration for conducting bodies, when consistent with the securing of a large percentage of the ideally possible response. Comparisons of theoretical response and that observed with models are shown, and relationships with the subject of applied electromagnetic prospecting are indicated. Maxwell Field Equations The Maxwell field equations summarize the physical laws that govern electrical field phenomena; they are the basis for the solution of electromagnetic problems. These concise equations, with adequately formulated boundary conditions, specify the complete electrical condition of continuous media, and the development of their solution amounts merely to a more convenient re-expression of phenomena already completely described. Thus, the immediate content of the field equations themselves is sufficient and sometimes convenient for the treating of certain questions (such as those relating to electromagnetic models) which are independent of the special factors of geometry, or the nature of an impressed field. The four Maxwell field equations are written below, in c.g.s. gaussian units: curl E = -B/c [21 div eE = 4pp [31 div B = 0 [41

Jan 1, 1932

By Jack White, Ralph B. Adair

The Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1934, 1935, 1936, 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. Ore Treated The ore consists of fine grained highly siliceous, felspathic and argillaceous quartz- ites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about I oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or,, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct- Crushing Operations The first stage of crushing is done under. ground where the oversize from I2-in. grizzlies is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35O slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a.rate of over 500 tons per

Jan 1, 1949

By B. Ancker, E. R. Parker

The small-angle dislocation-boundary density of nickel and some of its alloys was investigated as a function of strength. It was found that the strength is a linear function of the density for pure nickel and for Ni-Ti alloys, but not for Ni-Co alloys. The results are interpreted in terms of dislocation theory. THE processes by which metals deform are still poorly understood, even though there has been a concentrated research effort in this field during the past fifteen years. Single crystals and individual grains in polycrystalline aggregates often develop a subgrain structure when deformed. Substructure formation occurs as a result of local plastic bending and its development is augmented by annealing at moderate temperatures.' Investigations made to date, largely qualitative in nature, have shown that the substructure is composed of a network of small-angle boundaries. The purpose of the present paper is to present some quantitative data on substructure (obtained by X-ray techniques) and to correlate the results with the strength of the metal in which the substructure existed. Nickel and some of its alloys were used for the experiments. The presence of certain kinds of foreign atoms greatly alters the formation and effect of the substructure. Polycrystalline tensile specimens were prepared from high purity nickel, two Ni-Ti alloys, and two Ni-Co alloys; the composition of these materials is given in Table I. Tensile specimens having a reduced section 1/4 in. diam by 3 in. long were machined from materials which were refined, cast, forged, and swaged in the authors' laboratories. The specimens were annealed for 1/2 hr at 1150°C, a treatment which produced grains having a diameter of approximately 0.5 mm. This rather large grain size was used to facilitate later examination of the substructure. Duplicate specimens of pure nickel and of each alloy were strained various controlled amounts in tension at room temperature and recovered for 1 hr at 800°C. (This strain induced prior to recovery will be referred to hereafter as the "prestrain.") One of each of the recovered specimens was pulled in tension at room temperature to obtain the stress-strain curves. The other bar was cross-sectioned in the gage length, carefully polished, and deeply etched to remove all cold-worked material. This specimen was then examined by the X-ray microscopic technique2 to determine the nature and magnitude of the substructure. The use of duplicate specimens permitted a direct correlation between tensile properties and substructure characteristics. X-ray microscopic studies were made with an apparatus constructed to have an average resolving power of about 4 microns. The monochromatic radiation reflected from grains which were oriented favorably was recorded on fine-grain photographic plates. These were examined at Xl00 which represents the true magnification, since there was essentially none in the X-ray system. This permitted detection of angular differences between subgrains of as little as 10 min. A very large number (over 100) of grains for each specimen was examined at this magnification and the number of substructure boundaries per grain was tabulated. An accurate relative measure was obtained under fixed experimental conditions, e.g., same grain size, resolving power, magnification, etc. The greatest source of error lay in counting the subboundaries, but this proved to be surprisingly small when repeated counts were made by different investigators. Furthermore, as the subsequent analysis indicates, whatever human error was introduced was not significant. Analysis of the Substructure Data When the number of substructure boundaries per grain was plotted against the frequency, skew (asymmetrical) distribution curves of the type shown in Fig. 1 were obtained. These are smoothed curves for the 1 atomic pct Ti in nickel alloy subjected to various prestrains and are representative of the curves obtained with all the metals. Since skew-distribution curves cannot be analyzed by elementary statistical methods, detailed investigations were undertaken in order to 1—test the consistency

Jan 1, 1955

By K. E. Gray

The status of rock mechanics as applied to petroleum production might be termed, "Rock Mechanics-A New Name for Old Problems." The petroleum industry's efforts, from its earliest days, have been concerned with rocks, hopefully containing hydrocarbon accumulations in economic quantities. Geophysical and geological studies, wildcat and development drilling procedures, well bore mechanics and reservoir engineering operations, and certain aspects of production operations involve rock mechanics in various ways. Stress states and temperatures of interest range from low values in surface or near-surface activities, to very high values encountered at depths now exceeding 25,000 ft; deeper and deeper drilling will continue to increase this range. Time scales vary from a few microseconds in wave propagation measurements and some aspects of rock behavior during drilling, to seconds, minutes or hours for other drilling and well bore mechanics problems, to several years during which the efficient and economical depletion of reservoir systems is achieved. Subsurface sedimentary formations contain various fluids, of course, and reservoir fluid movement commonly involves three-dimensional, three-phase (oil, gas, and water) fluid flow. Many extremely difficult problems in rock mechanics arise for the Petroleum Engineer because of fluid movement (or lack of desired movement) in a well bore or reservoir. The discussion to follow illustrates just a few of the many topics in rock mechanics of significance to the petroleum industry. Time precludes anything other than a superficial treatment of the topics mentioned. A great deal of work has been carried out by various research groups in the petroleum field and significant efforts are continuing, as a review of the technical literature will reveal.

Jan 1, 1968

By G. Y. Chin, M. T. Dolan, W. L. Mammel

In the case of plastic deformation by slip, von Mises&apos; showed that an arbitrary shape change of a crystal generally requires the activation of five independent slip systems. The selection of the five active systems was worked out by Taylor ,&apos; who hypothesized that, among all combinations of equivalent slip systems which are capable of accommodating a given imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Taylor analyzed the case of {lll}( 110) slip for fcc metals and applied the analysis to crystals undergoing axisymmetric flow, which approximates the shape change of an embedded grain in a polycrystalline aggregate deformed in tension (or compression). For the twelve equivalent (111) (110) slip systems, there are 384 independent combinations of five slip systems that satisfy the imposed strain.&apos; Taylor laboriously calculated the value of M = ZjIyj /E for each combination (although some were missed) and obtained the minimum M, hence the active combination, for a number of axial orientations distributed throughout the stereographic triangle. (yj is shear from slip on the th system and e is the tensile strain). Detailed contours of constant minimum M were recently obtained by Hosford and Backofen using a simplified but equivalent Bishop and ill&apos; analysis. Due to the numerous combinations of slip systems involved in the calculations, however, the full potential of the powerful Taylor analysis has not been exploited. For this reason, we have recently utilized techniques of linear programming to obtain solutions of the Taylor analysis for axisymmetric flow, for slip on {110)(< 111), {112)(111), and {123)(111) systems as well as mixed slip composed of these three systems. These slip modes are of obvious importance in the deformation of bcc crystals. Some of the salient results are summarized below. 1) Stress-Strain Data for Polycrystal. The value of M averaged over all axial orientations is the ratio of the tensile flow strength of a randomly oriented aggregate to the critical resolved shear stress for slip. This value enters importantly in theoretical deductions of the polycrystalline stress-strain curve from single-crystal data.2&apos;3&apos;5 Table I lists the values of Ma,, for the several cases of slip, as obtained by the present computer work. 2) Texture Hardening. Since the value of M depends on the axial orientation, the (tensile) flow strength of a specimen may be increased through texture control.&apos; An example of the computer results is shown in Fig. 1, where contours of minimum M have been computer-plotted for the case of mixed slip on {110}(111), {112)(111),and {123}(11 1) systems. It may be seen that, under axisymmetric flow, wires of (111) and (110) axial orientations are 50 pct stronger than those oriented at (100) .

Jan 1, 1968

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550&apos;F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By M. F. Hawkes

Austenite grain size has long been recognized by metallurgists as an important property of steels because of its influence on toughness, hardenability, ma-chinability and creep strength. Much research has been carried out on wrought steels to develop methods for disclosing austenite grain size, and to, provide knowledge of the grain-size characteristics of steels produced and heat-treated in various ways. Much less work in these fields has been done on steel castings; partly because, owing to the variable and complex microstruc-tures of cast steels, it is frequently very difficult to obtain results that are not questionable. The object of this investigation, therefore, was to establish, for a wide variety of carbon and alloy cast steels, suitable methods for disclosing austenite grain size and some knowledge of the grain-size variations to be expected. The steel foundryman is interested in austenite grain size at two different stages in the manufacture of his products; one is just after the steel is cast, and the other is after any reheating operation carried out above the critical temperature range. In both, it must always be kept in mind that the grain size being sought is actually a previous austenite grain size, and that the austenite no longer exists once the steel has cooled to room temperature. The prob-lem of the investigator is always to use evidence obtained from the structure at room temperature to deduce this previous austenite grain size, which was established the last time the steel existed at a temperature above the critical range. Since most steel castings today are at least annealed or normalized, the measurement of austenite grain size established by heat-treatment will he considered first. More than 50 commercially produced cast steels rcpresenting a wide variety of compositions and melting practices were used in the study. For each steel, grain-size determinations were made after each of three widely varying heat-treating schedules namely, one hour at I550&apos;F, one hour at I700°F, and six hours at 1700 F. The list of steels and results obtained on them will be found in the appendix. (See page 530.) A discussion of the knowledge gained on the applicability of various test methods and on grain-size characteristics of cast steels in general follows. MEASUREMENT OF AUSTENITE GRAIN SIZE ESTABLISHED BY HEAT TREATMENT Methods Suitable foR Determining Austenite Grain Size after Heat-treatment at Ordinary Temperatures and Times It was desired, as one of the results of this investigation, to be able to recommend to steel foundries a method, or methods, of disclosing grain size best suited to accurate

Jan 1, 1948

By R. J. Schilthuis

In 1929, Coleman, Wilde, and Moore1 undertook an investigation of the theoretical decline in reservoir pressure as related to the production of oil and gas. The most important part of this work was presented in an equation defining the relationship between the reservoir pressure, the quantities of oil and gas produced, the oil and gas content of the reservoir, and the properties of the reservoir fluids. With this equation, it appeared that, with sufficient data, it would be possible to calculate the oil content of the reservoir and predict quantitatively the effect of gas-oil ratio on the decline of reservoir pressure. Needless to say, such an expression would be highly important in evaluating fields and in arriving at a choice of production methods to be used. Unfortunately, at the time these investigators published their work, there were not sufficient data available to permit application of the equation. The technique of measuring reservoir pressures had not been developed, gas measurements were uncommon, oil and water production records were in most cases inadequate, and little was known of the properties of the complex hydrocarbon mixtures making up the oil and gas in the reservoirs. For these reasons, little additional work of a similar nature could be done. However, during the past four years many data have been systematically accumulated on reservoir pressures and the properties of oil and gas, and it is now possible to use these data in furthering the studies on the behavior of oil and gas reservoirs. It is the purpose here: first, to present the derivation of a modified form of the equation given by Coleman, Wilde and Moore, which will permit the calculation of what later will be defined as the "active oil" content of a reservoir; second, to derive formulas for calculating the reservoir-energy changes that occur during the course of production, and finally, to discuss the limitations and application of the equations developed.

Jan 1, 1936

By R. J. Schilthuis

In 1929, Coleman, Wilde, and Moore1 undertook an investigation of the theoretical decline in reservoir pressure as related to the production of oil and gas. The most important part of this work was presented in an equation defining the relationship between the reservoir pressure, the quantities of oil and gas produced, the oil and gas content of the reservoir, and the properties of the reservoir fluids. With this equation, it appeared that, with sufficient data, it would be possible to calculate the oil content of the reservoir and predict quantitatively the effect of gas-oil ratio on the decline of reservoir pressure. Needless to say, such an expression would be highly important in evaluating fields and in arriving at a choice of production methods to be used. Unfortunately, at the time these investigators published their work, there were not sufficient data available to permit application of the equation. The technique of measuring reservoir pressures had not been developed, gas measurements were uncommon, oil and water production records were in most cases inadequate, and little was known of the properties of the complex hydrocarbon mixtures making up the oil and gas in the reservoirs. For these reasons, little additional work of a similar nature could be done. However, during the past four years many data have been systematically accumulated on reservoir pressures and the properties of oil and gas, and it is now possible to use these data in furthering the studies on the behavior of oil and gas reservoirs. It is the purpose here: first, to present the derivation of a modified form of the equation given by Coleman, Wilde and Moore, which will permit the calculation of what later will be defined as the "active oil" content of a reservoir; second, to derive formulas for calculating the reservoir-energy changes that occur during the course of production, and finally, to discuss the limitations and application of the equations developed.

Jan 1, 1936

By A. P. Herring, S. F. Ravitz

Manganese dioxide reacts with sulfur dioxide solution in the absence of oxygen to form manganous ion and dithionate ion, together with a small amount of sulfate ion. The effects of SO, concentration, hydrogen ion concentration, stirring speed, and temperature on the rate of the reaction were studied. If it is assumed that undissociated SO2 molecules react rapidly with MnO, at active surface sites and that bisulfite ions react slowly, an equation can be derived that satisfactorily represents the observed reaction rates. For solutions in which the reaction with undissociated SO2 predominates, reaction rates and activation energies estimated from diffusion theory agree well with those found experimentally. Manganese dioxide dissolves readily in aqueous solutions of sulfur dioxide. The nature of the dissolution reaction was first investigated by Gay-Lussac and welter1 in 1819; they identified a new oxysulfur radical, the dithionate ion, S2O6, as one of the reaction products. Since then, the reaction has become a standard method of preparing dithionates in the laboratory and one of the more promising methods of leaching manganese from low-grade ores. In the "dithionate process" developed by the U.S. Bureau of Mines2,3, manganese-dioxide ore is suspended in a solution of calcium dithionate and leached with gas containing sulfur dioxide. The manganese is dissolved and the sulfur dioxide is oxidized according to the reactions:

Jan 1, 1965

By Ronald C. Koo

THE effect of grain size on the mechanical properties of the bcc metals has been a subject of intensive theoretical and experimental study.&apos;-l5 Quantitative relationships have been established experimentally between yield stress and grain size and between the ductile-brittle transition temperature and grain size in a number of metals.6"15 Much significance has therefore been attached theoretically to the grain size dependence. In all these experiments, different grain sizes were always achieved by annealing specimens at various temperatures. The implicit assumption was that any change in the dislocation substructure or in the distribution of impurities which might occur simultaneously with the production of various grain sizes had only a negligible effect on the mechanical properties. The validity of this assumption, however, is questionable. transformation in iron-nickel alloys is actually an extraneous phenomenon due to inadvertent compositional changes in the martensite if the heating rate is not sufficiently rapid. This complication can be avoided by up-quenching for the reversal treatment,5 and then the stabilization does not appear. Clearly, the lattice imperfections and strengthening produced by the reverse transformation are not responsible for the marked stabilization which has been observed by other investigators in these alloys. Data will be presented in this note to show that, at least in recrystallized tungsten of commercial purity, the difference in the ductile-brittle transition temperature of specimens annealed at various temperatures is more a result of a variation in the distribution of impurities rather than of the difference in grain size produced by the anneal. Ductile-brittle transition temperatures in tension were determined on powder-metallurgy tungsten specimens recrystallized at various temperatures. Tensile specimens having a gage length of 1.50 in. and gage diam of 0.18 in. were recrystallized at 1450°, 2000°, 2350°, 2550°, 2750°, or 2800" for 30 min in a vacuum furnace at a pressure of 1 x 10"5 mm of Hg and then tested at a constant extension rate of 8 x 10 per sec in an argon atmosphere from 100" to 800". Typical quantitative analyses of impurities are given in the Table. These results show that, within the precision of the analyses, see Table, annealing did not result in any detectable change in the impurity contents of the specimens, nor was there any detectable difference in purity between specimens having large differences in grain size annealed at the same temperatures . The results of the tensile tests yielded three distinct ductile-brittle transition curves approximately 225&apos; apart. As shown in Fig. 1, data of specimens annealed at 1450°C and those of specimens annealed at 2000°C (O) fell on Curve A. Data of specimens annealed at 2350" and 2550°C fell on Curve B, and those of specimens annealed at 2750" and 2800°C fell on Curve C. The decrease in ductility with increase in annealing temperature became so pronounced that one third of the specimens annealed at 2750" and two thirds of the specimens

Jan 1, 1963

By H. R. Ogden, E. S. Bartlett, A. G. Imgram

THE tensile and notch tensile ductile-to-brittle transition characteristics of several refractory metals and alloys have been well documented.1-3 Electron-beam melted tantalum and columbium have been shown to retain excellent ductility at very low temperatures. Some indications of brittle behavior (low ductility and cleavage fracture) were observed with columbium tested at -253oC, but no similar effects were noticed with tantalum. Increasing the interstitial oxygen content in these two materials resulted in the detection of indications of brittle behavior at higher temperatures, although good ductility was retained in both bases at -196°C when they contained about 1 at. pet 0. Detailed descriptions of the impact transition behavior of these two materials at various purity levels have not been available. This technical note describes the effect of interstitial oxygen on the impact properties of wrought, fibered tantalum and columbium and compares the transition behavior to the previously determined tensile transition characteristics. Tantalum and columbium impact specimens with three different interstitial oxygen levels indicated in Table I were tested at temperatures ranging from -196o to 300°C. Oxygen additions were made to 1/2-in.-diam bars of electron-beam melted material in a Seiverts Apparatus. The oxygenated bars were then homogenization-annealed to obtain uniform cross-section hardnesses and swaged to

Jan 1, 1964

By N. A. D. Parlee, E. M. Sacris

OVER 55 years ago, Sieverts and Hagenacker1 and Donnan and shaw2 made determinations of the solubility of oxygen in liquid silver, over a rather short range of temperatures (973° to 1125°C), using quartz bulbs, mainly at 1 atm. From the results of their investigations, Mizikar, Grace, and parlee3 plotted % O vs 1/T and obtained the following straight-line equation for solubility at 1 atm: log % O = 723.7/T - 1.0949 Recent work on the kinetics of the Ag-O2 system394 indicated there might have been some error due to reaction with the direct heated silica bulbs. Thus it became important to redetermine the solubility with the silver contained in a better refractory such as alumina, and by induction heating where the walls of the container were not so strongly heated. It was also desirable to extend the temperature range. A modified Sieverts apparatus of fairly standard type was used except that a special type of reaction tube was employed, Fig. 1. Dried argon with a guaranteed purity of 99.9 pet, and dried medical-grade oxygen with a guaranteed purity of 99.6 pet containing a little nitrogen, were the gases used. The measuring system consisted essentially of a manometer and a water-jacketed 100-cc gas buret with an open-end vertical tube parallel to the buret. This tube has the same diameter as the buret in order to give the same capillary effect on the mercury. A screw leveling device was used with the buret leveling bulb to help provide accurate pressure readings. A 2-mm ID capillary line connected the buret to the reaction chamber, helping to reduce the dead volume, which was determined with argon. The heating medium was a 2.5-kw output induction furnace. The induction coil was made of a 3/16-in. copper tubing with eight turns and an inside diameter of 4 cm. The reaction bulb was made of a quartz tube 18 cm long and 3 cm in inside diameter, Fig. 1. Inside the quartz tube were two alumina crucibles (Mor-ganite Triangle RR, XN10 and XN5) one inside the other. Below these two was an alumina disk. The disk prevented the corners of the outer crucible from expanding against the quartz tube. The solid sample (99.994 + pet Ag), which had been previously cleaned by air oxidation and repeated removal of scum, was placed inside the inner crucible. An alumina disk with a hole at the center covered the two crucibles. In order to decrease the dead volume, an evacuated quartz "filler" tube was placed on top of the crucible cover. The part of the reaction tube above the spherical joint was made up of Pyrex glass with a flat glass top. It was here that a prism was placed to facilitate the use of an optical pyrometer, previously calibrated at the freezing point of silver. This type of reaction bulb and furnace assembly was specially designed for this work, and used in preference to the relatively new water-

Jan 1, 1965

By Thomas C. Patton, Eric S. Cheney

L-D gold mine is 3 miles south of Wenatchee, central Washington. Recognition of locally mappable conglomerates, sandstones, and shales within the Paleocene (?) Swauk formation led to the discovery that the known epithermal gold mineraliza¬tion is limited to a previously unknown imbricate thrust zone of unknown displace¬ment cutting the open folds o f the area. Hypabyssal intrusions also are most nu¬merous along the trace of the thrust faults. Yakima basalt of Miocene age uncon¬formably overlies the Swauk formation, thrust faults, and the intrusions. The L-D mine is in a northwesterly trending imbricate fault block of nearly vertical strata. Microscopic native gold, electrum, and naumannite occur in quartz veins and as low¬grade disseminations in the well-silicified portions of arkosic sandstones. Fault gouge on the "footwall fissure" limits ore to the hanging-wall block of the fault. Epithermal mineralization and alteration are spatially related to the nearby intrusions. Right lateral north-south faults offset the ore a maximum of 300-400 ft along any one fault. From 1949 until January 1967, when the L-D mine closed, 1,036,572 dry tons of ore valued at $14,962,305 and averaging 0.396 oz Au per ton and 0.607 oz Ag per ton were mined. Recognition of the structural control of the mineralization and altera¬tion within the Swauk formation suggests several areas within and outside of the mine that warrant further exploration. For example, the high-angle faults, imbricate thrusts, and the intrusions of this area are on strike with similar features along the major Entiat fault zone 10 miles to the northwest. The L-D gold mine (previously called Squilchuck, Wenatchee, Golden King, Gold King, and Lovitt) is located in Squilchuck Canyon about three miles south of Wenatchee, Chelan County, Wash. (Fig. 1) on the eastern edge of the Cascade Mountains. The major stratigraphic unit in the area is the nonmarine early Tertiary Swauk formation, which is predominantly com¬posed of arkosic sandstone. The lack of laterally per¬sistent units and the paucity of outcrops heretofore have precluded all but the grossest subdivision of the Swauk.&apos; As a result, the true significance of the open folds in the Wenatchee area was not recognized, and although the geology within the mine was known, the structural setting of the mine was virtually unknown. During the present investigation, several locally map¬pable units were discovered within the Swauk which, in conjunction with mine maps, indicate an imbricate thrust zone. The epithermal gold mineralization, most of the hypabyssal intrusions, and the zones of hydrother¬mal alteration are located within or near this thrust zone. The purpose of this paper is to: (1) to describe this structural setting, rather than the detailed mine geology already presented by Lovitt and Skerl,2 and (2) to sug¬gest that from an exploration standpoint, this struc¬tural setting may be repeated in areas inside and outside of the mine area. Stratigraphy and Structure of the Swauk Formation General: The Swauk formation contains three distinct lithologies. Typical Swauk sandstone is gray on fresh surfaces, poorly sorted, weathers tan, and is cross¬bedded; it consists of 40-60% quartz, 20-40% feldspar, and up to 10% muscovite and biotite 9 The typical shale is gray to dark brown, very soft, and interbedded with silty sandstones; sharp contacts exist between the

Jan 1, 1972

By James Kemp

PostScript to a paper presented at the New York meeting, February, 1915, and printed in Bulletin No. 98, February, 1915, pp. 129 to 154. The writer looked over the quarry with care in the search for fossils, having in mind shells or corals of fairly large size. In the brilliant summer sunshine, none were observed on the glaring white ledges. The impression was gained that none were present and the statement to this effect was made in the edition of this paper published in the Bulletin&apos; of the Institute for February, 1915, p. 136. On closer examination in the laboratory it has been discovered that the limestone itself is made up of minute organisms, which are clearly revealed by microscopic examination of thin sections. The principal component of the rock is a small foraminifer, 0.1 to 0.3 in. (2.5 to 7 mm.), of the genus Orbitoides, presumably an Oligocenic form. Figs. 1 and 2. illustrate it. The accompanying description has been kindly summarized by Marjorie O&apos;Connell, M. A., Curator in Paleontology in Columbia University, who first detected the evidences of organisms in the rock. Orbitoides kempi O&apos;CONNELL N. SP.1 The foraminiferan which makes up the Seboruco limestone is an Orbitoides of a Species new to North America. The only Orbitoides heretofore described from this country is 0. mantelli from the lower Oligocenic of the Gulf States. This form from Cuba, then, so different in all of its characteristics from the 0. mantelli, is of great interest as perhaps forming a basis of correlation over wide areas. The most closely related Species is 0. dispansa Sowerby, which occurs in the Nummulite limestone of the Eocenic of the Bavarian . Alps, in the Priabona beds of the lower Oligocenic of Massano, and elsewhere in Italy, as described by Gümbel.2 The age of the limestone in Cuba would thus Seem to be of upper Eocenic or lower Oligocenic age, probably the latter. The fossil has the form of a sphere Surrounded by a wavy rim of horizontal extent, the whole resembling two flat-brimmed, round-crowned hats placed base to base. The total extent of the Shell ranges up to 7+ mm., while the thickness of the central sphere is 2.5 mm. in one of the largest individuals. Like all of the other Species of Orbitoides, this form begins with a Single layer of chambers which multiply in one plane and assume a circular outline; but it is in the subsequent growth that the distinguishing specific characters appear, for the chambers at the central portion of the shell increase more rapidly than do those near the periphery and in consequence a Swelling is produced which finally gives the Spherical form which is so characteristic. The rim, on the other hand, shows little chamber-increase and remains thin. This is clearly Shown in the sections figured, where the central row of larger chambers forms the equatorial zone. Radiating from this row, in section, there appear, a number of solid cones alternating with broad reticulated ones. The solid cones mark the more dense structure forming the walls surrounding the reticulated or chambered cones. These appear upon the Surface as distinct pits, whereas the solid part appears as raised walls.

Jan 7, 1915

By Ottey M. Bishop, William G. Peryam, Fred E. Johnson

THE Lepanto Consolidated Mining Company is the largest copper producer in the Philippines, and the only one that makes a concentrate valuable principally for its copper; also, it has the only productive copper mine situated at considerable distance from the sea, and is the only one in the islands operating its own smelter. The Lepanto mine is in the Municipal District of Mankayan, sub-province of Benguet, near the heart of the Mountain Province of Northern Luzon. It is 165 km. from its shipping point at San Fernando, Province of La Union, on the shore of the China Sea. Elevations at the property range from 3200 to 4500 ft. The climate is very mild; temperatures are seldom below 50° or above 80°F. Annual rainfall approaches 170 in. and is mainly confined to a rainy season lasting from May to October. The months from December to April, inclusive, are usually extremely dry. This climatic pecularity entails the problems of landslides on the roads during the rainy season and water shortage during the dry season. The Mountain Trail, an improved rocksurfaced toll road maintained by the Commonwealth Government, gives access to the property. The 105 km. over this road may be traveled in about 4 ½ hr. during the dry season. Very few sections of the road are straight for more than 100 meters, and about one third of it is a one-way road controlled by gates. All freight for the property is delivered by the Manila Railroad Company to Bauang, La Union, 45 km. west of Baguio and at sea level, where it is picked up by freight trucks and hauled via Baguio to Lepanto. Granulated matte is hauled in bulk from Lepanto in four-ton lots on freight trucks to the storage bins at San Fernando. Freight rates from Bauang to the property amount to [P]8.oo per ton, and from the property to San Fernando the rate is [P]16.00 per ton. The company pays the road toll, [P] 1.00 per truck, each way. THE CAMP The company maintains a modern camp, well separated from the mine and reduction plant. Comfortable and sanitary living quarters, water, and light, as well as free medical service are provided all employees. A hospital staffed by a doctor and two nurses takes care of all medical treatment. Considering recreational facilities of great importance, the company has provided two tennis courts, two basketball courts, and badminton courts for employees. Bowling alleys and a motion picture theater are operated by the company, the profits being expended for other recreational purposes. A moderate sized recreation hall serves for barrio dances, meetings,

Jan 1, 1942

By E. R. Parker, D. L. Martin

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By D. L. Martin, E. R. Parker

In a previous paper one of the authors observed that the rate of cooling from the anneal prior to testing greatly influenced the life of copper under sustained load at 200°C. Furnace-cooled bars of oxygen-free copper (with and without silver) had a life four to twenty-five times that of the water-quenched specimens. The addition of 0.054 per cent silver to the oxygen-free copper increased the life at a stress of 20,000 lb. per sq. in. from about 2 hr. to 50 hr. Fractures in these bars were intercrystalline. An explanation was advanced to account for the profound influence of cooling rate on the rupture properties at 200°C. The suggestion offered was that at the high annealing temperature the minor constituents are distributed at random. By water quenching, this condition is maintained at room temperature, whereas furnace cooling permits some segregation at the grain boundaries. The higher concentration of the minor constituents in the grain boundaries results in a. strengthening, so that a longer life at a given stress and .temperature results. Small amounts of cadmium or manganese have also been found to increase the life of copper at 200°C., and to a much greater extent than silver.2 The increase in the long-time strength of copper resulting from small additions of cadmium or silver appears to be related, indirectly at least, to the higher softening temperatures of such alloys. The elements, such as silver or cadmium, which greatly increase the rupture life of copper also cause large increases in the softening temperature. As little as 0.05 per cent of cadmium or silver is sufficient to raise the softening temperature more than 100°.3,4 The effects of cooling rate and of minor constituents on the rupture properties are of considerable fundamental as well as practical interest; therefore a more detailed study of their nature was conducted and is reported in this paper. Experimental Procedure Materials The materials studied in this investigation may conveniently be classified in two groups: one consisting of a wide variety of commercial coppers, and the other composed of special high-purity, laboratory-prepared coppers. The commercial materials were tested to determine whether or not the effect of cooling rate occurred with all coppers, whereas the high-purity coppers were investigated in order to establish a basis for evaluating the effect of minor constituents on the rupture properties. In Table I are given the analyses of the coppers tested. The samples I to 6 are commercial materials and were obtained for the most part from stock supplies.*

Jan 1, 1944

By H. B. Treweek, V. R. Degner

Current mineral industry trends toward handling the high tonnages of lower grade ore and tailings retreat lead to a continuing need for large volume flotation cells. The benefits which accompany the larger cell flotation circuit include reduced capital cost, less mill floor space, reduced operational complexity, and less maintenance, provided the metallurgical performance and solids suspension capability of the cell are not compromised. This study reviews development considerations pertinent to large mechanical air induction type flotation cells from the standpoint of cell internal hydrodynamic characteristics and metallurgical performance. While the importance of process related factors such as chemical usage, pH control, solids size and loading, and circuit arrangement cannot be denied, this study will emphasize the relationship of cell size (volume), mechanism geometry (impeller diameter), and mechanism operating conditions (rotor speed and submergence), to air transfer, liquid circulation, liquid "rise velocity" and mechanism power draw. Specific hydraulic performance maps for large capacity 300 and 500 cu ft flotation cells will be reviewed in terms of the relationship between the operational variables and the air and liquid flow conditions within the cell. Metallurgical results, obtained under plant operating conditions for 300 and 500 cu ft cells, are included to illustrate the metallurgical performance similarity of flotation cells which follow hydrodynamic scale-up criteria set forth in this investigation.

Jan 1, 1976

By C. D. Ramsden

DURING the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Pur¬chase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by sal¬vaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a con¬siderable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been re¬building locomotive wheels for several years with automatic open arc-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under¬flux arc-welding process for wheel rebuild¬ing, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company&apos;s maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company&apos;s heavy locomotives have three- sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. OPEN ARC WELDING With the open arc process, a set of wheels could be rebuilt for about 40 pct of the cost of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or posi¬tioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1946