Search Documents

By George Boulter

Draglines 8.2-1 Introduction. The nature and characteristics of rock and rock derivatives forming the crust of the earth vary so greatly from place to place that it is impossible to use the same numerical factors to show the, productive ability of excavating equipment on different jobs or projects. Factors for each project must be developed individually and applied as the conditions and requirements dictate. TYPES' OF DRAGLINES. Types of draglines are differentiated by the propelling method used and are generally divided into four classes, as follows: 1. Wagon mounted 3. Crawler mounted 2. Truck mounted 4. Walking Figure 8.2-1 shows a truck-mounted dragline. This type is considered to be the most mobile unit. In order to increase stability over the side, outriggers are installed as part of the truck chassis. This feature is not shown in .this figure. Figure 8.2-2 shows a crawler-mounted dragline. The long, wide crawlers are used to increase the stability and reduce the bearing pressure of this unit. These features allow for use of these units on surfaces too soft for the wagon- or truck-mounted types. Figure 8.2-3 shows a walking-type dragline. The large diameter tub and the well-supported boom through the gantry gives high stability for rugged works over a long life. BASIC PARTS OF A DRAGLINE. The basic parts of a dragline are illustrated in Fig. 8.2-4. A deck layout is shown in Fig. 8.2-5 with the main components named. OPERATION OF A DRAGLINE. Following is a description of the steps and controls present in a typical cycle of operation of a large dragline having independent hoist and drag motors. Starting the cycle with positioning the bucket on the ground under the point of the boom, the next step is

Jan 1, 1968

Jan 1, 1947

By B. H. Caudle, M. D. Witte

In predicting the performance of a pattern injection operation, the engineer needs to know both the amount of oil to be recovered and the rate at which the recovcry will take place. This paper- describes fluid flow model studies on the effect of mobility ratio on the rate of oil recovery in a five-spot. The results show the change in fluid conductivity (total flow rate/pressure drop) as the sweep-ont pattern increases for mobility ratios between 0.1 (and 10. There data, when cornbitted with a knowledge of reservoir permeabilities and sweep-orit pattern efficiencies, cata he used to predict the cLrmulntivr oil production as a function of time for homogeneous five-spot injection systems. INTRODUCTION The flow potential in a pattern flood element is a function of the mobility ratio and how far the injected flood front has gone.1,2 For a waterflood project having a mobility ratio of one, the conductance—which is the flow rate per unit pressure drop (q/Ap)—-will remain the same throughout the life of the flood. If the mobility ratio is favorable ( < I), the conductance of the project will drop continuously throughout the operation. If, on the other hand, the mobility ratio is unfavorahlc. the conductance ratio will increase continuously. Therefore, if the reservoir engineer wishes to predict either the rate at a specified pressure or the pressure at some rate for a secondary recovery project, he must know how the conductance will vary during the flood. Other investigators have studied this problem using potentiometric models&apos; or analytical solution&apos;. The

By Frank C. Kelton

A method is outlined for the analysis of large cores, developed primarily for the purpose of obtaining reliable data on fractured or vugular limestones. Porosity and fluid saturations are determined by a modified Dean-Stark extraction after initially bringing the samples to 100 per cent liquid saturation by a vacuum-pressure method. Horizontal permeabilities on the whole samples are determined in two directions, parallel and perpendicular to the di-rection of principal fracturing. Results are presented for various types of formations. A comparison is made between data obtained by this special method and the method of conventional analysis, and discussion is given of the relative advantages and limitations of each. In view of this comparison a modified method for the analysis of fractured and vugular formations is proposed, which method retains the advantages of the previously outlined techniques but gives promise of speeding up the analysis. INTRODUCTION For many years the greater part of the production in the Permian Basin was from formations of Permian and Pennsylvanian age. While production from these formations is still the predominant production. deeper prospecting has brought to light older formations with oil productive characteristics. Attempts to core these deeper horizons were at first usually characterized by poor recovery. The old rule of thumb, "good core recovery — poor well" was originated and remained in effect until recently. With the advent of diamond coring and the increased efficiency in drilling and coring operations. the old adage has lost its significance. Formations of Devonian. Silurian and Ordo-vician ages were successfully cored with varying degrees of recovery. The cores thus obtained were surprising and in some case; disappointing. Good recovery from these formations led to speculation as to the feasibility of analysis and the meaning of data obtained from conventional analysis. Commercial laboratories were engaged to analyze these cores. and their results indicated that data obtained by conventional methods would be of little value. From visual inspection it was apparent that in many cases the effective porosity for storage of hydrocarbons. and permeability. were contained largely in fractures and solution cavities rather than in the primary crystalline structure of the formation. In other cases the solution cavities augmented the effective porosity of the primary crystalline structure, or fractures enhanced the permeabiilty of the latter so that the formation might respond favorably to acidization and become commercially productive. Since the spacing of the cavities and fractures was often comparable to the core diameter, it was evident that the entire core should he analyzed instead of small fragments. On the basis of these observations, commercial laboratories were requested to devise a system of analysis which would yield data of practical value. Pro- cedures have accordingly been developed which seem to meet this requirement, and to date nearly 12,000 large core samples have been analyzed. It is the purpose of this paper to describe the methods used, to present typical results for several fractured formations and to compare the data obtained by this special analysis with that obtained by conventional analysis. Certain modifications and alternative procedures are finally suggested to speed up the analysis. CORE ANALYSIS PROCEDURE Fluid Saturations and Porosity The core sample, in segments up to 15 in. in length. is marked, weighed and examined under ultra-violet light to determine the presence of oil saturation. If present, the approximate quantity of oil and its location on intercrystalline, fracture or vugular surfaces is noted. This information is carefully recorded. The degree of fracturing and/or vugular development is also noted. The sample is then placed in a pressure cell and the air evacuated with a high speed vacuum pump. This evacuation is continued only long enough to reduce the pressure to approximately the vapor pressure of water in order not to remove excessive amounts of water. Water is admitted to the cell and allowed to penetrate the sample under atmospheric pressure, filling the pore space initially occupied by air and replacing the small amount of water removed by evacuation. Pressure up to 200 psi is applied to force water into the smaller capillaries, and the sample is left sub-

Jan 1, 1950

By Robert D. Pehlke, Arden L. Bement

A mass transfer coefficient for the removal of hydrogen from liquid aluminum by inert flush degassing has been determined experimentally at 700°C. A mathematical model has been derived, assuming transport control, which adequately describes the experimental data. The removal of hydrogen is shown to increase with decreasing bubble size, and with increasing flow of flushing gas. The presence of hydrogen in liquid metals in amounts which exceed the solid solubility at one atmosphere hydrogen pressure is highly undesirable, causing unsound ingots or castings, or resulting in difficulties during further fabrication. The removal of hydrogen from liquid metals can be accomplished by several methods, the principal two being vacuum treating and inert flush degassing. The design of a process involving either of these techniques is based on the mass transfer coefficient for hydrogen between the liquid metal and a hydrogen-dilute gas phase. In an effort to extend our knowledge in this area, an investigation of the rate of removal of hydrogen from liquid metals by inert gas flushing was undertaken. In view of the difficulties encountered with gas porosity in the casting of aluminum and aluminum alloys, and because of certain experimental advantages, liquid aluminum was selected for the study. PREVIOUS INVESTIGATIONS The removal of gases from liquid metals, particularly steel, has received considerable attention in recent years, The first definitive work of a theoretical nature was presented by Geller1 who considered the case where equilibrium exists between purging gases and metal bath during flushing, and also deviations from this ideal case. Hulme2 has surveyed a number of experimental studies and discussed some of the practical limitations of removing dissolved gases from molten metals. More recently a number of studies have been reported on degassing of steel melts by flushing with an inert gas.3&apos;4 Considerable work has also been reported on aqueous and organic liquid-gas systems, and an excellent summary prepared by Hovis.5 The treatment of liquid aluminum by a flushing gas to remove dissolved hydrogen has been known for several decades.6 A number of gases have been used for this purpose, including nitrogen, argon, and chlorine, or mixtures of these gases. Tikkanen and Erkko7 have studied the relative density changes of aluminum castings poured from melts degassed with chlorine, nitrogen, and mixtures of the two gases. Their

Jan 1, 1962

By T. A. Read, H. K. Birnbaum

STRESS-induced twin boundary motion in the AuCd ß&apos;phase (52.5 at. pct Au 47.5 at. pct Cd having an orthorhombic structure (space group D h)&apos; was discussed for the case of transformation twins.&apos; Mechanical twinning, i.e., introduction of new twin orientations by the applied stress was sometimes observed in the ß&apos; phase which contained two transformation twin orientations. (See Ref. 2 for experimental details.) The transformation twins terminated at the mechanical twin boundary; the two initial orientations having been twinned to the new orientation as shown in Fig. l. In a "hard" tensile instrument, formation of each mechanical twin was accompanied by a sharp drop in load (and an audible click) resulting in a typical serrated load-extension curve. The mechanical twins increased in width and additional twins were nucleated as the load increased until the entire specimen was occupied by the mechanical twin orientation. A restoring force2 caused the mechanical twin and transformation twin boundaries to return towards their initial configuration on releasing the load. In a stabilized specimen* the total strain introduced by mechanical twinning was recovered on releasing the applied stress. Initial and final microstructures were identical. After decreasing gradually to a critical width, mechanical twins suddenly disappeared accompanied by audible clicks and sharp increases in load (measured at a constant rate of crosshead motion in a "hard" machine). Mechanical twins could be stabilized in any position by maintaining the applied load for a sufficient time, indicating a decrease in restoring force with time similar to that observed for transformation twins.&apos; Orientation relationships for mechanical and transformation twins were determined and are shown in Fig. 2. The mechanical twin, T3, was twin related to transformation twin, T,, by reflection in (1ll), and twin related to transformation twin, T2, by reflection in (111)T, . T, was related to T, by reflection in(ll1)T1 . The "average" mechanical twin composition plane lay several degrees from (1ll), . In every specimen which mechanically twinned, orientation T3 was most highly favored by the applied stress, i.e., it was the twin orientation which provided the greatest change in length compatible with the direction of applied stress

Jan 1, 1961

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate&apos;s lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By E. C. Wright

The following article is based on observation of college graduates entering the steel industry in technical work made during the Past 25 Years, the first five of which were spent as a college instructor in two engineering schools, and the last 20 in the employ of a large steel company that has hired hundreds of engineering graduates for steel-mill operations. The college graduates encountered during this period have come from many colleges representing schools in Eastern States, Midwestern Universities, many Southern colleges, and many smaller colleges and normal training schools mostly in western Pennsylvania and Ohio. The college training of these students for engineering work naturally has varied widely and the educational qualifications of the entrants have been in many ways different. It was found at an early date that graduates of standard engineering colleges were much more adaptable than graduates in science from nontechnical schools. The engineering students seemed to be more suited to actual work in steel plants and in general were better able to grasp a knowledge of the operations they observed. However, although the graduates of engineering schools have had somewhat better training in physics, mathematics, and engineering, it has been a general and continual observation that most of the students employed have had inadequate training in the fundamental sciences. Since this discussion relates entirely to metallurgical engineers it should be emphasized that students taking metallurgical engineering courses in college seem to be poorly trained in organic chemistry-physics, physical chemistry, thermodynamics, and any higher form of mathematics than simple calculus. It has been noted frequently that young engineers faced with problems in a mill that involve some mathematics generally flounder badly, and that they have little conception of physical chemistry. Another common deficiency lies in the young graduate&apos;s lack of knowledge of where to look for the more detailed literature on any subject. He reverts instinctively to some college textbook whose coverage is usually very elementary. It is recommended that such textbooks contain a bibliography of the source literature. and that students be taught to use the original data. Many of the students had had previous courses in college dealing with metallurgical work such as steel melting, metallograhy, etc.r but it was found that their grasp of these subjects was extremely sketchy. It was soon realized that an ordinary engineering graduate could be taught more about steel melting and manufacturing processes in a few weeks in a plant than he could learn in a college course on such subjects. A similar statement may be made regarding the ability of students to conduct laboratory work. Their lack of technique and skill in handling equipment and setting up experiments was soon apparent. It became neces-

Jan 1, 1948

By John E. Riddell

This review is based on a questionnaire sent out in 1959 to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geo-chemical techniques in Precambrian terrains. Of the companies questioned, 21 returned completed questionnaires and of these, 15 companies stated that they had some experience in this type of work. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only three have reported that they do not use applied geochemistry at all. The others have reported that they make use of applied geochemistry in New Brunswick and in the Cordillera in areas of light glaciation. Their opinion is that it is a useful aid when accompanied by other techniques in evaluating mineralized areas. GEOCHEMICAL SURVEYS Table I reviews the type of geochemical surveys used by these companies, and the following points of interest should be noted.

Jan 11, 1960

By R. L. Slobod, B. H. Caudle

In the past, the main emphasis in attacking the problem of the recovery of oil has been on the determination of fluid flow characteristics and residual oil saturation in the part of the reservoir which is contacted by a displacing phase. It is recognized that the determination of the fraction of the reservoir contacted in secondary recovery operations is also of great importance in predicting the ultimate recovery to be expected. A method is described in which radiographic techniques are used to determine these areal sweepout factors for any type of well spacing. Data showing the relationship of viscosity ratio and relative permeability to areal sweepout efficiency are presented for the five spot and the direct line drive well spacing patterns. Further applications of the method to studies of the displacement efficiency in the area contacted are mentioned. INTRODUCTION The problem of increasing oil recovery from typical reservoirs is generally attacked by trying to devise some means for reducing the residual oil in that part of the reservoir which is contacted. The fraction of the reservoir contacted in the displacement process. however, is also of major importance but has been given less consideration in the past. one reason for this neglect is the meager information available on the portion of the reservoir contacted and the magnitude of changes in this factor as operating conditions are varied. Until recently, the only means available for determining this quantity has involved the use of the electrolytic or poten-tiometric modelsl in which one is limited to working with a mobility ratio of unity. while means for calculating the volume of a reservoir contacted do exist. the calculations are very tedious for systems with mobility ratio different from unity. Recently several such determinations have been reported,213 and an experimental method involving a step-wise use of potentiometric models has been described.&apos; A new method which has been developed for studying the areal distribution of phases in a porous medium is discussed below. This tool can be&apos; used to determine the effect of operating variables such as viscosity, relative permeability, presence of gas, mobility ratio, rate and stratification on the fraction of the reservoir contacted by the displacing medium. This development based on the use of X-rays gives a pictorial representation of the location of the phases. Further, the amount of each phase at each point of interest can be determined quantitatively. X-RAY METHOD FOR AREAL STUDIES In this method the location of various phases distributed Over a test area are observed simultaneously by obtaining a photographic record of the transmission of X-rays through the test plate. This procedure is an adaptation of the radiographic techniques which have 10% been used in the medical and industrial fields. Just as the medical profession uses a chest plate to show spatial interrelationships, the location of an X-ray absorbing fluid and a nonabsorbing fluid in a porous medium can be determined by obtaining a photographic record of transmitted X-rays. Moreover, as changes occur in such a System, these changes can be observed by taking successive photographs. Previously, X-ray methods have been used in fluid flow studies to determine quantitatively the saturation at a given point in the system. The intensity of the transmitted X-rays was measured by an ionization chamber, so that a point by point survey of saturation could be made. In comparison with this earlier quantitative procedure, the photographic procedure which simultaneously observes the saturation at many

Jan 1, 1952

By H. Furman Byars

INTRODUCTION of bottom dump hauling units into the Ray, Ariz., stripping operation of the Isbell Construction Co., was motivated by several reasons, with what appears to be debatable results. The accepted theory of truck design for use in open-pit holds that end dump vehicles are the most adaptable for the work. But, because operations of the bottom dump, under certain construction and haulage conditions, proved economically feasible, the unit was put to work in the Ray copper pit. The decision to try bottom dump was reached after considerable observation of the unit in action on construction of earth filled dams, levees, airport construction and several other similar tasks. Basic tire design also motivated the choice. All things being equal, a vehicle running on low pressure single tires will outperform another operating on dual high pressure tires, providing load carrying capacities are the same. The investment required to equip a vehicle with four single tires to handle the same load as one with dual tires mounted on two axles and single front axles is about 60 pct greater. Thus, in order to reach the break even point on tire costs, single tires must operate 60 pct longer. Comparison is made with a truck outfitted with 10 16:00x25 tires. Two other factors were considered in selecting bottom dump trucks. It was felt the bottom dump principle would work well in dumping ore into a hopper where gate design fits this particular method. Also, with the absence of hydraulic dumping, ore pollution with oil is reduced. The mechanical simplicity of the unit also lent weight to its choice. Ordinary reasoning indicated maintenance costs would be low compared with other units carrying similar loads. The bottom dumping principle is not new. It dates back to the days when horses were used to haul the same kind of rig. The unit employed at Ray holds 25 cu yd struck measure, or approximately 42 short tons. Dumping is accomplished by releasing an air cylinder opening a dog holding the doors. Doors are closed by a cable system operating off a wheel wind deriving power by friction with the trailer tire. The unit is mounted on four 27.00x33 and two 14.00x24 tires on the front axle. The power unit is a 300 hp Cummins engine. Hydraulic power boosts the steering. A straight mechanical drive and friction clutch with 10 speeds is used. Conditions Not Ideal Top performance of the truck can be expected only under the conditions for which it was designed, in particular grades under 5 pct, handling fine material, and dumping where one thin layer can be placed on top of another. The machine will handle 42 tons per haul, operating at high speed, with only seconds used for dumping. On a 2 or 3 pct grade over a one mile haul,

Jan 1, 1952

By C. E. Shoenfelt

Jan 1, 1942

By C. E. Shoenfelt

Jan 1, 1942

By Cyril Stanley Smith, Earl W. Palmer

STRIP of any of the metals used for deep drawing operations occasionally yields cups that are defective because of a rim that varies in height around the cup in a wave-like manner Some such defects are traceable to tools or other press factors, but when the protuberances formed (usually four in number on brass and other copper alloys) are symmetrically disposed with respect to the rolling direction of the strip, they are invariably attributable to the metal The effect is known as "caring" and the protuberances are called "ears" Other terms frequently heard are "tips," "scallops," and "corners " It is recognized that the effect is most commonly a result of a directional crystal structure produced by rolling and annealing operations in the manufacture of the metal strip Numerous papers dealing with various aspects of the caring effect have appeared in the literature, those listed in the references&apos; being especially interesting and valuable An investigation of the factors influencing caring of brass cups has been in progress in the laboratories of the American Brass Co for several years, and it was thought desirable to make some of the results generally available in summarized form The present paper discusses many factors that do and do not contribute to ear formation In addition, a section is devoted to methods of minimizing the caring tendency of brass sheet by proper selection of the cold-rolling and annealing schedule by which it is produced In the space available, it is impossible to quote detailed experimental procedures and numerical results However, the authors make no statement that they do not believe to be properly substantiated, either by experimental evidence obtained under laboratory conditions or by experience in the actual production of deep-drawing brass in the brass mill MECHANISM OF EAR FORMATION It must be clearly understood that the formation on cups of symmetrical ears, four or more in number, is attributable solely to the strip metal, and results from the strip having different deformation characteristics in different directions The tools used in the drawing process, or the type and completeness of lubrication of the strip, have nothing to do with the problem of ears, although they do, of course, greatly affect the "drawing quality" of the strip and the general appearance of the cup A single tip may be drawn up on the rim of a cup because of misalignment of the tools, or because the gauge of metal varies from side to side of the strip The two-ear form that sometimes appears is also traceable to gauge variations However, the four-ear and six-ear symmetrical forms that we are concerned with here are caused by factors inherent in the structure of the metal itself

Jan 1, 1942

By H. Hansen, A. U. Seybolt, P. Yurcisin, B. W. Roberts

The Bi-Mn phase diagram in the region near BiMn was investigated, using principally thermal analysis and changes in magnetization with temperature. Of chief interest are the findings related to the magnetic transformation in Bi-Mn. THE Bi-Mn system is of both theoretical and practical interest because of the occurrence of the compound BiMn which exhibits unusual ferromagnetic properties. Because the Bi-Mn phase diagram reviewed by Hansen&apos; (see Fig. 1) in 1936 is based on work done by BekierY in 1914 and by Siebe" in 1919, which left considerable doubt about the nature of the diagram. it appeared desirable as an aid in understanding the alloying characteristics and magnetic behavior to examine the pertinent regions of the phase diagram. The most interesting reaction is the peritectic at 445°C which forms BiMn by the reaction: Liquid + Mn(sulfield) ? BiMn(sol field) There is also a eutectic at 262° C between pure bismuth and BiMn. Hansen draws in BiMn dotted, since in 1936 evidence for its existence was uncertain. Experimental Materials—Preparation of Alloys Electrolytic manganese of about 99.97 pet purity and bismuth of 99.99 + pet purity were used as starting materials.

Jan 1, 1957

A discussion at a joint meeting of the New York Section of the American Electrochemical Society and the American Institute of Mining Engineers, Nov. 20, 1913. Chairman Lawrence Addicks:-Our program this evening represents an attempt to set before you the present situation and outlook in the metallurgy of zinc. It is a time-honored custom to throw bricks at the zinc man. The accusation is that he has borrowed a lime kiln and a gas retort and part of a sulphuric acid plant, hitched them together, and spent the last 50 years in regarding with holy veneration the reactions which take place in that retort. The copper man, who thinks of zinc as something with which copper is adulterated to make brass, and the iron man, who regards it as a sort of paint for corrugated sheets, and the lead man, whose opinion as to zinc is not fit for publication, have long felt that, when two or three of the minor details of their respective metallurgies were put in order, they would take a few clays and fix up zinc on a modern basis. But somehow there still seem to be some unsolved problems at home, and while we are waiting it seems only fair that the case for the defense should be adequately presented. There is probably no man in this country to-clay better able to do this than Mr. George C. Stone, of the New Jersey Zinc Co., on whom I have pleasure in calling to talk to us on "Progress in the Metallurgy of Zinc." George C. Stone:-It is frequently stated that there has been no change in the metallurgy of zinc since the first Belgian furnaces were built in the early part of the last century. It is true there have been no such spectacular and radical changes as were worked in the metallurgy of copper and iron by the introduction of converters; but, in the essentials, I believe the progress in zinc metallurgy has been as great as in that of the other common metals. The main reason that there have not been revolutionary changes is that the chemistry of zinc differs radically from that of the other metals and these differences control the type of apparatus that can be used. The differences are: 1. The temperature at which zinc is reduced by carbon is much above the volatilizing point of the metal and it is therefore always produced as a vapor.

Jan 1, 1914

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.&apos; It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this&apos; paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By Chas Fettke

DURING the summer of 1916, while on a visit to the United States Agricultural Experiment Station at Mayaguez, Porto Rico, the writers were told by D. W. May, the director, that an occurrence of manganese ore had been reported from the mesa southeast of Mayaguez. A visit to the locality showed that the mesa is covered by a mantle of bright red soil resting upon serpentine. Here and there over its surface concretionary masses of limonite have been washed out of this soil. These were FIG. I.-MAYAGUEZ FROM NORTHWEST END OF MESA. apparently mistaken for manganese ore. On account of the similarity of this occurrence to the extensive iron deposits of northeastern Cuba, it was thought that a brief description based upon a two days&apos; reconnaissance survey of the area would be of scientific interest. Mayaguez is on the west coast of Porto Rico, at Mayaguez Bay, which is the third in importance of the harbors of the island. The city itself is about ¾ mile inland on the low-lying plain at the mouth of the

Jan 3, 1918

A knowledge of the principles of punctuation is essential to effective and intelligible writing, for the ease and pleasure of the reader, and even his understanding, may depend upon the choice and the placing of punctuation marks. To &apos;punctuate&apos; is to mark with stops or points; the word comes from the medieval Latin punctuare (punctuatus), which in turn is derived from the Latin punctum, a point. The purpose of punctuation is to show the manner in which the writing is to be understood; to indicate the relations between parts of a sentence and between successive sentences. To some extent "it does for the eye what vocal stress does for the ear", but especially it marks logical relations. Some punctuation marks, such as those indicating admiration, exclamation, and interrogation, are rhetorical as well as grammatical, but most of the common ones are logical or grammatical. My discussion will be confined to grammatical punctuation in ordinary writing. "The problem of punctuation in text matter", as George Summey * says, "is to employ words, points, and paragraph breaks in such a way as to achieve at the same time clearness, proper distribution of emphasis, and the desired kind of movement." The criticism of the punctuation of a sentence or of a group of sentences is not final until the context, within the paragraph, is read. A paragraph is a sentence or a group of&apos; sentences forming an independent unit of the composition; it represents a unit of thought. A multiplicity of paragraphs produces a choppy effect; on the other hand, paragraphs of excessive length are tiresome, because the belaboring of one unit of thought wearies the reader. The aim should be to

Jan 1, 1931

NAME "Utah" is derived from the name of the Indian tribe, variously spelled "Yuta," "Ute," "Youta." "Uta." "Eutaw," and finally "Utah." It means "in the tops of the mountains," or "on the heights." The state emblem is the "Beehive," typical of industry. State nickname is "Beehive State." AREA Utah is the tenth state in area. It contains 84.990 square miles, of which 2.806 miles are water. When admitted as a territory in 1850. Utah included all the area from the east line of California to the summit of the Rocky Mountains between the 37th and 42nd parallels, which embraced practically all of the present state of Nevada, all of western Colorado, part of Idaho and part of Wyoming, in addition to the present area of Utah.

Jan 1, 1925