Search Documents

Apr. 9, AIME, Chicago Section, Chicago Bar Assn., 29 S. La Salle St., Chicago. Apr. 11-12, Geological Society of America, Cordilleran Section, annual meeting, University of Arizona, Tucson. Apr. 15, AIME, Morenci Subsection, Longfellow Inn, Morenci, Ariz. Apr. 15-17, AIME, South West district meeting, Jefferson Hotel, St. Louis, Mo. Apr. 17, AIME, Utah Section, New House Hotel; Salt Lake City. Apr. 21-22, American Zinc Institute, annual meeting, Hotel Statler, St. Louis. , Apr. 21-23, Chemical, Metallurgical, and Mining Society, and Diamond Drilling Research Laboratory, symposium on diamond drilling, Johannesburg, South Africa. Apr. 22, Assn. of Consulting Chemists & Chemical Engineers, Inc., general symposium, Hotel Belmont Plaza, New York. Apr. 25-26, AIME, New England Regional Conference, Kenmore Hotel, Boston. Apr. 26-May 11, Liege International Fair, Liege, Belgium. May 4-8, Electrochemical Society, Inc., Spring meeting, Benjamin Franklin Hotel, Philadelphia.

Jan 1, 1952

By C. G. Dunn, P. K. Koh

The primary recrystallization textures of 11 single crystals cold rolled 70 pct were determined. The effect of crystal orientation on recrystallization behavior was investigated also and found to be large. An exception was found to the relationship that strong components of the recrystolliza-tion texture are rotated from the cold rolled texture by 30° about <110> axes, but generally this relationship was found to hold quite well. Evidence supporting oriented nucleotion was found and discussed in terms of probable active slip systems and <110> edge dislocations. THE present paper is one of a series&apos;.&apos; on recrys-tallization phenomena in cold rolled 31/4 Si-Fe single crystals and is mainly concerned with the textures produced on recrystallizing from stable end orientations. Data for the cold rolled textures of the crystals used have been reported by Koh and Dunn." Their results showed that the sharpness of the cold rolled textures varied throughout the range of stable end orientations and that the tendency to re-crystallize was related to the sharpness of the cold rolled texture, wherein the rate of recrystallization increased and the size of recrystallization grains decreased with decreasing sharpness of the cold rolled texture. In the project under consideration the cold rolled crystals involved a range of initial orientations that, together with those studied earlier,&apos; provide information on several points. The first point is whether the recrystallization texture from a (111) [112] cold rolled texture, a stable end orientation that can be approached from different directions, correlates in any way with the initial orientation before cold rolling, or whether the recrystallization texture is entirely determined by the observable features of the cold rolled texture. The second point involves a preliminary study to see if the main components of the recrystallization textures correlate with the most probable active slip systems. The third point is to determine what effect departure from slip on one slip system has on the tendency to recrystallize. Experimental Procedure Nine specimens from a previous investigation and two additional ones from thicker stock (lot D) but of similar composition to the others were used in the present work. The latter two crystals, like the nine, were cold rolled to a reduction in thickness of 70 pct and the amount of widening was determined. Depending on their primary recrystallization behavior, the cold rolled crystals were given short or long anneals at temperatures of 980°C or higher. Table I summarizes the data on initial orientations, the textures obtained by cold rolling, and the anneals given to provide samples for the present work. Fine grained specimens were thinned to 0.002 in. thickness and placed in an integrating specimen holder. Chart recordings using a transmission X-ray method and MoKa radiation were obtained for diffraction from (110) planes. This method,&apos;,3 which gives data for all of the pole figure except a central region of 30" radius, proved sufficient to give generally five, and sometimes six, of the six possible pole concentration areas of any one component of the texture. These data, therefore, were generally adequate for a positive identification of each component present. The first texture obtained for specimen B-2 was poorly defined because of too coarse a grain structure and therefore too few crystals in each component for satisfactory X-ray reflections. The same

Jan 1, 1957

By Edward I. Salkovitz

THE determination of the orientation of metal single crystals and the studies of plastic deformation are greatly facilitated by the use of the stereographic projection. To draw a standard projection of the crystal it is necessary to have a tabulation of the angles between the various crystal-lographic planes of the particular crystal studied. Bozorth&apos; has published such a table for the cubic system which can be found in many reference books; such convenient tabulation for the hexagonal metals, however, does not appear to be in the literature, although scores of workers have calculated these angles. Therefore, Table I of angles for magnesium, zinc, and cadmium has been compiled. Since the c/a ratio is different for each of these metals, three separate calculations are necessary. The angles 4 between (HKIL) and (hkil) were calculated by means of the formula: Hh+Kk+½(Hk + hK)1+~3aLl cos The c/a ratios were calculated from data given in the 1948 edition of Metals Handbook. Fig. 1 is a typical (0001) standard projection of zinc. For all practical purposes, it serves for cadmium as well, as can be seen from the table. For magnesium, however, it is necessary to construct another net. R. M. Bozorth: Physical Review. (1925) 26, 390.

Jan 1, 1952

By Jack G. Gill, Richard A. Dick

Blasting safety is a subject that cannot be overemphasized. Two years ago, a study was published describing g a series of fatal blasting accidents which took the lives of ten metal and nonmetal miners during the period of May 1973 to August 1974.1 Each accident was described, and the direct causes were delineated. In each instance, specific MESA safety regulations were violated. Four of the victims were killed by drilling into explosives; two were killed by lingering too long in the vicinity of fuse rounds; two fatalities resulted from improper guarding of shots; one blaster did not retreat far enough to avoid the blast concussion; and another used an improper tester for checking an electric blasting cap. All of these fatalities could have been avoided by adhering to the MESA blasting regulations contained in 30 CFR Part 55 (Health and Safety Standards-Metal and Nonmetallic Open-Pit Mines), Part 56 (Health and Safety Standards-Sand, Gravel and Crushed Stone Operations), and Part 57 (Health and Safety Standards-Metal and Nonmetallic Underground Mines).

Jan 11, 1977

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By S. P. Holt

The chief use of scrapers at this mine has been on lead ore of milling grade, clean and dry, in stulled stopes, 50-100 ft. long, 5-12 ft. high, and pitching 20-30°. Scrapers have also been used to fill these stopes with waste. The first scraper used (Fig. 1) is modified from a Cleveland-Cliffs design, being only 30 in. wide. It is light, weighing but 95 lb., handles well, and-digs itself in; but it spills part of its load on a long haul. It could be improved by lengthening the side plates, but because of the double bent angle irons, it is difficult to make at mine shops and has been discarded. Fig. 2 shows where the light angle irons have failed, spoiling

Jan 1, 1923

By Charles W. Merrill

Obsolescence in the mineral world is virtually nonexistent if the term is taken to mean that a mineral commodity, once established in commerce and industry, subsequently has fallen into disuse. We are living in an age of minerals. Each generation puts an increasing array of mineral-based commodities, in larger quantities, to more uses than ever before. Bastnasite, a museum mineral and a collector&apos;s item a few years ago, is now produced in quantity at Mountain Pass, Calif. Uranium, a minor byproduct of vanadium mining in the Rocky Mountain plateau area before World War 11, has grown to be a leading mineral product in several western States. And finally the total quantity and value of minerals both in the United States and in the World establish new records almost yearly. Surely the mineral industry as a whole is not obsolescent in our economy. Nevertheless, there are particular uses for particular minerals that are obsolescent and some applications have been supplanted entirely. Tin does not occupy the prominent place in foil manufacture that it once did, and the schoolboy&apos;s slate left most classrooms before the oldest of us were born.

Jan 9, 1964

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, &apos;the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By E. A. Swedenborg

The unit agreement for the Wertz Dome field, Wyoming, was approved by the Acting Secretary of the United States Department of the Interior on November 4, 1937, effective on December 1, 1937. The stated objectives of the agreement are to conserve and put to beneficial use all oil and gas produced; to make possible a uniform withdrawal of oil and gas in order to maintain equalized reservoir pressures; to provide for an orderly determination of the structural features of the productive horizons; and to permit the injection of gas for pressure maintenance. The purpose of this paper is to show by a discussion of the problems involved and the engineering practices employed by the unit operator, how well the objectives of the unit agreement have been accomplished in the development and production of oil and gas from the field. HISTORY AND DEVELOPMENT The Wertz Dome oil and gas field is located 88 miles southwest of Casper and 38 miles north and westerly from Rawlins, Wyoming. It is served by a state secondary oiled road connecting with U. S. Highway No. 220 at Lamont, a distance of 3 miles from the field. It has been a producing field for 27 years, first as an important producer of gas and more recently of oil. The Producers and Refiners Corp. completed Well No. 1, NE1/4SW1/4 sec. 7, T. 26 N., R. 89 W., the first productive well in the field, in September. 1921, in the Muddy sandstone of Upper Cretaceous age, at a depth of 3435 feet for an initial production of 42,000,000 cu. ft. of gas per day. In 1922 pipe lines were laid to Casper, Wyoming, for supplying fuel to the Standard of Indiana refinery, &apos;the adjoining town of Mills. and the Producers and Refiners Corp. pump station No. 6 in Mills; and to Parco (now Sinclair), Wyoming, for supplying that refinery with fuel. The gasoline content of the gas was extracted in an absorption plant located near the town of Mills. No compressors were used as the line pressure was sufficiently high to flow the gas through the absorbers. As high as 30,000,000 cu. ft. of gas per day were treated in the plant extracting 6000 gallons of gasoline. In September 1937, the pipe line was discontinued and the plant was dismantled at which time 61,000,000,000 cu. ft. of gas had been produced from the seven Muddy, Cloverly, and Sundance gas wells drilled in the field. Of this volume of gas 800,000,000 cu. ft. were produced from the Frontier formation, 34,200,000,000 cu. ft. from the Muddy sandstone, 24,000,000,000 cu. ft. from the Cloverly, locally called Dakota, and 2,000,000,000 cu. ft. from the Sundance formation. The pipe line was discontinued because of the near depletion of the gas reserves in Wertz and nearby fields, and hecause of the local field requirements demanding the retention of the remaining gas reserves. In December 1936, the Sinclair Wyoming Oil Co. completed Well No. 10, SE1/4NW1/4 sec. 7. T. 26 N., R. 89 W., at a depth of 5886 feet. as the first Tensleep sand producer with an intial of 1700 barrels of oil per day. The well was originally drilled only 14 feet into the sand and in August 1939 was deepened to a depth of 6161 feet, 289 feet in the sand, and the daily produe tion increased to 8350 barrels of oil. In February 1948 Well No. 22, SE1/4 SE1/4 sec. 1. T. 26 N., R. 90 W., was deepened from the Tensleep to the Basal Amsden sand and completed at a depth of 6635 feet for an intial of 600 barrels of oil per day in the Basal Amsden. In April 1948, Well No. 2. SW1/4 NE1/4 sec. 1, T. 26 N., R. 90 W.. was deepened from the Tensleep to the Madison limestone and was completed at a depth of 7193 feet for an intial of 1145 barrels of oil per day in the Madison. Well No. 26, SE1/4SE1/4 sec. 1, T. 26 N.. R. 90 W., was deepened from the Ten-sleep to the Cambrian and in October 1948 it was completed in the Cambrian for an intial of 277 barrels of oil per day. GEOLOGY AND PRODUCTIVE ACREAGE The surface is Steele shale of Upper Cretaceous age, covered in part by gravel beds. The topography of the field is that of a rolling hill with a steep draw or gulch along the northern edge of the field. The Steele shale lies conformably on the lower formations as

Jan 1, 1949

By E. J. Dulis, A. Kasak, R. C. Westgren

The potential of uirought tungsten- and tantaluw-rich alloys of the W-Ta-Mo-Cb system was investigated for high-strength structural applications above 2500° F. Appreciable strengthening of tung-sten and tantalum—essentially attributable to solid-solzction effects—was obtained with binary, ternary, and quaternary alloys. Tensile strengths as high as 67,000 psi were achieved at 3000 OF. ThE quest for wrought structural materials which possess good strength properties at temperatures above 2000°F has led to a considerable research effort during the past decade. In addition to exploring the potential of various high-melting-point refractory metals (such as molybdenum, columbium, tantalum, and tungsten) for very high-temperature structural applications, alloy-development programs have been undertaken to achieve greater strengths than could be achieved with unalloyed refractory metals. The methods of strengthening refractory metal alloys have included both solid-solution and dispersion strengthening. General relationships among the relevant properties (melting point, recrystallization temperature, and high-temperature strength) of refractory metals indicate that the highest strengths at temperatures of 2500°F or higher would be obtained with tungsten-or tantalum-base alloys. Therefore, the present investigation was undertaken to determine the high-temperature strength potential of solid-solution strengthened alloys based on the binary system W-Ta; to effect further strengthening, minor additions of molybdenum and columbium (at the 6 and 12 pct levels) were made. The portion of the W-Ta-Mo-Cb quaternary alloy system of interest is shown schematically in Fig. 1. The component metals—W, Ta, Mo, and Cb—have a bcc structure at all temperatures, and their binary systems are mutually completely soluble.&apos; Complete solid solubility in the W-Ta-Mo and W-Ta-Cb alloy systems has been demonstrated,&apos; and, therefore, it was expected that the quarternary alloys of the system would also exhibit complete solid solubility at all temperatures. In the virtual absence of contamination by interstitial elements, all the alloys would be truly solid-solution strengthened. Twenty specific compositions of this investigation included binary, ternary, and quaternary alloys of the W-Ta-Mo-Cb system as well as unalloyed tungsten and tantalum. The compositions are shown in Table I. EXPERIMENTAL PROCEDURE Consumable-electrode vacuum-arc melting with ac power was used to produce small laboratory-sized, cylindrically shaped ingots (1-1/4 in. in diameter and 2 to 3-1/2 in. long) of the twenty compositions. A furnace was specially constructed to melt as many as four electrode rods simultaneously into molds lined with tungsten or tantalum sheet. High-purity rods of tungsten, tantalum, molybdenum, and columbium were used for consumable electrodes; the diameter of each rod was determined by the desired weight percentage of the component metal in a given alloy. The details of the construction and operation of the melting furnace will be discussed in another p~blication.

Jan 1, 1964

By S. T. Wlodek

The surface and subscale oxidation reactions were followed by means of continuous weight-gain and metallographic techniques over the range 1600" to 2200°F (871° to 1204 °C) for up to 400 hr. Full identification of all scale and subscale reaction products was obtained by electron and X-ray diffraction. At or below 1800°F (982°C) a linear rate of reaction (QL = 46.0 kcal per mole) governed the oxidation process, extending for up to 100 hr at 1600°F (871 "C). During linear oxidation the surface scale consisted of an amorphous SiO2 film overgrown with Cr 2O 3 and NiCr204. This initial linear process was followed, and above 1800°F completely replaced, by two successive parabolic rate laws (Qp = 60 and 57 kcal per mole). This parabolic reaction involved the formation of a complex scale consisting of Cr2 O3 and smaller amounts of NiCr2O4. Parabolic oxidation appeared to coincide with the disruplion of the silica film present during linear oxidation and was followed by subscale (internal) oxidation of crystobalite and NiCr2O4. The balance between the subscale and surface oxidation reactions controls the oxidation of this commercial alloy. The amorphous silica film appears to result in the linear rate and diffusion through Cr2O3 is the more likely rate-limiting step during parabolic oxidation. THE oxidation of a multicomponent composition is a complex phenomenon not presently amenable to a rigorous classical interpretation. Nevertheless, even a qualitative understanding of the scaling and subscale reactions that occur in a commercial composition can illuminate the reactions that limit its high-temperature stability in an oxidizing environment. This study of the oxidation of Hastelloy Alloy X presents the first of a series of studies with the above approach in mind. Hastelloy X exhibits one of the best combinations of strength and oxidation resistance available in a wrought, solution-strengthened, nickel-base alloy. Although during long time exposure some precipitation of M6C and M23C8 carbides as well as a complex Laves phase occurs, the amounts are probably small enough to have no appreciable effect on the chemistry of the matrix. Radavich has identified the oxidation products on Hastelloy X oxidized for 5 min to 10 hr at 1115°F as NiO and the NiCr2O4 spinel. Oxidation for 5 to 15 min at 1500°F produced a scale of spinel, NiO, and a rhombohedra1 phase, probably Cr2Os. Sannier et 2. have reported continuous weight-gain data for Hastelloy X at 1650" and 2010°F and internal-oxidation measurements after 150 hr at 2010°F. In addition, much of the data on binary Ni-Cr alloys recently reviewed by Kubaschewski and okins&apos; and Ignatov and Shamgunova4 as well as studies of binary Ni-Mo alloys5 are also pertinent to the oxidation of this composition. EXPERIMENTAL Continuous weight-gain measurements and metallographic measurements of subscale reactions were the main experimental techniques used in this study. X-ray and electron diffraction backed up by a limited amount of electron-microprobe analysis served to characterize the nature of the scale- and subscale-reaction products. Two heats of commercial sheet of the composition given in Table I and identified as A and B were used in the bulk of this study. Internal-oxidation measurements were made on a third heat of material in the form of a 0.5-in.-diam bar. In order to assure homogeneity, all heats were reannealed 4 hr at 2175°F prior to sample preparation. weight-Gain Measurement. All specimens (1.5 by 0.4 by 0.03 in.) were abraded through 600 paper, electropolished, and lightly etched in an alcohol-10 pct HCl solution. An electrolyte of 150 cu cm H,O, 500 cu cm HsPO4 (85 pct conc), and 3 g CrO3 at a current density of 0.9 amp per sq cm or a solution of 10 pct HaW4 in alcohol used at 4 v and 0.3 amp per sq cm was used for electropolishing. The resultant surface exhibited a finish of 3 ± 1 p rms. Continuous weight-gain tests were made at 1600°, 1700°, 1800°, 1900°, 2000", and 2200°F on auer&apos; type balances capable of recording a total weight change of 110 mg with an accuracy of k0.1 mg. All tests were made in air dried to a dew point of -70°F and metered into the 2-in.-diam reaction

Jan 1, 1964

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,&apos; two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,&apos; although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.&apos; A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By B. W. Prof. Frazier

I PROPOSE in this paper to treat of the chimney merely as a heat engine, as one of the devices resorted to in practice for the conversion of heat into mechanical work. For the sake of simplicity and clearness in the discussion, let us consider the subject in its simplest form. Conceive a chamber, heated from without, in free communicatioH at one end with the external atmosphere, and at the other end opening into a vertical chimney. Let the. cross-section of the chamber be so great, relatively to that of the chimney, that we can neglect the actual energy of the air passing through the chamber. We will neglect, also, all passive resistances to the passage of the air. We will assume that the cross-section of the chimney is constant, and that the air in passing through it neither gains nor loses heat. The following symbols will be employed in the discussion : Po = the normal pressure of the atmosphere, which, it is assumed, is the pressure existing at the level of the chamber. Po = 10332.96 kilograms per square meter. P2 = the pressure of the external atmosphere at the top of the chimney. To = the, absolute temperature of melting ice by the centigrade scale. This is assumed to be the temperature of the external air at the level of the chamber. To = 273°. T2 =the absolute temperature of the air as it passes from the chamber to the chimney. T3 =the absolute temperature of the air as it issues from the chimney. to, t2, t3 are the temperatures, as recorded on the centigrade ther¬mometer, corresponding to the absolute temperatures To, T2, T3 re-spectively to = 0° C. In general, t = T- 273. Io, I2, I3, represent the intrinsic energy of the air at the temperatures To, T2, T3 respectively.

Jan 1, 1882

The income of the Institute is derived from dues, subscriptions to MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1936

By Frank B. McKune

This is something new in my life. A lot of you men here today I do not know, and some I do know. So if you have any remarks to make, I wish you would give your name and the name of your company. This is the first Acid Meeting which has been held under the auspices of the National Open-Hearth Steel Conference, and I hope it is a success. Whether it is a success or not depends entirely upon the support we get. If it does get good support, I have the idea it will be continued as a regular feature of the National Open-Hearth Steel Conference. We all think we have pretty good practices. But we can all learn and I hope that you, gentlemen, who take issue with the things someone else has said will stand up and give your opinions. Otherwise, the meeting will fall rather flat, and we won&apos;t get a great deal out of it; and there will not be enough interest shown by the National Committee to continue to place the meeting on the regular yearly program.

Jan 1, 1940

By L. E. Fish, G. S. Wyman

CHUQUICAMATA open-pit mine is capable of producing a total of 105,000 tons daily. When the sulphide plant is operating to capacity the distribution of this quantity will be approximately 30,000 tons sulphide ore, 30,000 tons oxide ore and 45,000 tons of waste. At that time the combined capacity of the oxide and sulphide plants will be about 540 million lb of copper per year. Twenty one benches have been opened to date and all are still active except the three top ones at the northeastern limit of the pit. These have been pushed back to final slope line. The pit is 8850 ft long, 3540 ft wide and 980 ft deep. Benches are not all developed to a standard height as the large development shovels used in cutting new benches have been of different size and range. At this time new benches 521 ft high are being developed with an&apos; 11-yd shovel. Ore haulage through the greater part of the pit operation has been on down grades to the crushing plant. With the opening of bench F-4 in April 1944 the first adverse-grade ore haul was encountered. Of the total tonnage now being mined, 35 pct comes from the four benches that are below the level of the crushing plant yard. Waste had been dumped on the same or nearly the same level as the bench from which it was removed up to the opening of bench F-4. Waste from this and lower levels is hauled to the level of the crusher, yard where it must cross the flow of ore traffic to reach the only available dumping space to the east of the mine. The average ore haul is 3.13 miles one way shovel to crusher, and the average waste haul from that portion handled by railroad is 3.32 miles one way from shovel to waste dump. Waste that is being removed by truck haulage from the upper part of the -mine is hauled an average of 1 mile. Ore loaded by trucks is hauled 3/4 mile to a car loading ramp and then by rail to the crushing plant. Drilling and Blasting There are two types of development for blasting being used: One for opening new benches and the other for bank shooting. The former consists of 9a in. diam churn-drill holes drilled 11.8 ft center to center in rows 10.2 ft apart with the holes staggered in the rows thus giving an equilateral-triangle pattern of 11.8 ft on a side. After the first block, 492 ft long by 71.5 ft wide, is shot in the pattern described above, the cut is advanced by smaller shots consisting of four rows of holes spaced 23 ft center to center with the rows 23 ft apart. These shots are fired in conjunction with side shots in which the holes are drilled 33 ft center to center and 29.5 ft back from the toe, thus squaring up the bank for subsequent shooting. An average bank shot consists of about 60 holes drilled in two rows parallel to the face, 30 holes to

Jan 1, 1952

By J. C. Martin

Equations for three-phase, three-dimensional, compressible flow (including capillarity) are reduced to two-dimensional relations by a partial integration. This reduction allows three-dimensional flow problems to be treated with mathematics for only two spatial dimensions. The results can be used to formulate flow equations for two-dimensional reservoir simulators in which the effects of capillarity and fluid segregation in the third dimension are represented. Such reservoir simulators would retain many of the aduantages of two-dimensional simulators while simulating three-dimensional effects. The principal restriction of the method is that the thickness of the reservoir should be small, compared to the distance across the reservoir. INTRODUCTION In recent years, computers have been used to calculate the performances of many reservoirs. Most of the detailed calculations, however, are based on finite difference solutions of the flow equations, and present day computers are seldom able to handle a sufficient number of cells to produce entirely satisfactory solutions, even for reservoirs represented by two-dimensional arrays of cells. The situation becomes much worse when one wishes to approximate the reservoir by a three-dimensional array. A great saving in computation or a more detailed solution can be obtained for many reservoirs by using the partial integration of the equations of flow presented in this paper. The integration reduces the three-dimensional equations to two-dimensional relations; and, for studies of two-dimensional flows in vertical cross-sections, the equations are reduced to one-dimensional relations. Most reservoir performance calculations currently are based on one- or two-dimensional flow re1ations.l-3 In some cases flow in the third dimension is approximated by assuming a particular type of vertical saturation distribution, such as gravity segregation.l.2. The relations developed in this paper approach those for segregated flow as the capillary pressures approach zero, and they approach those for uniformly distributed saturations as the capillary pressures are increased. For this analysis, the ratio of the reservoir&apos;s thickness to the maximum distance across it must be small. The capillary pressures between the oil and water should also be small compared to the maximum pressure difference in the reservoir. This requirement is met by most reservoirs. It is assumed that the capillary-pressure curves are well defined, whether or not hysteresis effects are included. Also, the reservoir must have sufficient vertical permeability to allow the fluids to segregate. The results presented here provide a firm theoretical foundation to Coats&apos; et aL5 assumption of vertical equilibrium and extend the relations to three-phase flow. Coats&apos; assumption of vertical equilibrium, which he verified by calculations and experiment, is developed here mathematically from basic flow equations. DISCUSSION SATURATION AND PRESSURE DISTRIBUTIONS Appendix A presents a mathematical analysis of fluid flow in reservoirs where the ratio of thickness to maximum distance across the reservoir is small. The results indicate: (1) that the fluids along any line perpendicular to such a reservoir&apos;s upper surface are in static capillary equilibrium (vertical equilibrium); (2) that, to a first approximation, the fluid pressures and properties are functions of only areal position in the reservoir and time; and (3) that hydrostatic pressure gradients exist along any line perpendicular to the reservoir&apos;s upper surface. The results might be expected after studying several physical considerations. First, no flow is allowed normal to the upper and lower reservoir boundaries, which are relatively close together.

Jan 1, 1969

By Rogers Wade

THE Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) South of the international boundary and about 7 mi. (11.26 kin.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The

Jan 8, 1919

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years&apos; experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8&apos;9&apos;11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth&apos;s magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

By M. Smutz, C. J. Baroch, E. H. Olson

IN 1949 an orebody containing some 10 billion lb of recoverable rare earth metals was discovered in the Mountain Pass district of San Bernardino County, California.&apos; The following year Molybdenum Corp. of America purchased a number of claims at the deposit and a mill on the property which had been constructed to process the district&apos;s gold ores. Average composition of ore from the San Bernardino deposit is less than 0.1 pct Tho2, 25 to 35 pct calcite, 10 pct rare earth oxides, 15 to 20 pct silica, and 30 to 40 pct barite.&apos; Rare earth content of the ore analyzes 50.7 pct CeO2, 4.2 pct Pr6O11, 11.7 pct Nd2O3;, 1.3 pct Sm2O3,, and 34.3 pct La2O3 and others.&apos; By floating the barite and depressing the bastna-site, Molybdenum Corp. of America produced a concentrate that contained 60 to 70 pct rare earth oxides. More than 25 pct of the rare earths, however, was lost in flotation. It seemed likely that a more economical method could be found. At the present time most of the rare earths in the concentrates are converted to rare earth chlorides, which are either fed to ion exchange columns for separation of the individual rare earths or reduced to misch metal. Current investigation shows that solvent extraction may achieve this separation more economically than ion exchange. The study reported here was undertaken to develop an economical method of preparing a pure rare earth nitrate mixture from California bastnasite ore. Results indicated that more than 98 pct of the rare earths could be recovered. Several possibilities were considered for processing bastnasite ore, but only the method outlined in Fig. 1 was investigated. This involved leaching the calcined ore with nitric acid. The nitric acid process is discussed under the following headings: 1) calcination of the ore, 2) leaching of calcine, 3) filtration studies, 4) solvent extraction, and 5) nitric acid recovery. Calcination: Since California bastnasite ore contains 25 to 35 pct calcite and about 10 pct bastnasite, calcination was needed to reduce the violence of reaction with nitric acid. Weight losses of 26 to 30 pct were obtained by calcining the ore at 900°C for I hr or at 800°C for 4 hr. Longer periods resulted in no further weight loss. Leaching the Calcine: When the bastnasite calcine was leached with 30 pct nitric acid for 8 to 10 days, rare earth recoveries of only 45 to 50 pct were

Jan 1, 1960