Search Documents

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By M. Muskat

A theory has been developed describing the behavior of wells and reservoirs producing by the action of bottom water drives. It is assumed that the pressures are maintained above the bubble point, and that the permeability to viscosity ratio of the water in the flooded zone is the same as for the oil in the oil-saturated pay. Accordingly, the treatment is based on the homogeneous fluid potential theory. The effect of the difference in density between the oil and water is neglected. .4fter deriving the proper potential distrihutions, the nature of the rise of the water-oil interface below the producing wells is calculated. The primary clean-oil-production phase is expressed in terms of the displacement efficiency, defined as the fraction of the pay flooded out by the rising water table at tlle time of first water entry. The variation of this displacement efficiency is calculated as a function of the well spacing, pay thickness, the ratio of the horizontal to vertical permeability, and the well penetration. The important parameter, other than the well penetration, is found to be the ratio of the well separation to the thickness of the oil pay multiplied by the square root of the ratio of vertical to horizontal permeability. It was found that the displacement efficiency continually decreases as this parameter increases, and for values of the latter >3.5, the efficiency varies inversely as the square of the parameter. It also increases with decreasing well penetration. Perhaps the most striking result of this phase of the analysis is the conclusion that in order to explain the delay in entry of water in wells producing by bottom water drives for periods longer than a few days normal production, with drawdowns large compared with the differential density head between the oil and water, it is necessary to assume that the vertical permeability is a very low fraction of the horizontal permeability. An analysis is also given of the production history after the water has broken through, on the assumption that the production mechanism and details of the flow distribution continue to be the same as during the phase of clean-oil production. As is to be expected, it is found that the water cut will increase at an accelerated rate as production proceeds. However, the initial differences between systems of different well penetrations or well spacings with respect to the total clean-oil production gradually decrease in terms of the variation of the water-oil ratio with cumulative production. In particular, by the time the water-oil ratio has reached values of the order of 5 or greater the cumulative recoveries will generally differ much less among various producing systems than their corresponding clean-oil recoveries. Introduction On the basis of elementary geological principles, one may classify effective water-drive fields in two groups. In the first, the entry of water into the oil-producing formation may be characterized as an edge-water encroachment. This term is used to suggest that the motion of the water proceeds largely in a direction parallel to the planes of stratification. This type of water intrusion occurs usually in thin producing zones and in strata lying along structural flanks of appreciable dip. In the second group—"bottom water-drive" fields—the water-oil interface lies in a plane of zero or slight inclination to the

Jan 1, 1947

By R. S. Archer

SILICON is one of the most important elements in the metallurgy of aluminum. It is always present in small amounts in the ordinary grades of "pure" aluminum, and hence in all alloys made therefrom. Within the last few years binary alloys containing up to 13. per cent, of silicon have come into extensive use for castings. Silicon is also added, beyond the amount present as an impurity, in alloys containing one or more other elements such as copper, manganese, magnesium and nickel. The binary aluminum-silicon alloys are not yet heat treated to any extent in commercial practice, although, as will be shown, their properties are affected to a very considerable degree by heat treatment. There are other aluminum alloys that develop higher strength, but the special characteristics of the silicon alloys may well lead to the application of heat-treating processes on a commercial scale. The role of silicon in the heat treatment of aluminum alloys is more important than would be indicated by consideration of the binary alloys alone, because many of the alloys that are heat treated in regular commercial practice contain some silicon in addition to that derived from the aluminum ingot as an impurity. Among these may be mentioned the heat-treated 195 alloy castings, and the wrought alloys 258, Special 178 and 51S of the Aluminum Co. of America, and the German wrought alloy, Lautal. It is the purpose of this paper to present the results of experimental work and the conclusions derived therefrom regarding the heat treatment of the binary aluminum-silicon alloys. The products heat treated included forgings, chill castings and both "normal" and "modified" sand castings.

Jan 1, 1927

DISCUSSION, M. Cohen presiding A. H. Geisler and D. L. Martin (GeneTal Electric Research Laboratory, Schenectady, N. Y.)—We were rather interested to note the author's conclusion that the cubic to tetragonal transformation may be of the second order, for we have been able to show that the order-disorder transformation in an analogous alloy system is a first-order transformation with a discon-

Jan 1, 1952

By H. A. J. Wilkens, H. B. C. Nitze

From time to time papers treating of specific cases of Southern gold-mines and mining have appeared in the Transactions of this Institute, as well as in other journals and publications. Mr. George I?. Becker, of the United States Geological Survey, made a reconnaissance of the Southern Appalachian gold-belt during the fall of 1894; the results of his investigations are published under the title of "A Reconnoissance of the GoldFields of the Southern Appalachians," in the Sixteenth Annual Report of the Director of the United States Geological Survey, 1894-95 : Part III., " Mineral Resources of the United States." Mr. Becker has treated the subject mainly in a scientific geological manner. We present this paper to the members of the Institute as requested by the Secretary last May, with the object of covering the ground from a more practical and technical standpoint. The notes for this paper were made in a large measure from personal observations, gained chiefly during the past summer on a trip through the field. In connection with this trip we collected a suite of typical hand-specimens, representing the gold-ores and wall-rock from the more important localities. This collection forms a part of the exhibit

Jan 1, 1896

By E. R. Parker, R. H. Thielemann

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By R. H. Thielemann, E. R. Parker

The conventional short-time tensile test provides a reliable means of predicting the sustained load-carrying capacity of steels only when the temperature is such that continuous plastic flow does not occur. At elevated temperatures, stresses considerably less than the short-time rupture value may produce continuous flow, with fracture occurring only after long periods of time. The amount of flow or creep accompanying failure varies for different steels, and depends, to a large extent, on the temperature and the duration of the test. Service records of cracking stills, steam superheaters and high-temperature boilers have shown that brittle fractures sometimes occur with little or no warning. In installations of this type, localized stresses are often encountered, and steels must be capable of withstanding a certain amount of deformation without fracture. The sustained-load rupture test determines the expected life and corresponding ductility of steels at various stresses and temperatures. It also yields additional information regarding the effect of micro-structure and metallurgical stability on the high-temperature properties. Present Status of Sustained-load Rupture Test The sustained-load rupture test conducted at elevated temperatures is not entirely new. Dr. Zay Jeffriesl presented in 1919 the results of a large number of rupture tests made on copper, iron and tungsten. These tests were made with various strain rates and at temperatures ranging from the boiling point of liquid air to 1000° C. At that time he observed the interesting phenomenon characteristic of metals, that a temperature exists below which a metal is ductile and breaks with a transcrystalline fracture (through the grain) and above which the metal is brittle and breaks with an intergranular fracture (through the grain boundaries). He observed that this temperature varied with the testing speed, and that a minimum temperature, slightly above the recrystallization temperature, existed at which the cohesion of the grains themselves was

Jan 1, 1939

By J. M. Ross

THE Homestake mine is situated in Whitewood mining district, in the northern Black Hills of South Dakota, in the city of Lead, Lawrence County. The entire property, comprising 557 lode claims with a total area of 3343 acres, is held under United States Patent. The older claims were 300 by 1500 ft. under local regulations, the newer ones 600 by 1500 ft. The Homestake was discovered April 9, 1876, by Moses and Fred Manuel, and Jake Harney, who were drawn into the northern hills, from the Custer placer district, by news of the discovery of rich placer deposits in Deadwood Gulch. They located a number of additional lode claims and, in a short time, the whole country was covered with locations. The Manuel brothers built an arrastre the following winter and took out $5000. The next year the Homestake lode was sold to Senator George Hearst and associates, who organized the Homestake Mining Co. Other companies were formed to exploit other groups of claims and at one time five companies were operating on this deposit, the Father DeSmet, the Deadwood-Terra, the Caledonia, the Highland, and. the Homestake Mining Co. These companies, however, have been merged into the Homestake Mining Company. The first stamp mill, known as the "Eighty Mill," commenced operation on July, 12, 1878, and production has been nearly continuous since that time.

Jan 2, 1925

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By A. B. Calhoun

These mines, which belong to the Burma Corporation, Ltd., formerly a London company now incorporated in Rangoon, Burma, are situated in the semi-independent state of Tawng-Peng, one of the small divisions comprising the northern Shan states and erroneously known as part of Upper Burma. Bawdwin is approximately 23' 6' N. latitude and 97" 20' E. longitude, 450 miles north of Rangoon, 169 miles northcast of Mandalay and 50 miles south and west of the Province of Yunnan, China (see Fig. 1). Although the mines were worked by the Chinese during the Ming Dynasty, 1412 A. D., the most extensive operations took place between 1796 and 1851, when the mines contributed largely to the silver market of China. During the reign of Tung Chik, 1868 A. D., they were abandoned partly because of the Mohammedan rebellion in Yunnan, which made life and property insecure, but largely because of the difficulty of operating the mines on account of water and poor ventilation. Since that time practically nothing was done, although the Burmese kings are said to have made several sporadic attempts to work the mines, until 1891 when Europeans were attracted by the great slag dumps (assaying about 40 per cent. lead) which the Chinese had left after extracting the silver. After a railroad and smelter had been built and 200,000 to 300,000 tons of slag smelted for lead, exploration work was started and old workings cleaned out in order to locate the remnants of the orebody that it was supposed the Chinese had left. After two years of most discouraging work, the remains of a large orebody was discovered by the Dead Chinaman Tunnel or what is the 171-ft., or No. 2 level adit. From then on the development was rapid and today the Chinaman is considered one of

Jan 1, 1923

By A. B. Calhoun

These mines, which belong to the Burma Corporation, Ltd., formerly a London company now incorporated in Rangoon, Burma, are situated in the semi-independent state of Tawng-Peng, one of the small divisions comprising the northern Shan states and erroneously known as part of Upper Burma. Bawdwin is approximately 23' 6' N. latitude and 97" 20' E. longitude, 450 miles north of Rangoon, 169 miles northcast of Mandalay and 50 miles south and west of the Province of Yunnan, China (see Fig. 1). Although the mines were worked by the Chinese during the Ming Dynasty, 1412 A. D., the most extensive operations took place between 1796 and 1851, when the mines contributed largely to the silver market of China. During the reign of Tung Chik, 1868 A. D., they were abandoned partly because of the Mohammedan rebellion in Yunnan, which made life and property insecure, but largely because of the difficulty of operating the mines on account of water and poor ventilation. Since that time practically nothing was done, although the Burmese kings are said to have made several sporadic attempts to work the mines, until 1891 when Europeans were attracted by the great slag dumps (assaying about 40 per cent. lead) which the Chinese had left after extracting the silver. After a railroad and smelter had been built and 200,000 to 300,000 tons of slag smelted for lead, exploration work was started and old workings cleaned out in order to locate the remnants of the orebody that it was supposed the Chinese had left. After two years of most discouraging work, the remains of a large orebody was discovered by the Dead Chinaman Tunnel or what is the 171-ft., or No. 2 level adit. From then on the development was rapid and today the Chinaman is considered one of

Jan 1, 1923

By George J. Clark

One of the major problems of operation in the anthracite industry is the disposal and handling of refuse—not because of its complexity but because of the quantity and type of material involved. It is the purpose of this paper to describe the kinds of refuse, methods of disposal, quantities of material to be handled and equipment used, together with present day application at specific operations in the Northern, Eastern Middle, Western Middle and Southern anthracite fields. For the purpose of this paper, refuse is considered to be any material that has no present or foreseeable future value and that must be handled and disposed of in the process of mining and preparing anthracite for market. Included in this classification are tunnel rock, mine rock, cleaner plant refuse, breaker refuse, old timber, ashes and silt. Disposal Methods Old timber is disposed of either by burning or by depositing on the refuse bank. Burning is preferred because timber on the refuse bank is a potential fire hazard. Ashes are deposited on a separate bank, mixed with other refuse, or flushed into old mine workings. In many places, the latter practice has caused considerable difficulty in preparation of coal mined from these areas. In depositing ashes on the surface, it is wise to refrain from mixing them with material containing coal as such contamination may prevent reclamation of the coal in future years. Tunnel work, mine rock, cleaner plant and breaker refuse compose the bulk of the material to be disposed of and handled, and are referred to collectively as "refuse" in this paper. Waste material in or adjacent to the coal beds may be removed at the working face wherever possible. This can be done in flat or lightly pitching beds, and in the Northern field represents a sizable percentage of this type of refuse handled. In the other three coal fields, this method of disposal cannot often be used. Refuse not removed at the working face is taken to the surface and generally is deposited on banks; occasionally it is crushed and flushed into old mine workings. Breaker refuse often is used for constructing berms for silt-retention basins. Disposal Problems The problem of handling refuse is different for each operation, owing to topographical conditions, quantity of material to be handled, anticipated requirements and types of equipment in use elsewhere at the operation. Preparation plants with limited refuse-disposal areas, excessive grades to reach the required elevation and long hauls to disposal areas not readily accessible require the selection of equipment to best meet the conditions. The quantity of refuse to be handled from a given amount of raw material varies considerably throughout the four fields. In mine coal, this varies from a low

Jan 1, 1949

By G. L. Oldright, Henry de Rycker, S. F. Ravitz

The upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the operation of sintering. A sinter feed with normal gangue constituents, containing more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead concentrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1944

By G. L. Oldright, F. W. Schroeder

Very great changes were made in the dimensions of the smelting hearths of the furnaces in the period from about 1800 to 1906, the length increasing from about 11 to 116 ft., and the width from 8 to 19 ft. During this time the tonnage smelted increased from about 9 to 250 tons per 24 hr., and the tons of charge smelted per ton of coal increased from 0.77 to 4.3. Dr. Mathewson3 noted no great difference in the "fuel ratio" (i. e., the amount of charge smelted per ton of coal) as the furnace at Anaconda was increased in length by stages from 85 to 116 ft. (The percentage of copper in the slag, however, was lowered from 0.42 to 0.36 per cent. The other components of the slag were not given.) Lump coal fired on grates was the fuel used during this period. The practice in operating the furnaces over such a length of time naturally varied considerably, and there were differences in composition and nature of the charge, yet it may he considered that the improvements made were due largely to increases in the size of the furnace used. Doubtless some credit should be given to improvements in operating technique, like changes in the methods of firing the lump coal. However, the greater part of the advance was probably due to factors influencing the

Jan 1, 1928

By P. B. Knuckey, D. Littleford

The Kalengwa mine, situated in a remote area of Zambia in Central Africa, has presented some unique problems to the planners engaged in developing the deposit. This small, high grade copper deposit contains some 1,688,000 tons of ore at a grade of 9.3% contained copper. Of this 362,000 tons is classified as high grade ore at 27.2% Cu, the coarse fraction of which can be fed directly to converters; 733,000 is classed as intermediate grade ore averaging 6.3% Cu, and 593,000 tons classed as low grade ore containing 2.1% Cu. The geology of the deposit and the establishment of the mining operation is fully described. A concentrator is being built at Kalengwa to treat the high grade fine product, intermediate, and low grade ore, whilst the coarse high grade ore will be trucked to the Copperbelt smelters for direct smelting. Details of metallurgical processing are given. The decision to truck the coarse high grade ore to the smelters on the Copperbelt necessitated the construction of a new 200-mile road, the setting up of a fleet of heavy ore transport trucks and associated equipment. The remoteness of the area from established communication facilities on the Copperbelt necessitated the provision of radio communications between Kalengwa and the head office at Kalulushi, and the establishment of a regular mine air service. The paper also describes the training of an unsophisticated local population in the operation of heavy plant and machinery, the establishment of the township, and the provision of health services.

Jan 1, 1972

By W. C. Ellis

NONFERROUS alloys upon which desirable properties can be conferred by heat treatment are becoming of increasing industrial importance. The alloys of copper with a constituent which has a solubility varying with temperature are materials of this character. Some of the constituents which are effective in producing a change in the mechanical properties of these alloys upon heat treatment are, according to Corson,1 nickel and silicon, iron and silicon, cobalt and silicon, and chromium and silicon. In addition to these elements, Gregg2 states that the combination of beryllium and silicon is effective in producing age-hardening characteristics in copper. The effect of these elements, however, as dispersion-hardening constituents in the copper alpha solid solutions does not seem to have been studied in any considerable detail. This paper deals with the heat treatment and properties of three alpha brasses containing 3 per cent. of nickel plus silicon in the proportion necessary to form the compound nickel silicide, Ni2Si. Some information of a preliminary nature in regard to the hardening by heat treatment of phosphor bronze containing the same percentages of nickel and silicon is included. The method of hardening the alloys, which is effective in increasing the tensile strength and proportional limit, is similar to that used in, the case of duralumin type aluminum alloys. It consists of a quench from a temperature at which the hardening constituent is in solid solution, followed by an aging at a lower temperature to precipitate the dissolved constituent in a dispersed condition. This results in an increased resistance of the alloy to deformation with an attendant improvement in the tensile properties.

Jan 1, 1929

By H. C. Schultz, F. K. Middleton Hunter

Certain local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to develop usefully its full disruptive effect in hard ground. The individual blasts at Chuquicamata arc large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with 1,. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast. Present Liquid-oxygen Plant An experimental unit with a rated capacity of 75 liters per hour was erected during the latter part of the year 1926 to prove the effectiveness of L. 0. X. at this mine, its cost, and possible efficiency of large-scale storage of the liquid. With this experimental unit 200,000 tons of ore

Jan 1, 1928

By G. H. Matheson, J. M. W. Mackenzie

The flotation rate of coal has been studied using a continuous laboratory flotation cell and a multiple exposure photographic technique. The effects of particle size, reagent additions and cell turbulence on the flotation rate of coal have been investigated. The results have been analyzed in terms of current theories of particle bubble encounter and adhesion. The rupture forces which occur during particle bubble encounter have been shown to have an important effect on the flotation rate of coarse coal particles. The flotation of coal is a time dependent process, and in order to obtain a complete understanding of the operation it is necessary to determine the kinetics of the process. In coal flotation, the flotation rate and the associated values of cell productivity in terms of tons per kilowatt-hour and tons per cubic foot of cell volume are of greater importance than in most other mineral flotation operations. The reasons for this are associated with the low unit value of coal and the relatively high cost of coal flotation compared with other coal cleaning processes. An important aspect of coal flotation kinetics is the design of coal flotation cells. The cells used in many coal cleaning operations are often replicas of those used for the treatment of sulfide ores and are not necessarily suitable for the treatment of coal washing pulps, which usually contain a higher percentage of coarse and floatable material than the sulfide pulps for which the cells were designed. This disadvantage of many coal flotation cells has been recognized by Russian engineers who, by the addition of baffles to their subaeration coal flotation cells have increased the cell capacity by 100%. Investigation of the variables which influence flotation kinetics and cell productivity are, therefore, important to the coal industry where flotation is the only accepted method of cleaning the fine (-1/2mm) coal. The kinetics of the flotation process have been investigated in detail by Schumann10 who developed a continuous flotation cell which permitted the study of flotation under steady state conditions. This technique has been used by Gaudin et a1.,6 Brown and Smith and recently by Jowett and Savfi.7 The latter authors have developed a refined mathematical treatment for interpreting the results of continuous laboratory tests. Attempts have also been made to study flotation kinetics using conventional batch testing techniques. The experimental difficulties, however, and the problems of determining the order of the flotation rate process have made this technique of dubious value. A summary of the proposed rate equations for batch testing and the difficulties associated with this technique is given by Brown and Smith. 2 The experimental techniques described above are concerned with the rate of production of froth product. However, several authors, notably Sutherland, 11 Bogdanov1 and Philippoff, 9 have analyzed flotation

Jan 1, 1963

By C. D. Wiseman

THE concept of alloying to increase the strength of metals originated during the bronze age. However, at the present time there is no single theory capable of explaining all of the observed strengthening effects of alloying elements on the mechanical properties. In general, it may be said that solid solutions are stronger than the pure metal and that the strengthening effect increases with increasing alloy content. Various theories for solution hardening have been proposed, the first of which was presented by Rosenhain who suggested that the alloying elements roughened the slip planes, thereby requiring a higher stress to initiate slip. Recent work by French and Hibbard2 confirmed Norbury's3 conclusion that those alloying elements which cause a greater change in lattice parameter have larger effects on hardness. However, a given change in lattice parameter produced by different alloying elements does not cause the same change in hardness. A further refinement was suggested by Dorn, Pietrokowski, and Tietz4 who considered differences in valence between the solute and solvent with the change in lattice parameter to explain the plastic properties of aluminum alloys. Allen, Schofield, and Tate5 further investigated the valency contribution to solution strengthening by testing some copper-base solid-solution alloys having constant electron densities. Tensile tests performed on these alloys gave identical stress-strain curves even though the atomic size effect, which varied by a factor of two, was neglected. The advent of dislocation theory6-8 provided a new and powerful tool capable of explaining many phenomena of plastic deformation and indicated new approaches to solution hardening. The basic con- cept of recent theories is that solution hardening is not due to stresses associated with randomly dispersed solute atoms, but rather to a nonuniform distribution of the solute. This conclusion was reached by consideration of the effective tension present on each dislocation line and the ability of a dislocation to pass an obstacle. cottrell suggested the possibility that the internal stresses due to randomly distributed solute atoms would offer essentially no resistance to the passage of dislocations. He reasoned that an edge dislocation may be considered as a rigid line discontinuity. As the dislocation moved through a crystal, the random stress fields would be equally distributed along its length. Since half of the stress fields would be acting to move the dislocation forward and the other half trying to move it back, the net effect on the dislocation would be zero. Thus the randomly distributed solute atoms would not contribute appreciably to solution strengthening. Mott and Nabarro10 considered the dislocation as a flexible, rather than a rigid, discontinuity. They obtained a simple model for a dislocation moving in a lattice having precipated particles, where the dislocation would actually bend around the obstacle until it would loop back onto itself to rejoin and then continue onward. Their work indicated that the minimum radius of curvature of the dislocation line, under the action of an external stress and in the region of an internal stress, would be such that the dislocation would be unable to pass through a matrix containing small closely spaced precipates by the looping process. The dislocations would tend to remain rather straight, approaching the condition of Cottrell's rigid dislocation. Hence, the strengthening must not be due to random solute atoms; however, it might be due to the concentration of atoms, either as clusters of like atoms or as short-range ordered regions, or to the concentration of solute atoms around dislocations. To date, four mechanisms of solution strength-

Jan 1, 1959

By K. W. Smith, E. A. Thomas

Various grades of synthetic mullite have been developed in recent years to replace or supplement natural sources of mullite deriued from the mullite group of minerals consisting of sillimanite, kyanite, and andalusite. Raw materials and heat treating processes used in making synthetic mullite are described. Chemical and physical data are given for typical grades and crystalline structure is illustrated with micrographs. Use of synthetic mullite as a refractory material in the glass and metallurgical industries is discussed. Mullite (3A12O3.2siO2), the only stable compound formed in the alumina-silica system, is usually present to some degree in all aluminum silicate ceramic products. The formation of mullite is considered beneficial to give rigidity to the structure and is dependent upon the ratio of Al2O3 to SiO2 in the original composition, particle size, degree of mixing, firing temperature, cooling rate, and the presence of auxiliary glass-forming fluxes. Mullite may also be formed at the reaction interface of fire clay or alumina-type refractories in contact with glass or slag melts. The term synthetic mullite is commonly used today to identify a class of sintered and fused aggregates or grains in the alumina-silica system having a highly developed mullite structure but derived mainly from raw materials other than the sillimanite group of minerals. Within the past 15 years extensive research has been done to develop economical processes to form sintered synthetic mullite aggregate to replace calcined Indian kyanite in super-refractories. Severa1 brands of such mullite are now being produced in commerical quantity and finding extensive use in refractories. Based on the service results of such refractories in many applications throughout the metallurgical, ceramic, and glass industry these developments have been considered successful and suitable substitutes for Indian kyanite now appear assured. EARLY DEVELOPMENT The conversion of kyanite, sillimanite and anda-lusite minerals of the sillimanite group to mullite and their use in refractories and porcelain have been discussed quite extensively in the literature by peck,' Grieg,' Riddle and Foster,3 Bowen and Grieg,4 and others and will only be mentioned here for reference to compare properties with synthetic mullite. In 1928, curtis5 reported on the development of a high temperature gas-converter process for forming synthetic mullite. The raw materials were derived mainly from lumps of high alumina clay of the correct natural composition or blends of clays and alumina that was interground and briquetted to form a suitable charge to maintain a surface combustion firing within the converter. Curtis was, no doubt, the first to illustrate by micrographs in natural color the crystalline structure of mullite derived from kyanite and mullite derived by sintering clay and alumina mixtures at temperatures above cone 32 (3123°F) and by electric fusion. In 1937, sei16 was issued a patent covering the use of a mixture of alumina-silica minerals and alumina in the proportion to form a mullite-yielding material at temperatures in excess of 3100' F. During the period from 1930 to 1940, economic conditions were not favorable for the production of synthetic mullite mainly due to an adequate supply of good grades of Indian kyanite ore suitable for conversion to mullite. Uncertain conditions on availability of the Indian kyanite during the early stages of World War II fostered further study on the development of synthetic substitutes. In 1943, McVay and wilson7 reported on an extensive investigation of domestic substitute materials. Their work covered essentially the use of mixtures of electric furnace mullite, calcined topaz, and calcined domestic kyanite. Compositions were found that gave equivalent or better hot load strength than Indian kyanite in mullite-type brick compositions; however, the calcining of the topaz presented certain physical and chemical problems on the disposition of silicofluoride and hydrofluoric acid while the high cost of electric furnace mullite was a limiting factor. In this work it was pointed out that water-quenched fused mullite was found to be unstable on reheat and gave poor hot load strength due to excessive glass present whereas the slow cooled or annealed mullite contained large crystals of mullite and corundum with little glass and gave superior results.

Jan 1, 1961