Search Documents

THE total crude production from the Dutch East Indies, and the British Protectorates of Sarawak and Brunei for 1932 is given in the following table: BARRELS BARRELS (42 GAL.) (42 GAL.) North Sumatra 4,226,935 Ceram 326,207 South Sumatra 13,956,157 Sarawak 2,739,650 Java 3,845,568 Brunei 1,322,725 Dutch Borneo (main island) . 9,406,733 Dutch Borneo (Island of Tara- kan) 6,579,184 Total 42,403,159 Production, which had shown a rapid increase from 1921 to 1929, has since been reduced. Exploitation drilling in the majority of the larger fields was suspended and existing production kept within predetermined limits by beaning. Most of the smaller fields were shut down entirely. The depth of producing levels varies widely in the different fields. Shallow fields with drilling depths to 500 meters (1650 ft.) are still numer-ous as well as those with depths between 500 and 1000 m. (3300 ft.). A few of the newer fields reach greater drilling depths. up to 1600 m. (5250 ft.). The deepest exploration well drilled to date (Djambi field, South Sumatra) reached a depth of 2332 m. (7650 ft.) before abandon-ment in March, 1930. The specific gravities of the various crude oils produced range between 0.65 (86.2° A.P.I.) and 0.95 (17.5° A.P.I.). The lighter crudes have a high gasoline content and fuel oils are derived from the heavier crudes, which usually are rich in paraffin.

Jan 1, 1933

By C. Dirksen

This study investigates whether oxygen consumption during segregated forward combustion may be affected by natural convection. Linear theory indicates that thermal instability occurs in a horizontal porous medium when the modified Rayleigh number N 'Ra exceeds a critical value of about 40. Most experimental results, including those described here, indicate this value to be about an order of magnitude smaller. N ', is derived from "differential similarity" and the proper time scale factor is also obtained. The critical value of N'ra for a horizontal, water-saturated porous medium at atmospheric pressure subjected to a uertical temperature gradient was found to be about 3.0. The ambiguity in the value of N'R, arising when fluid properties cannot be assumed constant is indicated. Natural convection was observed for oblique systems below N 'Ra , while simultaneous horizontal flow did not affect N Racrit. The expected range of values for the various parameters pertaining to segregated forward combustion is indicated and the corresponding values of N 'Ra calculated. Only under very favorable conditions, such as high permeability, high pressure and low top temperature, can the critical value of N 'R, be exceeded. Thickness of the convection layer should not become too large, since the time required to obtain significant mixing is proportional to the square of the thickness. For an oblique combustion frant the conditions for significant mixing may be less strenuous. LNTRODUCTION Laboratory1,2 and field314 experiments have shown that a markedly upgraded oil can be produced by in situ forward combustion. Under certain conditions injected air may move through a high permeability, gas-saturated channel over the oil-saturated layer, while combustion takes place, exclusively, at the horizontal interface (Fig. 1). Such a channel may be a natural gas cap, or it may result from a forward combustion process in which injected air and combustion gases fingered through the top of the formation, causing a premature breakthrough at the production well. In this particular case of segregated forward combustion, the air stream moves parallel to the combustion front. Molecular diffusion and transverse mechanical dispersion will be insufficient to cause all the oxygen in the air stream to reach the combustion front. When the oxygen in the air stream is not completely consumed in the combustion process, it will reach the production well and create a serious fire hazard. In addition, the reduced efficiency may make the process economically unprofitable while also serious corrosion problems may be experienced in the production we11.3 This undesirable situation should, therefore, be prevented. However, in a situation as depicted in Fig. 1, an unstable temperature gradient exists in the gas phase. The combustion is taking place at the lower boundary at a nearly constant temperature that may be anywhere from 600 to 1,200F, depending on the conditions. The upper boundary of the gas phase is overlying, impermeable rock; its temperature might be around 100F, but may increase to 300F or higher due to conduction and convection as the combustion process continues. This represents a steep temperature gradient and it is conceivable that under those conditions free or natural convection will take place in the gas

Jan 1, 1967

LIST OF MEMBERS AND ASSOCIATES ARRANGED ACCORDING TO STATES AND TOWNS. ALABAMA. Aldrich, Aldrich, W. F. Anniston, Noble, A. E Bessemer, Fergusson, V. Bir¬mingham, Aldrich, T. H., Jr, Bowron, C. E, Bowron, J., Davis, F H, Dimmick, F. D., Hillman, Ludwig, C. P., McCarthy, M. E, McCormack, G B., McCrery, Ramsay, E, Shook, A. M. Ensley, McDonald, S., Shook, J. W. Gadsden, Lee, R. H., Jr. Gannts Quarry, Hiller, E Helena, Squire, J. Huntsvalle, Moss Le¬high, Toulmin. Ozmoor, Greenamyer, A. G. Rock Run, Garvin, J M. Selma, Saylor, B. F. A. Sheffield, Miller, D, I. Tuscaloosa, Lodge, J. Woodward, Wood¬ward, A. H. ALASKA Coppermount, Wiswell, H. J. Douglas Island, Macdonald, J Ellamar, Stevens, B. Fairbanks, Hamilton, A L Haines, Le Wald, E A. Jualin, Hoggatt, W. B. Juneau, Denby, Hampton, W. H , Thane, B L , Whipple, J. R. Ketchikan, Bar¬ber, J C , Parker, J. L., Reid, G D Nome, Garfield, C D. Snettwham, Tisdale. Teller, Hirshberg, M. R. Treadwell Caty, Kinzie, Stow, H. P. Valdez, Esterly, G. M, Hazelet.

Jan 1, 1910

By Carmine D. &apos, Lemuel Tarshis, Joel Hirschhorn, Antonio

Vapor-deposited nickel films in the thickness range 700 to 4360A were tested in uniaxial tension utilizing a microtester designed specifically for this study. Contrary to the findings of some investigators, a definite thickness-strength relationship was observed below 3000 A with a four-to sevenfold increase in strength over that of bulk nickel. The films were characterized by high elastic strains and little plasticity. On the basis of these and other reported data, it is suggested that the high strength level in metal films is related to the manner in which they are produced. Vapor deposition, owing to its severe quenching effect. is believed to promote the formation of point defects which inhibit dislocation movement. IN recent years it has been reported that metals, when in the form of thin films, exhibit extraordinarily high strengths. The data published to date have been primarily concerned with silver and gold because of the ease with which these metals can be vapor-deposited and their high resistance to surface oxidation. Previous investigations into the mechanical strength of thin films has uncovered an apparent dichotomy of view on film behavior. Beams and his co-workers have reported a definite dependence of strength on film thickness. Other workers,"-'6 however, in separate studies on the strength of poly crystalline and single-crystal films have found no such thickness-strength relationship. The study of thin-film strength is extremely difficult because of the many variables associated with film preparation, handling, and testing. Moreover, the manner of test employed by different investigators has varied quite radically, ranging from simple uniaxial-tension to biaxial-bulge testing. The work reported herein was conducted in order to determine the mechanical behavior of a structural metal when in the form of a vacuum-deposited thin film and to gain some insight into the reasons for the high strengths exhibited by metals having such a con- figuration. In this study a method of test was chosen which would yield results which are easily interpreted and lend themselves to comparison with properties of the same material in bulk form. Moreover, specimen-preparation parameters and film-handling techniques are set forth so that other investigators can properly compare their findings with ours. EXPERIMENTAL PROCEDURES A) Film Preparation. Vacuum deposition was performed in an 18 by 30 in. bell jar using a standard New York Air Brake Co. vacuum station with a 6-in. oil-diffusion pump. Before evaporation the system was pumped to a pressure of less than 2 x 10"5 torr. A shield was employed to protect the substrates from the emission of contaminants during the critical melting and outgassing of the evaporant. The source consisted of from one to six filaments (0.020 in. diam). The length of each filament was about 5 in. and was placed 6 to 8 1/2 in. from the substrate in such a manner that the substrate face was at 90 deg incidence with respect to the evaporant beam. The temperature of the source was 2000"~ during evaporation. The films were deposited onto a substrate arrangement which was composed of four basic components, that is: 1) a 3 by 1 in. glass slide; 2) a 22-mm sq micro cover glass on 1); 3) a 22 by 50 mm micro cover glass coated with collodion on 1); and 4) a stainless-steel sheet mask containing twelve rectangular openings of 1-mm and 2-mm widths and lengths of 5 mm laid over 3). Thus, test specimens of 1-mm and 2-mm widths are deposited onto a collodion substrate which precludes epitaxial effects in the specirnens. 17-le The rectangular cover glass and square cover glass were positioned in such a manner that a strip of film would be evaporated along the length and across the width of the large glass slide. This boundary of evaporated film was used to determine the film thickness by multiple-beam interferometry. The square cover glass was used for X-ray and chemical analyses. Thickness of the deposits was varied by changing the number of filaments used (one to six). The duration of evaporation was 30 sec for each filamgnt which resulted in a deposition rate of 8 to 20A per sec. Evaporations were all performed at room temperature; however, radiant heat from the source raised the substrate temperature to 40" to 60°C. All substrates were cleaned by ultrasonic agitation in a solution of spectranalyzed isopropyl alcohol. Collodion was deposited on the micro cover glass by immersion in solution of collodion in amyl acetate. B) Thickness Control and Measurement. Film

Jan 1, 1963

APPROXIMATELY 90 per cent of the steel that is melted and refined in the United States and poured into ingots is made in basic open-hearth furnaces, as shown in Table 1-1. The annual ingot capacity of the steel industry reported January 1, 1950, by the American Iron and Steel Institute3* was 99,040,160 tons, of which the basic open-hearth process accounted for 85,896,580 tons, 86.7 per cent of the .total. The capacity of the individual furnaces varies over a wide range, a large majority falling within limits of 50 to 200 tons (Fig 1-1). Most of the units constructed [ ] since 1942 are in the larger size groups, between 175 and 225 tons capacity.

Jan 1, 1964

Aalde, Kaare. ('40) Gen'I Del., Bisbee. Ariz. Aase, Glenn D., ('40) Univ. of North Dakota. Grand Forks. N. D. Abadesco, Enrique A., ('39) College of Engrg.. Univ. of the Philippines. Manila, P. I. Abbott. John L., ('40) Colorado School of Mines. Golden. Colo. Abdul-Ahad, A., ('39) Montana School of Mines. Residence Hall, Butte. Mont. Abreu, Ovidio M., ('38) Univ. of Nevada, Reno, Nev. Acomb, Allen. ('41) Louisiana State Univ., Box 1970, University. La. Acosta S., Gonzalo. ('40) Univ. of Texas, Univ. Sta., Box 1785. Austin, Tex. Adam, Howard W., ('41) Montana School of Mines. Butte, Mont. Adams, Albert, ('381 New Mexico School of Mines, Socorro. N. M. Adams. Charles W., ('39) Michigan College of Min. & Tech., Houghton, Mich. Adams. H. Travis, ('39) 316 South -5th St., Bur¬bank. Calif. Adams, Jack L., ('39) Univ. of Oklahoma, Nor¬man. Okla. Adams. John W., ('41) Colorado School of Mines, Golden. Colo. Adams. Lewis J.. ('39) 402 Del Mar Blvd., Corpus Christi, Tex. Adams, Rob L., ('40) Agricultural & Mech. Col¬ lege of Texas. Box 600, College Sta., Tex. Adamson. Charles R., ('41) Univ. of Utah, Salt Lake City. Utah.

Jan 1, 1941

By Paul A. Filteau

Asbestos ranks among the leading minerals produced in Canada. It is also mined in Russia, Rhodesia, South Africa, Cyprus, Italy, the U.S.A., Japan, China and several other countries. The most abundant variety, chrysotile, and also the most valuable form of asbestos produced, makes up 90% of the world's supply. In Canada, chrysotile is found in the provinces of British Columbia, Ontario, Newfoundland as well as in Quebec, the latter accounting for almost 90% of all the fibre produced in this country. A number of developments emerging this year could make 1968 a record production and export year for Canada's asbestos mining industry. Asbestos fibre consumption in increasing in the U.S., Canada, up 10% to date this year, Japan and in Latin America. Demand in Western Europe is again on the upswing, following a cut-back last year. As a result, shipments from Canadian mines for the first eight months of this year reached some 916,968 tons versus 873,402 in 1967, an increase of 43,566 tons or 5%. Indications are that Canadian asbestos production will for the first time ever top 1.5 million tons in 1968.

Jan 1, 1969

By R. E. Hanneman, A. N. Mariano

In conjunction with the need for accurate volumetric data in the Fe-V system for subsequent use in calculating the high-pressure diagrams, room- and high-temperature X-ray diffraction measurements have been carried out. No previous measurements have been published on lattice parameters or volume changes associated with the a transformation for Fe-V alloys. The existing literature on lattice-parameter data for the a and s phases has been reviewed by pearson1 with considerable uncertainty indicated in the data. In order to obtain a good estimate of ?Va-? for thermodynamic calculations of the a D ?(bee D fee) phase stability, high-temperature vacuum X-ray diffraction measurements were made on an Fe-V alloy of 0.92 wt pet V. The term ?Va-? is the difference of molar volumes of the limiting solubilities of the a and y phases at any given temperature; these values can be calculated readily from the appropriate lattice-parameter data. The equipment used was a commercially available MRC (Materials Research Corp.) high-temperature X-ray camera which was fitted to a Norelco diffractometer

Jan 1, 1964

By R. L. Fleischer, B. Chalmers

In order to observe size effects associated with a grain boundary, aluminum single crystals and bicrystals of various cross-sectional dimensions were deformed in tension. Typical stress-strain curves are presented in conjunction with measurements of the effects of changes in crystal dimensions. Some effects of the growth rate used in preparation of crystals are also described. It is indicated that the macroscopic constraints at a grain boundary are responsible for the most prominent grain-boundary effect, the production of multiple slip. Two measurements of the width of the region of double slip are in agreement. It is concluded that the yield stress of aluminum is affected markedly by the inherent oxide coating. THE general problem to be examined is that of dimensional effects in the plastic deformation of metal crystals. These effects will be termed "size effects" and are here defined as follows: A size effect occurs in a series of crystals if their plastic-deformation properties are a function of crystal dimensions. Clearly then size effects depend on the nature of the boundary conditions imposed on the crystal. Crystal boundaries can be of three types: interphase, inter-crystalline, and free surface. Such deformation effects as are caused by distribution of phases, grain size, lineage structure, and single crystal external geometry are specific types of size effects. This discussion will be confined primarily to grain-boundary and single-crystal size effects, though in practice most "single crystals" not only have a number of small angle boundaries but also have one or more surface phases, so that the boundary conditions appropriate to a free surface do not necessarily apply. Hence, to this extent interphase size effects will be considered. The question of size effects associated with grain boundaries (called here intercrystalline size effects)

Jan 1, 1959

By Herbert Clark Hoover, Lou Henry Hoover

DIFFERENT methods of parting gold from silver, and, on the other hand, silver from gold, were discussed in the last book; also the separation of copper from the latter and further, of lead from gold as well as from silver ; and, lastly, the methods for refining the two precious metals. Now I will speak of the methods by which silver must be separated from copper, and likewise from iron.1 The officina, or the building necessary for the purposes and use of those who separate silver from copper, is constructed in this manner. First, four long walls are built, of which the first, which is parallel with the bank of a stream, and the second, are both two hundred and sixty-four feet long. The second, however, stops at one hundred and fifty-one feet, and after, as it were, a break for a length of twenty-four feet, it continues again until it is of a length equal to the first wall. The third wall is one hundred and twenty feet long, starting at a point opposite the sixty-seventh foot of the other walls, and reaching to their one hundred and eighty-sixth foot.

Jan 1, 1950

By Harry A. Lipsitt, Douglas Y. Wang

A fatigue study in completely reversed axial tension-compression has been perforried on high-purity titanium and on three high-purity alloys of titanium. The alloys each contain approxi7nately 0.75 at. pct of a single interstitial element; carbon, nitrogen, and oxygen, respectivley. The results corroborate a previously published theory which proposed that strain aging under alternating stress was responsible for the fatigue limit behavior of certain alloys. The present data indicate that in these alloys an increasing strain-talline aging effect under alternating stress is provided by oxygen, carbon, and nitrogen, respectively. CURRENT research on the nature of the fatigue limit in metals suggests that the presence of a fatigue limit in metallic materials is a manifestation of strain aging that occurs under alternating stress.lm5 A comprehensive theoretical model based on the above hypothesis has been developed to explain the existence of a fatigue limit.' This model also provides increased insight into several other fatigue phenomena as under stressing, overstressing, and coaxing effects. The theory, as well, provides equal understanding for those cases where no real fatigue limit is observed. Briefly, this theory assumes that the S-N curve for a pure metal is a smooth function of the applied stress, and the effect of adding an element that is soluble (or forms a precipitate) in the pure metal is simply to shift the S-N curve to the right. If the added element confers the power to strain age, the result is a further shift of the S-N curve, this time upward and to the right. Since strain aging is not expected to be a strong function of stress, and since damage per cycle is known to be quite stress dependent, it is to be expected that there will be some limiting lower stress at which the strengthening due to strain aging will balance the damage due to crack propagation. This stress is the fatigue limit. The position of the fatigue-limit knee was thought to be a function of the magnitude of the strain-aging effect on both the finite and infinite life portions of the S-N curve. Although the strain aging hypothesis seems to be reasonably valid for bcc materials,2'6 it needed to be tested for both fcc and cph metals. This report is the first of a series concerning the fatigue-limit behavior of titanium with varying amounts of the interstitial solutes (C, N,, and 4) that are known to cause static strain aging in titanium. Yield-point effects have been reported for polycrys-talline high-purity titanium alloys containing either carbon, nitrogen, or oxygen.7'9 These effects were observed at testing temperatures in the range 100 to 300'. In addition yield-point and strain-aging effects have been reported for single crystals of titanium containing 0.1 wt pct C plus N.' These yield points were observed over a wide temperature range, but no room-temperature aging occurred. Aging at 180' was required to cause the return of the yield point. The magnitude of the yield phenomena in titanium containing interstitials is not expected to be as large as is observed in bcc metals because of several factors. Titanium has a very high chemical affinity for oxygen and nitrogen. The thermodynamic stability of solutions of oxygen or nitrogen in titanium is recognized. Lattice parameter measurements of titanium containing arbon, oxygen,1° or nitrogen" show that the "c" parameter is expanded more than the "a" parameter, but that up to about 2 wt pct this results in an insignificant change of the axial ratio 'c/a." Ehrlich" has shown that the sites occupied by interstitial atoms in titanium are spherically symmetrical and therefore a lattice expansion, at a constant c/a ratio, results in a simple dilation of the interstitial site. Such a dilation involving no shear has been shown to react only with edge components of dislocations.13 This causes only a weak pinning action. Shear stresses would be anticipated locally when only one of the two interstitial positions was occupied. The carbon atom will cause a symmetrical distortion of the lattice whereas the oxygen and nitrogen atoms have, in addition, the previously mentioned chemical affinity of titanium for these elements. These factors will result in a considerably smaller reduction of free energy upon the association of interstitial atoms with dislocations, and therefore a much weaker pinning than has been observed for the bcc metals. These considerations would lead to the hypothesis that of the interstitial elements considered here carbon would cause the strongest pinning effect in titanium where the amount of interstitial in solution is constant. This hypothesis will be borne out in the analysis of the present results.

Jan 1, 1962

By F. J. Plecity, J. T. Michalak, W. C. Leslie

Isothermal recrystallization and grain growth in zone- and vacuum-melted irons and Fe-Mn alloys, up to 0.60 pct Mn, were studied in the range 480° to 650° C, after 60 pct cold reduction. In initial stages, rate of grain growth and rate of recrystallization of iron decrease with time. The recrystallization is typical of a growth-controlled process, and rate of growth is determined by the extent of recovery. Mn decreases rates of growth and of recrystallizatzon. The recrystallization process changes at about 0.30 pct Mn and nucleation may become time-depetzdet~t. In recent years, considerable effort has been expended in determining the effects of solute elements on recrystallization and boundary migration in fcc metals. The results have indicated that the effects produced by single solute additions are dependent upon both the element added and its concentration.'-' In contrast, there have been very few attempts to determine the characteristics of recrystallization and boundary migration in high-purity bcc metals, especially after heavy deformation, and the effects thereon of single solute elements.9-11 This study was undertaken to determine the recrystallization characteristics of various "high-purity" irons and the effects of manganese additions at two levels of base purity. It was hoped that the information obtained would improve our understanding of the recrystallization of pure metals and aid in formulating a theory for the effect of solute elements. The interest was not entirely academic, for the annealing of low-carbon steels, which is of very great commercial importance, is but poorly understood. MATERIALS The compositions of the irons and iron-manganese alloys used are listed in Table I. The zone-melted iron and Fe-Mn alloys were made by Battelle Memorial Institute. Iron S-1 was arc-melted in a water-cooled steel mold in an argon atmosphere. The ingot was forged into a bar, then given two horizontal zone-refining passes in an alumina boat. Iron V-4 was treated in a similar manner, but was not zone-refined. The iron for the zone-melted Fe-Mn alloys was induction melted in vacuum in MgO crucibles and cast into alumina molds. The ingots were forged into bars, machined to shape, and a groove milled down one side of each. The best available electrolytic Mn was placed in the grooves, and the bars were zone melted. The vacuum-melted Fe-Mn alloys were induction melted in this Laboratory in MgO crucibles and poured into cast-iron molds. Iron V-5 was purchased from National Research Corp. in the form of a small vacuum-cast ingot. The low-carbon steel was made by induction melting in air at the U.S. Steel Corp. Applied Research Laboratory. The history of the materials prior to the final cold reduction differed; these details are given in the Appendix. The penultimate grain size of the principal materials was kept in the range ASTM 2 to 4, except for the low-carbon steel. PROCEDURES The cold work prior to the final recrystallization anneal was kept constant at 60 pct. It is known that rolling procedure can influence the kinetics of recrystallization of ironI2; therefore, all specimens were rolled in one direction only, between clean,

Jan 1, 1962

By Armando M. Lago

Secular and cyclical patterns of postwar sources and uses of funds of the mineral sector are analyzed. A simultaneous equation behavior model of sources and uses of funds is developed for both mining firms and integrated producers, and these models were put through the task of predicting the financial and expenditure be-havior of mineral corporations in response to mergers and changes in investment tax credits and depletion allowances. Finally, the quantitative analysis methodology is applied to the analysis of optimum capital structure of mining corporations. The postwar changes that have occurred in the expenditure and financial behavior of mineral corporations are reviewed, particularly the relative importance of factors that affect the industry's supply and demand for funds. This quantitative statistical investigation of factors affecting sources and uses of funds of mineral corporations is achieved through the formulation of a simultaneous equation model of sources and uses of funds. After a description of the study sample, the postwar cyclical and secular financial behavior of mineral corporations is analyzed in detail. An econometric model of mineral corporate financial behavior is formulated. This model is then estimated and reviewed. Policy issues regarding depletion allowances, investment tax credits, and industrial organization of the mineral sector are discussed. Finally, the optimum financial structure of mining firms is discussed and the effect of corporate financial structure on the mining corporations' average cost of capital is analyzed.

Jan 1, 1971

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles L range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola 1 described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes2 in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker3 was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle

Jan 1, 1943

By S. W. Miller

Most of the steel welding done at the present time is in material containing not over 0.3 per cent. carbon, and the tests here described were in similar material. These tests are not as yet completed but it is hoped that more results and more reasons for the conclusions may be presented at the meeting in February. From the time the author found the peculiar structure in electric welds referred to in a previous paper,' that is, needles or plates in the grains and similar material, in larger spots, at the grain boundaries, he has felt that these plates which may be iron nitride and probably contain some carbon, were at least partly responsible for the brittleness of electric welds. He has found but few traces of similar lines in oxyacetylene welds until the last 2 mo., he has since found large numbers under certain conditions. In the top of these welds, they are quite numerous. In the body of heavy oxyacetylene welds, they appear at times, but not nearly to the extent that they do in electric welds; the author has never seen them in the body of welds in material less than % in. (19 mm.) thick. They are shown in Fig. 82. The reason they were not noticed before is undoubtedly due to the fact that in making tests of welded pieces the weld was always ground off level with the plate, and as this structure only appears in the top 1/16 in (1-5 mm.) of the weld, they were removed by the grinding or machining; also, welds 3/4 in. thick had not been examined. It did not appear, in making bending tests, that this structure had much influence on the strength of oxyacetylene welds; while electric welds are noticeably brittle. Further, oxyacetylene welds made with certain special materials were exceedingly brittle even after the tops of the welds were removed; this was true in cases where there was no sign of the plates whatever and where the welds were remarkably free from oxide and the other usual defects. It appeared, therefore, that this brittleness did not depend on any variable that had been noticed so far, and it was decided to find where the rupture occurred in various kinds of welds made

Jan 1, 1920

By E. H. Jr. Dix

THE consideration of alloying elements for aluminum has led to a series of investigations of the equilibrium relations between aluminum and those alloying elements. Therefore, the aluminum end of the aluminum-antimony diagram has been studied. The general form of the aluminum-antimony equilibrium diagram has been worked out by Campbell and Mathews1 and by Tammann.2 Campbell and Mathews described principally the beginning of solidification. They found the curve of beginning of solidification to rise gradually from the melting point of pure aluminum to a maximum at about 67 per cent. aluminum. After a slight lowering of the curve at a little greater antimony concentration the curve again rises to a maximum at 18.4 per cent. aluminum, which corresponds to the compound AlSb. The curve then drops to the melting point of pure antimony. Tammann explained the maximum occurring at about 67 per cent. aluminum as the result of the slow formation of the single compound AlSb. The space lattice of the compound AlSb, according to Owen and Preston,3 is face-centered cubic, the antimony atoms being intermeshed with an identical aluminum lattice. Very little, if any, work has been done on aluminum alloys containing small amounts of antimony.

Jan 1, 1930

By L.W. Eastwood, Arthur E. Bousu, C. T. Eddy

The recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presentcd in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers. Since the literature on the subject has been adequately and frequently reviewed, the only referenccs to it in this paper will be those necessary in the discussion of the data presented.

Jan 1, 1935

By Arthur E. Bousu, C. T. Eddy, L. W. Eastwood

The recrystallization and grain-growth phenomena of cold-worked metals have considerable industrial importance because of their role in the fabrication of metals. For this reason, and because of the general academic interest in the subject, these processes have received considerable attention since the time of J. E. Stead's paper1 on The Crystalline Structure of Iron and Steel. There are considerable differences of opinion regarding the theory of recrystallization and grain growth and also differences in the observation of the modus operandi of the processes themselves. The value of many of the existing quantitative data on grain growth is decreased by the failure to distinguish between the grain sizes just after complete recrystallization and those resulting from coalescence. For this reason also, the value of the diagrams of stable grain sizes, like those produced by Bass and Glocker2 and Czochralski3, is lessened in so far as an interpretation of the facts of recrystallization is concerned. It is hoped that the data presentcd in this paper will help to clarify and to simplify the facts relating to recrystallization, and at the same time will show that some of the present-day conceptions are untenable. A paper on the theory of recrystallization, with additional data, will be completed in the near future by the writers. Since the literature on the subject has been adequately and frequently reviewed, the only referenccs to it in this paper will be those necessary in the discussion of the data presented.

Jan 1, 1935

By Auguste J. Rosh

The use of titaniferous ores in the blast-furnace has been the subject of much controversy for many years. Divers objections have been raised against them, and, for one cause or another, the verdict

Jan 1, 1893

By W. C. Hagel, J. H. Westbrook

Usittg a sectioning technique with Agl10 as the tracer, the diffusion of silver in silver-excess (45.8 at. pct Mg), near-stoichiometric (49.8 at. pct Mg), and magnesium-excess (52.0 at. pct Mg) cylinders of CsCl-type AgMg was determined from 500" to 700°C. Diffusion coefficients conform to the expression D = Do exp (-q/RT) where the respective Do values are 1.53, 0.280, and 0.134 sq cm sec-I and the Q values are 41.3, 40.6, and 38.0 kcal g-atom-'. Lnttice-parameter and density measurements were performed on a more numerous assortment and wider range of compositions. Substitutional defects were found on both sides of stoichiometry. Activation energies for other rate processes in these alloys show related trends with changing composition, although silver may not be the rate-detemining species. KNOWLEDGE of diffusion coefficients is necessary for a quantitative understanding of the many rate processes (e.g., grain growth, precipitation, sintering, oxidation, or mechanical deformation) occurring in solids. Although these data are available for most metals and common alloys, they are quite limited for intermetallic compounds—a group of materials whose unique physical and mechanical properties are presently attracting great interest. From a fundamental viewpoint, diffusion in intermetallic compounds also offers several engaging aspects owing to: their ordering, the possibility of introducing large, stable concentrations of lattice defects, and the variety of bonding types and crystal structures which can be found. In the case of CsC1-type compounds, some previous work has been directed at examining the role of vacancy defects by changing their concentration compositionally. The diffusion of Co60 was measured in 0 NiAl1- and in P COA., Except for the results of Smoluchowski and Burgess, isothermal diffusion coefficients were found to pass through a minimum at the stoichiometric composi- they decreased sharply on what was reported by Bradley and co-wrkers' to be the vacancy-rich (aluminum excess) side of stoichiometry. This investigation of the diffusion of Agl110 in AgMg was undertaken both as an adjunct to a concurrent study of its deformation behavior and for the purpose of obtaining information on the influence of lattice defects and temperature on diffusion in another CsC1-type intermetallic compound. Bcc AgMg remains ordered up to and melts congruently at 820°C. Solubility limits at 300°C are about 41 at. pct Mg and 53 at. pct Mg. It is one of the Hume-Rothery electron compounds with a 3/2 electron-atom ratio. Previous investigations of its properties include hardress,' tenile,'-' electrical reistivity, and thermodyna-mic1',14 studies. Indications of a high bonding strength may be found in the large heat of mixing1' and in the 6-pct vol contraction on compound formaticp, as calculated using atomic radii of l.40 and l.55a for Ag and Mg. EXPERIMENTAL PROCEDURE Alloys were prepared by the induction melting of selected fine silver (99.95) and low-iron magnesium (99.95) in magnesia crucibles under 1 atm of A. Supplied by the Handy and Harmon and Dow Chemical Cos., respectivelv. Melts were poured under argon into graphite molds providing 1 1/8-in.-diarn. by 4-in.-long ingots. These were homogenized in evacuated and argon-filled fused-silica capsules by heating for 16 hr at 750'. Three 1 in.-diam. by 3/4-in.-long cylinders were machined from the mid-portion of each ingot for diffusion measurements. Three alloys, analyzing 45.8, 49.8, and 52.0 at. pct Mg were taken as representing the extremes of interest, with 49.8 at. pct Mg being very close to the stoichiometric composition of 50.0 at. pct Mg.

Jan 1, 1962