Search Documents

By D. C. Holloway

Ceramic projectiles made from 94% to 99% alumina with a nominal mass of 3.1 gms were fired into granite blocks. The average compressive strength of the ceramic was 800 MPa and that of the rock was 135 MPa. Flat, ogive, conical and pyramidal nose shapes were evaluated at velocities ranging from 450 to 1400 m/sec. It was found that the conical and pyramidal nose shapes at the higher velocities did a significant amount of damage to the rock. On the average, they removed 10 5mm3 of rock and were six and ten times better than the flat and ogive nose shapes. It was also observed that increases in volume occur in discrete steps. This process is highly dependent on the ability of the projectile to penetrate the rock.

Jan 1, 1984

By J. B. Cohen

EARLY investigators1-4 reported that additions of beryllium to silver caused embrittlement. The in-termetallic phases which are now known to exist5,' were not known at the time. Solidification appeared to occur by a simple eutectic reation.4,7 (The primary beryllium-rich phase appeared globular, when the liquidus temperature was near the melting point of pure beryllium, and angular when the liquidus was much lower; in discussion of Sloman's work,4 it was suggested that this difference was due to an intermetallic compound which was not revealed by the polishing technique.) In the investigation reported here, it was found that if the compounds now known to exist were avoided, certain beryllium-silver alloys containing large amounts of the primary beryllium phase possessed sufficient ductility to be cold formed. Alloys containing 14 and 20 at. pct Ag were prepared from vacuum-cast beryllium containing 1.0 to 1.2 pct impurities and silver, 99.99+ pct pure. The elements were melted together by induction in beryllia or alumina crucibles under argon at less than 1 atm pressure. The cooling rate was adjusted by regulating the temperature of the melt and by reducing the power to zero without stopping the water flow in the induction coils, which were in contact with the crucible. Ingots were about 0.75 in. in diam with a grain size of 0.12 to 0.25 in. Microscopic investigation of transverse or longitudinal sections of an ingot cast from a temperature well above its melting point showed that, in general, the compounds did not form, presumably because of rapid cooling; the alloys consisted of beryllium-rich particles in a silver-rich matrix as shown in Fig. 1. A eutectic structure was not observed, probably .due to the low beryllium concentration of the eutectic composition and eutectic divorcement. Within a given grain, the small globules of the primary phase were all oriented in the same direction, as indicated by examination under polarized light; the orientation varied from grain to grain. This suggested that the globules were branches of the same dendrites. If cooling was too slow, a third constituent was observed in the microstructure; because it formed around the primary beryllium-rich globules it was Fig. 1—Ag-Be alloy, 18.6 at. pct Ag, as-cast. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction. probably the 6 compound. A thin ring around an ingot often contained this constituent. When this compound was present in large quantities, or the silver segregated so that large regions occurred with the beryllium-rich globules in contact, sections from the ingot were brittle. When the compound was initially absent, it was possible to carry out reductions in thickness of 50 pct by cold rolling with only limited edge cracking; failure did not occur until reductions of 80 pct. A typical cross section after cold rolling is shown in Fig. 2. After simple bend tests, microcracks were found; these apparently were difficult to propagate in the two-phase structure, as the specimens continued to behave in a ductile manner after the cracks appeared. Similar cracks would probably be closed during rolling. It is apparent in Fig. 2 however, that the primary beryllium particles undergo extensive plastic deformation. Hardness values of the alloys indicated that some work-hardening occurred during cold working. Fig. 2—Ag-Be alloy, 18.6 at. pct Ag, reduced 83 pct in thickness by cold rolling. Bright field illumination. Etched with an aqueous solution of NH,OH and H2O2. X500. Reduced approximately 21 pct for reproduction.

Jan 1, 1961

By R. I. Garrod, R. A. Coyle

The shapes and positions of X-ray reflections from specimens of copper, steel, and aluminum alloy haue been examined in the elastic and plastic ranges both while the specimen was under stress and in the unloaded condition. For the aluminum alloy the shape was unaltered by the application of stress either within the elastic limit or in the plastic range provided that no additional plastic strain was induced. In copper the broadening accompanying plastic deformation was very slightly reduced when the specimen was unloaded. A similay but more marked elastic component of broadening was also found for steel, but in this case below the yield stress. Line profiles corrected for instrumental and particle-size broadening indicate very large internal stresses in local regions of the plastically deformed metals. The results are discussed in terms of a recent suggestion that the heterogeneous dislocation distribution between the cells and their boundary walls plays a major role in the peak shifts and broadening of the X-ray reflections. STUDIES of the X-ray line profiles from strained polycrystalline aggregates concentrate usually on one or the other of two main parameters: a) the displacement of the peak of the intensity contour from its position for a strain-free aggregate, or b) the shape of the profile. From peak shifts data can be obtained either on the relation in both the elastic and plastic ranges between applied external stress and average lattice strains in a given (hkl) direction, or, alternatively, on the residual lattice strains which are present after a plastically deformed specimen is unloaded.' On the other hand, the shapes of the broadened profiles from cold-worked metals can be analyzed to separate the broadening produced by small particle size and by heterogeneous lattice strains.' In this paper the terms "size broadening" and "strain broadening'' are used in the general sense adopted by warren.' In the past, apart from two early qualitative observation, it has been customary to examine only the movements of the peaks of the profiles while the specimen is actually under load, since the line broadening induced by plastic strain remains after removal of the external stress. Consideration of the implications of existing data of this type suggests, however, that fruitful additional information on a number of fundamental aspects might be gained by careful examination of whether the X-ray line profile is in fact different in the loaded and unloaded states of the specimen. By taking advantage of the sensitivity and convenience of modern diffractometer techniques it is possible to explore with relative ease the magnitude and importance of any elastic effects which may be superimposed upon the well-known permanent changes in profile. The main aim of the work to be described was thus to investigate this point for typical metals and alloys. For this purpose annealed specimens were extended first elastically and then plastically and the positions and shapes of X-ray reflections were recorded. Initially it was anticipated that prime interest would center on observations within the plastic range; it has been found, however, that small changes in profile sometimes occur both before and after the nominal elastic limit of the material is reached. It is shown that the results obtained have important implications in relation to the structural changes and processes associated with deformation. I) EXPERIMENTAL To enable the diffraction lines to be recorded while the specimen was under uniaxial-tensile stress, a small hydraulic testing machine was designed and constructed for direct attachment to the goniometer of a Philips diffractometer. The specimens, which were machined from 1/2-in.-diam rod and had a central rectangular section 3/8 by 1/16 in. over a gage length of 1 in., were held in the machine by split collets mounted in grooves in the cylindrical ends of each specimen. No special precautions were taken to ensure precise axiality of loading. Constant oil pressure was maintained by a lever and weights system and transmitted to the loading rig by flexible pipe. The actual load on the specimen was measured by a load cell in the machine to an accuracy of * 1 pct. To enable smooth X-ray profiles to be obtained the specimen and machine were oscillated continuously during recording through *7-1/2 deg about the normal half-angle position of the goniometer. The three materials chosen for the investigations were high-purity copper as representative of a ductile fcc metal, a low-carbon steel for a bcc metal, and an aluminum alloy as a material in which the proof stress/ultimate strength ratio is high. Details are as follows. a) Copper. 99.999 pct purity. After machining the specimen surface was polished mechanically and

Jan 1, 1964

Graham Macfarlane, Louisville, Ky. (communication to the Secretary*):—In the paper by S. Whinery under the above caption mention is made of the occurrence of Clinton iron-ore in Kentucky and Tennessee. I believe that this is really a ferruginous limestone in what the Tennessee Geological Survey calls the Fernvale formation. In Davidson and Sumner counties, Tennessee, this occurs at about the horizon stated by Mr. Whinery. The maximum thickness of the deposit is from 10 to 12 ft., but it averages between 6 and 8 ft., lying practically horizontal. The Red River Furnace Co., under my direction, opened a mine in the Fernvale " red rock" near Goodlettsville, Tenn., several years ago. When it was first found we assumed it to be Clinton ore, but the absence of the characteristic Clinton fossiliferous structure and other evidence satisfied us that it is really limestone saturated with iron oxide. I think the very low ratio of SiO2 and Al2o3 to iron content as compared with the usual ratio in the Clinton ore is also evidence in favor of its being the Fernvale. The Tennessee Geological Survey states that at outcrops where this ore has been leached it carries about 44 per cent. of iron; under cover, from 20 to 25 per cent. of iron and from 3 to 6 per cent. of silica, the remainder being chiefly calcium carbonate. Its phosphorus content is irregular and generally rather high for a foundry-iron mixture. Since it is more than self-fluxing, we have at times operated with a mixture of brown hematite and red ore with no limestone.

Jan 1, 1913

By J. S. Kirkaldy, D. G. Fedak

The extra degree of freedonz introduced by a second independetzt concentration in a tenzary system gives rise to the possibility of unstable planar phase interfaces in semi-infinite diffision layer couples. Diffusion paths which pass continuously in and out of too-phase regions of the phase diagram but which are not coincident with tie-lines give rise to super saturated zones which may be either adjacent to or isolated from planar phase interfaces, with corresponding nonisolated or isolated precipitates. Nonisolated precipitates are equivalent to morphological development of the interface. Selected couples in the ternary systems Fe-Ni-Cr and Cu-Zn-Sn have been examined nzetallographically and ifz the latter case both isolated and uo~zisolated precipitates have been observed. The diffusion path in one of the couples showing interface morphological developtnent has been examitled using electron probe microanalysis. IGNORING the spurious effects of preferential grain boundary diffusion and anisotropic crystal growth7 it can be unequivocally stated that it is impossible for a binary isothermal diffusion couple constructed of two unsaturated phases to sustain a nonplanar phase interface. Consider for demonstrative purposes the schematic phase diagram of Fig. l(a). Given an initial flat phase interface, semi-infinite boundary conditions and the internal boundary condition fixed by the constitution diagram, xB = xB(T), the unique solution of the diffusion equation requires a persistent flat interface. No other solution is possible. If, however, we anticipate the involvement of surface tension, then the internal boundary condition must be written xB = xB (T,Y) where r is the radius of curvature of a hypothetical nonplanar interface. The introduction of a new parameter such as r can be equivalent to the release of an internal constraint, so that a stable nonplanar interface may be possible after all. Consider a perturbation to the interface as indicated in Fig. 1(b). According to the Ostwald-Freundlich equation: which is applicable to a system of this constitution, the solubility of A in the matrix ß ,xB (Y), at a point of curvature r is given by where Va is the molar volume of the a-phase, R is the gas constant, and a is the interfacial tension. Since the right hand side is positive, xB(r) >xB cm, as indicated in Figs. 1(a) and 1(c). Accordingly, the perturbation will carry the interface concentration in a direction which is opposite to that which would sustain local equilibrium. Such a perturbation is necessarily moderated and the system is returned to its initial condition. This result is general for all binary couples since we can regard an interfacial perturbation as an attempt to precipitate within un-

Jan 1, 1962

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By P. E. Doherty, B. Chalmers

Subboundaries may be revealed in aluminum by the formation of pits on the surface during cooling from elevated temperatures. The pits do not form in the vicinity of high- or low-angle boundaries. They are attributed to the condensation of vacancies from a super saturation produced during coolirzg. Using the vacancy pit and Schulz X-ray techniques for observing low-angle boundaries, a study was made of the transition from the nearly perfect seed to the striated structuke characterist-ic of aluminum crystals grown from the melt. It was found that the individual striation boundaries develop by the coalescence of very small-angle boundaries, as well as by the addition of individual dislocations. Several mechanisms for the formation of striations are discussed. Evidence was found suggesting that a super-saturation of vacancies exists near a growing interface, and it is proposed that the resulting climb of existing dislocalions produces "half'-loops" at the interface, which combine to form the low-angle striation boundaries. LINEAGE, or "striation" boundaries, have been studied in detail by Teghtsoonian and Chalmers 1,2 in crystals of tin grown from the melt, and by Atwater and Chalmers3 in lead. They found that single crystals grown from the melt consist of regions which are separated by subboundaries that lie roughly parallel to the growth direction. A difference in orientation of 0.5 to 3 deg exists between the striated regions; the misorientation is such that the lattice of one region could be brought into coincidence with the lattice of its neighbor by a rotation about an axis approximately parallel to the direction of growth of the crystal. They observed an incubation distance for the formation of striations which increased with decreasing growth rate. They also found that in any crystal, the sum of all rotations of the lattice in one sense, in going from one striation to the next, is very nearly equal to the sum of all the rotations in the opposite sense. A striation boundary, which is a low-angle grain boundary, can be described as an array of dislocations. If it is assumed that suitable dislocations are introduced into the crystal during solidification, the formation of striation boundaries can be explained as a result of the migration of the disloca- tions into arrays. The formation of arrays is energetically favorable since the energy of an assembly of dislocations can be reduced by the interaction of the stress fields when a suitable array is formed. This investigation presents and interprets new information concerning the nature and origin of striation boundaries in aluminum. EXPERIMENTAL TECHNIQUE Single crystals of high-purity aluminum (Alcoa 99.992 pct) were prepared by horizontal growth from the melt.'' The specimens were subsequently electropolished in a solution of 5 parts methanol to 1 part perchloric acid kept between -10° and 0°C in a bath of dry ice and alcohol. The current density was approximately 6 amps per sq in. Doherty and Davis9 have shown that in aluminum sub-boundaries with misorientations of not less than several seconds of arc may be revealed by the vacancy pit technique. During cooling from elevated temperatures pits form on electropolished surfaces of aluminum crystals as a result of the condensation of vacancies.11 Pits do not form in the vicinity of small- or large-angle grain boundaries, presumably because such boundaries act as sinks for vacancies. Boundaries of misorientations down to 3 sec of arc are revealed as pit-free regions, see Fig. 1. The Schulz X-ray technique12 was used to determine the angular misorientations of subboundaries. In this method, white radiation from a micro-focus X-ray tube is used to produce an image of a fairly large area of a single crystal surface. Subboundaries cause splitting in the diffracted image, see Fig. 2. Misorientations down to about 15 sec of arc may be observed with this technique. OBSERVATIONS AND DISCUSSION Figure 1 shows a striated aluminum crystal grown at 10 cm per hr etched by the vacancy pit technique. An incubation distance of about 1 cm is observed before the initiation of striation boundaries. Fig. 2 is a Schulz X-ray photograph of a striated crystal similar to that shown in Fig. 1. A large area of the crystal was studied by means of a series of photographs. Fig. 2, which is a reflection from the (100) plane, included about the first 4 cm of crystal to freeze. There is an incubation distance of about 1 cm, and a distance of about 2 cm over which the angle of misorientation builds up to its final value of approximately one degree. Some twist component can be seen in Fig. 2 at the right side of the photograph. From Fig. 2 it can be seen that the sum of all rotations of the lattice in one

Jan 1, 1962

By Arnulf Muan, Carlos Landolt

Equilibria involving Cu-Pt alloys, copper oxides, and atmospheres of known ox2gen pressures have been determined at 1000' and 1200 C. The data obtained have been used to calculate activity-composition relations in the alloys. A moderate negative deviation from ideality is found. At high copper concentrations, the results of the present study are in good agreement with those of previous investigators, whereas at low copper concentrations the activities obtained in this investigation are slightly higher than those reported previously. The present study is part of a research program dealing with the determination of phase relations and thermodynamic properties of copper-containing systems at high temperatures. The information available for such systems is very scanty, particularly for copper oxides and their combinations with other oxide components. Platinum is commonly used as a container in studies of oxide equilibria. To evaluate quantitatively the extent of reaction between the oxide and the container, a knowledge of activity-composition relations in Cu-Pt alloys is necessary. Such data are not available for Cu-Pt alloys in the temperature range of particular interest in the present research program, and particularly for alloys low in copper. Studies of various aspects of the systems Cu-Pt and Cu-0 have been reported in previous literature. The system Cu-Pt is known1 to form a continuous solid-solution series above 812.C, whereas ordered phases are present in certain composition ranges at lower temperatures. Thermodynamic data for the system have been reviewed by Hultgren et al.,' who presented free energies of mixing at 65Oo C, mainly derived from electromotive force cell measurements by Weibke and Matthes.3 Enthalpies of mixing at 640°C have been obtained by Oriani and Murphy4 with liquid tin calorime-try. Their results differ considerably from those derived from the temperature dependence of the data of Weibke and Matthes. Thermodynamic data for the disordered alloys have been obtained by Assayag,5 and more recently by Schmahl and Minzl,6 by Myles and Darby,7 and by McCormack, Myers, and Saxer.8 The two latter sets of data7'' became available after the present study was completed. In the system Cu-0+ two oxides are stable at high temperatures, CuO and CuzO+ each having only minor deviations from stoichiometry. Equilibria in the liquidus temperature region of the system Cu2O-CuO have been studied by Roberts and systemsmyth,9'10CuzO-CuO by Vogel and ocher,I1 by Osterwald,12 and recently the the present authors.13 The system is of the eutectic type with a eutectic temperature of 1083.C The composition of the eutectic liquid corresponds to Xcu0 = °.44, and the oxygen pressure of the coexisting gas phase is Po2 = 0.55 atm.13 Equilibrium oxygen pressures for coexistence of solid CuO and solid Cu2O have been determined by Schmahl and Muller,l4 by Gadalla, Ford, and white,l5 by Bidwell,16 and recently by the present authors.13 There is reasonably good agreement among the various sets of data. Free energies of formation of Cu2O(s) from the elements have been derived by Tretyakov,17 by Bidwell,16 by Kiukkola and wagner,18 by Pal'guev and Neuimin," and by Steele and Alcock,20 There is particularly good agreement among the latter three1'-20 sets of data. THEORETICAL BASIS Consider a subsolidus isothermal section of the system Cu-Pt-0, as shown in Fig. 1. Two phase as-

Jan 1, 1970

By J. Chipman, N. J. Grant, R. Rocca

Desulphurization of liquid iron by reducing slags of the electric-furnace type was studied from 65 heats. Variations were made in basicity over a wide range and in FeO up to about 5 pct for their effects on desulphurization. The role of FeO in desulphurization from the blast furnace, to the electric furnace, to the oxidizing conditions of the open hearth is shown to fit a relatively simple pattern of behavior. THE mechanism which controls the desulphurization of molten iron by basic slags has been the object of several investigations. In particular, equilibrium determinations have been made both in the field of basic open-hearth slags, which have a high iron-oxide concentration, and in the field of blast-furnace slags which have a very low iron-oxide concentration. In both cases the desulphurization ratio has been found to increase with increasing basicity of the slags; however, the mechanism of desulphurization differs in the two cases. In basic open-hearth slags desulphurization occurs mainly as a partition of iron sulphide:&apos; FeS * (FeS) and the desulphurization ratio is approximately independent of iron-oxide concentration in the slag. In blast-furnace slags the concentration of iron oxide is very low as a result of the highly reducing conditions in which they are formed. The controlling reaction for desulphurization is then:2,3 FeS + (CaO) <=* (CaS) + (FeO) The slags of the reducing stage in the electric furnace have an iron-oxide concentration which is intermediate between blast-furnace and open-hearth slags. The study of the mechanism of desulphurization for these slags has been the object of this investigation. The importance of low (FeO) in the slag for desulphurization was first verified by Bardenheuer and Geller,& who found that high desulphurization ratios were obtained in highly reduced slags. It was recognized" hat iron oxide in the slag becomes a controlling factor in desulphurization only at FeO concentrations approximately under 5 pct. A recent investigation conducted by Buehl,7 upon the suggestion of one of the authors, confirmed this opinion from the results obtained from a heat conducted in a small arc furnace. In the present investigation, slags of very high basicity, such as often are encountered in the basic electric furnace, could not be studied, but equilibrium data have been obtained for slags in a wide basicity range. The iron-oxide concentration in these slags ranged from 0.08 to 15 pct and was controlled by the addition of silicon to the metal. Other constituents of the slags were mainly CaO, MgO, SiO2, A120,, and CaF,. The experimental technique was essentially the same as that of previous investigations.1 8-lo In an open magnesia-lined induction furnace, 65 lb of Armco ingot iron was melted. An atmosphere of hydrogen was maintained over the melt for 1 hr to bring the carbon content down to approximately 0.010 pct maximum. The bath then was exposed to air for 25 min to remove hydrogen. The electrodes were put in place, and the furnace was operated from this point on in an atmosphere of nitrogen. A synthetic slag was added to which additions of silicon and iron sulphide were made. A rate study conducted at the beginning of this investigation had

Jan 1, 1952

By R. B. Sosman

INTRODUCTION IT is well known that ferric. oxide, Fe.-,03, is paramagnetic, while magnetite, Fe304, is classed among the highly ferromagnetic substances. But magnetic data on oxides intermediate in composition between Fe-03 and Fe304 have been almost completely lacking. Fe203 and Fe304 form a solid-solution series, according to present evidence.&apos; In this series the properties change continuously from Fe203 toward Fe304, as the percentage of FeO increases from zero toward 31.03, which is the percentage in magnetite. It is possible that there is a break in the series near Fe304, but it has not yet been possible to establish the existence-of such a break experimentally. The occurrence of solid solution ill this series is shown by the dissociation pressure, or oxygen pressure in equilibrium with the oxides, which falls continuously over the range from Fe203 to Fe304. The oxygen-pressure curves at 1,100° and 1,200° are shown in Fig. 1. The existence of solid solution is also demonstrated by the continuous change in optical properties from Fe203 over to a composition containing about 18 per cent. FeO, at which point the opacity of the oxide becomes so great that it is im-possible to obtain measurements at higher percentages of ferrous iron. Natural oxides of iron intermediate in composition between Fe2O3 and Fe304 are much more common than is generally supposed. If a mineral oxide is not strongly attracted by a small hand magnet and if it gives a red streak, it is usually labeled "hematite." If it is strongly attracted by the hand magnet it is usually labeled "magnetite" without further tests. As we shall show later, oxides containing from 1 up to 31 per cent. FeO can be thus erroneously lumped together as "magnetite." It is a fact, nevertheless, that the great hulk of natural oxides of iron lie fairly near either Fe203 Or Fe304 in composition. The reason will be

Jan 6, 1917

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By T. R. Armstrong

Total crude oil production in Mexico in the year 1941 is estimated at approxi- mately 41,000,000 bbl.; a daily average of 112,700 bbl. and a decrease of about 5 per cent as compared with the daily average of 120,000 bbl. produced in the year 1940, and nearly 11 per cent decrease as com-

Jan 1, 1942

By D. E. Hartman, J. M. Roberts

A detailed study of the temperature dependence of the critical stress, TB . necessary to cause a damping loss of 1.41 x 10-6 g mm per mm3 in pre-strained magnesium single crystals has been carried out in the temperature range 82" to 320°K. Tb is found to be linearly related to the reciprocal of the ahsol~cte temperature in this temperature range. The temperature dependence of the anelastic limit, TA, defined as the stress necessary to form open unidirectional stress-cycle damping loops has been measured between 82" to 320°K. ta is found to be independent of temperature in this range. It is suggested that TA is determined by the stress necessary to activate Frank-Read dislocation NUMEROUS studies1-9 have been reported concerning the details of yielding and microstrain near and below the generally discussed macroscopic flow stress. The work of Kramer and coworkers10-13 is helpful in determining certain qualitative facts. concerning preyield phenomena. The absence of a stress-dependent delay time in annealed copper and aluminum single crystals between 83" and 298 suggests that the preyield mechanism is temperature-independent in this range. This is not sources. The temperature and stress dependence of the effective activation volume (Veff) has been measured in the damping-loop region in prestrained magnesium single crystals. The data suggests that Veff/kT is approximately constant, equal to 2 4.5 sq mm per g in the temperature range 130°to 298°K, and that Veff is almost independent of stress at stress levels greater than 10 g per sq mm. A restricted model is developed to predict the stress (rb) necessary to cause a small fixed damping loss as a function of temperature, effective activation volume, and dislocation density. Various possible dislocation mechanisms controlling TB are discussed. true for zinc, p brass, and iron crystals in the same temperature range, however, since the existence of a stress-dependent delay time suggests a thermally activated preyield mechanism in these materials.10-13 The work by Vreeland et a1.14 confirms the work by Liu et al.ll on delayed yielding in zinc single crystals. A stress-dependent delay time between 82" and 298°K was found12 in prestrained aluminum and copper crystals. These results suggest that the preyield phenomena may be different between prestrained and unstrained or annealed crystals. The temperature dependence of the yield point at 2 x 10-8 plastic strain found by Rosenfield and Averbach3 in annealed copper and aluminum is not in agreement with the delay-time data, unless possibly the delayed yielding experiment only de-

Jan 1, 1964

By Donald L. Katz, Leo B. Bicher

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By Leo B. Bicher, Donald L. Katz

A correlation is presented for predicting the viscosities of light paraffin hydrocarbon mixtures such as natural gases for temperatures from o° to 4o0°F. and for pressures fro1 atmospheric to I0,000 lb. per sq. in. The correlation is based on the viscosity data for the methane-propane system and requires only a knowledge of the molecular weight of the naturaI gas. The viscosities of natural gases reported in the literature up to 2500 lb. were reproduced by the correlation with an average deviation of 5.8 per cent. Introduction The viscosity of a natural gas is required whenever calculations are made of the pressure drop that occurs while the gas flows through pipes or porous media. Methods of predicting the viscosities of gases at the present operating pressures are not available. This paper presents a simple method of predicting the viscosity of a natural gas in the single-phase region from its molecular weight, temperature, and pressure. Viscosity oF Methane-propane Mixtures The viscosity of methane, propane, and four of their binary mixtures, 20,40, 60, and 80 mol per cent, have been determined for pressures from 400 to 5000 lb. per sq. in. and temperatures from 77" to 437 F., with an experimental accuracy of 3.2 per cent.2 The apparatus used in the investigation was a modification of that employed in previous studiesaJ4 on the viscosity of normal paraffin hydrocarbons. It consists of a viscosimeter of the rolling-ball, inclined-tube type,5>k7 with auxiliary equipment for making up and charging binary mixtures into the viscosimeter.~ The viscosity data on the methane-propane mixtures have been plotted as a function of molecular weight with lines of constant pressure, charts of constant temperature in Figs. I to 3. These charts are extrapolated at temperatures below 77°F. and at pressures above 5000 lb. per sq. inch. Prediction OF Viscosity from Molecular Weight of a NaturaI. Gas At atmospheric pressure the viscosity of light hydrocarbon gases increased with increased temperature, contrary to the change of viscosity of liquids with temperature. The atmospheric viscosities of the normal paraffin hydrocarbons have been determincd by several investiga-tors 3,4,9,10,12,15,16,17,19 and are plotted in Fig. 4 as a function of molecular weight, with extrapolation to 896&apos;F. and to 220 molecular weight. Data for isopentane and normal pentane show less than 2 per cent difference in viscosity, indicating that Fig. 4 can be used for isomeric parafin hydrocarbons with an accuracy of approximately 2 per cent. Trautz and Sorg&apos;7 determined the atmospheric viscosities 01 methane-propane mixtures and showed that they are proportional to the molecular weight. The viscosities of these mixtures

Jan 1, 1944

By D. J. Carney, R. L. Stephenson

M. O. Holowaty (Inland Steel Co., Chicago)—Messrs. Stephenson and Carney should be commended on the presentation of this very interesting paper. They have introduced new ideas on sampling of sinter and have thereby made a valuable contribution to the qualitative evaluation of sinter. The paper undoubtedly presents a novel approach to the problem of sinter sampling and this is to be regarded as its main value. Sampling of sinter from the pallets prior to the discharge is by no means new. This sampling procedure was used in the past by Philbrook; Hamilton and Ameen and others. The sampling basket used by the authors of this paper, however, permits one actually to obtain a good sample of the sintering mixture. The basket which can also be described as a removable pallet goes then through the entire process of sintering and thus offers a sample which is positively representative of the batch in question. The authors&apos; method of evaluating physical properties of sinter seems to be not altogether clear, however. It is felt that the following points should be clarified: I—In the section describing the shatter test the authors state that a 5-lb sample was used in the actual tests. There is no mention of the initial size of sinter particles used and the method of obtaining this 5-lb sample from the sinter cake weighing about 100 to 120 lb. It is also surprising that the sample was dropped from a height of 3 ft instead of the conventionally used 6 ft. Unfortunately there is no mention of the number of drops to which the sample was subjected. 2—The tumbler test used by Messrs. Stephenson and Carney in testing the samples of iron ore sinter was performed in a standard ASTM coke tumbling drum. The drum measures 3 ft in diam and is equipped with two 3-in. lifter bars. The distance of fall in this testing drum is identical with the distance used in the previously described shatter test. The number of drops in the tumbling drum is approximately double the number of revolutions. The basic difference then between the drop-shatter test used by Stephenson and Carney and the tumbling test seems to be the number of drops to which the sample is subjected and the abrasive action to which the sinter particles are exposed in the rotating drum. In any case, the choice between the shatter test and the tumbler test seems to be only a matter of taste and convenience. 3—The authors of the paper state that "in order to insure getting results that were representative . . . the entire sample obtained by means of the sampling basket was used as the starting material for the tumbler test. If the sample broke in pieces, all the pieces were used regardless of their size." The initial size of the material is known to be a very important factor, influencing seriously the final size of the particles. This should be particularly important in case of hard sinters. It seems also very troublesome and inconvenient to charge 12-in. cubes of sinter weighing about 100 lb into the testing drum. This could be eliminated by taking a standard fraction of somewhat smaller particles.

Jan 1, 1954

By W. H. Gunniss

When the copper smelters were built, in Montana, all of the refractory products which were used in their construction were shipped in from Eastern factories. It was apparent that if a material suitable for the manufacture of these products could be found within the State, a saving of freight could be effected and a new industry built up. Prospecting for such materials was started and experiments were made with samples from numerous deposits. Considerable effort and funds were expended in an attempt to manufacture silica brick from Dillon quartz, a light colored sandstone that is found near Dillon, Mont., on the Oregon Shortline railroad. As a brick material the Dillon quartz was a failure, but it has proved very satisfactory as a silica cement. It is now being used in laying silica brick and for reverberatory furnace bottoms. A bed of quartzite that is particularly suited to the manufacture of high-grade silica brick was finally discovered at Browns Spur, 6 miles west of Anaconda. The material from this deposit is now being used in the manufacture of the Anaconda silica brick, which have gained a wide reputation for heat-resisting and lasting qualities. The analysis of an average sample of this quartz is: SiO2, 96.7; Fe2O3, 0.3; Al208, 2.5; CaO, 0.3 per cent. The very low percentage of fluxing ingredients makes this a most refractory material. All of the Anaconda silica brick are hand molded. Various types of brick machines have been tried, but the hand-mold process proved the best suited to the manufacture of silica brick from this material. The silica is first put through a jaw crusher and is then dumped into wet pans, where 4 per cent. of lime paste is added, to produce a bond. Without the lime the material would not be plastic enough to mold. After a few minutes&apos; grinding in the wet pans the material is conveyed to the molder, who forces it into the molds by hand. The brick are then dumped on pallets and placed in the drier, where they are left. until dry enough to be set in the kilns. Some of the brick are re-pressed before being dried. They are burned about five days, in round down-draft kilns. It is not necessary to have as much heat in the kilns as the brick will be subjected to when in use in the furnaces. Montana refractories are used in smelters throughout the West. Prospecting for fire clays was also carried on. After experimenting with clays from several different deposits, it was found that a mixture of

Jan 1, 1914

By W. A. Dickinson, H. F. Hendershot

THIS paper is a brief discussion of the past and present methods employed by the Huntington Works of The International Nickel Co., Inc., in the production of nickel and high nickel alloy seamless tubing. The various operations for both hot and cold processing will be considered in their natural sequence, together with the processing characteristics of the high nickel alloys and some descriptions of the equipment used. The tools and lubricants currently in use will be described. This discussion will relate primarily to nickel, Monel,† and Inconel,† since these are the most common of the many alloys processed into tubing at the Huntington Works. The nominal compositions of the materials are shown in Table I. CONVERSION FROM SOLID BILLETS TO TUBE SHELLS History The commercial production of seamless nickel and high nickel alloy tube shells is a comparatively recent development, the first nickel shells having been produced in 1922, Monel in 1930, and Inconel in 1931 on rotary-type piercing mills. Rolled or forged billets, ranging from 3 ½ - to 7 ½ in. diam, were pierced to produce shells ranging&apos; in size from 4 3/8 in. OD X 0.180 in. wall to 8 3/8 in. OD X 1.0 in. wall. After piercing, the shells. were further processed by hot rolling, reeling, and sizing. Subsequent to these operations the shells were either supplied to the trade as "hot finished" tubes, or were processed by cold drawing to smaller sizes at the Huntington Works of the International Nickel Co. The extrusion of nickel and high nickel alloys also may be classed as a relative newcomer to the field of hot-forming methods, for it was not until 1928 that the commercial extrusion of these alloys was begun on a 600 long ton vertical extrusion press installed at Zenith Works of Henry Wiggin and Co., Ltd., Glasgow, Scotland. This press did considerable pioneer work and the results were so favorable that in 1937 a -2200 long ton horizontal press was installed. The quality of the inside surface of the tubing produced on this press was superior to that produced by piercing on a rotary-type mill and, as a result of this experience, a 4000 ton horizontal extrusion press was installed at the Huntington Works in 1943. Billet Preparation The first step in the extrusion, process is the selection of ingots with good hot malleability, as indicated by the test described by Martin and Bieber.1 Ingots then are forged into rough rounds which are machined to the desired billet diameter on a "bar peeler." This machine consists of a rotary head which carries the cutting tools and is driven by a 200 hp, dc motor. The feed mechanism consists of hydraulically driven input and output carriages on the respective sides of the cutter head. The diameter of the forgings used and the machined size or "billet diameter" that corresponds to the four different sizes of

Jan 1, 1951

By William L. Lennemann

Chemistry of uranium with respect to its hydrometallurgical recovery from carnotite ores was investigated and well defined during the radium boom period between 1900 and 1920. Since that time, methods used to extract uranium from its ores have remained basically either acid leaching or sodium carbonate leaching. Until about 1950, the only practical methods known for achieving a better than 75 pct U2O3 concentrate from the leach liquors involved fundamental chemical techniques for either purifying a solution prior to the uranium precipitation, or refining a crude uranium concentrate that was produced by neutralizing a pregnant mill liquor.

Jun 1, 1956

By E. D. Levine

A study was made to delineate the dislocation mechanistns controlling prismatic and basal slip at low temperatu.ves in titanium containing approximately 100 ppm interstitial impurities. Mechanical tests were performed on single crystals prepared from electron-beam zone-refined crystal bar by a thermal cycling technique. Measurements were made of critical shear stress and activation volume as functions of temperature. The study revealed that, for prismatic slip, two overlapping thermally activated processes aye rate-controlling below 300°K. From absolute zero to 220°K, reasonable agreement is obtained between experiment and the mechanism which involves overcoming 01. the Peierl&apos;s stress by the formation of double kinks in dislocation lines lying in close-packed directions. Between 220°and 300°K prismatic slip is controlled by a difierent thermally activated process which is characterized by a stronger temperature dependence of critical shear stress. Above 300OK, prismatic slip is controlled by an athermal process. Basal slip is controlled by a thermally activated process between 195&apos; and 400°K. An approximate analysis suggests that it is the Peierl&apos;s mechanism that is rate-controlling in this range. Below 195°K, the occurrence of mechanical twinning obscures the features of basal slip. Above &apos;400 X, basal slip is controlled by an athermal process. TITANIUM, an hcp metal with a less-than-ideal axial ratio of 1.587, deforms primarily by {1010}( 1210) slip at low temperatures.&apos;-3 The critical shear stress is strongly affected by the presence of interstitial impurities. For example, churchman3 reported that a decrease in the combined nitrogen plus oxygen content from 0.1 to 0.01 pct decreased the critical shear stress for prismatic slip from 9.19 to 1.4 kg per sq mm at room temperature. Basal slip, however, is less strongly affected by interstitials; Churchman&apos;s data for {0001}( 1210) slip show a smaller decrease in critical shear stress from 10.90 to 6.3 kg per sq mm at room temperature, for the same decrease in interstitial content. In the present study, an attempt has been made to delineate the dislocation mechanisms controlling prismatic and basal slip in titanium. In view of the strong effects that impurities may have on at least some of these mechanisms, experiments were performed on material of reasonably high purity, so that comparisons could be made with investigations on material of both lower and higher impurity contents. EXPERIMENTAL PROCEDURE Single crystals were prepared from 1/4-in.-diam electron-beam zone-refined crystal bar, furnished by Materials Research Corp. The analysis of the zone-refined material is given in Table I, indicating that the interstitial content is of the same order as the purer of the two materials investigated by Churchman. The Vickers diamond pyramid hardness number of this material was 85.6. This value agrees quite well with the correlation between hardness and interstitial content proposed by Ogden and Jaffee.4 On the basis of hardness, the material investigated in this study is, therefore, intermediate in purity between that studied by Churchman (Vpn = 97) and that studied by Spangler and Herman (Vpn = 62.4).5 Single crystals were grown by thermal cycling through the a-ß transformation. Two-in.-long by 1/2-in.-diam bars were heat-treated in vacuum for 4 hr at 1160°C. The temperature of the furnace was then lowered to 865°C, and the specimens were maintained at this temperature for 7 days. This procedure was repeated several times, resulting in the growth of individual crystals up to 14 in. in length. Specimens for testing in direct shear along either {l010}(1210) or {0001}(1210) were obtained by electrical-discharge machining. The specimens were in the form of cylinders 1/4 in. in diam by approximately 1/2 in. in length, with a reduced section 1/8 in. in diam and a in. in length. All specimens were electropol-ished subsequent to electrical-discharge machining. The ends of the test specimens were cemented in stainless-steel collars. Shear tests were conducted in an Instron Tensile Tester at various temperatures from 4.2° to 508°K. Measurements were made of critical shear stress and activation volume. The latter measurements were performed by measuring the change in flow stress upon cycling the strain rate between ?1 = 2.62 x 10-3 per sec and ?2 = 2.62 x 10-4 per sec. Activation volume, I)*, is defined as u* =ßkT [11

Jan 1, 1967