Search Documents

Commonwealth of Pennsylvania, Department of Internal Affairs, Topographic and Geologic Survey, Harrisburg, Pa George H. Ashley, State Geologist All available printed Bulletins may be obtained through the Commonwealth of Pennsylvania, Division of Documents. Where a price has been set on the publication, checks should be made out to the Commonwealth of Pennsylvania. A Syllabus of Pennsylvania Geology and Mineral Resources has recently been published by the Survey as Bulletin G1, and consists of a general survey of the state An appendix of this bulletin also gives a complete bibliography of Survey publications It will be sent upon request. The State Geological Survey has gone through several phases and reorganizations, publications of three of them being numerous and important A fire, in 1927, destroyed supplies of many of the papers of the present Survey. Available bulletins of the present Survey are: Bulletin M6: Bituminous coal fields of Pennsylvania, in 4 parts available as follows: pt 1, General description of coal, 50 cents; 3, Bituminous coal resources, 25 cents, 4, Analyses of bituminous coals, 25 cents Bulletin M10, Fire clays of Pennsylvania; Mll, Molding sands of Pennsylvania; M12, Anthracite culm and silt (1928); M13, Feldspar in Pennsylvania; M14, Magnetite deposits of French Creek (1931); County Report C1, Adams County, pt 1, Geology and geography (in press), County Report C2, Geology and mineral resources of Greene County (in press); Topographic and Geologic Atlas A5, New Castle Quadrangle (1929), $1; Topographic and Geologic Atlas A27, Pittsburgh Quadrangle (1929), $1; Topographic and Geologic Atlas A168, Lancaster Quadrangle (1930), $1. The present Survey has also issued a number of short mimeo¬graphed bulletins any of which will be sent upon request Briefly they are: No. 15, Mineral resources of Pennsylvania; 20, Iron ores; 28, Magnesite; 40, White clay deposits, Monroe County; 45, White clay deposits, central Pennsylvania; 47, Manganese, Eastern Pennsylvania, 48, Pyrite from bituminous coal mines; 59, Bog

Jan 1, 1933

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By W. T. lsbell

HERCULANEUM, MO., about thirty miles south of St. Louis on the Mississippi River, is the site of the lead smelter of the St. Joseph Lead Co. The lead concentrates come by rail from the Flat River district and from three properties in Madison County, Missouri; from the Balmat division in St. Lawrence County, New York; a small tonnage from the Tri-State district; and occasionally from the Aguilar property in Argentina. The average grade is 67 to 68 percent lead and 1 to 3 oz of silver. The bulk of the material is flotation concentrate, with some gravity or table concentrate. No secondary metals, outside drosses, or any materials high in bismuth, arsenic, or antimony are treated. All concentrate is received in box-caps and is unloaded directly from a trestle into the concentrate bins at the roaster plant. Flux, coke, and any miscellaneous lead-bearing material is either unloaded directly into bins or unloaded with a locomotive crane. All moving and switching of cars is done with two thirty-ton steam locomotives. Shipping facilities for the plant are provided by the Missouri-Illinois Railroad. Water for the plant and for fire protection is obtained from a dam built in a near-by creek. Drinking water both for plant and town is obtained from

Jan 1, 1947

By F. S. Pettit

The oxidation of Ni-3 to 25 wt pd Al alloys has been studied in 0. 1 atm of oxygen at temperatures between 900° and 1300°C. These alloys have been found to oxidize by three different mechanisms which depend on the temperature of- oxidation and the alloy composition. Two of the three mechanisms do not permit a continuous layer of Al,0, to be formed on the alloy surface and the oxidation rates are greater than that for pure nickel. The third mechanism results in the formation of an external A1203 scale and lke oxidation rates are about three orders of magnitude smaller than those for pure nickel. The minimum amount of aluminum required for the formation of external scales of A L,0, has been determined. NICKEL-base alloys are currently the main source of materials for use at elevated temperatures in gas turbine engines. These alloys are usually coated to obtain oxidation resistance. Coatings on nickel-base alloys are frequently formed by reaction of the alloy with aluminum whereby alloyed nickel aluminides are formed. The alloyed nickel aluminides provide protection to the nickel base alloy because external scales of A1203 (alumina) are formed during oxidation and mass transport through A120, is slow in comparison to mass transport through most other oxides. In view of the protective properties of A1203, it is important to know how much aluminum is required in these alloys in order to form external scales of AlzO,. The present paper is concerned with the oxidation kinetics and the oxidation mechanisms of Ni-A1 alloys and the minimum amount of aluminum required in these alloys for the formation of external scales of Alz03. THEORETICAL CONSIDERATIONS When a Ni-A1 alloy is heated in oxygen at elevated temperatures, the following reactions can take place on the surface of the alloy where the oxide phases are assumed to be virtually pure: These oxide phases are in the form of nuclei scattered over the surface of the alloy and, in view of their rapid formation, they need not be in equilibrium with the alloy. As the oxidation process continues, equilibrium between the alloy surface and the oxide phases is approached and the stability of the oxide nuclei is determined by the composition of the alloy at the alloy/oxide interface because of the following reactions: 3NiA1204 + 2A1 (alloy) = 4AlzO3 + 3Ni (alloy) [41 4Ni0 + 2Al (alloy) = NiA120, + 3Ni (alloy) [ 5 1 Application of the mass-action law to Eqs. [4J and [5J yields the following equilibrium conditions for these reactions: where aA1 and aNi are the activities of aluminum and nickel, are the standard free energies of formation of NiO, A1203, and NA1204, respectively, R is the gas constant, and T is the absolute temperature. If the composition of the alloy at the alloy/oxide interface is such that (akl/ahi) is greater than the equilibrium values defined by Eqs. [6] and [7], then Reactions (41 and [5] will go to the right as written. Conversely, if the alloy composition is such that the activity ratio (aLl,/aki) at the alloy/oxide interface is less than the equilibrium values, then Reactions [4] and [5] will proceed to the left. The equilibrium activity ratios in Eqs. [6] and 171 can be calculated since values for the standard free energies of formation of the oxide phases are available. Standard free energies of formation for NiO and A1203 have been tabulated by Elliott and ~leiser.&apos; The standard free energy of formation for NiA1204 can be obtained from the data of Tretjakow and Schmalzried.&apos; The results of these calculations are tabulated in Table I. Table I shows that the following inequality is valid over the temperature interval 900" to 1300°C: (Reaction [5]) (Reaction [4]) « 1and therefore the aluminum activity for these compositions can be taken as equal to the square root of the activity ratios (i.e., aNi = 1). If equilibrium is estab-

Jan 1, 1968

By Scott Howard

MANGANESE being perhaps the least expensive of the metallic alloying elements that can be advantageously added to iron in considerable quantities, the basic characteristics of its alloys with iron are properly receiving much attention at present. In the course of a dilatometric investigation of this system several years ago, the writer observed certain transformation phenomena not found in other iron-base alloys. The interpretation of those effects was not evident from the information then available, but recent X-ray studies clear up at least one anomaly and permit a more satisfactory description of the results than would have been possible otherwise. Aside from the new phenomena observed, the effect of manganese on the Ar3 transformation is of timely interest because of its bearing on the critical compositions of austenitic alloys, the applications of which are now being greatly extended. It is known that the properties of these alloys are unstable unless the Ar3 transformation occurs at a temperature considerably below atmospheric and that manganese is very effective in depressing the temperature of this transformation. The writer aims to establish a simple general relation which expresses the location of Ar3 quantitatively in terms of the content of the common alloying elements used in steel. A step in that direction is taken here. Early dilatometric investigations1 indicated that only one transformation other than the eutectoid A1 occurs in the high-iron alloys of the iron-manganese system. Dejean represents the Ar3 point as falling to 0° C. with a manganese content of 11 per cent and carbon content of between 0.30 and 0.40 per cent. Esser and Oberhoffer,2 using alloys low in carbon (under 0.03 per cent), arrived by extrapolation at 14 percent for the manganese content at which Ar3 is depressed to 0° C. Not until both low carbon contents and alloys having a manganese content

Jan 1, 1931

By E. T. Turkdogan, J. H. Swisher

The solubility of oxygen in zone-refined iron was determined in the temperature range.from 881" to 1350°C. The solubility in a iron at 881°C ms found to be about 2 to 3 ppm; in y iron, the solubility was found to increase from about 2 to 3 ppm at 950°C to about 25 ppm at 1350°C. The permeability of oxygen in an iron -0.1 pct Al alloy was determined in the y iron range, using an internal oxidation technique. By combining the permeability and solubility data, the diffzisivity of oxygen in y and a iron was calculated. The oxygen diffusivity in solid iron may be s~immarized as follows: 8820 For 6 iron and IN a recent paper, Hepworth, Smith, and Turkdogan1 reported on the solubility, permeability, and diffusivity of oxygen in 6 iron, together with permeability data for oxygen in a iron. In the present investigation, similar measurements were made in the ? phase region. In addition, a solubility measurement was performed in the a phase region to permit calculation of the diffusivity of oxygen in a, iron. References to early work on this subject are given in the previous publication.&apos; EXPERIMENTAL Solubility Measurements. The oxygen solubility was determined by equilibrating cylindrical samples 0.3 in. diam by 14 in. long of zone-refined iron in water vapor-hydrogen gas mixtures. The zone-refined iron was prepared by B. F. Oliver of this laboratory, using an apparatus and technique described elsewhere.2&apos;3 Six zone-melting passes were used to achieve a total impurity level of about 30 ppm. Of this 30 ppm, the combined nickel and cobalt content was about 20 ppm, oxygen was 4 ppm, and all oxidizable impurities less than 1 pprn each. A vertical resistance furnace wound with molybdenum wire was used for the experiments. The temperature was measured before and after each experiment with a Pt/Pt-10 pct Rh thermocouple. In the gas train, flow rates of hydrogen and argon were measured with capillary flow meters, and the resulting mixtures were passed through a column containing 90 pct oxalic acid dihydrate and 10 pct anhydrous oxalic acid to obtain predetermined ratios of H2O to H2. The vapor pressure of H2O above this mixture as a function of temperature is well-known.4 The exit gas was ana- lyzed periodically for H2O, and good agreement (+3 pct) with the calculated composition was obtained. The zone-refined iron specimens were held in the furnace for a sufficient length of time for equilibration, e.g., 18 hr at 1350°C and 1 week at 881°C, then quenched in a brine solution. After removing the surface oxide from the samples by machining, duplicate analyses were obtained by a combined vacuum fusion-infrared method; oxygen analysis was reproducible within 2 ppm. Permeability Measurements. The permeability of oxygen in alloys containing about 0.1 pct A1 was determined by internal oxidation and measurement of the subscale thickness as a function of time. The experimental alloys were prepared by adding aluminum to electrolytic iron (grade 104A plastiron) that had previously been vacuum-carbon deoxidized. The resulting ingots contained about 20 ppm O, 100 pprn C, 40 pprn Si, 50 ppm Mo, 20 ppm P, 20 ppm S, and 20 pprn Zr as the principal impurities. After hot rolling the ingots to 1-in.-thick slabs, specimens were machined from the stock in the form of rectangular plates, 4 by 5 by 2 in. The general procedure for the permeability experiments was the same as those for the solubility measurements. The specimens were cooled in a reducing atmosphere rather than quenched, however, in order to maintain a clean surface for measurement of the sub-scale thickness. This measurement was made on a polished cross section of each specimen, using a microscope with a micrometer stage. The inclusions formed at the lowest temperature 1033°C were too small to be seen with an optical microscope. An electron micrograph showing the size and shape of individual particles is shown in Fig. 1. The dark band in the picture is a boundary between two subgrains. The subscale thickness in these samples was measured with an optical microscope after heavily etching in 2 pct nital, which gave contrast between the subscale and the unoxidized zone.

Jan 1, 1968

By Roy C. Kirkman

Dear Editor: It is with great pleasure that I read Mr. Howard M. Wells article in the December 1978 issue of MINING ENGINEERING entitled: "Optimization of Mining Engineering Design in Mineral Valuation." Mr. Wells very adequately presents the case and point that there are a great number of variables which must be analyzed during an economic evaluation of an FUND RESOURCE, such as copper or uranium. I wish to take this opportunity to suggest that, given today&apos;s economic climate, decision making takes place under conditions of uncertainty and that this uncertainty justifies our need to examine each one of the parameters entered into the evaluation model. It is my contention that the influence of the tonnages and grades as well as their distributions, have the most profound effect upon the results of an evaluation. Everyone concerned with the evaluation of FUND RESOURCES realizes that as metal prices decline or stagnate with sharply rising direct operating costs, cutoff grades (Gc) must increase according to the equation below which Mr. Wells uses: Gc = Total Operating Cost/(Market Price X 20 X Recovery) However, historically, we have seen cutoffs move dramatically lower in both the copper and uranium industries for the past decade. Henceforth, this established the metals industry most important argument for processing greater tonnages of lower grade materials from disseminated deposits (refer to paper by Kirkman, Roy C.). These disseminated deposits, created by either concentration processes (uranium) or dispersion processes (copper, gold, molybdenum), have log-normal grade distributions (Fig 1). Gross profits are rising, but unit profits are falling. The industry has created longevity through economy of scale, i.e., mining vast tonnages of low grade. In order to develop the great tonnages necessary to prove economic viability, we must examine alternatives at the low-end of the tonnage grade relationship. Notice from [Fig. 2] that as we move further to the right away from line A-B drawn tangential to the average grade curve at 45°, total profits will increase (given fixed annual production capacity) and unit profits decrease. The theoretical optimum operating point is where: [ ] At this point my observation is that slight shifts in production capacity bring about greater changes in profitability due to greater grade changes. Therefore, the best financial risk evaluation is obtained by totally revising the mining engineers methods and fixing the financial parameters such as discount and interest rates. A 10% shift in either of these two parameters will not cause near the same variance in economic viability as will a change on the GRADE-TONNAGE curve [(Fig. 2)].

Jan 1, 1980

By F. C. Canney

Geochemical prospecting seeks hidden mineral deposits by sampling for variations in the chemical composition of naturally occurring materials. Usually the samples are of soils and other products of weathering and erosion-surface materials extremely susceptible to contamination by human activities. Except when a survey is conducted well away from populated areas, contamination is an ever-present hazard. The program&apos;s success is particularly endangered when the contaminants are the elements sought; if these occur erratically throughout an area, spurious anomalies completely unrelated to mineralized areas can be formed. Evenly distributed contamination can be dangerous too, if it raises the background to such a level that true anomalies can no longer be easily detected. Suppose, for ex- ample, that in an area where the lead background is 20 parts per million the soil over a lead vein contains 1000 ppm of lead. Here the contrast would be 50 to 1, which is very satisfactory for geochemical surveying. Now if 1000 ppm of lead from some source were added evenly to the soil in this area, the contrast would be reduced to about 2 to 1, and the anomaly would no longer be readily detectable because a threshold of significance twice the value of the background is the minimum generally used for interpreting geochemical data.

Jan 2, 1959

By Paul D. Merica

DURING the Dark Ages, when metallurgy was practiced by the alchemists, any unusual or disturbing variation in metallurgical operations was ascribed to the, presence, in the metals or ores, of an evil spirit, and it was necessary to exorcise and drive it out "by suitable incantations. In this day of science and of engineering, things still incomprehensibly go wrong in the metallurgist&apos;s work shop. The metallurgist is even now not unwilling to lay the blame for many such experiences at the door of something which intellectually- much resembles an evil spirit, "gas in the metal." The presence of gases in his metal, he knows, occasions him many very definite troubles which he can clearly distinguish and diagnose-why may it not be also responsible for those which he cannot so well understand?

Jan 1, 1931

By Donald M. Liddell

From a commercial standpoint, the only beryllium mineral warranting attention is beryl, 3Be.Al2O3.6SiO2, which is of fairly widespread occurrence. The chief deposits are in Brazil, Argentina, India, Canada and Portugal. When pure this contains about 14 per cent of beryllium oxide. The mineral richest in beryllium is phenacite, (BeO)2SiO2, or beryllium orth-osilicate, which contains 45.55 per cent beryllium oxide when pure, and if anyone is ever fortunate enough to discover a large deposit of it, it will revolutionize beryllium metallurgy. Gadoljnite, zBe0.Fe0.2Yz0~.zSi0~, is also often referred to as a beryllium mineral, though the occurrences are comparatively scant and it is of more interest as a source of yttrium than it is of beryllium. There has been a good deal of talk recently regarding some occurrences of helvite in the United States. Helvite is a complex manganese-iron beryllium silicate and, apart from difficulties that would arise in its treatment because of its compo-sition, the beryllium content of the known deposits is not high. Early Metallurgy The elemcnt beryllium was first isolated by L. N. Vauquelin in 1797.~ He crushed and heated beryl, having the idea that this heating made it more readily amenable to attack by chemicals, and then mixed the mineral with three times its weight of caustic potash and fused the mixture. The melt after cooling was dissolved in hydrochloric acid: dehydrated, and again taken up with hydrochloric acid and filtered to separate the silica. The filtrate was treated with an excess of potassium carbonate and the precipitate after draining was leached with a solution of caustic potash, which dissolved the alumina. The undissolved material was, in Vauquelin&apos;s own words, "une terre nouvelle." He dissolved the precipitate with nitric acid and evaporated it to dryness, took up with hydrochloric acid and threw the iron out with potassium hydrosulphide, though he found that to make a complete separation of the iron involved a second treatment. The solution, after throwing out of the iron, had a pronounced sweet taste, and though Vauquelin always speaks of working on "terre du beril" he suggests that the new element should be known as "glucine" (glucinum) from the Greek word for sweet, because of this outstanding property. Vauquelin did considerable work on the comparison of aluminum and beryllium, working out a separation of most of the aluminum based on its precipitation as alum. His work is reviewed at some length, since ordinarily his procedure is incorrectly stated. It will also be recognized by those who have studied beryllium metallurgy that a good many technicians have followed his ideas since, including preheating the beryl before treatment. The fusion with

Jan 1, 1944

By A. L. Mular

The flotability of crushed zinc oxide pellets which were doped to produce more n-type or less n-type (more p-type) properties was studied with a Halli-mond tube. Flotation data are presented to show that the pH at which 50% recovery occurs and the collector concentration for 50% recovery depends upon the concentration of doping agent added substitu-tionally for zinc in zinc oxide. The time of sintering of pellets has a slight effect on flotation behavior. A speculative model is proposed to explain the observed behavior in light of the fact that zinc oxide is a semiconductor and has a space charge region at the surface. Experimental verification is necessary before the proposed model can be established as correct. In recent years, the attachment of flotation reagents to minerals has been shown to depend upon the behavior of an electrical double layer which exists in the liquid near the mineral-liquid interface.&apos; Thus, a mineral placed in water will undergo a surface re-arrangement, most likely be preferential dissociation of lattice atoms or by surface adsorp-tion-desorption reactions, to form a dissociation electrical double layer with the solution. Among the many factors which influence adsorption processes, the past history of the mineral itself is one of the most important. Because of trace impurities, minerals from different localities may exhibit marked differences in flotation behavior. This is not unexpected, since investigators who have studied the detailed structure of the double layer&apos;s3 have known for some time that the impurity content of many minerals may exert strong influence on double layer variables. For this reason, their studies were usually made with minerals of high purity. The precise relationship between impurities in a mineral and double layer parameters such as capacity and electrostatic potential has been obscure. However, impurities in a semiconductor type mineral which is in contact with a solution have been recently shown to produce changes in the properties of a space charge layer which extends into the bulk of the semiconductor to a distance of one micron or more.4 The double layer is influenced by the space charge layer, whose origin is best discussed in terms of the band theory of solids. A qualitative description of the behavior of impurities in the bulk of a semiconductor, from a chemical point of view, is useful at this point. Briefly, impurities or defects (lattice vacancies, interstitials, etc.) in semiconductors such as PbS, ZnS, FeS2, Cu2S, NiS, NiO, Fe2O3, ZnO, CdS, MnO2 and many others, behave somewhat like acids or bases in water. For example, water dissociates into hydrogen and hydroxyl ions according to

Jan 1, 1965

By H. M. Dess, S. R. Bolin

A modifiedl Czochralski technique has been utilized to grow single crystals of YVO, pure or doped with europium or neodymium, from 1 to 2 in. long and 4 to 1/2 in. in dianz. An oxyhydrog-en gas-fired furftace zuas used in this ulork, and melts were contained in iridium crucibles. Successful application of the Czochralski ~vzethod was found to depend upon atmosphere control to prevent crusting and to limit melt decomposition, the establishment of symmetrical thermal gradients in the melt to obtain stable growth, and the selection of high-quality single-crystal seeds to prevent propagation of misorientations during growth and subsequent catastrophic cracking. The suitability of YVO4 as a host for laser-active trivalent rare earth ions has long been recognized. However, the problems associated with the growth of sufficiently large, good-quality single crystals have, until quite recently, seriously hindered satisfactory evaluation of the laser potentialities of this material. Both flux growth and Czochralski growth techniques were investigated at an early stage of interest in YVO,. The former method proved incapable of yielding crystals large enough for practical use,ly2 and the latter was beset with difficulties which took some considerable time to understand and overcome. Recently, however, the Czochralski growth process for YVO, has been improved along separate but similar lines of development by groups working independently in the Crystal Products Department of Union Carbide&apos;s Electronics Division and Bell Telephone Laboratories3 so that now good-quality single crystals of satisfactory size can be produced on a routine basis. Stimulated emission from a neodymium-doped YVO4 crystal grown by the Crystal Products Department of Union Carbide was obtained by O&apos;connor4 of MIT, Lincoln Labs. An oxyhydrogen gas-fired furnace was used in this work, Fig. 1, and melts were contained in iridium crucibles. The starting material was 99.9 to 99.99 pct pure YVO4 powder purchased from the Chemical and Metallurgical Division of the Sylvania Electric Products Co. Typical impurity levels, determined by spectrographic analyses, were as follows: Si, 50 to 500 ppm Al, Fe, Mg, 5 to 50 ppm Ni, Pb, Mo, Mn, Ce, Cs, 1 to 10 ppm Initially, YV04 powders predoped with neodymium or europium were obtained from Sylvania. Later, however, because of a desire to grow a series of crystals containing relatively broad concentration ranges of these dopants, it proved more convenient to start with pure YV04 and mechanically admix Nd2O3 or Eu@~ powders plus equimolar amounts of V2O5. The empty crucibles were preheated to 1900" to 1950oC, a temperature range where melting occurred readily. The powdered YVO4 feedstock was then added incrementally. However, a marked tendency toward

Jan 1, 1968

Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. &apos;35 Allen, Carl A., Student, Colorado School of Mines Golden, Colo. &apos;35 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. &apos;35 Allen, R. M., Jr., Student, Virginia Polytechnic Inst., "G" Co Blacasburg, Va. &apos;35 Amberger, K. H., Student, Michigan College of Min. & Tech Houghton, Mich. &apos;35 Andersen, Burton Lee, Student, School of Mines, Univ. of Washington Seattle, Wash. &apos;35 Anderson, Joseph S., Student, Univ. of Texas El Paso, Tex. &apos;35 Anderson, R. C., Student, Univ. of Washington Seattle, Wash. &apos;35 Ansel, Gerhard 627 Clyde St., Pittsburgh, Pa. &apos;34 Anutta, Frederick P., Student, Michigan College of Min. & Tech Houghton, Mich. &apos;35 Apsouri, Constantin N., Graduate Student, Univ. of Arizona Tucson, Ariz. &apos;35 Arakelian, Haig Mark, Student, Mass. Inst. of Tech Cambridge, Mass. &apos;34 Archer, George K 1420 Court Pl., Denver, Colo. &apos;34 Argall, George O., Jr., K. E. House Golden, Colo. &apos;35 Argiielles, Alfredo, Student, Univ. of Texas El Paso, Tex. &apos;35 Atwater, Ralph, Student, South Dakota School of Mines Rapid City, S. D. &apos;35 Austin, Robert B., Miner, Page Mine, Federal Min. & Smelt. CoSpokane, Wash. &apos;34

Jan 1, 1934

By L. L. Davis

The rapid increase in the use of pulvcrulent adsorptive materials in the so-called "contact filtration" process for decolorizing lubricating oils makes it desirable to consider some of the basic principles involved. The commercial methods and types of equipment now used arc fairly well known, having been extensively described in the trade journals. In spite of this very little has been published concerning the factors which must be considered in the selection of a process or of a decolorizing ing material. It is commonly understood that contact filtration more or less closely follows the laws of adsorption. These principles have been thoroughly drscribed by Gurwitsch.&apos; The contacting of neutral mineral oils seems to be adsorptive in character and apparently follows Freundlich&apos;s law of adsorption which may be expressed by the formula: X = Color material adsorbed hy the clay. M = Amount of clay used. C = Concentration of color material after equilibrium. A and P = Constants for a given oil and clay. Fig. 1 shows the decolorization curve for a natural, dark colored cylin-der stock when contacted with various quantities of clay, curve R being made with natural Riverside Texas fuller&apos;s earth and T being made with an acid-treated clay from Texas. As the Tag-Robinson color is inversely proportional to the depth of color, the reciprocal of these colors ran be assumed to be a funct ion of the concentratlion of coloring matter. The values of and C&apos; can, therefore., br calculated by using the reciprocal Tag-Robinson colors, and when these

Jan 1, 1928

OF the many categories into which scientific knowledge has been arbitrarily divided, the one that has proved most applicable in our attempts to gain an insight into the details of steelmaking processes is physical chemistry. To the young metallurgist who has only recently survived a college course in this subject, the application of its principles to reactions in liquid steel should not be difficult. The many excellent textbooks of physical chemistry1 provide ample material on the principles of this subject for the student of steelmaking processes; yet with- out exception those texts draw the greater part of their illustrative material from room-temperature data. It is the purpose of this chapter to provide a concise review of the principles of physical chemistry that have proved useful in studies of steelmaking and at the same time to present some of the data that are essential to the application of physical chemistry to reactions at high temperatures. Certain parts of physical chemistry require rather formidable mathematics for their complete development but in the main those applications in which we are here interested can be ex- pressed in fairly simple terms. Many of the equations are logarithmic, and we shall use the symbols In X and log X to represent respectively the natural and the common logarithm of X. The two are related by In X = 2.303 log X. Logarithms may be read from a good slide rule with sufficient accuracy for our purposes. In a few spots a knowledge of the calculus will be, helpfu1. MATTER Innumerable forms of matter may be recognized, and these may be converted by chemical processes into others, as ore, coke, and air are converted into iron, slag, and gas. Whenever such a change occurs there is a corresponding change in

Jan 1, 1951

By Emile Gyss

THE speed of drilling rock has become an impor-tant factor in mining operations, while the place-ment of holes, kind, and quantity of explosive used. are equally important. These are a function of the rock hardness and toughness. Both of these fac-tors must be considered in compiling a table that will enable a mine operator or engineer to estimate drilling speeds in a given rock, knowing its hardness, and from its toughness, the dynamite required. The hardness of a homogeneous rock may be defined as its resistance to a penetrating medium, such as a drill-steel bit, and toughness, its resistance to with-stand rupture by the tearing apart of its minerals or parts of the same mineral. Rock hardness, as it has here been defined, is a function of the hardness of the component grains composing it, as well as grain size, shape, arrangement, and binding minerals. Rock tough-ness depends on substantially the same factors, but is measured by a totally different method. The units in which rock hardness is usually ex-pressed are either relative values or alphabetical desig-nations which carry no definite quantitative meaning. R. M. Raymond has suggested the measurement of com-posite rock hardness, based on mineral hardness as ob-tained by the Moh scale. This is done by multiplying the percentage of each mineral in a rock by the Moh mineral hardness and dividing by 100. These values convey a clearer conception in the minds of men in-terested in rock work -and are the basis of the units used in Tables 1 and 2. The hardness of rocks as it has been variously de-fined may be determined by different methods. The first method is one in which the proportionate average of the hardness of minerals making up a rock is the basis for classification. The other factors of grain size, shape, arrangement, and binding power are not considered.

Jan 6, 1927

By THOMAS G. FEAR

THE COAL DIVISION started its share of the annual meeting Monday morning with a study of coal classi fication. A. C. Fieldner was in the chair. The report of the tellers of the ballot for division chairman, stating that Thomas G. Fear had been elected to that office, was read by M. D. Cooper. Mr. Fear acknowledged the honor in a few words. In reviewing the history of the Coal Classification Committee the chairman pointed out that this was its third symposium, the last previous one having been held at the 1930 Annual Meeting. Throughout its work the com¬mittee has had the active cooperation of the Canadian workers who are interested in the subject which should result in a uniform scheme of classification in Canada and the United States. F. E. Lathe, of the National Research Council, Ottawa, abstracted the first two papers of the session entitled "Determination of the Alkali-Soluble Ulmins in Coal," by Edgar Stansfield and K. C. Gilbart, and "Moisture Determination for Coal Classification," by the same authors. The third paper "Condition of Water in Coals of Various Ranks"&apos; was presented by its author, A. W. Gauger. Written discussions of these papers were presented by H. C. Porter and Gilbert H. Cady. In the oral discussion which followed, W. T. Thom, Jr., brought out the advisability of considering age as a factor in classification. Mr. Fieldner favored retaining bed moisture as a partial classification basis, stating that a review of many coal analyses revealed a remarkable consistency in this item in samples from a given mine particularly where the moisture content was not high. Mr. Porter pointed out that the structure and porosity of coal often have much to do with its moisture content and that these vary in different parts of a seam, particularly in anthracite. Mr. Gauger expressed doubt as to whether the Stansfield method gives the true moisture content of coal, which is needed for classification purposes.

Jan 1, 1932

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By Thomas T., Read

IT will be recalled that the first professor of metallurgy in the United States, appointed in 1855, never really gave any instruction in metallurgy and gradually turned into a professor of mineralogy. Metallurgy was included with. mining in the early curricula, two students who took the B.S. in mining engineering from the Polytechnic College of Pennsylvania in 1862 wrote their graduation theses on the metallurgy of copper and zinc, respectively. Even after Columbia School of Mines established, in 1868, a separate curriculum leading to the Ph.B. degree in metallurgy, very few students elected it,* preferring to take the mining degree, since they received in its curriculum nearly all the metallurgical instruction they would have in the metallurgical curriculum. For many years a large proportion of the men who attained prominence in metallurgical enterprises had taken mining rather than metallurgical degrees. METALLURGY Clifton Sorby&apos;s study of thin sections of rocks under the micro¬scope, beginning in 1850, and its subsequent development by Zirkel and others, had made microscopic petrography a recog¬nized department of geological research as early as 1873. . It was inevitable that the idea of studying polished metal surfaces-¬under the microscope by reflected instead of transmitted light would occur to investigators. Sorby himself did it in 1864, and Adolph Martens and Floris Osmond may -be especially named among the many European workers who, by the late eighties, had so developed the, necessary techniques that they were able to photograph polished metal surfaces at magnifications as high

Jan 1, 1941

By CHARLES HOPPER

In preparing the Steep Rock Lake iron ore body for mining, it was necessary to drain Steep Rock Lake. Using diamond drills, a cut 1800 ft long, 100 ft wide, and maximum depth of 95 ft amounting to 300,000 cu yd of material, was excavated in Greenstone to provide a drainage channel. This was done under the general contractor C. A. Pitts, of Toronto, who in turn employed a diamond drill contractor, Boyles Bros., to do the drilling. The method of excavation was selected be- cause a clean square cut and grade could be maintained in the bottom of the channel. Bootlegged holes would have left blocks of rock in the corners which would have created a situation which would have become progressively worse as the open cut advanced from one side of the ridge to the other.

Jan 1, 1949