Search Documents

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By AIME AIME

THE petroleum engineers have the conference habit. They drop in, thresh things over, and drop out. No time is wasted. So it was at the Fort Worth meeting of the Petroleum Division, Thursday and Friday, Oct. 8 and 9; headquarters, Blackstone Hotel. Associate Chairman Albertson arrived the morning of the 7th, to tie in any loose ends of the technical program. S. M. Greenidge, chairman of the local committee, checked the arrangements with his committeemen at a luncheon that noon. By mid-afternoon the next day's attendance was anybody's guess-there were no noses to count. But when the gavel sounded Thursday morning 175 members and guests were present, also the official A.I.M.E. party consisting of President Lovejoy, Secretary Parsons, and George Otis Smith. Shortly after adjournment Friday afternoon all but a handful had vamoosed, lit out, disap¬peared. But, in the meantime, it was a grand conference, attendance maximum every session, and the discussion fast and furious. The discussion came from all over the floor, sometimes as good-natured sniping, sometimes in long volleys that were almost fatal to the reporter. Everyone knew his subject and few there were who had nothing to say.

Jan 1, 1936

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,' or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By Carl Wagner

This paper contains solutions of the differential equation of diffusion in binary alloys if the diffusion coefficient is an exponential function of the concentration of one of the components. THE general differential equation for one-dimensional diffusion in a binary system can be written as: where c is the concentration of one of the two components in any suitable units; x, the distance from a reference plane; t, time; and D, the diffusion coefficient. Hartley and Crank&apos; have pointed out that eq 1 with conventional length units for measuring the distance x holds only if the alloy can be regarded as a rigid framework. In general, this is not the case, especially if the lattice parameter varies appreciably with composition. If a modified coordinate system is used instead of an orthodox system based on the centimeter a:: length unit, eq 52 is obtained, which has the same general form as eq 1 and is generally valid. The necessary transformations are presented in the appendix. If&apos; D is independent of concentration, analytical solutions of eq 1 are known for numerous boundary conditions. If D depends on concentration, solutions based on known analytical functions are not available. Among others, Boltzmann2 and Matano3 have shown that the concentration c depends only on (x/t1/2) in the case of diffusion between two semi- infinite spaces with uniform initial concentrations: c = c, for x < 0, t = 0, i.e., x/tl/2 = — x [21] c = c2 for x > 0, t = 0, i.e., x/tl/2 = + a Moreover, Boltzmann and Matano have shown how D may be calculated as a function of concentration over the whole range of composition from c -c, to c = c2 if c as a function of (x/t1/2) for the initial conditions stated in eq 2 has been determined experimentally. Thus, for instance, in principle, the diffusion coefficient in silver-gold alloys may be calculated as a function of concentration for the whole range of composition from only one diffusion experiment with a couple of pure silver and pure gold welded together. If the diffusion coefficient D as a function of concentration c is known, a solution of eq 1 for boundary conditions as stated in eq 2 with arbitrarily chosen values of c, and C2 may be wanted. For instance, if the diffusion coefficient in an alloy A-B as a function of concentration has been derived from an experiment with a diffusion couple involving 0 and 30 pct B as initial. concentrations, the calculation of the concentration distribution in a diffusion couple involving other initial concentrations, e.g., 5 and 20 pct B, may be desired. This problem may be solved by numerical or graphical integration of eq l. The solution of an ordinary differential equation of second order, which results from using (x/t1/2) as an independent variable, can be computed quite rapidly if two conditions for the same value of the independent variable are given. In eq 2, however, two conditions are given for two

Jan 1, 1953

By Fredrick C. Kruger

Introduction This surprisingly little-known group of minerals, the nonmetallics, so-called for their lack of metallic luster, is the largest group of the mineral kingdom, and cinstitutes perhaps 75 percent of all mineral species. For the most part, these minerals are compounds of the common acids, oxides, hydroxides, and two elements, carbon and sulfur. The list of the non- metallic minerals, therefore, is very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulfates, and less commonly, arsenates, chromates, molybdates, suliides, tungstates, and vanadates, the latter groups, and many of the oxides, being sought principally for their metal content. Those nonmetallics used commercially are generally called the industrial minerals, although in addition this term also includes a considerable group of rocks. The list of industrial minerals and rocks is continually growing as new uses are found, and it now numbers over 300 commodities. The industrial minerals industry has developed since about 1920. There- fore, the development has been fast, and it has been more or less parallel with the development of the art of minerals beneficiation. General Discussion of the Group This group is so heterogeneous that it has defied logical, or widely accepted, classification, whether by origin, composition, or end use, and perhaps for this reason the industrial minerals generally have received short shrift in both teaching and research. Except for those involved with asbestos, cement, fertilizers, gypsum, salt, sand and gravel, few large companies have deigned to enter the field, and consequently most industrial minerals have been developed for the most part by the small operators or entrepreneurs. Yet surprisingly, except for one war year, the nonmetallics have always surpassed the metals in value and tonnage (Fig. 1). One main characteristic that most of the nonmetallics have in common is direct sensitivity to labor and transportation. In other words they are characterized by large bulk and low-unit value, and hence have what might be termed a "place value".

Jan 1, 1971

By Carl M. Fellman

LABOR disputes caused considerable turbulence in the coal mining industry during 1946. As an outcome of these disputes, a definitely fundamental change in safety procedure was instituted: establishment of safety regultions for coal mines through the agency of agreements between the miners&apos; union and the agency or agencies operating the coal mines. Although a temporary plan at present, the future will determine the. extent to which it may become permanent. Notwithstanding the turmoil in the industry extending through much of the year, the safety record for the first eleven months of 1946 was the best in the history of the industry for that period. The fatality rate for 1946 is lower than in any other year in the history of coal mining in the United States. This follows a pattern inasmuch as new low coal-mine fatality records were also made in 1945, 1944, and 1943. The five-year period 1942 to 1946 inclusive has a coal-mining fatality rate far lower than any other five-year period in the history of the industry. It is significant that this period exactly coincides with the operation of Federal coal mine inspection which got under way early in 1942.

Jan 1, 1947

The following advertisements show the contemporary view of the value of coal on a tract, usually as compared with farming advantages of several kinds. Fayette Gazette and Union Advertiser, February 10, 1798: "For Sale in Washington twp., Fayette Co., 211 acres of land whereon is a good new grist merchant mill, a good stone dam, and a house for the miller, about two acres of bottom, cleared and fenced, an excellent coal bank and saw-mill seat unimproved." Pittsburgh Gazette, March 19 and 26, 1802: Ads. offering for sale two properties, one of 38 acres, "together with a Coal Pitt and Lime Quarry, lying on the Monongahela side of Grant&apos;s Hill, and within one mile and a half of Pittsburgh," and the other two tracts of 700 acres on "Racoon creek, contiguous to which is a valuable limestone quarry, and a quarry of building stone, also plenty of stone coal." Pittsburgh Gazette, Oct. 8, 1802: A farm between Pittsburgh and Greensburg "with house, barn and a Smith shop-also, a fine sugar camp, and a Coal Bank within sight of the house," was offered for sale. The Farmers Register, Greensburg, Pa., March 13, 1802: An advertisement of a "plantation, six miles from Greensburg, there are two coal banks on it, one at each end of the place." The Commonwealth, Pittsburgh, Aug. 4,1805: A number of lots were laid off on Saw Mill Run, nearly opposite the first opening made on the Pittsburgh seam. They were from two to twenty acres each "and a great quantity of Limestone and stone coal." Pittsburgh Gazette, Aug. 9, Sept. 6, Sept. 27, Oct. 4, 1811; The Commonwealth, Aug. 19, 1811: Five tracts were advertised that contained coal. One had "fine springs and an inexhaustible mine of coal;" one, "excellent sugar camps, coal banks and limestone and a good mill seat;" one, "good sugar camps, an excellent coal bank and an elegant seat for a distillery;" another, a tract of 45,000 acres in Allegheny and Butler Counties affording "stone coal and iron ore, and seats for water works;" and the last a tract on Beck&apos;s Run, four miles from Pittsburgh "and a coal pit opened about one fourth of a mile from the river." The Mercury, Pittsburgh, April 8, Jan. 14, Feb. 11, 1813; Pittsburgh Gazette, April 16, Dec. 3, 1813: These tracts were advertised during the year in the vicinity of the city. One had "a good sugar camp, woodland and plenty of coal;" another, "a sugar camp and a coal bank on the premises;" while the others were "well timbered or well watered and had excellent stone coal." The Mercury, Pittsburgh, Feb. 2, 1814: A farm was offered for sale on the headwaters of Robinson&apos;s Run, in Washington County, four miles from Burgettstown, containing 60 acres, "a young bearing orchard,... a coal bank and a good sugar camp." Genius of Liberty and Fayette Advertiser, Uniontown, Pa., March 2, 1814, carried an advertisement of a sale of lots in the new town of Perriopolis; "the quantity and quality of the clay, sand and salt licks, near the premises, together with the timber and abundance of .stone coals The town of Perriopolis was situated upon a . farm at one time belonging to Washington.

Jan 1, 1942

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By E. A. Gulbransen, W. S. Wysong, K. Andrew

The reaction of carbon in solid solution in a metal with the surface oxide fim on many metals may be inferred from thermo-dynamic calculations for high vacua and high temperature conditions. Holm has recently shown that oxide films may be removed from ferrous materials by heating in a vacuum at high temperatures and that carbon is the essential element in the reaction. considerable work has been described in the literature on the de-carburization reaction. Several general references may been 2,3,4 However, the nature of the mechanism involved in the decarburization is not well understood. Our interest in this reaction resulted from many attempts to degas and to reduce by pure and dry hydrogen the surface oxides on strips of various types Of chrome-nickel alloys. Some of the early experiments On the behavior Of &apos;3 pct chrome-iron in vacua of the order of 5 X lo&apos; mm and at a temperature Of 600°C have been reported.5 These experi-merits showed a &apos;low reaction with the residual Oxygen Or water vapor in the system and no reaction with hydrogen. This is in accord with thermodynamic data which would lead to the prediction that it is extremely difficult to maintain a hydrogen atmosphere at 600&apos; C pure enough to reduce Crz03 formed On the surface. The crystal structure of the superficial oxide film formed on 13 pct chrome- iron and Nichrome V has been investigated in the thin film range by Gulbransenr Phelps and Hickman,&apos; and shown to be "203. It Was surprising to us to note that when a specimen of Nichrome V containing approximately 80 pet nicke1 and 20 pet chromium was heated to 850°C in a high vacuum, the specimen lost weight. The rate Of weight loss was very temperature sensitive. A study of this reaction in vacua and in a hydrogen atmosphere is the subject of this communication. Type Reactions Let us consider the various reactions which may occur when a metal is heated in vacua, in a hydrogen atmosphere, or in an oxygen atmosphere. The number and kind of reactions will depend upon the chemical nature of the metal, its alloying constituents and the location of the alloying constituents. The metals used in this study are chrome-nickel alloys of the heater type, They consist essentially of chromium, nickel and iron, small amounts of carbon, silicon and manganese and traces of zirconium, calcium, aluminum and magnesium. The trace elements are added to improve the lifetime and other characteristics of the alloy when used as a heater. Seven of the more important reactions with which we are going to be concerned here are as follows: 1. Metal . (gas) F? metal + gas — degassing of the metal 2. zM(s) + y }i Oi(g) M MIOu(s) -oxidation

Jan 1, 1949

By C. S. Roberts

THE advent of a sensitive X-ray method of analysis recently has allowed the determination of retained austenite in amounts as low as 0.3 pct.&apos; As a result this phase has been found in quenched low carbon steels where its presence has not been generally suspected. In the course of a study of the tempering process,&apos; retained austenite determinations were made by the X-ray method on a series of high purity Fe-C alloys and plain carbon steels. The chemical analyses of these materials and details of the hardening procedure are given in Table I. Results were obtained after quenching to 72°F (22°C) and — 321 °F (—196°C). Austenitizing temperatures were between 100" and 150°F above A, or Acm. All proeutec-toid cementite or ferrite was in solution. The combination of the results with those of Averbach, Castleman, and Cohen,&apos; and earlier results of Esser

Jan 1, 1954

By James Gayley

(Wilkes-Barre Meeting, June, 1911.) THE paper presented to the Institute in 1910, by H. 0. Hofman, on Recent Progress in Blast Roasting,1 has called the attention of the iron industry to the adaptability of these processes to the reclamation of by-products such as flue-dust and blue billy, and the better preparation of concentrates and fine ores for use in blast-furnaces. The waste of valuable iron-ore through the production of flue-dust has increased at an enormous rate, and much of it has in reality been wasted as far as future recovery is concerned. Only in recent years has a possible future value been recognized, and the material stored. The increased use of Mesabi ores, which carry considerable fine ore, is principally responsible for the great increase in the production of flue-dust. The amount of fine material that is carried over depends on the fineness of the material and the velocity of the gases, and also to a very great extent on the regularity or irregularity of the working of the furnace. Attempts to recover a part of this loss have been made by recharging a portion of the production into the furnace, but as this material has been once carried out from the furnace, it is naturally in good shape to be carried out again. A recent practice at some works, is to soak the flue-dust thoroughly with water to give it more cohesiveness, but by many this is considered of doubtful advantage in the furnace, and the gases are in consequence heavily laden with moisture. There are vast deposits of magnetic iron-ores in the United States and Canada that are too low in iron for use at the present time, but which can be economically concentrated into very rich material ; in many cases the fineness of crushing necessary to secure proper concentration has prevented their

Aug 1, 1911

By P. T. Gallagher, W. A. Oates

THE partial excess entropy of interstitial solutes in metals, SXS , has usually been interpreted as being principally vibrational ever since the initial statistical treatment of hydrogen in metals by Fowler and Smith-ells. The vibrational entropy is considered being due to the optical modes of the light interstitial atom. Little attention has been given to the magnitudes of the values of SXS&apos;. Leiser and Witte2 and Ebisuzaki and O&apos;Keeffe3 have noted that for hydrogen in metals Si is approximately constant for different metals. On the other hand if it is assumed that the interstitial solute is an isotopic defect then, as shown by McLellan, SXS should vary from metal to metal as follows: where S is the standard entropy of the solvent and Mi, M, are the masses of the interstitial and solvent atoms. respectively. Fair agreement with this equation was found for oxygen in silver and nitrogen in iron4 and for carbon in iron.= Ln a subsequent analysis of metal- hdrogen systems McLellan&apos; found a variation of $&apos; from metal to metal but not in a manner expected from the isotopic impurity equation. However, a possible correlation between the energy of solution, Ei, and sf was noted. Similar correlations have been noted for certain dilute substitutional solid Solutions 7, 8 and recently Kubaschewski 9 has demonstrated a correlation between integral heats and ex-

Jan 1, 1970

By G. V. Sullivan, B. E. Davis, T. O. Llewellyn

The Bureau of Mines, US Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8-10.2% P205 and 1.7-4.8% MgO. Chemical analyses of sized fractions indicated that no pebble concentrate, +1.2 mm (+14 mesh) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0-31.3% P205 at flotation recoveries ranging from 72.4 to 96.1% of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36%. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3% P205 and 0.55% MgO could be produced with a flotation recovery of 89.9%. The MgO content of concentrates obtained from the Manatee No. 1 and Hardee samples was 1.20 -1.36 %, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8%, but with a concomitant loss in phosphate recovery of about 10%.

Jan 1, 1985

By H. C. Vacher

THE limiting concentrations of carbon and oxygen which may co-exist at equilibrium in liquid iron are important in determining the degree to which liquid steel may be refined before it is deoxidized. Most refining processes depend upon the oxidation of a highly carburized iron which invariably results in contaminating the steel with oxygen. The oxygen .thus introduced presents many problems to the refiner, who in turn has attempted to rid the steel of this impurity by deoxidation with elements such as manganese, silicon and aluminum. The importance of the limiting concentrations of carbon and oxygen is accentuated in view of a number of recent researches which have indicated in many instances the existence of relations between oxide inclusions and dissolved oxygen and physical properties and chemical behavior of steel. The determination of the equilibrium concentrations of carbon and oxygen existing in iron under steelmaking conditions is obviously of fundamental importance. It has been generally assumed that the product of the equilibrium concentrations of carbon and oxygen in liquid iron is a constant and that this product is directly proportional to the carbon monoxide pressure in equilibrium with the liquid iron. Herty1,2 has computed values for this product based on open-hearth data which are all in the neighborhood of 0.01 to 0.03 (per cent. FeO X per cent. C) for temperatures in the vicinity of 1550° to 1600 C. and one atmosphere pressure. Kinzel and Egan3 have attempted to determine the value of this product by exposing liquid iron to carbon monoxide at one atmosphere pressure. The value reported by them was 0.0005 at 1550°. C. In. order to apply certain equations to the rate of carbon elimination in the open-hearth process, Feild4 found it necessary to assume. a value of 0.0102 at 1580° C. for this

Jan 1, 1931

By J. L. Walter

Tungsten ingots with and without small amounts of aluminum, silicon, and potassium were prepared by conventional powder-metallurgy techniques and hot-rolled to 0.001-in.-thick sheet. The ingots were rolled three different ways: I) initially cross-rolled, then straight-rolled; 2) straight-rolled, and 3) straig-ht-rolled, then cross-rolled. Total reductions were 99.8 pct. Samples of the sheet were annealed, in vacuo, at temperatures from 1200" to 2200°C. Substructures and textures were determined by transmission electron microscopy and X-ray diffraction. The doping agents were found to form particles of mullite (Al,Si,O,,) which, on rolling., appear to form strings of particles aligned parallel to the rolling direction. These strings of purticles are associated with an increase in the recrystal-lizution temperature from 1400°C for undoped sheet ThE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of drawn and recrystallized wire.&apos;" The grains generally do not occupy the entire cross section of the wire and have lengths many times the wire diameter. The grain boundaries are, in general, nearly parallel to the wire axis and have long &apos;&apos;fingers" projecting one into the other as may be seen in Fig. 1, a longitudinal section of recrystallized doped wire. When unsuitable additions or no additions are made or the wire is not sufficiently reduced during draw- to 2000°C for doped sheet. The particles also limit lateral grain growth while allowing growth parallel to the rolling direction. This results in the formation by primary re crystallization of large highly elongated grains of specific preferred orientation. The undoped sheet recrystallized to small equiaxed gains. The preferred orientations of the large grains were determined from axis density plots to be (113) (691). (0i3) (362), (116) (304) types for the initially cross-rolled then straight rolled material. These orientations are similar to the orientations of the large elongated grains in doped and heavily drawn tungsten wire. The nucleation of the large grains appears to occur by recovery of certain of the polygonized regions of specific orientation, followed by strain-induced boundary migration.

Jan 1, 1968

By J. H. Swisher

The solubility of sulfur and rate of solution of sulfur in pure Lron were measured in H2S + H2 and H2S + H2 H2O gas mixtures. The solubility and diffusivity of sulfur at 1410°Care 0.13 pet S and 1.0 x 10-5 sq cm per sec, respectively. The solubility iS the same, but the rate of sulfurization is slower in the presence of H2O in the reacting gas. Under these conditions, the over-all rate is controlled jointly by a slow surface reaction and by solid-state diffusion; the mechanism for the surface reaction has not been identified. KNOWLEDGE of the behavior of sulfur in solid iron is desirable for the metallurgy of such products as free machining steel, where a high sulfur level is required, and inclusion-free high-strength steels, where the sulfur specifications are very low. The present investigation was undertaken to check previously reported values for sulfur solubility and diffusivity in 6 iron, and to study the poisoning effect of chemisorbed oxygen on sulfurization kinetics in H2-H2S-H2O gas mixtures. All of the experiments were performed at 1410°C. The thermodynamic behavior of sulfur in 6 iron was the subject of a paper by Rosenqvist and Dunicz.&apos; The sulfur solubility at 1400" and 1500°C was determined by equilibrating pure iron specimens with H2-H2S gas mixtures. The maximum solubility of sulfur in 6 iron was alsc determined by Barloga, Bock, and parlee2 by reacting iron wires with sulfur in sealed capsules. In another investigation, the diffusion coefficient of sulfur in 6 iron at temperatures up to 1450°C was measured by Seibel.3 The method used was to measure sulfur concentration profiles in diffusion couples containing radioactive sulfur EXPERIMENTAL Apparatus. A vertical resistance furnace wound with molybdenum wire and containing a recrystallized alumina reaction rube was used for the experiments. The hot zone in the furnace was approximately 2 in. long with a temperature variation of ±3oC. The hot zone temperature was automatically controlled to within ±2°C, and the test temperature was measured with a pt/Pt-10 pet Rh thermocouple before and after each experiment. Flow rates of the reacting gases were obtained using capillary flow meters. Materials. The source of H2S in the gas train was a premixed cylinder containing 5 pet H2S in H2. This mixture then was diluted with additional hydrogen and argon. In some experiments, water vapor was introduced by passing hydrogen and argon through a column containing 10 pet anhydrous oxalic acid and 90 pet oxalic acid dihydrate. The vapor pressure of water above this mixture is well-known.4 Argon was used as a diluent to minimize thermal segregation of H2S in the furnace5 and to reach higher H2O:H2 ratios than could be obtained in mixtures of H2 and H2S alone. Argon was purified by passage over copper chips at 350°C and subsequently over anhydrone. Hydrogen was purified by passage over platinized asbestos at 450°C and then over anhydrone. The H2-H2S mixture was purified by passage over platinized asbestos and then over P2O5. The specimen stock was made by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zirconia crucible. The principal impurities are listed in Table I. In some of the equilibrium experiments, six-pass zone-refined iron was used to minimize impurity side effects. This zone-refined iron had a total impurity level of about 25 ppm. Procedure. Specimens were annealed in hydrogen for a period of at least 2 hr at the beginning of each experiment. The specimens were held in the reacting gas for times varying between 10 min and 17 hr, and cooled to room temperature in a water-cooled stainless-steel block at the bottom of the furnace. The pH2S/pH2 ratios reported are those for gas equilibrium at 1410°C. Calculations based on available thermodynamic data8 showed that the only other gaseous8 species that formed in significant amounts in the furnace were S2 and S. Even when water vapor was introduced into the gas mixture, the concentrations of SO2, SO, and so forth, were negligible. The initial partial pressure of H2S was therefore corrected for its partial dissociation to S2 and S in determining the equi-

Jan 1, 1968

By H. M. Davis, T. S. Jones

A methodfor accelerating the reduction of a metal oxide by carbon monoxide is to incorporate in the reduction system a nonreducible oxide which has a strong affinity for carbon dioxide and will remove it from the product gases. The effectiveness of this method was investigated by veduction experiments on specially prepared powder mixtures of SrO-ZnO ("active&apos;.) and SrCO3-ZnO (reference). Measurements at 750o and 677°C showed that the rate of reduction of ZnO by CO was as much as an order of magnitude greater in the presence of SrO. Under the experimental conditions at least as much CO2 as generated by veduction was absorbed when SrO was present. Enlzancernent of the veduction rate by SvO resulted from modification of&apos; gaseous djfitsion processes. THE specific question posed in this investigation was whether the reduction reaction CO + ZnO - Zn(g) + COa [1] could be accelerated by incorporating strontium oxide into the oxide charge undergoing reduction. Provided the strontium oxide was active enough, it could remove carbon dioxide from the product gases of ( 11 and form strontium carbonate, thus modifying Reaction [ 1] to CO + ZnO + SrO = Zn(g) + SrCO3 [ 2] This study of the comparative rates of Reactions [ I] and [2] can be considered as a particular case of a general scheme for increasing the rates of reduction of metal oxides by carbon monoxide. The limits of applicability of this scheme are indicated in the simple thermodynamic analysis presented in the appendix. This analysis primarily dictated the choice of the system, CO-ZnO-SrO, employed in this investigation. In addition, it was thought that a study of this scheme by use of the CO-ZnO-SrO reaction system would be of special interest in view of indications in the literature1-3 that the gaseous reduction of zinc oxide is prone to rate control by diffusion in the gas phase. The distinction should be pointed out between this and other efforts to increase the rates of reduction reactions through the use of addition agents. Additions of a wide range of chemicals have been tried with de- grees of apparent success varying from slightly negative to highly positive. The reasons for making additions have included the use of salts to produce effects akin to catalysis,4, 5 the alteration of the microstruc-tural details of the reduction process (including solid-state diffusion),6-8 and the conversion of an en-dothermic reaction into one that is exothermic or autogenous.9-12 The means used to attempt alteration of the enthalpy change has commonly been to incorporate lime into the charge, so that heat is generated by reaction with either of the reaction products, carbon dioxide or water. The use of lime in this way makes endeavors such as that of Edstrom and Wiberg similar to the present one. Furthermore, the basic principle behind the present work has previously been set forth.13 However, a detailed investigation of the type of reaction described in this work does not appear to have been conducted. EXPERIMENTAL PROCEDURE From both conceptual and physical standpoints, Reaction [2] is to be considered as the sum of two reactions:

Jan 1, 1968

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

In a previous study of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is 2 more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about I to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, I per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to I-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudo-martensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously1 that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943

By Walter Crafts, C. M. Offenhauer

IN a previous study&apos; of the carbide phase of chromium steels, it was shown that chromium carbide (Cr7C3) is a more stable carbide than cementite (Fe3C) at tempering temperatures above about 500°C. in quenched steels containing from about r1to 7.5 per cent chromium. Below this temperature the carbide phase was found to consist of cementite in all of the steels examined. In the present investigation it was found that a similar change in the carbide phase takes place in molybdenum and in chromium-molybdenum steels at approximately the same tempering temperatures. The approximate ranges of occurrence of the alloy carbides Cr7C3, Cr4C, and Mo2C have been determined in steels containing up to 5 per cent chromium, 1 per cent molybdenum and 0.60 per cent carbon. The experimental steels were made in small high-frequency furnaces from Armco ingot iron, low-carbon ferrochromium and calcium molybdate and were poured into 2-in. ingots, which were forged to 1-in. round bars. Sections of the bars were heated to the carbide-solution temperature and cooled rapidly to induce austenite transformation at relatively low temperatures. The steels were subject to some segregation, therefore comparatively high temperatures were necessary to dissolve all of the carbides. The microstructure of the quenched specimens was examined to verify the belief that the carbides had been dissolved, and also to determine the nature of the nonmartensitic structure of incompletely hardened steels. Ferrite and pseudomartensite were present in some of the specimens, but all specimens were quenched at such a rate that pearlite was not formed, in order to ensure the formation of the carbides at temperatures lower than about 500°C. It had been found previously&apos; that in chromium steels the chromium carbide could be produced by transformation of austenite in the pearlite range above 500°C., and, in order to start the tempering treatment with the carbide present as cementite, the absence of pearlite was considered to be essential. The specimens were tempered for 64 hr. to permit the formation of the stable carbide. After tempering, the specimens were submitted to microscopic and X-ray examination. The carbides were separated either electrolytically in a 5 per cent HCl electrolyte or with an acidified copper-potassium chloride solution. The crystal structure of the carbide phases was determined by the Debye-Scherrer type of X-ray patterns. The X-ray patterns obtained from specimens near the boundaries between two types of carbides were generally weak and diffuse as compared with the other patterns. For this reason, and because the more soluble components may be masked, the boundaries between the phases could not be determined precisely. However, the X-ray analysis of electrolytically separated carbides has given consistently reproducible results

Jan 1, 1943