Search Documents

By R. F. Mehl, C. S. Barrett, A. H. Geisler

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By R. M. Waterstrat

The phase VPt has been reported to have a crystal structure of the B19 (AuCd) type at low temperatures.''' A recent investigation3 has indicated that this phase forms by an ordering reaction from the disordered fcc Pt(V) solid solution which is stable at high temperatures. olander4 has shown that there exists a close structural relationship between the orthorhombic B19 structure and a fcc structure possessing the L1 , (CuAu) type of atomic ordering. One may derive the B19 structure by a shear-like displacement of the atoms in the (002) plane of the ordered fcc lattice along the (010) direction through a distance equal to one eighth of the unit cell dimension, see Fig. 1, followed by an orthorhombic distor; tion of the cube axes such that a = 2.693A. h = 4.413A. and c =4.767A (estimated uncertainty 0.005A). Filings of this phase were produced by grinding a VPt alloy having the B19 structure with a diamond dental grinding disc. When these filings were subjected to X-ray diffraction examination, a pattern of a severely cold-worked fcc structure was obtained. higher solution temperature used (1200 C) or to a much lower oxygen pressure than he reported, due to transfer through many bends and tubes in his complicated apparatus. An interesting observation was made when an oxygen addition was attempted in a cylindrical sample of columbium in the cold worked condition rather than in the annealed condition. The interior of the sample re-crystallized during the oxygen addition at 900°C. The periphery, however. (1 mm) did not recrystallize. A similar sample without oxygen recrystallized throughout the entire cross section. It appears that the re-crystallization is hindered by interstitial oxygen. Presumably, the interior recrystallized before appreciable oxygen could diffuse into the core. This work was supported by the United States Atomic Energy Commission. When the filings were annealed in a high vacuum furnace for 15 min at 110O0C, however. they returned to the B19 structure perhaps as a result of reordering. Subsequent less-severe cold-working of these filings by grinding in a hardened steel mortar and pestle at room temperature produced a transformation into a cold-worked L1, structure which was slightly tetragonal. Thus it appears that the degree of deformation may influence the final structure. Considerable line-broadening was observed in X-ray diffraction patterns obtained from the cold-worked filings and therefore no attempt was made to obtain accurate lattice parameters. Vacuum annealing treatments at 1100'C intended

Jan 1, 1970

By John D. Roach

DURING an investigation of the yttrium-hydrogen system aimed at producing solid yttrium hydride specimens containing various amounts of hydrogen, it was observed that yttrium containing approximately 2 wt pct H exhibited a tendency to crack and crumble to a powder on standing in air at room temperature. It was also observed that longer hydriding times, at a given temperature, increased this susceptibility to powdering without an increase in hydrogen content, also that moisture in the air is necessary for the observed effects to occur. Even if cracking did not occur, there was a continual formation of a light gray powder on the as-treated surface of the hydrided yttrium and this reaction continues until the entire hydrided piece has been reduced to a powder. Storing the hydrided specimens in the absence of air or removing the surface either by machining or grinding were effective means of preventing this disintegration of hydrided yttrium. In an attempt to determine the reason for this powdering phenomenon, the surfaces of a number of as-hydrided yttrium specimens were examined by X-ray techniques. In all cases the X-ray pattern obtained showed the major phase to be yttrium hydride (YH2) as would be expected since the specimens contained 2 to 2.2 wt pct H. In some cases a trace of yttrium oxide was observed. There was also a third phase present on the surface of these hydrided specimens which could not immediately be identified. This unknown phase was a face-centered cubic material, NaC1-type structure, with a lattice parameter of 4.855 and a calculated density of 5.914 g per cc. Very slight hand polishing of the surface of the hydrided yttrium specimens completely removed both the unknown phase and the traces of oxide so that only the yttrium hydride pattern remained. Based on the X-ray patterns the quantity of the unknown phase on the surface of the hydrided yttrium appeared to be directly related to the susceptibility of the material to powdering. Work at the Denver Research Institute on the yttrium-nitrogen binary system showed that yttrium nitride (YN) is a face-centered cubic material with a lattice parameter of 4.878A and a density of 5.890 g per cc. They also noted that this compound rapidly disintegrated to a powder on standing in air. The unknown pattern observed in the above specimens corresponds very closely to that of the nitride—fcc structure, 4.885 parameter, and density of 5.914 g per cc. The presence of this thin film of nitride on the surface of the hydrided specimens probably accounts for the observed powder formation and crumbling. The nitride reacts with the water vapor in the air (verified by private communication from Dr. C. Huffine, General Electric Co.) to yield yttrium oxide and ammonia. Ammonia is readily detected when hydrided yttrium specimens were allowed to stand in bottled moist air. The powder formed on the surface of the hydrided specimens was shown by X-ray analysis to be yttrium oxide. This reaction appears to occur primarily at the grain boundaries since discrete particles of yttrium hydride separate from the specimens during this powdering process. The reaction of yttrium nitride with water vapor is believed to be as follows: 2YN + 3H2O - Y203 + 2NH3. Despite the fact that this nitride is present only as an extremely thin surface film, if the above reaction is not prevented by removing this film from the surface either by machining or grinding, the reaction continues until the entire hydrided piece has been reduced to a powder. To account for this continuation of the reaction, it is believed that the following reactionalsooccurs: 2YH2 + 2NH3 -2YN + 5H2. The nitride produced by the latter reaction reacts in turn with water vapor. The reaction therefore becomes autocatalytic and continues until the hydride has been consumed and the entire piece reduced to oxide powder. The amount of nitride required to initiate this reaction is quite small and this nitrogen contamination can occur from a number of sources—hydrogen gas employed, minute leak in the hydriding apparatus or even from degassing of the reaction vessel itself. Longer hydriding times increase the possibility of nitrogen contamination and this is especially true when a dynamic gas system is employed in the hydriding process. The production of stable, solid hydrided yttrium is dependent on the complete absence of nitrogen contamination during processing. If such contamination does occur, powdering of the hydrided product can be prevented by removing the nitride from the surface e.g. grinding or by preventing access of air to the pieces e.g. sealing in wax or plastic. The author wishes to express his appreciation to General Electric Co. for sponsoring this research and for permission to publish the results of work under Subcontract AT-93.

Jan 1, 1962

By B. Silliman

The experiments detailed by Dr. Hunt,* having demonstrated the fact that the copper contained in the "clay ore" of Jones's Mine, was rendered completely soluble in the bath of ferrous chloride, used in the Hunt and Douglas process, after heating in contact with carbonaceous matter in a close vessel, I set myself to devise a form of muffle furnace adapted to the treatment of large quantities of these and similar ores by a continuous process. The result is shown in the diagrams on Plate X, reduced from the working drawings, after which this furnace was built early in 1876, at Phœnixville, by the Chemical Copper Company on their works at this place. The peculiar character of this ore determined the form, dimensions, and position, with reference to charging and discharging of these muffles. The ore arrived from the mine with from 20 to 25 per cent. of moisture, and when dried at 21o F., or more slowly at lower temperature, it falls to a light incoherent powder, with occasional lumps of undecomposed rock. In this condition it is readily mingled with coal-dust or any like reducing agent, and requires no other preparation for the muffle than the use of the shovel, to mix it well with the reducing agent. As it is a remarkably good non-conductor of heat, it was obvious that the mass, to be heated through in a reasonable time, must not be too thick, while the weight of the mass must be sustained in a way to avoid undue strain upon the walls of the muffle. These walls must be as thin as practicable, to favor the more rapid transmission of heat, and must, therefore, be so constructed as to admit of being stayed on the sides at frequent intervals to resist the lateral thrust of the very mobile mass of pulverulent ore, which, for obvious reasons, must be charged at the top and drawn from the bottom of each chamber. These considerations led to the form adopted, viz., two vertical muffles, standing upon very strong bridge tiles, seen in longitudinal section, on the line E, F, and in plan in Fig. 3, on the same plane. (Plate X.) The vertical section of the muffle is seen in Fig. 4, drawn in the plane G, H, of the longitudinal section, Fig. 6, which is the key to all sections. The walls of the muffles are built of the best firebrick, very care-

By C. Land, R. Hultgren

Heat contents of four Cr-Ni alloys were determined in a diphenyl ethev calorimeter. Aside from ferromagnetic effects, Kopp's law of additivity of heat capacities is approximately fol-lowed, in disagreement with earlier results of A. W. Foster. In 1934 Foster1 reported heat-capacity measurements of dilute solutions of chromium in nickel, primarily as a study of the effect of alloying on the ferromagnetic Curie temperature. He found that, apart from the Curie temperature effect, the general level of heat capacities was reduced 10 pct by the addition of 1 pct Cr; 20 pct by the addition of 2 pct Cr. His measurements of pure nickel essentially agreed with accepted values. These results indicate that small amounts of dissolved chromium cause an increase in the Debye temperature of nickel, presupposing a change of frequency of interatomic bonding vibrations which is much larger than should be expected. If Foster's results were verified, therefore, they would have important implications for bonding theory. The only other heat-capacity measurements in this system seem to be those of Taylor and Hinton,' who studied anomalies which they attributed to super-lattice formation at 25 at. pct Cr. At temperatures above the anomaly, Taylor and Hinton found heat capacities at this composition were quite normal, approximately obeying Kopp's law of additivity. EXPERIMENTAL WORK In order to verify or disprove the remarkable results of Foster, the heat contents of four dilute solid solutions of chromiunn in nickel were measured in a diphenyl ether calorimeter. This instrument, described elsewhere,, operates on the principle of the Bunsen ice calorimeter, but uses diphenyl ether as the working substance. Diphenyl ether melts at the convenient temperature of 26.S°C and supplies a more sensitive measure of heat than ice. The hot sample, in an atmosphere of argon, is dropped from a furnace at a measured temperature into a chamber which is surrounded by a mixture of solid and liquid diphenyl ether. The heat from the hot specimen melts some of the solid without chang- ing the temperature of the calorimeter. The amount of solid melted, and therefore the number of calories released by the specimen, is measured from the increase of volume of the mixture, which pushes mercury down a graduated capillary tube. The apparatus has been standardized against the known heat content of pure platinum. Heat loss during the dropping of the specimen was estimated by comparing the heat content of an empty platinum capsule with a solid platinum ball of the same radius and degree of polish of the surface. Repeated tests demonstrate the precision of measurement to be closer than *0.3 pct. Smoothed experimental results are listed in Table I. The tabulated values for pure nickel are taken from kelley, several measurements were made which agreed closely with this tabulation. For chromium, however, no similar agreement was found. The values tabulated were taken from a thorough study of chromium with the diphenyl ether calorimeter which will be published elsewhere.= Suitable plots of the data showed the expected ferromagnetic anomalies in the low-chromium alloys, while the 11 pct alloy shows no ferromagnetic anomaly, but a different, small anomaly below 900°K. This is perhaps the same anomaly found in CrNi, which was once attributed to superlattice formation,' but is probably due to some other cause, such as antifer-

Jan 1, 1960

By Joachim J. Hauser

William F. Hosford, Jr. (Massachusetts Institute of Technology)—Dr. Hauser has used a very interesting method to study the interaction of dislocations on different slip systems, but it should be pointed out that the analysis of the experiments is subject to a serious criticism. He states that "the effect of the compression can be adequately described by one slip system." The effect of frictional constraint during the compression makes this quite unlikely. When a block of metal is compressed its lateral expansion requires a sliding of the metal over the compression platens. The role of friction in the interface between the deforming metal and the platens is to increase the normal force required for the compression. Analyses1213 have shown that, in general, the additional force, p, required for the compression is a function of l/h where is the coefficient of friction, I is the length of the speci- men in contact with the platens. For a constant COefficient of friction, isho' shows that P should increase exponentially with pl/h for both plane strain and axially symmetric compression. For a compression specimen, Fig. 7, whose cross section perpendicular to the compression axis is a rectangle whith one dimension L, much larger than the other W, a much larger force would be required for appreciable flow parallel to L than for flow parallel to U7. Therefore lateral strain in the W direction, EW, should be much greater than the lateral strain in the L direction EL. Since L/H = 14.5 for Dr. Hauser's crystals, and since no lubrication was used, it seems questionable that appreciable lengthening of the crystals could occur. Because the theories of frictional constraint have been derived for isotropic polycrystalline materials, it was decided to make experimental measurements on a single crystal. A section 3.590 in. long was sawed from an aluminum single crystal with a square section of 0.249 in., so that L/W= 14.4. This crystal was tested in compression between dry ground steel platens. Fig. 8 shows the orientation of the crystal and the axis of compression. The face for compression was chosen so that the operation of the single-slip system which would be predicted in the absence of friction would lead to a larger strain in the length direction than in the width direction. The dimensional changes of the width and length as well as the height were measured frequently during the compression with micrometers. Width strains were calculated from the average of readings near each end and at the center. A plot of the length strain, EL, against the width strain E w is given in Fig. 9. The slope indicates that the EL amounted to only 2.5 pct of cw. Other compression tests on similar crystals with shorter lengths also showed severely limited elongation. Even for a crystal with L/W = A.0, EL was only about 26 pct of cw. Because of the frequent interruptions of the tests for dimensional measurements should have decreased the frictional constraint by allowing a reseating of the platens, even smaller elongations under continuous testing seem probable. These tests on long narrow crystals show that essentially plane strain conditions prevailed. We may assume that Dr. Hauser's crystals deformed similarly. That the compression can be described by the

Jan 1, 1962

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By John Griffen

This paper records over twenty years' experience with the use of the Rheolaveur system in the United States, showing its ability to meet changing conditions caused by the dirtier mine output of present-day mechanical mining methods. Data are given on size ranges handled, number and capacity of units installed, maintenance experience, and operating results on two-product and three-product separations. IT is not the purpose of this paper to discuss the principles employed in the Rheolaveur system of fine-coal cleaning as these have been fully covered in the technical literature of the Institute."2 Rather, our purpose will be to record the highlights of over 20 years' experience in the United States with Rheolaveur fine-coal launders, which will indicate their capabilities and costs of cleaning and their adaptability to meet the changing conditions caused by present-day mechanical mining methods. Rheolaveur fine-coal launders are used in the United States to treat a wide variety of size ranges of fine coal, the coarsest being 1/2 in. to 0 and the finest about 1/8 in. to 0. In Europe feeds as coarse as 5/8 in. and as small as 1/2 mm (28-mesh) to 0 are being cleaned. The size ranges usually handled in this country are 3/8 to 1/4-in. round to 0. Thirty five units with a combined hourly feed capacity of 3200 tph have been installed in the United States. Individual units are cleaning as little as 25 tph, while others are cleaning as much as 200 tph. Rheolaveur fine-coal launders offer cleaning units of high capacity and are outstanding in requiring a minimum of building space per ton of input. Experience has shown that maintenance costs are low. Several installations were made in the Pittsburgh district from 1928 to 1930, and since that time operation has been largely two shifts per day. Minor repairs to liner plates and Rheo boxes have been required during the intervening years, but no major replacement of launders was required until 1947 and 1948. At one of these plants, launders operated for 17 years before they were replaced and during that period over 26,000,000 tons of —5/16-in. coal were cleaned. The effect of the much dirtier raw coal produced by mechanical loading of the Pittsburgh seam is shown by the following tests. The data in table I summarize the performance of a Rheo fine-coal unit when cleaning hand-loaded raw coal. The —4-in. raw coal fed to the cleaning plant analyzed only 8.16 pct ash and 1.31 pct sulphur and contained 4.6 pct sink, 1.55 sp gr. Two years later, in 1945, mechanically-loaded coal from the same mine was cleaned in the same plant. The feed, —4 in., then analyzed 20.10 pct ash and 1.53 pct sulphur and contained 20.2 pct sink, 1.55 sp gr. The performance of the Rheo fine-coal unit when cleaning this coal is given in table 11. It will be noted that the +48-mesh coal is cleaned almost as thoroughly as in table I. The large amount of high-ash slimes produced from the dirtier feed are responsible for the higher ash of —--48-mesh washed coal in table 11. In this plant the Rheo fine-coal unit did not get the full load of refuse resulting from mechanical

Jan 1, 1951

By B. D. Cullity, O. P. Puri

The magnetostrictia of nickel after increasing amounts of plastic elongation was measured at field strengths up to 1500 oe. In addition, the residual stress was measured by means of X-ray line shifts. The observed decrease in magnetostriction following plastic strain is shown to be associated with residual compressive stress. If a metal bar, whose longitudinal axis is taken as the x direction, is plastically elongated in the x direction and then unloaded, X-ray diffraction measurements will indicate the presence of a residual compressive macrostress 0%. However, stress measurement by means of mechanical relaxation does not reveal any macrostress. In a previous paper1 the fictitious macrostress indicated by X-rays was ascribed to a particular distribution of micro-stress, namely, one in which the bulk of the material was stressed more or less uniformly in compression and a very small portion in tension. It was shown that this distribution would account for Neurath's measurements2 of magnetic losses in silicon steel, because of the effect of residual stress on magnetostriction. The present paper is concerned directly with magnetostriction, in nickel, and with the effect on magnetostriction of the residual stress created by plastic elongation. The residual stress was determined by measurements of X-ray line shifts. MATERIAL AND METHODS Commercially pure "A" nickel was investigated. Its nominal composition, in weight percent, is 99.4 Ni + Co, 0.2 Mn, 0.15 Fe, 0.1 Cu, 0.1 C, 0.05 Si, and 0.005 S. Magnetostriction was measured by means of SR-4 electrical-resistance strain gages mounted on specimens 1/4 in. sq and 8 in. long. Magnetic fields up to about 1500 ce were provided by a multilayer, non-cooled solenoid. A considerable amount of heat was developed at the higher field strengths, and, to avoid errors due to changes in the specimen temperature, the following procedure was adopted. Each measurement of the magnetostriction X at a particular field strength H was preceded by demagnetization and an adjustment of the strain indicator to zero; the field H was then quickly switched on and the strain read immediately. Curves of ? vs H were flat for field strengths above about 750 oe for all specimens, and this constant value of X was accordingly taken as the saturation magnetostriction ?s The X-ray measurements of residual stress were made with a Norelco diffractometer on specimens cut from flat bars 1 1/4 in. wide, 1/8 in. thick, and 12 in. long. These measurements were confined to lattice planes parallel to the surface of the specimen. Two reflections were studied: the 311 CrKß line at 28 = 157 deg, and the 420 CuKal line at 28 = 155 deg. The line centers were determined by fitting a parabola to the peak of the line, as suggested by Ogilvie3 and as modified by Koistinen and Marburger.4 The CuKa doublet from the plastically elongated specimens was first resolved by the Rachinger method5. All X-ray measurements were made by counting at fixed angular positions. RESULTS The results of the magnetostriction measurements are shown in Fig. 1 and Table 1. The magnitude of

Jan 1, 1963

By E. Bicknese, R. Clark

The mechanism and rate of reduction of FeO at conditions similar to those in the stack of a blast furnace have been determined for temperatures from 980" to 1165°C. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal in a static system (no flow of reducing gas) have shown that the CO2-CO ratio of the product gas depends upon the relative reactivities of the Fe2O3 and charcoal. In a systern with a "hot blast" of CO and Nz (simitar to dry bosh gas), synthetic FeO, and actiuated coconut charcoal, the rate of reduction was not sensitive to the flow of reducing gas, and the rate-controlling step alas the chemical reaction at the metal-oxide interface. Wherz solid carbon was not present, a critical flow rate of reducing- gas had to be met in order to prevent a lowering of the reduction rate. The effect of a less-reactive carbon (blast-jurnace coke) and of a "natural" FeO on the mechanistn and rate, and the mininum amount of carbon necessary in the charge to tnaintain the reducing potential of the gas phase, have been determined. THE importance of iron oxide reduction processes has encouraged many studies of the process reaction kinetics. Despite this, the mechanism is not well-understood and three main theories have evolved, which can be stated as follows: A) the rate-controlling step is diffusion, either gaseous diffusion of the reductant or product gas through a porous solid,' or solid-state diffusion of iron and oxygen atoms through the so1id.2 B) The slow step is diffusion of reducing gas through a stagnant boundary layer. C) The reaction rate is controlled by the chemical reaction occurring at the metal-oxide interface and is proportional to the area of this interface.3 By increasing the velocity of the reducing gas to a flow rate beyond which no increase in the reduction rate is observed, critical flow rate, it may be possible to eliminate B as the slow step. However, as warnere points out, the establishment of a critical flow rate may only assure that the reaction is not limited by a reduction in the reducing potential of the gas and that B may still be the rate-determining step. Edstrom and Bitsianes and Seth and Ross8 show that A and C may both be correct for the reduction of the same oxide, depending upon the stage of the reduction, and that the relative importance of the two mechanisms varies with the porosity of the oxide. Themelis9 has derived expressions which express A, B, and C in terms of the fraction reduction, Rx, of a spherical particle. Thus, in the case of A a plot of In (1 - Rx) vs time must be linear and the time to reach a given reduction is proportional to the square of the particle diameter. For B a plot of (1 - Rx) vs must be linear and the time to reach a given reduction is proportional to the square of the diameter. For C a plot of 1 - (1 - RX)1/3 vs f must be linear and the time to reach a given degree of reduction should be proportional to the diameter. In the case of mixad controlled reactions, none of the plots are linear over their entire length. The results of previous studies, in which the rates of gaseous reduction of iron oxide were measured in the absence of carbon, may not correspond to blastfurnace practice because they ignore the effects of the Boudouard reaction. CO2 +C — 2CO The presence of carbon may alter the mechanism or the rate of iron oxide reduction through an enrichment of the gas phase by Eq. [1]. In this case, the presence of and reactivity of carbon become important. If the Boudouard reaction has no effect on the rate of reduction, the reducing gas could be supplied by some means other than the gasification of carbon at the tuyeres and carbon could, theoretically, be eliminated from the burden. Preliminary studies of the reduction of Fe2O3 with activated coconut charcoal were made to determine if the reactivity (surface area) of the Fe2O3 had any effect on the product gas composition. Two size fractions of Fe2O3 were reduced with charcoal in a static system (no flow of reducing gas). In each case the charcoal was -100 + 325 mesh and was 25 pct of the total charge. One fraction of the reagent-grade Fe2O3 was submicron in diameter. The other fraction was -100 + 200 mesh and was prepared from the former by compacting, sintering at 1300°C, crushing, and screening. In each experiment, the reaction vessel was filled with a mixture of CO and CO, which would be in equilibrium with FeO and iron at the reaction temperature. A furnace was heated to the desired temperature, the vessel was placed in the furnace, and the gaseous products of the reaction were collected and analyzed. The results of these experiments, Fig. 1, show that the gas phase associated with the submicron oxide is more oxidizing than that with the -100 + 200 mesh oxide. Therefore, in a static system, the relative rates of the reduction reaction and the gasification of carbon depend upon the reactivities of the Fe2O3 and charcoal. The reduction of FeO to iron is the most important reaction occurring in the blast furnace and is probably the slowest of the several reduction steps. The mechanism and rate of reduction of FeO in a system containing carbon and a flow of dry bosh gas have been studied. TRANSACTIONS OF THE METALLURGICAL SOCIETY OF AlME

Jan 1, 1967

By EDWARHD HALSE

Discussion of the Paper of Dr. H. M. Chance, presented at the Lake Superior Meeting, September, 1904. EDWARD HALSE, Puerto Berrio, Colombia, So. Amer. (communication to the Secretary*) : The Taviche mining-district is generally known as a Taviches," being named from the two villages called respectively San Pedro Taviche and San Jeronimo Taviche. It is so called by José G. Aguilera, in his paper on the Geographical and Geological Distribution of the Mineral Deposits of Mexico;' and in published reports by the late N. W. Rudston Read ;2 and by Juan de Dios Villarello.3 The region is a large one, measuring about 24 miles long and 7 miles wide. Dr. Chance, in his interesting paper, tells us very little about the nature of the ores, and, with regard to the geology of the district, contents himself with observing that ? the country, as a rule, consists of eruptive rocks; and no evidences of sedimentary strata appear near the mines.? The latter part of the above statement is hardly correct. The formation is mainly eruptive, being hornblende-audesite of Tertiary age, which is limited on the east by the calcareous (Cretaceous) formation, and on the west by the Huronian rocks of Ocotlan. Limestone is seen close to the Santa Càtarina mine, at the northern end of the region. In the surface-working known as La Cueva, a little northeast of San Pedro, limestone forms the eastern wall of the deposit which consists of spots (moscas) of pyrargyrite in white opaque or transparent quartz. Ill one place the ore is associated with stibnite, and the quartz frequently exhibts a

Sep 1, 1905

By L. K. Jetter, C. J. McHargue

The use of axis charts for representing the texture of cold-rolled thorium sheet was compared with conventional pole figures. Four texture components were deduced from the axis charts and shown to be consistent with the pole figures. It was shown that consideration of the pole figures alone could lead to an apparent component which is the average of two actually present. It was also shown that the spread about the "ideal" textures and the amount of material associated with each could be readily obtained Fom the axis chart method. BECAUSE of the crystallographic nature of the deformation mechanisms in metals, plastic flow results in the alignment of certain crystallographic directions with the primary flow directions. In the study of the "preferred orientation" thus developed, one wishes to discern the distribution of the crystallographic directions with respect to some reference direction, usually a direction related to the fabrication procedure, such as the rolling direction. The pole-figure method, introduced by ever,' involves the plotting of the distribution of the poles of some family of planes on a stereographic projection which places the reference direction(s) at the north pole and/or in the center. By noting the angles between the reference directions and concentrations of poles on several such pole figures, one can deduce the crystallographic directions which are aligned with the reference directions. If the preferred orientation is relatively simple and well-developed, one to three pole figures may be sufficient for obtaining the desired information; if there are several texture components, more pole figures may be needed. A significant improvement in the method of representing the textures in wires and rods resulted from the introduction of the "inverse pole figure" or axis-distribution chart by Harris.2 Such a chart gives directly the distribution of the reference axis relative to the standard stereographic projection. There has been widespread acceptance of this method for the representation of fiber textures, and methods have been proposed for converting observed diffraction intensities into axis densities.2-6 The suggestion by Mitchell and Rowland3 and Jetter, McHargue, and williams5 that sheet textures could be represented as distributions of rolling, normal, and transverse directions have been criticized on the basis that they offer no significant advantage over a combination of two ordinary pole figures and that it has not been proved that sheet textures can be treated as quasi fiber textures.6 If the purpose of a texture determination is to study some property which is related to the orientation of a particular crystallographic plane or direction, then conventional pole figures certainly are sufficient. For example, the distribution of the slip planes in face-centered cubic metals (the (111) pole figure) serves to indicate the variation in mechanical properties of sheet. On the other hand if the study is directed at an understanding of the factors influencing texture formation, it is desirable to know not only the preferred orientation but the kind and degree of spread from it and the relative amounts of material in each component, if there are more than one. Axis charts give this information as well as the orientation distributions. Consider the procedure for deducing a texture component from a pole figure for the (111) planes

Jan 1, 1961

By Carl Wagner

This paper contains solutions of the differential equation of diffusion in binary alloys if the diffusion coefficient is an exponential function of the concentration of one of the components. THE general differential equation for one-dimensional diffusion in a binary system can be written as: where c is the concentration of one of the two components in any suitable units; x, the distance from a reference plane; t, time; and D, the diffusion coefficient. Hartley and Crank&apos; have pointed out that eq 1 with conventional length units for measuring the distance x holds only if the alloy can be regarded as a rigid framework. In general, this is not the case, especially if the lattice parameter varies appreciably with composition. If a modified coordinate system is used instead of an orthodox system based on the centimeter a:: length unit, eq 52 is obtained, which has the same general form as eq 1 and is generally valid. The necessary transformations are presented in the appendix. If&apos; D is independent of concentration, analytical solutions of eq 1 are known for numerous boundary conditions. If D depends on concentration, solutions based on known analytical functions are not available. Among others, Boltzmann2 and Matano3 have shown that the concentration c depends only on (x/t1/2) in the case of diffusion between two semi- infinite spaces with uniform initial concentrations: c = c, for x < 0, t = 0, i.e., x/tl/2 = — x [21] c = c2 for x > 0, t = 0, i.e., x/tl/2 = + a Moreover, Boltzmann and Matano have shown how D may be calculated as a function of concentration over the whole range of composition from c -c, to c = c2 if c as a function of (x/t1/2) for the initial conditions stated in eq 2 has been determined experimentally. Thus, for instance, in principle, the diffusion coefficient in silver-gold alloys may be calculated as a function of concentration for the whole range of composition from only one diffusion experiment with a couple of pure silver and pure gold welded together. If the diffusion coefficient D as a function of concentration c is known, a solution of eq 1 for boundary conditions as stated in eq 2 with arbitrarily chosen values of c, and C2 may be wanted. For instance, if the diffusion coefficient in an alloy A-B as a function of concentration has been derived from an experiment with a diffusion couple involving 0 and 30 pct B as initial. concentrations, the calculation of the concentration distribution in a diffusion couple involving other initial concentrations, e.g., 5 and 20 pct B, may be desired. This problem may be solved by numerical or graphical integration of eq l. The solution of an ordinary differential equation of second order, which results from using (x/t1/2) as an independent variable, can be computed quite rapidly if two conditions for the same value of the independent variable are given. In eq 2, however, two conditions are given for two

Jan 1, 1953

The following advertisements show the contemporary view of the value of coal on a tract, usually as compared with farming advantages of several kinds. Fayette Gazette and Union Advertiser, February 10, 1798: "For Sale in Washington twp., Fayette Co., 211 acres of land whereon is a good new grist merchant mill, a good stone dam, and a house for the miller, about two acres of bottom, cleared and fenced, an excellent coal bank and saw-mill seat unimproved." Pittsburgh Gazette, March 19 and 26, 1802: Ads. offering for sale two properties, one of 38 acres, "together with a Coal Pitt and Lime Quarry, lying on the Monongahela side of Grant&apos;s Hill, and within one mile and a half of Pittsburgh," and the other two tracts of 700 acres on "Racoon creek, contiguous to which is a valuable limestone quarry, and a quarry of building stone, also plenty of stone coal." Pittsburgh Gazette, Oct. 8, 1802: A farm between Pittsburgh and Greensburg "with house, barn and a Smith shop-also, a fine sugar camp, and a Coal Bank within sight of the house," was offered for sale. The Farmers Register, Greensburg, Pa., March 13, 1802: An advertisement of a "plantation, six miles from Greensburg, there are two coal banks on it, one at each end of the place." The Commonwealth, Pittsburgh, Aug. 4,1805: A number of lots were laid off on Saw Mill Run, nearly opposite the first opening made on the Pittsburgh seam. They were from two to twenty acres each "and a great quantity of Limestone and stone coal." Pittsburgh Gazette, Aug. 9, Sept. 6, Sept. 27, Oct. 4, 1811; The Commonwealth, Aug. 19, 1811: Five tracts were advertised that contained coal. One had "fine springs and an inexhaustible mine of coal;" one, "excellent sugar camps, coal banks and limestone and a good mill seat;" one, "good sugar camps, an excellent coal bank and an elegant seat for a distillery;" another, a tract of 45,000 acres in Allegheny and Butler Counties affording "stone coal and iron ore, and seats for water works;" and the last a tract on Beck&apos;s Run, four miles from Pittsburgh "and a coal pit opened about one fourth of a mile from the river." The Mercury, Pittsburgh, April 8, Jan. 14, Feb. 11, 1813; Pittsburgh Gazette, April 16, Dec. 3, 1813: These tracts were advertised during the year in the vicinity of the city. One had "a good sugar camp, woodland and plenty of coal;" another, "a sugar camp and a coal bank on the premises;" while the others were "well timbered or well watered and had excellent stone coal." The Mercury, Pittsburgh, Feb. 2, 1814: A farm was offered for sale on the headwaters of Robinson&apos;s Run, in Washington County, four miles from Burgettstown, containing 60 acres, "a young bearing orchard,... a coal bank and a good sugar camp." Genius of Liberty and Fayette Advertiser, Uniontown, Pa., March 2, 1814, carried an advertisement of a sale of lots in the new town of Perriopolis; "the quantity and quality of the clay, sand and salt licks, near the premises, together with the timber and abundance of .stone coals The town of Perriopolis was situated upon a . farm at one time belonging to Washington.

Jan 1, 1942

By W. P. Barba

IN THE early summer of 1917, it became evident that the then existing sources of supply of guns and gun forgings were totally inadequate for the enormous and rapidly growing requirements of the Ordnance Department of the Army, so arrangements were made with sixteen makers of other products to take up the manufacture of guns and gun forgings. Nine of these makers were required to produce their own steel from the raw materials and convert it into rough machined gun forgings; the others finished and assembled these forgings into completed guns. In December, 1914, four of these makers of steel and rough gun forgings were instructed to manufacture the same amount of the 6-in. and 9.5-in. guns and howitzers. It, therefore, seemed practical .and profitable to assemble these makers into a small group, together with the officers of the Ordnance Department, and provide standard &apos;equipment in each of the four works for the production of these two types of guns. The advantages of this cooperation were immediately manifested, and there commenced an interchange of shop practice and a free discussion of facilities and methods that covered not only the equipment but the manufacturing processes.

Jan 1, 1920

By Paul L. Russell

THIS is a progress report of an experiment being undertaken in cooperation with the Bethlehem Steel Corp., the Crucible Steel Co., and the Rock Bit Sales and Service Co., involving heat treatment of the shank ends of drill steel. This experiment is being conducted by the U. S. Bureau of Mines in its experimental mine, Mining Research Branch, Bluemont, Va. The purpose of the experiment is to determine the effect of an increase in the time the steel soaks in the furnace during the hardening heat. It has been thought that increasing this time produces a soft zone below the lugs resulting in a metallurgical notch that causes early failure. Each of the steel companies furnished enough 11/4 - in. straight carbon, hollow, round steel to make up 10 sets of drill steel, in each instance the steel bars were from the same heat. These sets of drill steel, consisting of 2-ft, 4-ft, 6-ft, and 8-ft lengths were fabricated by the Rock Bit Sales and Service Co. Special attention was given to the forging of the steel to produce the best rods possible. The heat treatment of all thread ends was identical and followed the best practice. The heat treatment of the shank ends of five sets of steel from each company produced a soft zone 2 to 4 in. in front of the lugs. It was decided that possibly the best way to obtain this effect was not to overlap the hardening heat but to let the steel soak for an additional 30 min before quenching. Therefore the only variable in the test steels is the length of time the shank ends were in the furnace. The remaining drill steel shanks were treated as follows: Heat treatment in pyrometer-controlled furnace at 1550°F. Quenching oil at 105°F to 125°F temperature. Areas for heat treatment were; shanks, 11 in.; threads, 9 in. Time at heat, standard practice, 20 min for 11/4-in. steel. Actual drilling tests were made in greenstone, (a metamorphosed basaltic rock), and in epidosite. Greenstone has a specific gravity of 2.96 and a compressive strength of 44,200 psi. Epidosite has a specific gravity of 3.26 and a compressive strength of 63,100 psi. All drilling tests were made using a 31/2-in. column-mounted, automatic feed drifter, with a controlled air pressure of 90 psi at the throttle. Tungsten-carbide bits of 2 in. diameter were used for all drilling. Contrary to expectations the drill steels that were allowed to soak for the additional 30 min before quenching performed better than the steels that were heat treated according to standard practice. This performance, as shown in Table I, was especially noticeable in the drilling of epidosite. The "longheat" drill steels furnished by Company "A" drilled 154 pct more minutes than the "standard-heat" steel. Expressed in feet, the "long-heat" steel drilled 114.60 ft more before failure than the "standard-heat" steel. The "long-heat" steel furnished by Company "B" drilled 37 pet more minutes or 60.39 ft more before failure than the "standard-heat" drill steel. The effect of the long heat treatment was not as evident when the steels were drilling in greenstone (Table II). In greenstone, the increase in minutes drilled by the "long-heat" steel over the "standard-heat" steel was 47 pet and 1 pet, respectively, for Companies "A" and "B."

Jan 1, 1952

By Northcutt Ely

This chapter deals with the systems of laws by which governments regulate the exploration for and production of the minerals within their jurisdictions. It is a summary, restricted by necessary space limitations, of material assembled by the author for a publication of the United States Bureau of Mines, "Summary of Mining and Petroleum Laws of the World," (Information Circular 80 1 7, 196 1. ) The present study is organized in three parts, dealing with (1) the historical background of these legal systems, (2) laws of the United States, and (3) laws of other countries of the world. The reader&apos;s attention is invited to the acknowledgments at the end of the chapter, which inadequately express the appreciation due those who have assisted in the collection of this material. Part I. Historical Development of Major Western Systems of Land Tenancy with Respect to the Ownership and Control of Minerals The use of metals in primitive societies was largely confined to the manufacture of weapons for self-preservation. The ruler&apos;s control over copper, then bronze, then iron, was essential to maintenance of his own ascendancy at home and his group&apos;s position against neighbors who had access to similar metals. Ancient societies were thus characterized by the ruling group&apos;s ownership of minerals and metals. The Egyptian civilization, which emerged in the fourth millenium B.C. upon the agricultural subjugation of the lower valley of the Nile, was responsible for extensive development of the upper valley as a source of mineral wealth. The production of gold during the height of that civilization has been estimated at $30,000,000 per year, thus equaling the early placers of California and Australia. The mines of Egypt were the property of the Pharaohs and were controlled at their direction. Greek mining developed a different scheme of land tenancy which more closely resembled modem concepts. Development of mineral resources was

Jan 1, 1964

By C. S. Roberts

THE advent of a sensitive X-ray method of analysis recently has allowed the determination of retained austenite in amounts as low as 0.3 pct.&apos; As a result this phase has been found in quenched low carbon steels where its presence has not been generally suspected. In the course of a study of the tempering process,&apos; retained austenite determinations were made by the X-ray method on a series of high purity Fe-C alloys and plain carbon steels. The chemical analyses of these materials and details of the hardening procedure are given in Table I. Results were obtained after quenching to 72°F (22°C) and — 321 °F (—196°C). Austenitizing temperatures were between 100" and 150°F above A, or Acm. All proeutec-toid cementite or ferrite was in solution. The combination of the results with those of Averbach, Castleman, and Cohen,&apos; and earlier results of Esser

Jan 1, 1954

By G. V. Sullivan, B. E. Davis, T. O. Llewellyn

The Bureau of Mines, US Department of the Interior, conducted studies to recover phosphate from four dolomitic southern Florida deposits not currently mined. The samples contained 5.8-10.2% P205 and 1.7-4.8% MgO. Chemical analyses of sized fractions indicated that no pebble concentrate, +1.2 mm (+14 mesh) could be produced from these samples. A scheme was developed that consisted of desliming, grinding, scrubbing, and redesliming the ore to produce a flotation feed. Conventional one-step fatty acid fuel oil batch flotation tests on the samples resulted in concentrates containing 29.0-31.3% P205 at flotation recoveries ranging from 72.4 to 96.1% of the flotation feed. The MgO content of the concentrates ranged from 0.47 to 1.36%. Continuous flotation of the Manatee No. 2 sample indicated that commercial-grade phosphate concentrates analyzing 31.3% P205 and 0.55% MgO could be produced with a flotation recovery of 89.9%. The MgO content of concentrates obtained from the Manatee No. 1 and Hardee samples was 1.20 -1.36 %, respectively. Leaching with aqueous SO2 reduced the MgO content of these phosphate concentrates to 0.5 and 0.8%, but with a concomitant loss in phosphate recovery of about 10%.

Jan 1, 1985

By AIME AIME

THE petroleum engineers have the conference habit. They drop in, thresh things over, and drop out. No time is wasted. So it was at the Fort Worth meeting of the Petroleum Division, Thursday and Friday, Oct. 8 and 9; headquarters, Blackstone Hotel. Associate Chairman Albertson arrived the morning of the 7th, to tie in any loose ends of the technical program. S. M. Greenidge, chairman of the local committee, checked the arrangements with his committeemen at a luncheon that noon. By mid-afternoon the next day&apos;s attendance was anybody&apos;s guess-there were no noses to count. But when the gavel sounded Thursday morning 175 members and guests were present, also the official A.I.M.E. party consisting of President Lovejoy, Secretary Parsons, and George Otis Smith. Shortly after adjournment Friday afternoon all but a handful had vamoosed, lit out, disap¬peared. But, in the meantime, it was a grand conference, attendance maximum every session, and the discussion fast and furious. The discussion came from all over the floor, sometimes as good-natured sniping, sometimes in long volleys that were almost fatal to the reporter. Everyone knew his subject and few there were who had nothing to say.

Jan 1, 1936