Search Documents

By J. E. Burke, C. W. Mason

In attempting to study precipitation from a tetragonal lattice, using solid solutione of bismuth in tin, it was found that although a Widmanstätten pattern is observed1,4 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process. Microscopical Studies Alloys were made from Chempur tin (Standard samples 42b and 426, National Bureau of Standards), and bismuth (Kahl-baum C.P.) by melting weighed quantities together under palm oil, stirring well, and castilig in a heated graphite mold. The polishing and etching techniques employed largely govern the visibility of the structural changes. The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through Behr-Manning 3/0 abrasive papers, lubricated by a solution of paraffin in kerosene. A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution; repeated etching and polishing served to remove disturbed metal. For high-power examination better preparation was necessary. It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching. Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use. A better procedure was as follows: The metal lap was warmed slightly, and a 4-in. circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin. The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C. was poured over it, allowed to stand for I to 2 min. and then washed off. It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample. The cloth was then charged with a paste of the relevigated alumina in water. Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet. The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deterioratcs after about 24 hr. This is not serious, because a new lap can be prepared in about 5 min., and only small pieces of cloth are used. Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer. For the final etching, the most satisfactory reagent was that of Tafls,7 the formula for which is: FeC13.6H2O, 2 grams; HC1, 5 c.c.; H2O, 30 c.c.; C2H5OH (95 per cent), 60 C.C. This etchant reveals differences in com-

Jan 1, 1942

By J. E. Burke, C. W. Mason

In attempting to study precipitation from a tetragonal lattice, using solid solutione of bismuth in tin, it was found that although a Widmanstätten pattern is observed1,4 only a qualitative analysis of the orientation relationships is possible, because of the unusual structural changes that accompany the precipitation process. Microscopical Studies Alloys were made from Chempur tin (Standard samples 42b and 426, National Bureau of Standards), and bismuth (Kahl-baum C.P.) by melting weighed quantities together under palm oil, stirring well, and castilig in a heated graphite mold. The polishing and etching techniques employed largely govern the visibility of the structural changes. The preliminary surfacing operations were similar to those recommended by Villela and Bergekoff,5 through Behr-Manning 3/0 abrasive papers, lubricated by a solution of paraffin in kerosene. A rough metallographic polish was next given, using a thin cotton cloth charged with relevigated alumina (maximum particle size of about 4µ) and soap solution; repeated etching and polishing served to remove disturbed metal. For high-power examination better preparation was necessary. It was found that on such soft metals the threads of the fabric, rather than the abrasive, cause most of the scratching. Cotton outing flannel, which had been brushed so that the nap lay down, was fairly satisfactory, but a heavy grade of silk velvet (not the noncrushable kind) was found to be better, especially after some use. A better procedure was as follows: The metal lap was warmed slightly, and a 4-in. circle of woolen broadcloth was cemented to its center by a thin film of melted paraffin. The broadcloth was then moistened with water, and a 30 to 40 per cent solution of sodium hydroxide heated to about 50°C. was poured over it, allowed to stand for I to 2 min. and then washed off. It was neither necessary nor desirable to remove all the sodium hydroxide from the cloth, since its etching action aided in the removal of the flowed layer from the sample. The cloth was then charged with a paste of the relevigated alumina in water. Since this lap did not remove deep scratches, it was necessary previously to polish the specimen on some material such as the silk velvet. The sodium hydroxide softens and partly gelatinizes the woolen lap covering, permitting a scratch-free polish, but its action continues, and the cloth deterioratcs after about 24 hr. This is not serious, because a new lap can be prepared in about 5 min., and only small pieces of cloth are used. Etching with a strongly acid solution of ferric chloride was found satisfactory for removing the flowed layer. For the final etching, the most satisfactory reagent was that of Tafls,7 the formula for which is: FeC13.6H2O, 2 grams; HC1, 5 c.c.; H2O, 30 c.c.; C2H5OH (95 per cent), 60 C.C. This etchant reveals differences in com-

Jan 1, 1942

By J. W. Downey, M. V. Nevitt

DURING the course of the present investigation of alloy phases involving transition metals, phases were found in the systems Os-Ta, Os-W, and Ir-Ta. The (Os, W) phase was also recently reported by Raub.1 Pertinent information is given in Table 1. The approximate composition range of sta- bility was determined metallographically on arc-melted buttons that were annealed 72 hr at 1200°C and water quenched. X-ray powder patterns were obtained with a 114.6 mm diam powder camera using filtered copper radiation. The composition for (Os, W) given by Raub (66 atomic pct W) is in agreement with the composition range reported here. However, the lattice constants reported by Raub are: a0= 9.913±0.007, c/a= 0.515. The reason for the discrepancy between the lattice constants reported by Raub and those given here is not known. Acknowledgments The authors wish to thank M. H. Mueller and H. W. Knott for assistance with the X-ray diffraction work, and R. A. Morris for the preparation of the alloys. This paper is based upon work performed at the Argonne National Laboratory under the auspices of the Atomic Energy Commission.

Jan 1, 1958

By C. WIFLARD HAYES

(New Haven Meeting, February, 1909.) I DESIRE to make it perfectly clear at the outset that I fully realize the hazardous nature of any attempt to estimate the quantity of iron-ore or any other mineral in the ground. I should not have had the temerity to venture upon an inventory of the iron-ore supplies of the United States except for the requirements of the Conservation Commission. During the preparation of this inventory I have been impressed by the wide diversity in estimates of those best qualified to. hold an opinion, and I am therefore prepared in advance for criticism of my figures. Inasmuch as this report was prepared in large part for unprofessional readers, I considered it necessary to classify and describe the commercial iron-ores in a somewhat elementary manner, in order to explain the reasons for the large element of uncertainty in the estimates. I have therefore given a chemical and a geological classification of iron-ores, which place the commercial deposits in six classes: (1) magmatic segregations in basic igneous rocks; (2) contact-deposits formed in connection with igneous intrusions; (3) concentration-deposits; (4) replacement-deposits; (5) bedded-deposits, and (6) gossan-deposits. The iron-ores are further distinguished under two classes available and not available. This classification is in large measure arbitrary, and it, is evident that it will vary front time to time. In the available class are placed those ores which can be worked at a profit under conditions essentially as they exist at present. Since it depends wholly on the question of costs, the various factors which affect cost will determine the classification of any particular deposit. Actual production, * Abstract of Report prepared for the Conservation Commission. t Chief Geologist, United States Geological Survey. .

Apr 1, 1909

By AIME AIME

FEW indeed are the sections of the country where trained or partly trained workers have not already been hired by a war industry plant or will be within the near future. Yet right in the midst of the heavily industrialized East lies the anthracite area, home of a million people, whose productive power has persistently been by-passed either by private industry or by the Government Plant Site Board. The chief reason given for not locating war plants in the area is that it is not within the strategic zone, but in numerous instances elsewhere this rule has been waived. Furthermore, the anthracite region is well protected on all sides by mountains and is at all points more than 100 miles inland. Continued depression in the anthracite industry and a crippling blow dealt by the war emergency to the production of silk and rayon goods, the chief manufacturing activity of the area, have resulted in a heavy migration, particularly of trained young workers, into near-by industrial areas. At least 50,000 people are currently unemployed, with the likelihood of an increase in coming months, and as many families are on relief.

Jan 1, 1942

By R. W. Coughlin, W. U. Ault

Experiments in laboratory and mine have clearly demonstrated the usefulness of radioactivity detection for directly measuring the potassium content of potash ore as mined. This paper presents the results of these tests and documents the design of a system for automatically grading and sorting potash ore on the basis of radiation detection. It is shown how the experimental results in the subject mine lead directly to the design of this kind of an automatic control system. The system is capable of grading the ore with an accuracy of approximately ±2% K20 content or better. Due to the usual stratification of the ore body, mining potash seldom presents an extreme problem of gangue separation. Nevertheless, it is frequently necessary to transport within a potash mine and even hoist to the surface considerable quantities of halite and other valueless materials. Up to recent times it has been customary to recognize and route these materials by simple visual and manual techniques. However, the work reported here clearly demonstrates that it is now practical and economical to improve upon these techniques by continuous measurement1 of the naturally occurring radioactive isotope, potassium-40. It was the purpose of the work reported here to investigate this technique and assess its applicability. LOCALE OF EXPERIMENTS The work described here was carried out in a potash mine in Carlsbad, N.M. At the working face of this mine the potash ore is freed by blasting; it is then transported a short distance by shuttle car to a moving-belt system which conveys it to the main shaft where it is hoisted to the surface. Quantities of gangue which are also produced in the mining operation are disposed of in mined-out sections of the mine where possible. Otherwise, this material which contains only a small percentage of potassium (as K2O) must also be transported by the conveyor-belt system to the main shaft and then hoisted to the surface and discarded. With this situation, any measuring device for automatic control purposes must be capable of clearly distinguishing between gangue containing insignificant amounts of K2O and ore containing larger percentages of the same mineral. The conveyor-belt system transports the material from the mine face to a rotary crusher and then to temporary storage pits at the main shaft. This is shown in Fig. 1. Upon leaving the conveyor belt the material enters either one of the two storage pits according to the position of a manually operated gate. It was decided that all experiments should be carried out at the conveyor belt between the crusher and gate with a view to the possibility of providing a signal which could operate the gate automatically. THEORETICAL BASIS AND LABORATORY EXPERIMENTS In principle it is possible to grade potassium-bearing ore on the basis of radioactivity. Natural potassium contains 0.012% K40, which is radioactive with a half-life of 1.3 x 10' years. Although about 89% of the K40 disintegrates to Ca40 by beta decay, the other 11% changes to Ar40 by electron capture and the emission of gamma rays. Unlike the ß-rays which are readily absorbed in the first few millimeters of ore surrounding the disintegrating nucleus, the y-ray photons will escape from an ore sample several inches in size. A detector rigidly mounted under a conveyor belt loaded with potash ore will intercept some constant fraction of all the photons emitted from the ore within its field of view. Under these

Jan 1, 1968

By Frederic Brunton

I. INTRODUCTION THE smelting plant of the British Columbia Copper Co. at Greenwood, B. C., now closed because of the decline in the price of copper due to the European war, is of special interest to metallurgists for several reasons. It was successfully smelting in blast furnaces the lowest grade copper ore of all plants in America. In order to do so, it had to run at' very high efficiency, which necessarily required a large tonnage per square foot of hearth area, together with the minimum amount of labor and other costs. The furnaces smelted daily 2,250 tons of ore (6.62 tons per sq. ft. of hearth area), carrying 0.85 per cent. of copper, at a smelting cost of $1.18 per ton. The entire plant required 130 men to operate it and keep up repairs, showing a labor efficiency of about 17.5 tons per man per day. In the present paper, the method of obtaining these results is shown. Most of the information contained in this description I obtained as Assistant Superintendent, during the two years preceding the present shutdown. Other sources of information to which I am indebted are: The British Columbia Copper Co., Ltd., by Alfred W. G. Wilson, in The Copper Smelting Industry of Canada; Greenwood Smelting Works, by J. E. McAllister, Engineering and Mining Journal, vol. xci, pp. 1011 to 1015 (May 20, 1911); and Description of the Copper Smelter of The British Columbia Copper Co., by W. L. Bell, in Transactions of the Canadian Mining Institute, vol. xvi, pp. 151 to 154 (1913).

Jan 7, 1915

By Peter R. Drummond

THE final casting of refined copper has been re-J- stricted for generations by the following sequence of operations: Filling the reverberatory furnace, melting, skimming, blowing or flapping, and poling. The hoped-for 24 hr cycle, producing 300 tons or more, has been taken up largely with the necessary bat time-consuming tasks of cleaning the bath, sulphur elimination, and in turn removal of excess oxygen to produce tough-pitch copper. Incidental to comparatively slow melting under combustion gases, copper oxides react with the furnace lining, and the slag so-formed must be completely recycled. The three-phase arc furnace has eliminated some of the cycle stages, and telescoped the remainder into a continuous operation. Electrical energy, supplied to graphite electrodes enclosed in high grade refractories, rapidly melts copper cathodes and sustains a stream of metal, containing approximately 0.01 pct oxygen, without contamination from fuel. The arc was struck on the first large electric furnace for melting copper in the United States on April 13, 1949. The earliest use of this type of furnace was at Copper Cliff, Ont., in 1936, and an admirable description of their installation has been published? Copper, melted in the Baltimore furnace, is used to cast billets, and the installation differs somewhat from the Canadian, as will be described. The arc furnace is a heavy-duty, three-phase furnace, holding 50 tons, the general outline of which appears on Fig. 1. The steel shell is 15 ft ID with a bottom radius of 14 ft 2 in. The roof, separate and distinct from the body, consists of a 15-ft water-cooled, cast-steel ring of the same outside diameter as the furnace. The center line of the furnace lies 9 ft 6 in. from that of the trunnions, permitting a 5" backward tilt for skimming, and a 40" maximum nose tilt forward for complete draining. Normally, the furnace overflows by displacement, and the use of the forward tilt arrangement is restricted to covering charging delays. The charging slot, 3 ft 8 in. x 5 in., lies on the north center line, the tap hole on the south, and the 30x30 in. skim door 45" to the west of the slot. The original 20-in. graphite electrodes were replaced with 14 in. in December 1949. Three conventional direct current winch drives, governed by electrical controls, position each electrode which has individual mast supports and counterweights. An independent circulation supplies cooling water for the electrode glands, the roof ring, charge slot, and the skim door frame. Arc Furnace Refractories Hearth: Fused-in monolithic bottoms had been used in copper arc furnaces, installed prior to April 1949. These consisted of thin layers of periclase, successively fused in place over preliminary brick courses. Heat was obtained from the arc, using a T-like arrangement of broken electrodes resting directly on the periclase to be fused. The operation, taking weeks to perform, was very expensive. The chemically-bonded magnesite-brick bottom, installed at Baltimore, was the first of its kind and a radical departure from previous practice. It consists of a 1 to 6-in. layer of castable refractory laid on the steel shell, modifying it to a 12 ft 2 in. bottom radius. Two courses of 9x2 % -in. fireclay straights and keys follow. The third course is made of 9-in. magnesite blocks of special shape to form circles of an inverted arch. It was started by a four piece keystone with skew-backs forming the outer course. The fourth course also started on a central keystone, or button, of four 90" segments, 12 in. diam x 13 Vz in. deep, and continued with 13%-in. blocks. Skewbacks at the shell completed the course to produce a horizontal surface for the side walls with a single course of No. 2 arch fireclay against the steel. Dry chrome-magnesite cement was brushed over each course after laying, and a 1-in. expansion space between the brick and the shell was filled with the same mixture. The total bottom thickness, excluding the castable material, was 5 in. of clay plus 22% in. of chemically-bonded magnesite. Tap Hole: A 5-in. OD and 3-in. ID silicon-carbide tube constitutes the tap hole and is set tangential to the upper course of the furnace bottom. Molten metal fills the tube when the furnace is level and filled to capacity. Side Walls: The lining, against the shell, consists of a 9x4Y2x3 in. soldier course of fireclay, using straights and No. 1 arches to turn the circles. A second soldier course of 9x4'/2x2'/2-in. fireclay was laid in a somewhat similar fashion. Three courses of 13Y2x6x3 in. and 9x6~3 in. of final magnesite, laid flat, completed the lining, using Nos. 1 and 2 keys to turn the circles. Cardboard spacers were placed between every two bricks in horizontal courses, and a thin coat of chrome-magnesite cement filled the joints between the firebrick and magnesite. A sprung-arch spanned the skim door with jambs of suitable magnesite shapes. Charge Slot: The slot is 3 ft 8 in. wide x 5 in. high. A silicon-carbide sill of special shapes has a 30" slope to allow cathodes to slide easily into the bath. The original arch was flat, and composed of Nos. 1 and 2 wedge magnesite with a 6-ft radius. It projected 5 in. over the sill, and, being a flat arch, gave an 18 15/16-in. opening between the inner edge and the metal line. The whole assembly was later raised 9 in., and the flat arch replaced with an arch, the lower edge of which maintained the 5-in, width from the outer to inner edges as shown in Fig. 2. A water-cooled, cast-copper jacket protects the steel shell behind the slot.

Jan 1, 1952

By Leonid V. Azároff, H. N. Murty

In the course of investigating the soft X-ray absorption spectra of Ni-A1 alloys, Das and ~zfiroff' observed an anomalous brittleness in solid solutions containing 3 to 5 at. pct Al. The brittle alloys also had anomalously larger lattice constants' and the fine structure at the nickel K edge of an alloy containing 3.96 at. pct A1 unexpectedly resembled that of NiA1 more closely than that of a solid solution containing 5.51 at. pct Al. This led them to suggest the possibility that short-range ordering was produced during the homogenization anneal to which each specimen was subjected, similar to that observed in dilute solutions of vanadium and of chromium in nickel: as the principal cause of embrittlement. It was decided to repeat the above measurements on several alloys in this composition range in order to test the above hypothesis and to establish the effect of heat treatment on the alloys' properties. Three solid solutions in this range were prepared containing, respectively, 3.16, 4.00, and 4.54 at. pct Al, in addition to alloys containing 6 and 9 pct. All samples were annealed in vacuum at 1800°F for 100 hr and then furnace-cooled to room temperature, as in the original study. The lattice constants of these alloys are shown by open circles in Fig. 1 and can be seen to fit quite closely the curve established by the previously measured values, indicated by solid circles. (The experimental errors are of the order of the size of the circles, +o.oo~R.) The three alloys containing 3 to 5 at. pct A1 were found to be quite brittle, as previously reported. In order to test the possibility of ordering, these three solid solutions were again heated to 1800°F and, following a few hours at that temperature, were quenched directly to room temperature. All three alloys lost their brittleness. In order to verify the proposed ordering hypothesis, it was decided to subject each sample to several cycles of quenching and annealing (disordering and ordering). After some experimentation, it was established that reproducible results could be obtained by anneal-

Jan 1, 1968

By Paul M. Tyler

THE winning of metals from Nature has been advanced to a degree of efficiency that commands admiration even in this Machine Age. Economy of human effort underground, in surface plants, and in treatment works, and better means of performing all manner of operations have cut costs and im¬proved products to an extent that seems far beyond the wildest imagin¬ings of those that labored in the days of hand mining and muscular metallurgy. Principles and methods borrowed from other professions and sciences - mechanical engineering, chemistry, and physics-all have con¬tributed to the rapid development of ore production and treatment, but no small part of the achievements must be credited to the free exchange of ideas within the industry itself and mass attack upon problems of mutual concern. The esprit de corps or class consciousness that has contributed so effectively to the progress of the metal industries has been less apparent among nonmetallic mineral producers. As a class they have been handicapped by inadequate contact with the metal-mining fraternity as well as among themselves.

Jan 1, 1935

By T. Yamasaki, S. Usu

Adsorption of potassium dodecyl xanthate from aqueous solutions on artificial and natural zinc sul-fides was studied by means of infrared absorption spectroscopy. The adsorption species and their stabilities varied depending upon the conditions of the surfaces of the zinc sulfides. Adsorption products were analyzed after they had been removed from the surface with pyridine. Zinc dodecyl xanthate was confirmed for surfaces covered with oxidized products while dodecyl alcohol and carbon disulfide were detected on purified or weakly oxidized surfaces. It is of great significance to study the adsorbed species of collectors on the surface of sulfide minerals with a view of increasing our understanding of the mechanism of flotation. Compared with other methods, infrared spectroscopy promises to be of particular value in determining the nature of the species adsorbed at the mineral/solution interface since it gives direct identification of the adsorption products; and, furthermore, it has an advantage over the electron diffraction technique which has been employed in similar problems in that infrared spectroscopy utilizes radiation of very low energy so that the probability of changing the unstable surface films during examination should be correspondingly decreased. Infrared spectroscopic studies concerned with sulfide mineral flotation have already been reported by several investigators on zinc sulfide-hexanthi01' and lead sulfide-xanthate2,3 systems. The purpose of the present study was to investigate the adsorption of potassium dodecyl xanthate (KDX) at the zinc sulfide-aqueous solution interface by means of infrared spectroscopy. Rarely is the pure zinc sulfide-xanthate system encountered in practical flotation since zinc sulfide is usually activated with small amounts of certain metallic ions, such as copper ion. However, investigation of the pure zinc sulfide-xanthate system appeared promising for studying the fundamental mechanism of the adsorption of xanthate on the sulfide minerals. Although there are few cases where xanthates having an alkyl radical higher than hexyl are employed in practical operations, KDX was used in this study since it was reported that the adsorbability of xanthate on zinc sulfide was increased with an increasing number of carbon atoms of the alkyl radicals.4 EXPERIMENTAL Samples: Experiments were made on artificial zinc sulfide and natural sphalerite. The artificial zinc sulfide was obtained commercially from Dainihon Toryo Co. as a fluorescent pigment of the purest grade A. Considering the fact that there are often cases where the surface of sulfide minerals are apt to be oxidized so that the adsorption of xanthate at sulfide mineral/solution interfaces may be substantially affected, two different procedures were employed in preparing the samples of the artificial zinc sulfide. 1) The zinc sulfide was washed with hot concentrated ammonium chloride solution (300 g per liter) to remove surface oxidation products and followed by washing with deoxygenated hot distilled water by centrifugation until the constant electric conductivity of the solution was reached (Sample I) (specific conductivity of the solution = 8.6 x l0-5 ohm-' cm-'). 2) Sample I in a suspension of 5% by weight was oxidized with a 1.5% aqueous hydrogen peroxide solution for about one hour, and then was washed with distilled water as mentioned in the preparation of Sample I (Sample 11) (specific conductivity of the solution = 1.0 x 10"4 ohm-' cm-'). Both Samples I and II were dried under vacuum and stored in a vacuum desiccator. The specific surface areas of the samples determined by the BET method using carbon dioxide gas were 19 x l04 cm2 per g for Sample I and 35 x l04 cm2 per g for Sample 11. In addition, a sample which was derived from Sample I was also prepared. In 40 ml of 3 x 10-2 M zinc sulfate solution was placed 2 g of Sample I for 2 hours, washed with distilled water by successive centrifugation until no sulfate ion could be detected and dried under vacuum (Sample 111). The purpose of this treatment will be described later. Natural sphalerite was carefully selected by hand, ground in a mechanical agate mortar for about 40

Jan 1, 1965

By Rustum Roy, E. F. Osborn

THE investigation discussed in this paper concerns phase equilibria in the alumina-silica-water system. Studies in this system are part of a re¬search project sponsored by the Geophysics Branch of the Office of Naval Research2 directed toward increasing knowledge of the stability relations of metamorphic mineral assemblages. Inasmuch as metamorphic rocks consist largely of aluminosilicate struc¬tures, many of them hydrated, the system alumina-silica-water is a logical starting point for the systematic laboratory study of metamorphic mineral systems. Although logical, this is not, however, an easy approach to the problem because of the very great difficulty of obtaining transformations among structures in response to changes in temperature, pressure, and con¬centration. Commonly equilibrium among the phases in this system is exceed¬ingly difficult to attain. New laboratory techniques are required to produce certain structural rearrangements, such as inversion of diaspore to boehmite or the transformation of alumina-silica mixtures to andalusite or kyanite. Phase equilibrium data for the alumina-silica-water system are consequently only partly complete, and only a summary progress report is presented here. Crystalline phases in the alumina-silica-water system are numerous and many are common minerals. The oxide components exist as: quartz, tridymite, cristobalite, corundum, water, and ice. Binary compounds occurring naturally are: sillimanite, andalusite, kyanite, and mullite in the alumina-silica system and gibbsite, boehmite, and diaspore in the alumina-water system. The most abundant among the ternary compounds is the composition A12O3.2SiO2.¬2H2O, existing in the four structural modifications, kaolinite, nacrite, dickite, and halloysite. The hydrated form of halloysite, A12O3.2SiO2.4H2O, is here called endellite. Pyrophyllite, A12O3.4SiO2.H2O, is the third ternary compound of natural occurrence. In addition to these minerals, two other ternary crystalline phases have been encountered in this study. The first is a structure resembling montmorillonite and corresponding perhaps to the pure aluminian end member of the beidellite series. The other has a composition approximating A12O3.2SiO2.H2O but its composition and structure are still in doubt. LABORATORY PROCEDURE In these laboratory studies, a starting material such as an alumina-silica gel or one or more of the crystalline phases is wrapped in platinum foil,

Jan 1, 1952

By John F. Elliott

STAFF: Editor, Gerhard Derge Acting Editor, Poul G. Shewmon Carnegie lnstitute of Technology Schenley Pork Pittsburgh 13, PO. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Rich-ard C. Cole, President; Karl L. Fetters, Past-President; J. H. Scoff, Vice President; R. L. Henneboch, Treasurer, R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairmon; T. E. Dancy, P. R. Gouwens, W. A. Krivsky, F. C. Longenberg, E. R. Morgan, R.R. Nosh, Poul Queneou, W.O. Philbrook, J. H. Scoff, L. L. Seigle, and M. E. Wadsworth. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extractive Metallurgy Division: M. E. Wadsworth, Chairmon; R. E. Grace, Vice Chairman; D. H. Baker, Jr., G. M. Bell, D. H. Bridges, J. M. Cigon, G. W. Healy, R. A. Lewis, C. E. O'Neill, A. W. Schlechten, R. E. Shinkoskey, and W. W. Stephens. Iron and Steel Division: T. E. Dancy, Chairman; A. Muan, D.W. Murphy, R. D. Pehlke, J. M. Uys, J. 5. Wagstoff, and R. G. Word. lnstitute of Metals Division: R. R. Nash, Chairman, H. H. Johnson, Jr., Vice Chairman; M. R. Achter, P. A. Beck, J. J. Becker, G. F. Bolling, J. 0. Brittain, J. 8. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. A. Girifalco, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, R. H. Richmao, H.C.Rogers, W. Rostoker, 0. D. Sherby. E. A. Steigawald, R. Steinitz, H. C. Stumpf, R. A. Swalin, W. A. Tiller, W. R. Upthegrove, D. Walton, H.W. Weart, and D. Wilsdorf. Published bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc 345 East 47th Street, New York 17. N. Y. Telephone PLaza 2-6800. Subscription $30 per year for non-AIME members in United States and North, South, and Central America; $32, foreign;$30per $7 50 for AlME members. Single copies, $6.00, single copies foreign, $6.50. The AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1963 by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc....Registered cable address, AlME New York . .. Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts . . Second class postage paid ot New York, N. Y., and Ann Arbor, Mich. Volume 227, Number 4.

Jan 1, 1963

By John G. McLain

OF all the zinc that the world consumed in 1936-'38 the United States took about 31 per cent, and almost 14 per cent of the world's zinc supply in that period was used for galvanizing purposes in the United States. Further examination of the statistics shows that about 71/2 per cent (147,500 tons in 1939) of the world zinc consumption goes into the galvanizing of sheets in the United States, which is what I am going to talk about in this paper. There is nothing especially new about galvanizing; in every year since 1921 somewhere between 41 and 49 per cent of the country's zinc consumption has been used for this purpose, and yet few people not specialists in its manufacture know much about how it is made. You take an iron or steel sheet and dip it in molten zinc and there you have a galvanized sheet-that about epitomizes popular knowledge of the subject even among engineers.

Jan 1, 1941

By R. W. Heckel, H. P. Cheskis, A. Lawley, M. R. Pinnel

THERE are discrepancies reported in the literature regarding the micro and macro stress-strain behavior of metals and alloys. In particular, Young's modulus and micro yield measurements often show significant variations depending upon the techniques employed.'-" The purpose of this note is to correlate measurements made with four techniques and to indicate where some of these discrepancies might arise. Allied use of these techniques can provide a complete and consistent characterization of micro and macro stress-strain behavior (over the strain range of 10-9 to 10--2 in. in.-') from a minimum number of samples. Techniques. The techniques employed for measuring stress-strain behavior involved the use of a) linear differential transformers, b) SR-4 strain gages, c) longitudinal resonance waves, and d) X-ray diffraction. Specimen geometries and preparations are summarized in Table I for each technique. Differential Transformer and Strain Measurements. An Instron universal testing machine, modified with an alignment device, was used to apply the load via parallel-jaw grips. The signal from the load cell was applied to the Y scale of a Moseley X-Y recorder (sensitivity of 10 lb load per in. chart). The elongation was monitored simultaneously with strain gages mounted on three sides of the rectangular specimen, and with two linear variable differential transformers (LVDT) mounted at 90 deg to one another on faces that also contained the strain gages, Fig. 1. The signal from one of the LVDT's was applied to the X scale of the recorder (sensitivity 40 µ in. elongation per in. chart) in order to trace a continuous load-elonga-tion curve. Concurrently, the strain on the same face (i.e., the face monitored by the LVDT) was recorded by the corresponding strain gage. A stress-strain curve was plotted from the load cell-strain gage data and was compared to the stress-strain curve (converted from load-elongation) plotted from the continuous load cell-LVDT trace. Identical Table I. Description of Specimens Used in the Present Study Material Dimerisions Preparation Condition 99.99 pct A1 tensile 318 by 3/16 by 3 in. as cast ingot; cut annealed specimen on diamond wheel 2024 A1 tensile 318 by 3/20 by 31/2 in. vacuum hot annealed specimen pressed sheets; cut on diamond wheel 99.99 pct Al 3116 by 3/16 by 2 in. cut from tensile prestrained dynamic modulus specimen after 10"* in. specimen test per in. 2024 A1 dynamic 3/20 by 3/20 by 2 in. vacuum hot annealed modulus specimen pressed sheets; cut on diamond wheel 2024 A1 X-ray gage section 112 by vacuum hot annealed specimens 1/4by1/20in. pressed sheets; cut on diamond wheel

Jan 1, 1970

By A. E. WALKER

SOME eighty years have elapsed since the discovery of the Clifton magnetite deposit. For a few years about the time of the Civil War it was mined for iron ore. most of which was smelted on the property. Since risen the small exposures of ore in the old cut. test pits, and on the dumps have been examined by various prospectors. The M. A. Hanna Co. first became interested in the possibilities of the deposit when we discovered the large area of strong magnetic anomalies caused by the margnetite bed, indicating a size that would support a commercial operation. In 1940 we made a detailed magnetometer survey of the area. and the deposit was diamond-drilled. The main ore lied was found to be 1500 ft. long, to average 60 ft. thick, and to dip southeast at an angle of about 40 deg. The thickness of the bed is irregular in wavy folds both along the strike. and down the dip. Faults occur at both raids of the main deposit.

Jan 1, 1943

By Charles Macdonald

WROUGHT-IRON eye-bars for bridges and roofs, designed upon what is known as the pin connection system, have been successfully manufactured in this country for some years. The most approved methods employed have been the hydraulic upsetting process, and by die-forging under a hammer. In upset eyes the fibre of the iron is necessarily much distorted ; and in bars of considerable size, this disturbance seriously impairs the strength of the connection. Mr. Collingwood, in discussing my paper on "Proportions of the Heads of Eye-bars," read before the American Society of Civil Engineers, Jan. 21st, 1874, submitted sketches of certain bars intended for the anchorage of the East River bridge, which had been exposed to the action of sulphuric acid a sufficient length of time to thoroughly cleanse the surfaces, and expose the condition of the fibre. These sketches are here reproduced for the purpose of illustrating the effect of this methpd of manufacture. In Figs. 1, 2, and 3, it will be observed that the fibres at A, and E, have been folded back upon themselves and otherwise twisted and disturbed, in a manner not calculated to inspire confidence in the integrity of the connection. To compensate for this defect, a large excess of metal is thrown into the eye; but a method of manufacture which involves such a necessity, even although it be the one giving the best results thus far, all things being considered, is far from being perfect.

Jan 1, 1879

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By R. B. Snow

This paper describes a technique of polishing and etching specimens of open-hearth furnace slags or hearth aggregates for identification of the crystalline constituents —lime (CaO), tricalcium silicate (3CaO.SiO2), dicalcium silicate (2CaO.-SiO2), rnonticellite (CaO.MgO.SiO2), or forsterile (2MgO.SiO2), with especial em-phasis on the mineral merwinite (3CaO.-MgO.2SiO2). With proper standardization, this identification does not require the use of the petrographic microscope. The composition of basic open-hearth slags and furnace bottoms falls, almost without exception, within systems containing CaO, MgO, 'IFeO,,, MnO and SiOz, in which the number of basic molecules so greatly exceeds the orthosilicate ratio (two molecules of base to one of silica) that free basic oxides, and combinations between them such as alumi-nates or ferrites, are present in cooled specimens. Orthosilicates of (CaO + NgO) are the most common in such specimens, since in nearly all cases, except premelt slags, the molecular ratio of (CaO + MgO) to SiO, is more than 2 to I. When sufficient lime is available it combines with the silica to form dicalcium silicate (2Ca0.Si02), which contains little, if any, IvfgO, FeO or MnO in solid solution whereas the latter oxides combine to form the oxide solid solution known as periclase. If the lime present is insufficient to form dicalcium silicate (2Ca0.Si02) it combines with Mgo to form either merwillite or moIlticellite (SiOz); these minerals take little if any FeO or MnO into solid solution and the remaining MgO, FeO and hInO combine as periclase. This generalization seems to be valid for basic slags and furnace bottoms, since minerals such as Ca0.MnOSi02 and CaO.FeO.SiOz are found only in slags in which the lime-silica ratio is less than 2 and are not observed in 'pecimens from furnace bottoms. The identification of crystalline constituents in such materials, especially of fine crystals in the groundmass, is difficult under the petrographic microscope. They are often masked by their neighbors because of their small size in relation to the thickness of the thin section and because of the presence of Opaque Or colored constituents. The indices of refraction and the optical sign of the mineral are sometimes difficult to determine because of the small size or because Of twinning or of inclusions within the crystal. Moreover, the positive identification of merwinite (3Ca0.Mg0.2Si02) from its optical properties is usually difficult in the presence of dicalcium silicate (zCaO.SiO2). CaO, MgO, jCa0.Si02 and 2Ca0.SiOz in open-hearth 'lags have been identified for a number of years in the U.S. Steel Corporation Laboratory by the usual

Jan 1, 1948

By E. T. Turkdogan, L. J. Martonik, R. J. Fruehan

Electrochemical measuretnents of the solid oxide electrolyte galvanic cells CY-Cr2O3 I ZrO2 (CaO) 1 O (in Fe alloy) CY-Cr2O3 I Tho2 (Y2O3)I O en Fe alloy) have been made at 1600°C (2912°F) in order to test the Performance of such cells at liquid steel temperatures. The oxygen pvobe (cell) consists of a disk of ZrO2 (CaO) or Tho2 (Y2O3) electrolyte fused at one end of a silica tube filled with a mixture of Cr-Cr2O3 which is the reference electrode. Upon immersion in liquid steel, the electromotive force readings achieve a steady value within a few seconds, and remain steady for 30 win or more. The perforwzance of the probes has been tested using Fe-O, Fe-Si-O, Fe-Cr-O, Fe-V-O, and Fe-Al-O alloys; the oxygen contents of liquid steel derived from the measured electromotive forces are in satisfactory agreement with those determined by arulysis. Use of the probe in the deoxi-datiorz of steel, in laboratory experiments, is discussed. The results indicate that there is insignificant electronic conductivity in ZrO2(CuO) at oxygen activities down to those corresponding to 10 ppm in steel. At lower oxygen activities, probes tipped with ThOn (Y2O3) disks perform satisfactorily at oxygen activities down to 1 ppm O or less. THE key to the control of deoxidation of steel is a sensing device to measure rapidly the concentration of oxygen in liquid steel in the furnace, ladle or tun-dish at any desired stage of deoxidation. The analysis of the cast steel by the neutron-activation or vacuum-fusion method gives total oxygen as oxide and silicate inclusions. This analysis is important for guidance to steel cleanliness; however, such a postmortem is of little value in the control of deoxidation of liquid steel. At the General Meeting of the American Iron and Steel Institute in New York, 1968, Turkdogan and Fruehan' presented a paper on the preliminary results of the work done in this laboratory on rapid determination of oxygen in steel by an oxygen probe. Details of the work done in this laboratory leading to the development of a galvanic cell for the determination of oxygen in liquid steel, and the results of the tests made are given in this paper. It was through Wagner's contributions, since the early Thirties, to the physical chemistry of semiconductors in general that it ultimately became possible to construct galvanic cells for application at high temperatures. In 1957, Kiukkola and wagner2 successfully demonstrated the use of several solid electrolytes in measuring the free energies of several chemical reactions, in particular, the use of lime-stabilized zir-conia in high-temperature oxidation reactions. Starting 7 years later, a number of papers appeared in the technical literature3-' demonstrating possible applicability of galvanic cells for the determination of oxygen in liquid steel. In the earliest work, Japanese investigators3j4 experimented with various types of reference electrodes, e.g., graphite-saturated liquid iron at 1 atm CO or Ni-NiO mixtures; the results obtained, though promising, were not of sufficient accuracy. Except for the work of Baker and West,6 all other investigators5,7,8 showed that ZrO2(CaO) electrolyte could be used for this purpose. The main part of the galvanic cell used by Fischer and ~ckermann' and by schwerdtfeger7 (the latter work was done in this laboratory), consisted of a ZrO2(CaO) tube, -1 cm ID, closed at one end, with a platinum contact wire fixed mechanically inside the closed end. The tube was flushed with a gas of known oxygen partial pressure, e.g., air, CO-CO2 or H2-CO2 mixtures; gas along with the platinum lead wire served as the reference electrode. The oxygen contents derived from measured electromotive forces agreed reasonably well with the oxygen contents determined by vacuum-fusion analysis. It is evident from recent investigations that the electromotive force technique using a solid oxide electrolyte is fundamentally well suited for the determination of oxygen in liquid steel. However, it is equally clear that the cell arrangement of the type as commonly used is in need of considerable improvement, as it exhibits several shortcomings for industrial and even laboratory use. 1) Because of its size, the zirconia tube, though stabilized, has a poor resistance to thermal shock. 2) Fine pores and microcracks, which are invariably present in zirconia tubes, are detrimental to the satisfactory operation of the cell, particularly when gas reference electrodes are used. 3) Air or carbon dioxide reference electrodes give rise to high electromotive force readings; as a result, the determination of oxygen in steel becomes less accurate. For higher accuracy, the oxygen partial pressure of the reference electrode should be in the range similar to that of oxygen in steel. 4) Even in laboratory experiments, difficulties are experienced when flushing the tube with gases and maintaining the proper gas flow rate. Fischer and Ackermann,' who used air as the reference electrode, reported that when the flow rate was too low, furnace gases would leak into the electrolyte tube, therefore lowering the oxygen potential and measured electromotive force. The required flow rate in order to avoid leakage depended on the tightness of the electrolyte tube which varied with different tubes, thus making it difficult to predict in advance the required flow rate. However, if the flow rate is too high the inside wall of the electrolyte tube would be cooler than the wall

Jan 1, 1970