Search Documents

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By Dix, E. H.

THE percentage of manganese used in commercial aluminum alloys is small, and yet this element is an important addition to some very valuable alloys. When used alone with commercial aluminum containing iron and silicon as impurities, the usual percentage in wrought materials is from 1 to 1.5 per cent., whereas castings may contain as much as 2 per cent. An aluminum-manganese alloy containing nominally 1.25 per cent. manganese is much used in sheet form for the manufacture of cooking utensils and other articles requiring a little greater strength and hardness than could be obtained with commercially pure aluminum. It is also used for various purposes in the form of rods, tubes and pipes. The aluminum-manganese alloys, both wrought 'and cast, offer excellent resistance to many kinds of corrosion attack. The U. S. Naval Gun Factory uses an aluminum alloy containing from 1 to 2 per cent. each of copper and manganese, for both castings and forgings. Manganese is also used, up to about 1 per cent., as a minor alloying .element in several of the strong aluminum alloys of the duralumin type. It is felt that the role of this element when thus used has not been fully understood, but it is believed that the results obtained in this investigation will throw additional light on the subject. The earlier work on the system aluminum-manganese was general in nature, and no detailed investigations of the relations existent in the useful aluminum-rich alloys have been reported. Guilletl1in 1902 surveyed the system, and Hendrichs2 in 1908 published an equilibrium diagram which, although based on .few data, is often used in the literature. Fragmentary work has also been done by other investigators."

Jan 1, 1927

By Edwin S. Johanson, Ronald H. Wolk, Clarence A. Johnson, Harold H. Stotler, Katherine C. Hellwig

The H-Coal process, an ebullated bed reactor system for converting coal to liquid fuel, is described. Results from long-duration continuous flow bench-scale operations with Wyoming Wyodak, Arizona Black Mesa, and Utah Kaiparowits Plateau coals are presented. Economic data on the conversion of these coals to liquid products are given. The potentials of the H-Coal process in regard to coal from western producers is stressed.

Jan 1, 1974

By Charles Hardy

ACTIVATED alumina is an aluminous material which may be 1 classified chemically as a partially dehydrated aluminum trihydrate having a high porosity and a perma¬nent physical structure. In general, it may be employed effectively and economically for the complete removal of water vapor from gases and vapors; for the selective adsorption of certain as especially those of the higher boiling points, and as a catalyst or catalyst carrier. Other forms of alumna are available and may be employed similarly but not so effectively nor can reactivation be accomplished with uniformity over many cycles without deterioration. The adsorption-reactivation cycle of activated alumina can be repeated many times without any apparent depreciation ill

Jan 1, 1934

By Claus Guenter Goetzeil

(New York Meeting, February, 1937) The object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion Average Coefficient per Deg. C. over Range 20° to 200° C. Pure aluminum..................................... 24.6 X 10-6 Cast low-expansion Si-Cu-Ni-A1 piston alloy............ 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron.............. 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.40-1.0 Mn).................. 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si)....................... 12.8 X 10-6 Pure silver.......................................... 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render its use feasible in Germany as an emergency measure. The coefficients of linear expansion of several metals and ailoys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850" C. for the solidus of the silver alloy. Pure silver melts at about 961" C., so that the tolerable depression in the solidus is rather small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937

By Lauren A. Wright, A. E. J. Engel

Under the designations "industrial talc" and "soapstone" are included earth materials of widely different chemical and mineral compositions. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3(SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.18 Single grains or leaves of talc, however, seem to have variations in water content that range from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.20 Most of the industrial talcs produced in the United States do not approach the composition given above (see Table 1), but are essen- [ ]

Jan 1, 1960

By Ralph W. Marsden

The natural iron ores of the Lake Superior Region in the United States are being replaced by iron-ore concentrates produced from magnetite- or hematite-rich horizons in the Precambrian cherty iron formations. The production of natural ores will soon be less than one-half of the total ore shipped annually. The tonnage of natural ore produced will continue to decline until it is a minor percentage of the ore shipped. The natural ores include (1) soft ore, (2) hard ore, ( 3) conglomerate ore and ( 4) siliceous ore. The soft ores are the important ore type and are sometimes termed "Lake Superior type ore". These ores are in situ deposits of hematite and limonite formed by the leaching of silica and other gangue materials in the iron formations. The leaching is believed to have been done by downward moving surface waters. In deep ore deposits, generally over 1000 feet below the present surface, circulation and leaching action may have been assisted by hydrothermal activity. Hard ore deposits occur on the Vermilion and Marquette ranges where hematite or magnetite has replaced the silica (and possibly some silicates) in cherty iron formation. These ores commonly occur in structural situations favorable for the movement of hydrothermal waters. The ores are believed to be the result of hydrothermal action with iron, possibly from the iron formation, transported by hydrothermal waters to areas favorable for the replacement of silica by iron oxides. Certain stratigraphic horizons of the Lake Superior Precambrian cherty iron formations contain sufficient iron as magnetite or hematite, with a grain size and texture that will give adequate mineral liberation, to yield an ore-quality product after grinding and concentration. The magnetite-rich deposits are termed magnetite taconites. These ores occur on the Mesabi, Gogebic, and Marquette ranges. Magnetite taconite ores are unenriched cherty iron formation and are the result of the sedimentary deposition of the iron formation and the metamorphic history of the rock. The commercial quality hematite-rich iron formations in Michigan are termed jasper ores. The jasper ores are being mined on the Marquette and Menominee ranges. These ores are composed of specular or granular hematite associated with quartz and iron silicates. The jasper ores appear to be recrystallized iron formations in which iron, prior to recrystallization, occurred as hematite.

Jan 1, 1968

1-Iron and Steel JOHN A MATHEWS, Chairman Ralph H SWEETSER Vice-chairman WILLIAM CAMPBELL, Vice-chairman MAX ROESLER, Secretary Iron Ore CHARLES B MURRAY, Chairman R C ALLEN W O HOTCHKISS MAX ROESLER ERNEST F BURCHARD THOMAS T READ DWIGHT E WOODBRIDGE M M DUNCAN WILLIAM KELLY CARL ZAPFFE C T FAIRBAIRN CHARLES F RAND

Jan 1, 1923

By Robert S. Young

During the last quarter-century, exploration for metallic deposits in Maine has been sporadic with peaks generally coinciding with periods of high metal prices. Known cases of regional or semi-regional evaluations are few; most efforts have been local and usually intensive. On the basis of broad geologic groups, the State has been divided into five fundamental environments: ( 1) coastal metamorphic belt; (2) southern volcanic belt; (3) Silurian slate belt; ( 4) northern volcanic belt; and ( 5) Devonian slate belt. Although not restricted to these areas, exploration in recent years has been concentrated in the northern and southern volcanic belts. Notable examples of recent exploration activity, directed to sulfide minerals, include: ( 1) the Knox County nickel-copper-bearing ultramafic rocks; (2) the Harborside (Cape Rosier) copper-zinc deposit; (3) the Second Pond (Black Hawk) zinc-copper-lead-silver deposit; ( 4) the Big Hill-Barrett lead-zincsilver- copper-gold zones; (5) the Parmachenee copper-zinc belt; ( 6) the Moxie Lake nickeliferous peridotite; and (7) the Attean quartzmonzonite molybdenum-copper occurrences. The Second Pond and Harborside prospects appear to be close to production. Systematic investigations for non-metallic deposits appear to have been aimed principally toward limestone, asbestos, diatomaceous earth, and spodumene-bearing pegmatites. Advances in prospecting methods, high metal prices, a favorable business outlook, increasing cooperation from large landholders, and some discoveries support the probability of increased exploration activity in Maine during the coming decade.

Jan 1, 1968

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sicurdson

Since the composition and structure of the beach sand concentrates correspond so closely to what would be expected of ilmenites that have been altered by oxidation and leaching, there is no reason to postulate the existence of the hypothetical compound, arizonite, to account for the composition of titaniferous beach sand concentrates. The four concentrates studied are examples of the different products that can result from various degrees of alteration of primary ilmenite. CONSIDERABLE uncertainty is revealed in the literature regarding the nature of the titanium minerals which make up the bulk of the heavy, opaque fractions of numerous beach sand deposits of the world. An investigation was made, therefore, of beach sand concentrates of North Carolina, Florida, Brazil, and India. Magnetic concentration, X-ray, and microscope data were obtained which show that these concentrates consist essentially of ilmenite and its alteration products. The alteration, brought about by oxidation and leaching of iron values, has resulted in upgrading the ores to a range of 56 to 64 pct TiO², as compared with 52.7 pct in ilmenite of theoretical composition. Conclusions drawn regarding the nature of the dominant titanium-bearing mineral in beach sand deposits have been based mainly on chemical composition, specific gravity, and petrography. This material has usually been referred to as ilmenite or weathered ilrnenite.: It has also been referred to as arizonite because in chemical composition it resembles an Occurrence in in which was described by Palmer' in 1909. The chemical composition of Palmer's arizonite corresponded closely to the formula Fe²O³ . 3TiOs. From approximate measurements of crystal angles on a large imperfect crystal with rounded faces, the

Jan 1, 1955

By J. Ruben Velasco, Roland B. Mulchay

CANANEA has long been recognized as a remarkable field for geologic study. The copper deposits and rocks of the district have been described by many geologists and engineers, but only the most general correlations have been made between Cananea sedimentary rocks and other known sedimentary sections in the southwestern United States and northern Mexico. The present paper describes the Cananea sediments in greater detail than has been done before and attempts to fit the Cananea sedimentary section more closely into the geologic time table. The lack of well-preserved fossils has made it difficult to date the sediments accurately in geo- logic time, but it is possible to make tentative correlations between the Cananea sediments and the southeastern Arizona sections, based largely upon lithology and general position in the geologic column. It appears that sedimentation at Cananea and Bisbee may have been closely similar during Paleozoic time. Even such generalized correlations, however, may be subject to considerable modification in the future. The present study has led to the recognition of other problems of age and mineralization relationships in the Cananea district. Cananea is located in the north-central part of the state of Sonora, Mexico, at an elevation of 5270 ft. It is about 135 miles northeast of Hermosillo, the state capital, and 25 miles south of the international boundary. By road Cananea is 40 miles from the twin towns of Naco, Ariz., and Naco, Sonora, and about 50 miles from Bisbee, Ariz. It is served by the Nogales-Naco branch of the railroad, F.C. Pacifico, and is connected with Chihuahua and Mexico City by the Aeronaves airline.

Jan 6, 1954

By Arnlf Muan, Bert Phillips

The quenching technique has been used for- a study of phase velntiorzs within the composition triangle 2CaO.Fe2O3-FeO.Fe2O3 Fe2O3 of the system Ca-Fe-O. Desired total compositions of sanzples were attained by weighing of starting materials in required proportions and keeping them in sealed 80 pct Pt 20 pct Rh tubes during equilibration .runs. The liquidus surface has been delineated. the existence of two ternary compounds has been established, and seven ternary inwariant situations have been determined. ONE unit within the research program on refractory oxides in progress in our laboratories is the study of phase relations in the system Ca-Fe-Si-O. The present paper deals with the ternary system 2CaOFe2O3-FeO.Fe2O3-Fe2O3, which is only a small part of the enormously complex quaternary system. Many of the phases occurring in iron ore sinter products have compositions which can be closely approximated within this ternary system, and a knowledge of stability relations existing among these phases may be expected to be a useful guide for improving sintering operations. Two fundamentally different experimental approach es are commonly used in studies of systems containing iron oxides, both permitting control of the oxidation state of Fe. One method consists in keeping constant the oxygen partial pressure of the gas phase in equilibrium with condensed phases (liquid and crystalline). In the other method, which is the one used in the present investigation, the total composition of condensed phases is kept essentially constant by keeping the samples in a gas-tight container. The details of this experimental procedure will be described in a later section. PREVIOUS WORK Extensive studies of phase relations in the bounding binary system FeOFe2O3-Fe2O3 have been reported by Greig, Posnjak, Merwin, and Sosman,' by Darken and Gurry,2, 3 and recently by Phillips and Muan.4 A diagram summarizing the results of these studies is shown in Fig. 1. Particular attention is

Jan 1, 1961

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

By A. E. J. Engel

INDUSTRIAL talcs and ground soapstones both include earth materials of different chemical and mineral compositions. In general, the industrial talcs are composed of silicates that contain appreciable amounts of magnesia. Generally talc, the mineral, is a predominant or at least common constituent. Talc, the mineral, is a hydrous magnesium silicate, with a suggested theoretical formula H2Mg3 (SiO3)4 or H2O.3MgO.4SiO2, which postulates 63.5 pct SiO2, 31.7 pct MgO, and 4.8 pct H20.11 Actually different single grains or leaves of pure talc have variations in water content ranging from 3.5 pct to more than 7 pct, as well as slight differences in the proportions of MgO and Si02.16 Only a very small percentage of the ground industrial talcs produced in the United States approaches the composition given above (see Table 1). The purer talcs invariably occur as alteration products of magnesium carbonate rocks. Some of these relatively pure talcs include compact, massive types largely mined in California, which are designated as steatite.38,58 In general, steatites cannot contain in excess of 1.5 pct CaO, 1.5 pct combined FeO and Fe203, and 4 pct A1203. The less pure varieties of massive talc and mixtures of magnesian silicates are commonly called soapstones, or merely talc. Many industrial earth products classified as talc or as soapstone contain a variety of minerals, especially serpentine (H4Mg,Si2O9), chlorites (hydrous magnesium, iron, aluminum silicates), tremolite (Ca2Mg5H2[SiO3]8), anthophyllite ([MgCa]SiO3), diopside (CaMg[SiO3]2), and quartz (SiO2). The carbonates calcite (CaC03), dolomite (CaMg[CO3]2), and magnesite (MgCO3) are also present in some industrial talcs and soapstones. Some of these minerals, as well as sulphides, sulphates, and iron and manganese oxides, if present at all or in excess of minute amounts, may alter the composition of the industrial talc sufficiently to restrict materially its use or to lower or destroy its value. These factors are discussed in a subsequent section of this chapter.

Jan 1, 1949

By S. Feuerstein, L. Rice

The effect of low pressures on the flow and fracture behavior of molybdenum is described. For poly crystalline samples, room-temperature tensile tests indicate greater ductility under 10 Torr than under intermediate pressures up to and including atmospheric pressure (760 Torr). In addition, tests conducted at 760 Torr under atmospheres of air, dry nitrogen, and purified argon exhibited no apparent difference in mechanical properties. Critical tests involving baking in situ as well as those involving single-crystal deformation further imply that the ductility effect is a pressure-dependent phenomenon related only to the fracture process. This dependency is discussed in terms of adsorption and diffusion contributions. THE effect of very low pressures on material properties has heretofore been presumed to be important only for substances possessing relatively high vapor pressures at ambient temperatures. Research has therefore been concentrated primarily on organic solids and liquids, and in some instances on metals such as zinc and cadmium. Most vacuum-effect studies' on the mechanical behavior of metals have been performed under conditions of either cyclic loading or creep rupture at elevated temperatures, i.e., over extended time periods. These studies were not restricted to high vapor pressure materials but also encompassed such metals as gold, copper, and nickel. Very little concern, however, was placed upon the importance of a vacuum environment on the mechanical behavior of metals subjected to a simple unidirectional deformation at ambient temperatures. A tension test is generally of short duration as compared to a creep test, and at room temperature vacuum effects if any would be expected to be surface-limited. In early 1963, Kramer and podlaseck2 reported a change in the bulk flow behavior of aluminum single crystals during room-temperature tension tests. The deformations were performed under pressure conditions of 760 to 3.4 X 10-8 Torr and indicated for the first time a vacuum surface effect contributing to the bulk tensile behavior of metal specimens. As a consequence, an experimental program was initiated in this Laboratory to study the effects of ultrahigh-vacuum conditions on the mechanical behavior of metals. The results of a preliminary study on poly-crystalline molybdenum3 revealed, unlike Kramer's observations of changes in the stress-strain behavior, only an increased ductility under ultrahigh vacuum. Flow behaviors were nearly identical for all tests re- gardless of pressure. This paper presents comprehensive results obtained in this area of research. 1) EXPERIMENTAL PROCEDURE Three material categories were used in this study: sintered and are-cast polycrystalline molybdenum of nominal purity 99.93+ pct and single-pass electron-beam zone-refined molybdenum single crystals having a nominal purity level of 99.99+ pct. The interstitial levels (weight percent) as determined by the Materials Testing Laboratories, Division of Magnaflux Corp., were as follows: sintered molybdenum (C— 0.005, H—0.0004, O—0.015, N—0.008); and arc-cast molybdenum (C-0.0038, H-0.0003, O-0.015, N-0.023). Single-crystal molybdenum obtained from Materials Research Corp. had a typical interstitial analysis of C-0.0015, H-0.00007, O—0.00045, and N-0.0001. Tensile specimens having a 5 mm diam by 50.8 mm length were prepared from these materials. An average grain diameter of 0.059 mm was obtained for the sintered specimens following a 4-hr, 1600°C heat treatment. Grain sizes from 0.019 to 0.149 mm were obtained in the arc-cast specimens following heat treatments from 1100° to 1600°C for 1 hr. This series of specimens was used exclusively for the grain-size effect studies. All samples were electrolytically polished in 97 pct sulfuric acid solution prior to testing. Experiments were performed at room temperature in an ion-pumped ultrahigh-vacuum system positioned in an Instron tensile machine, Fig. 1. A constant strain rate of 4.2 x 10-4 sec-1 as derived from crosshead displacement was assumed for the deformations. Starting vacuums ranged from 2 to 0.5 X 10-10 Torr. These pressure measurements were made using corrected values4 of an NRC Redhead gage. Comparative readings were also made against a G.E. triggered dis-

Jan 1, 1967

By Henry G. Granger

NOTHING in this paper is to be understood as even suggesting a moment's suspension of the splendid work now going forward on the Isthmus of Panama, except so far as it is related to the proposed locks. All the work already done, and all material purchased or ordered, would be available for the plan herein proposed. The situation and the problem concerned may be summarized as. follows : The scheme of a lock-canal through the Isthmus of Panama was adopted, as is well known, on two principal grounds-namely, the greater expense of a sea-level canal, and the longer time required for its construction. Of these, the latter is believed to have been the more influential. But further developments have diminished the weight of both, so that a reconsideration of the question is warranted. It is the purpose of this paper to advocate such a reconsideration-emphasizing the importance of certain objections to the lock-canal not mentioned or not duly appreciated in the report of those members of the International Board of Consulting Engineers who favored this form; showing the nature and bearing of the new facts developed; and, finally, proposing a combination of well-known methods and apparatus, which would, in my judgment, effect the construction of a sea-level canal in less time, and perhaps at no greater cost, than will be required for the remaining work on the lock-canal. I. OBJECTIONS TO A LOCK-CANAL. 1. Earthquakes. Two centuries ago Panama is said to have been destroyed by an earthquake. In 1882 a rather violent earthquake was felt at the southern end of the Isthmus. In 1898 I felt a slight shock near the present border-line of Colombia. In 1900 I felt three shocks at Quibdo, the head of navigation of the

Jan 1, 1909

By AIME AIME

T HE 121st meeting of the Institute held in New York City, February 16 to 19, 1920, was a great success despite vicissitudes of weather of unusual severity. On account of tremendous snowstorms, only two members of the Canadian contingent arrived, and several of our members from the west arrived thirty hours late. Two weeks prior to the meeting, the heaviest snowstorm in 34 years wrecked the surface transportation in New York; and it was only by special dispensation that arrangements were effected, with the New York Street Cleaning Department to clear away 39th street in front of this building so that vehicles could reach the curb. The total registration of members and guests was 1138.

Jan 1, 1920

By Leo H. Glanville

UNTIL 1934, natural ventilation was depended upon in the mine of the Climax Molybdenum Co. at Climax, Colorado. In that year a 7-ft. axial-flow, low-pressure fan was installed as an exhausting unit. In 1936, three more fans of the same kind were installed, all as exhausting units, with a total capacity of 115,000 cu. ft. per min., and since then fans and sprays have been added as required. ATMOSPHERIC CONDITIONS Adverse atmospheric conditions at this elevation of 11,500 ft. account in part for difficulty in maintaining adequate ventilation throughout the mine. Barometric pressures range from 18.99 to 20.01 in. of mercury; the normal average being 19.70 in. Air weight is 0.051 lb. per cu. ft., and humidity is low-about a 30 per cent yearly average. This makes the use of mechanical humidity aids mandatory the year around to prevent excessive dryness of the mine workings and the resultant dust hazard. The yearly temperature range is from minus 24° to 95°F.; typically, in February 1942 the mean low was minus 3.25°F. and the mean high, 21.3°F. In August the mean low was 34.8°F.; the mean high, 64.26°F. Even during the summer month air filtration through the openings of the cave area is 32°F., owing to accumulation of snow in the glory hole and in part to glacial ice, which, combined with a rock temperature of 39°F. on the upper levels (elevation 11,945 ft.) and 42°F. on the main haulage level (elevation 11,490 ft.), makes it difficult to maintain a comfortable working temperature. The one advantage in ventilation of mine workings at the altitude of the Climax mine is that the power required to circulate a given air volume is 32 per cent less than would be required at sea level. PROBLEMS Since 1936 the mine management has studied intensively plans for providing adequate ventilation for the entire mine for its expected life. As the ore breaks into large pieces, much secondary blasting is necessary, therefore there is a considerable amount of smoke, gas and dust, which requires circulation of a large amount of air to remove the contamination. It is undesirable to use haulage drifts and manways as air passages because some would be passageways for contaminated air also, and there would be undesirable high velocities in some drifts. High velocities and large volumes of subfreezing air dry out the passageways through which they pass, and thus increase the amount of dust. Regulating doors in haulage drifts are difficult of upkeep and interfere with production. It was decided as a general principle to distribute fresh air to each working place at low velocities and low pressures and to remove contaminated air as soon as possible with a minimum of travel through working places.

Jan 1, 1943

By W. I. Duvall, L. D. Sadwin

Three explosives with different detonation characteristics were tested by studying their cratering ability in a granite-gneiss. The strain wave generating characteristics of these explosives were also studied in the same rock medium. Correlations between the relative performance of three explosives as evaluated by crater studies and other methods of evaluation are indicated. Numerous test methods have been employed to evaluate the output performance of explosives; for example, the underwater explosion method, the airblast method and the ballistic pendulum method.'*' For blasting applications, the study of explosion produced craters and explosion generated strain waves are the most meaningful. This laboratory has employed these techniques extensively for many years and has shown that the detonation properties of explosives and their ability to generate strain waves in rock are related and that the amplitude and shape of the strain wave is related to some of the crater parameters such as slab thickness and fly rock velocity.3'11 However, a good comparison between the relative performance of explosives as determined by the crater and strain wave methods had not been made. The purpose of this investigation was to determine if the relative performance of three explosives as determined by the crater method shows a correlation with the relative performance as determined by the strain wave method. If a good correlation exists between these two sets of relative performance, it should then be possible to relate the detonation properties of an explosive to its ability to break rock in a crater test. In most commercial blasting operations, the diameter of the blast hole remains constant even though the type of explosive may change. In general, it is the explosive volume rather than the weight which remains constant when two or more explosives of different density are compared. Therefore all tests in this investigation were conducted on a constant volume basis rather than on a constant weight basis. TEST SITE AND ROCK PROPERTIES The tests described in this paper were conducted at a granite quarry owned and operated by the Consolidated Quarries Div. of the Georgia Marble Co. at Lithonia, Ga. The tests were performed in an area where the exposed rock surface was nearly horizontal and where the general rock mass had few joints or faults. The rock has an apparent sp gr of 2.6 and a longitudinal propagation velocity of 18,000 fps. The characteristic impedance of Lithonia granite gneiss is 53(lb - sec/in3). EXPERIMENTAL PROCEDURE There are many parameters which must be considered in the study of explosion-produced craters. The role played by each variable in the explosive-rock-crater system can be determined by experimental techniques in which one parameter is varied while others are maintained constant. In this investigation, the crater geometry was studied as the depth was varied for each of three explosives. The explosive volume and rock-type were held constant for all crater tests. The experimental arrangement used in performing the crater tests is illustrated schematically in Fig. 1.

Jan 1, 1965

By Morris M. Fine, Norwood B. Melcher

It is out of the question, at this time, to select any one prereduction process as superior to the others. It is apparent that several share a basic similarity and that within the groups listed in Part 1, the reduction vessel is sometimes the only significant variable. Claims as to the virtues of one machine over another are difficult to substantiate: one may be rapid, another thermally frugal. Based on published data, however, all seem to be performing adequately. It would appear that processes based on carbonized pellets are most applicable to foundry iron at low production rates. Adaptation to large scale manufacture of blast furnace hot metal or to agglomeration of fine concentrates at the mine site is much less likely.

Jan 8, 1966