Search Documents

By ROBERT. RICHARDS

I. INTRODUCTION The object of this paper is to enlarge the field of settling velocities treated by me in my former papers, Close Sizing Before Jigging, and Sorting Before Sizing.' There seemed need of work both on coarser and on finer sizes. Messrs. A. Sidney Warren and M. L. Nagel undertook the investigation for the coarser sizes, from 12.85 mm. down to 2.05 mm. diameter. Their work, because of the closer spacing and because of the increased number of observations and consequent stronger averages, called for a revision of the former work. Messrs. G., A. Barnaby and Ralph Hayden undertook this part of the work, from 2.49 mm. down to 0.28 mm., which is near the limit of sifting. Their work covers the ground much more minutely and comprehensively than the former papers. There remained to be covered the portion of the field too fine for investigation with the sieves. This part, covering the range of grains from 0.48 to 0.03 mm., was undertaken by Mr. E. S. Bardwell. For it he used the elutriation method. II. THE FIRST, OR COARSEST, SECTION OF THE FIELD. The first desideratum in this investigation was a series of sieves for sizing the sands preparatory to making the tests. It became necessary, therefore, to decide on a sieve-scale for this purpose. A sieve-scale is a series of sieves in which the dimensions of the holes of the successive members form a series increasing by a. definite ratio. There are three natural sieve-scales : 1, progressing by doubling the width of the hole for each suc-

May 1, 1907

By R. K. Datta

Eluropium -activated yttrium vanadate, excited by short- and long-wavelength ultraviolet radiations, shows enzission lines near 6100A, the principal ones correspondirzg to transitions of EU+3 ions from 5Do to the F2 energy level. The ~neclmlallistns of absorption and etnissiorz of this phosphor have been empirically studied. The absorption is caused by two separate processes in the matrix. The phosphor YVO4:Eu and tlie matrix YVO, haue essentially the same resectance spectra in the region 2500 to 4000if. There are two broat ah~o?~ption bands: natnely, around 2600 and 3600A regions. Whet? compared with the reflectance spectra of the constituent oxides, namely, Y2O3, V205, Eu2 03, the absorption bands of the tnatvix and the phosphor in the short- and long-wavelength ultraviolet regions can be interpreted as due to charge-transfer processes involving i) Y-O and ii) 17-0, respecti~~ely. The excitation spectrum' of the phosphor has two broad bands with peaks at about 2600 and 3600A regions. U can be postulated that enevgy absorbed under short- crud long-wavelength ultraziolet excitatzon, respectzcely, by Y-0 and V-O parts of the niatrix is transferred by radcatio~zless process to EU+3 ions. Thzs postulate can empirically be proved on the basis of the spectra of the systems (YVO4,-YPO4,):Eu. PO? ~ons do not have' any appreciable absorption in the short or long uv regions. When P0't3 ions are substitlited for v0i3 ions in YVO,:Eu phosphors, the absorption and excitation in the lo~zg uv region are gradually reduced. Ailoreover, the £«+3 emission under 3650A excitation is decreased zuitlz increase in PO^ content, lt~lzereas the emission under 253711 excitation remains esserztially constant with as IILUCIL as 60 mole pct of YPO, in YVO,:En. EUROPIUM-activated yttrium vanadate (YV04:Eu) is a well-known phosptor.'-3 When excited by cathode rays, 2537, or 3650A radiations, YV04:Eu emits typical narrow-band spectrum of EU'3 fluorescence in the region of 5900 to 7100A, a very strong maximum occurring at about 6190A. This emission is considered to be due to 5Do — 7F2 transition of excite: EU*3 in 4f state. Moreover, the emission under 3650A excitation increases with temperature markedly. Because of these properties, YV04:Eu phosphor finds wide application in industries, namely, in color television tube, laser, and high-pressure mercury-vapor lamps. It is the purpose of this paper 1) to present the empirical study of the mechanism of absorption and excitation of YV04:Eu phosphor by ultraviolet radiation, and 2) to offer an explanation for the process of emission. It should be mentioned that a theoretical discussion on the mechanism of absorption in terms of the crystal or ligand field theory is beyond the scope of this paper. Empirical studies presented here are based primarily on spectroscopic and crystal-chemical investigations. EXPERIMENTAL i) Preparation of Materials. The synthesis of vanadate phosphorinvolves preparation of (Yi-.tEuj^Oj, blending the mixed oxide with an oxidic compound of vanadium, such as V205 or NH4V03, and firing the mixture at about 1000°C for several hours when YVO4:Eu forms as a primary phase. (Y1-xEux)203 compositions are prepared by coprecipitation of oxalates, and igniting them at about 1000°C. The vanadium compound is added in excess of the stoichiometric proportion for fluxing purposes. The charge is cooled, ground, and the excess of vanadium is removed by a hot wash (-80°C) of alkali or ammonia. Y(VP)04:Eu samples are prepared by mixing (Yi-xEux)203 with stoichio-metric proportions of (NH4)2HP04 and the vanadium compound. The mixtures are prefired at 700" to 800°C for 1 or 2 hr, then ground and refired at 1150°C. The firings of the phosphors are done in silica crucibles, and the homogeneity of the final products checked by X-ray diffraction analysis. ii) Spectroscopic Measurements. Diffuse reflectance sqectra of the samples within the range 2500 to 7000A are obtained by using CaF2 as standard in Cary Recording Spectrophotometer, Model No. 14. The emission spectra from phosphor plaques, excited under different ultraviolet sources, are obtained by a direct-recording spectroradiometer4 adapted with a grating monochromator with nearly constant dispersion. Maximym sensitivity in the spectral region from 2500 to 7000A is obtained with a quartz-windowed, S-20 response p$otomultiplier. The total' band pass is kept about 30A. The spectra are calibrated against the light from a standard tungsten filament lamp reflected from a magnesium-oxide plaque. Brightness data given throughout this report $re measured from the height of the main peak (6190A) of the emission spectra. The excitation spectra are measured using sodium salicy-late as standard. RESULTS AND DISCUSSION The diffuse reflectance spectra of both pure and activated YV04, along with their constituent components, are shown in Fig. 1. YVO4 shows two broad absorption bands, namely, around 2500 and 3600A, respectively. Since there is little difference between the reflectance spectraoof YVO4 and YVO,:Eu in the uv region (2500 to 4000A), it can be postulated that excitation of the phosphor is mainly due to absorption by the matrix, i.e., YVO4. The question, now, is whether the matrix (Yv04) is excited as a whole, or different components are responsible for the two absorption bands. The characteristic absorption spectra of molecular ions involving transition metal ions, both in aqueous solutions and in crystals, are due to electronic transi-

Jan 1, 1968

By O. D. Sherby, J. E. Dorn

SEVERAL years ago Zener and Hollomon1 suggested that the flow stress of metals might be related to the temperature and strain rate in accord with the functional equation: s=s(eeh/rt) [1] at the same state. The Zener-Hollomon relation also contains the significant tacit implication that the energy for activation, AH, is substantially independent of the state of the material. The utility of this method for correlating creep data with tensile data was illustrated in a preliminary reportL on the effect of alloying additions on the secondary creep rates of binary a solid solutions in aluminum as shown for Al-Mg alloys in Fig. 1. Not only do the secondary creep and ultimate tensile properties for each alloy correlate well on this plot but in addition the activation energy, AH = 17,900 R cal per mol. is identical for the various compositions. Similar types of curves correlating the secondary creep rates at 422°K (300°F) with ultimate tensile data were also obtained for a series of dilute a solid solutions of copper, germanium, zinc, and silver in aluminum. In all cases the activation energy for creep, AH, was found to be equal to about 17,900 R cal per mol independent of the type of alloying element or its concentration. The coincidence of the activation energies for these alloys is probably due to the fact that the activation energies for creep are rather insensitive to small composition changes. Alloying additions, as shown in Fig. 1, however, increased the stress necessary to obtain equivalent values of ee?H/RT. Thus the stress level in curves of the type represented by Fig. 1 gives the relative creep strengths of the various alloys. Inasmuch as these correlations between creep and tensile data were obtained for creep tests at 422°K, it appeared advisable to ascertain the range of secondary creep rates and temperatures over which correlations between creep and tensile data could be made on the basis of the Zener-Hollomon relationship. If, for example, the activation energy changes with different ranges of creep temperatures, the utility of the proposed analysis would be severely weakened. But if AH is constant not only for all dilute alloys, but also over wide ranges of temperature and secondary creep rates, confidence will be developed not only in the broad utility of the Zener- Table I. Chemical Analysis':' and Grain Size of Alloys Mean Grain Residual Impurities. Wt Pct Diam- Alloying Atomic-eter, Element Pct Si Fe Cu Mg Mn mm Aluminum 99.987 0.003 0.003 0.006 0.001 0.25 Magnesium 1.617 0.003 0.004 0.006 0.26 Copper 0.101 0.003 0.003 0.0006 0.001 0.29 Zinc 1.616 0.003 0.005 0.007 0.001 '0.26 * The authors express their appreciation to the Aluminum Company of America for the preparation and chemical analyses of these alloys. Hollomon relationship, but also in its theoretical justification. The following investigation was instituted in order to ascertain the range of validity of the Zener-Hollomon relationship when it is applied to creep and tension data. Materials, Equipment, Technique In view of rather extensive correlatable data now available on the plastic properties of a series of binary a solid solutions of magnesium, copper, germanium, zinc, and silver in aluminum, these alloys were again selected for the present investigation. Previous reports have already covered the tensile properties of these alloys at subatmospheric temperatures," and at elevated temperature," as well as their fatigue properties at atmospheric temperatures, nd their creep properties at 422°K.' Resistivity measurementsa as well as precision lattice constant determinations? evealed that these alloys are a solid solutions. After homogenization. 0.100 in. thick sheets were rolled to 0.070 in. in thickness and recrystallized to about the same grain size. Since the details of these treatments were reported previously," they will not be repeated here. In order to appropriately reduce the scope of creep tests in this investigation only the typical alloys shown in Table I were investigated. All creep specimens were machined such that their tensile axes were in the rolling direction of the 0.070 in. sheet stock. The gage section was 2 in. long and 0.500 in. wide with a reduced section of 3.50 in. Creep strains were measured by means of rack and pinion type extensometers with a sensitivity of 0.005 in. per division. Readings were estimated to 1/10 of

Jan 1, 1953

By WILKES BARRE

AS PREVIOUSLY announced, the semi-centennial meeting of the Institute is to be held at Wilkes-Barre, Pa., on Sept. 12, 13, 14, and 15. An interesting program of technical sessions and excursions is now being prepared by the Local Committee. At the time of going to press the program had not been completed in sufficient detail to permit its being pub¬lished in this number. The detailed program will be published in the September MINING AND METALLURGY, which will be printed in time to be distributed before the Wilkes-Barre Meeting. It may be said in advance, however, that the Com¬mittee has progressed so far in its work that we are assured of one of the -most notable meetings the Insti¬tute has held and that members will miss a rare .treat if they do not attend. The many trips and excursions, as well as the banquet, will be -given to the members as a compliment from the members of the Local Com¬mittee. . . The paper by Howard Eavenson on the Lynch Plant of -the United States Coal and Coke Co. will be illustrated by lantern slides and moving pictures. One of the most appropriate discussions will be that opened by Prof. J. F. Kemp on the Stratigraphy of the Anthracite Region; this also will be amply illustrated.

Jan 1, 1921

By John A. Church

Jan 1, 1903

By B. S. Tani, R. V. Schablaske, M. G. Chasanov

In the Ti-Cd system two intermediate phases, TiCd and Ti Cd, have been found and characterized by X-ray diffraction powder techniques. An earlier reference' had reported the existence of the compound Tisd. No structural details, however, were given nor was there any indication of the possible existence of other binary compounds. Studies of the solubility of titanium in liquid cadmium2 led to the discovery of both TiCd and Tisd. The solid phase in equilibrium with saturated solutions of titanium in liquid cadmium at temperatures below 620°C is TiCd, whereas TizCd is the equilibrium solid phase above 620°C. Both thermal analysis and X-ray studies show that a peritectic reaction between the y phase (~isd) and cadmium to form the 6 phase (Ti Cd) occurs at 620°C. X-ray diffraction powder photographs of material isolated from the ingots used in the solubility measurements as well as material prepared by a direct heat of the appropriate stoichiometric amounts of titanium and cadmium can be indexed on the basis of a tetragonal unit cell with a = 2.904 ± 0.002A, co = 8.954 * 0.004A, c/a = 3.083. No variation of lattice parameters indicative of a range of composition is evident. With four atoms in the unit cell the calculated density of the intermetallic is 7.05 g per cm3; the observed value is 7.07 g per cm3. The TiCd lattice is primitive as indicated by the fact that there are no systematic absences among hkl reflections. The absence of all hko reflections for which h + k = 2n + 1 is also evident. This systematic absence indicates the following two space groups, C\h — P4/n and D&~4/nmm; both groups, however, have the same two- and four-fold positions. Stoichiometry, symmetry and space group indicate two likely structure types. They are the PbO-litharge3 (B10) type and the Ti CU (B11) type. Spatial considerations favor the B11 structure with atoms placed in the following positions: 2Ti (c) 0, 1/2, Z; l/2, 0, Z 2Cd(c) 0, 1/2, Z; 1/2, 0, Z The TiCd structure may be summarily described as a layered structure in which double cadmium layers alternate with double titanium layers along the c-axis. The best agreement between calculated and observed intensities is obtained for the values ZTi = 0.608 and ZCd = 0.130. Calculated and observed powder intensities as well as other pertinent powder data are recorded in Table I. Interatomic distances for the proposed structure are recorded in Table II and are to be compared with the distances of closest approach for titanium and cad-

Jan 1, 1962

By J. W. Hickman

INTRODUCTION MOST of the electron diffraction studies of oxide films which form on metals and alloys have been carried out by oxidizing the specimens in an auxiliary furnace, cooling down to room temperature and then inserting the sample in the camera and taking a diffraction photograph. Prior to the investigations at the Westinghouse Research Laboratories, no systematic study of the oxidation of any metal or alloy had been made over a wide temperature range with photographs taken at elevated temperatures except the investigation of iron by Jackson and Quarrell.1 In order to interpret the electron diffraction patterns of the oxides which may form on alloys, it seemed advisable to make a comprehensive study of the oxidation of the purest metals available in the bulk form. Thus far studies have been completed on iron,2 cobalt,2 nickel,2 chromium ,2 Copper2, tungsten,3 molybdenum,3 beryllium ,4 uranium,4 thorium4 titanium5 and zirconium5 while investigations are in progress on tantalum and columbium, The next step in the study is concerned with the investigation of the oxides which form on binary alloys. Some of the alloys consist of a single, phase while others contain more than one phase. The identification of the oxides on the surface of a binary alloy may be more difficult than on the metals since oxides containing both metals as well as those of each metal separately may form. Furthermore, it is possible that solid solutions of the various oxides may occur. In these cases the electron diffraction method may not be able to identify the oxidation products unequivocally, Examples of solid solutions which may present difficulties are MoO2 and W02, Fe3O4 and FeO-Cr2O3 since the diffraction patterns are so similar. Since electron diffraction can determine only the structure of the oxide, the chemical composition must be inferred from the diffraction data based upon X ray diffraction investigations of specimens of known composition. It is possible in some cases to decide whether a given solid phase reaction can occur on the surface of an alloy by a study of available thermodynamic data. Table I lists the equations for the formation of most of the oxides from the elements together with values of log10 KR for the several temperatures. [OF°R = -RT In KR 0 and-~75T = logi°KR] [?F°R] and KR are the free energy and equilibrium constant of the reaction. Calculations may be made using the values given in Table I to determine whether a given solid phase reaction is possible thermodynamically. For example, a solid phase reaction should occur between aluminum and chromium' oxide to form

Jan 1, 1948

By G. B. Sazuyer

DEVELOPMENTS respecting beryllium during the past year have been sufficient to center attention on it as likely to be the most important of any of the chemical elements that have recently found a place for themselves in technical industry. This importance is only potential, however, largely because adequate supplies of beryllium ore will be necessary. The beryllium industry will be only as great as the mines which support it. To find and develop large mines will be the problem. Chief of the immediate commercial developments in the United States is beryllium-copper and its espousal by Anaconda and Riverside even at present high prices. According to the pamphlets of these companies, it ap¬pears that beryllium is to copper nearly what carbon is to iron. When one considers that the tensile strength of pure copper is about 33,000 lb. per sq. in., but that the addition of 1.5 to 2.5 per cent of beryllium produces a heat-treatable alloy with a maximum tensile strength of 220,000 lb. or over, the analogy to carbon and iron is made strikingly, clear. Striking among the properties of beryllium-copper is its resistance to fatigue, claimed to be equal or superior to that of spring steel. It needs little imagination to foresee a great industry for this alloy alone.

Jan 1, 1934

Jan 1, 1959

By R. J. Wasilewski

THERMAL expansion of rhenium data have been reported by Agte et al.,&apos; and Medoff and cadoff,&apos; respectively, while the linear expansion coefficient was determined by Sims et Al.3 Denoting expansion coefficients parallel and at right angle to c axis by all and Al respectively, their weighted mean should be equal to dilatometric linear coefficient of a random polycrystalline specimen. The values reported for these coefficients are tabulated below: Since these values are in poor agreement, and because of anomalous expansion behavior observed in titanium 4 and chromium, a rede termination of the axial expansion was carried out. A Unicam 19-cm-diam high-temperature camera was used, with unfiltered CuK radiation. Camera calibration was carried out using at Pt wire standarde at temperatures up to 1100oC, the variation between indicated and true temperature being within the experimental error (estimated at <3oC) above 750o C. Rhenium Johnson Matthey spectrographic standard) was vacuum annealed at 1000 oC prior to X-ray diffraction experiments. Lattice parameters were obtained by least-squares solution using the reflec- tions (1232), (1015), (2024), and (3030) for all the patterns, and the additional reflection (2133) for higher temperature (400°C and above) patterns. The relative expansion data obtained are shown in Fig. 1, lengths of the vertical bars indicating the spread in the parameter values obtained by using various combinations of three spacings from the four or five measured. The data calculated from the equation of Ref. 2 are included for comparison purposes. Several specimens were used to obtain the above data, neither of them showing a significant parameter change after completion of the high temperature runs. Some parameter data and the corresponding expansion coefficients between 25 oC and the measurement temperature are tabulated below. The comparison of the present data with those previously reported shows reasonable agreement with the results of Medoff and cadoff2 within the temperature range covered by them (up to 1000 oC). The a values are appreciably higher throughout most of the investigated temperature range. The basal expansion is—in agreement with their findings—appreciably higher than that in the direction of hexagonal axis. The expansion coefficient, al, however, decreases rather more slowly with temperature than previously reported. The expansion along the c axis up to nearly 1000°C appears in excellent agreement. However, at higher temperatures there is a marked deviation towards higher expansion, reproducible between different specimens. Furthermore, there seems to be some irregularity in the variation of all with temperature, the apparent local minimum and maximum values at 510o and 1024o C, Table II, being well outside the experimental error limits. It must be stressed that the apparent discontinuity in the c parameter expansion is still insufficient to account for the expansion value reported by Agte et al.&apos; since a total expansion of close to 2 pct would

Jan 1, 1962

By K. A. Pauly

(Wilkes-Barre Meeting, June, 1911.) COMPRESSED air has been and is still very extensively used in connection with mining-operations, but its application in the past has been almost entirely confined to supplying power to underground machinery. Its introduction was due to the difficulty of taking care of the steam which is exhausted underground, rather than to any advantage in efficiency to be gained by its use. The ease with which electric power may be carried to the remotest parts of the mine and the high efficiency of the electric motor have long been appreciated by mine-operators, and electric power is now extensively used underground in the more recent developments, while many of the compressed-air engines in the older workings are being rapidly replaced by electric motors. Recently, however, it has been suggested to use compressed air for driving the large shaft-hoists, the air for the engines being supplied by electrically-driven compressors, and an installation of this character is being erected at Butte; Mont. It is the object of this paper to compare the compressed-air system of hoisting with the various electrical systems, from the stand-points of first-cost and cost of operation. However, before entering into a discussion of the various systems, it will be well to consider briefly the conditions affecting the choice of a system of hoisting in which electricity is the ultimate source of power. The power required by a mine-hoist is extremely intermittent and fluctuates between very wide limits, the all-day average consumption of power not exceeding from 5 to 15 per cent. of the maximum demand during hoisting. The cost of supplying power for such a fluctuating load is necessarily higher than that for supplying an equal amount of

Dec 1, 1911

By John T. Cumberlidge, Frederic M. Chace

Nickel-bearing saprolite developed during the early Tertiary over a northeast trending ultramafic body of Jurassic age near Riddle in southwestern Oregon. The principal nickel mineral is garnierite, but other complex nickel minerals may be present. There are two main ore bodies, an upper (older) one associated with the Klamath peneplain, and a lower (younger) one on the Sherwood peneplain. Saprolite constitutes the bulk of the ore and was probably derived from peridotite and dunite through chemical decomposition by downward percolating meteoric groundwater. Decomposition took place by net loss of MgO, SiO2, and Fe without a change in volume. Faults and joints provided permeable zones which localized saprolite development, and faulting may have helped preserve some ore from loss by erosion. Garnierite-chalcedony boxwork ore was deposited by meteoric groundwater along faults, joints, and at the level of former water tables. Boxwork ore is entirely supergene, the chemical constituents having been derived from higher in the soil profile. The saprolites show evidence of both supergene and residual enrichment in nickel. Red and yellow soil occurs as a capping over saprolite and boxwork, and was derived from them by chemical and mechanical decomposition. The present deposits are probably truncated remnants of a formerly thicker and much more extensive deposit which probably included laterite at the surface. The deposits started to form in the early Tertiary due to deep chemical weathering under sub-tropical to warmtemperature conditions. Early Tertiary ero~ion surfaces of low relief probably contributed to the predominance of chemical weathering over mechanical erosion. Alteration under present climatic conditions favors the formation of soil from saprolite rather than the formation of new saprolite from peridotite.

Jan 1, 1968

By Juhani Pulkkinen, Pekka Lappalainen

Preplaced cable bolts - fully grouted old hoisting cables or stress relieved steel strands - have been used succesfully to pre- reinforce ore contact zones and pillars in sublevel stoping at Outo- kumpu Oy mines for ten years. The purpose is to make open stoping methods possible even in "poor&apos;&apos; conditions and to decrease waste rock dilution. Since 1971 more than 120 km cable bolting has been done, and plans for this year in five mines amount to 33 km. In order to understand the function of cable bolt, pull-out tests have been done both in the laboratory and in situ. Bond strength between cable and cement is highly dependent on cable structure and cable surface dirtiness. Steel cables with steel core and rough surface structure have highest bond strength ( 6 MP~). A cable bolt is a friction bolt. After losing its peak bond strength - after starting to move - a cable bolt still has a high loading capacity due to the friction caused by the uneven surface of the cable. Cable bolting is done before actual stoping from existing drifts, sublevel drifts, e.g. or from special bolting drifts. In general stress relieved steel strands are used; 2 x 15.2 mm dia per hole. FEM or BEM calculation is utilized in cable bolting design. Bolts 2 are in fan shape, 10 m ... 50 m long and are spaced 1/20 m ... 1/50 m2 at stope walls. Pretensioning of cable is not needed, when bolting is done before rock deformations. Bolting costs vary between 0.3 USD ... 1.0 USD/ore ton. In the beginning only manual cable installing technique bras used. Now bolting can be done as fully mechanized with the developed cable bolting machine; i.e. drilling of the hole, installing and cutting of cables and grouting of hole.

Jan 1, 1983

By Howard Martens, Pol Duwez

IN two papers published in 1949, alloys of chromium with the refractory metals tungsten, molybdenum, tantalum, and columbium were investigated in view of their possible use as high temperature resisting materials. For the Cr-Ta system, a partial phase diagram was presented and the only intermediate phase was identified at Ta2Cr3. A phase of the same composition was also observed in the Cb-Cr system. The X-ray diffraction data presented in these papers, however, were insufficient for crystal structure determination. It is shown in the present study that the only intermediate phase in both the Ta-Cr and the Cb-Cr systems corresponds to the ideal stoichiometric ratio TaCr2, or CbCr2. Both structures are cubic, MgCu, type. At high temperature, however, TaCr2 has a hexagonal MgZn, type structure, which can be retained at room temperature by fast cooling. The alloys were prepared by melting in a helium arc furnace on a water-cooled plate. The design of the furnace was essentially the same as that described in ref. 3. Some alloys were also obtained by sintering compacts made of the mixed powders pressed at 80,000 psi. The sintering was carried on for 4 hr at 1375°C. The tantalum and columbium powders were supplied by Fansteel Metallurgical Corp., North Chicago, 111. The tantalum powder was the reagent grade, with a particle size smaller than 400 mesh and a total impurity content less than 0.1 pct. The columbium powder was smaller than 325 mesh and contained approximately 0.1 pct C and traces of Fe, Ti, and Zr. The electrolytic chromium powder from Charles Hardy, Inc., New York, was smaller than 300 mesh and contained about 0.1 pct Na, 0.05 pct Ca, and traces of Cu, Al, Mg, Si, and Co. Powder diffraction patterns were obtained with a 14.32 cm camera, using copper Ka radiation filtered through nickel foil. The powder pattern of the TaCr2 alloy obtained by sintering at 1375&apos;C was different from that obtained on the same alloy rapidly cooled from the melt. Contrary to this result, the powder pattern of CbCr2 was the same, whether the alloy was made by sintering at 1375°C or by melting, and was similar to that of the TaCr, sintered. It was also found that the structure of the TaCr2 specimen obtained by melting was retained after heating for 4 hr at 1590°C, but transformed into the structure found in the sintered specimen after heating for 4 hr at 1375°C. Hence, the structural change of TaCr2, appears to be a reversible polymorphic transformation. CbCr2 and ToCr2 Structure, Low Temperature Form By using large scale Hull-Davey charts, the powder pattern of CbCr, and of the low temperature form of TaCr2 were readily interpreted on the basis of a face-centered cubic lattice with a parameter of approximately 6.95 kX. The indices of the reflections together with the values of sin&apos; 0 are given in Tables I and 11. From this list of observed reflections, it appears that the (200), (600), (024), (046), and (028) reflections are missing. The lack of (h00) reflections for h 4n indicates a four-fold screw axis. The missing (Okl) spectra for k + 1 An indicate the existence of a diamond glide d. The combination of these symmetry elements can be found in the O— Fd3m space group, which is therefore the most probable one. After having determined the approximate density of TaCr, by the immersion method, the number of molecules per unit cell was calculated and found to be nearly eight. This information, added to the fact that the most probable space group is O leads to the consideration of a structure of the MgCu2 type, in which the atoms have the following positions: 8 magnesium in a and 16 copper in d. On the basis of this structure, intensities were computed by means of the usual formula: 1 cos&apos;20 I a sin2 cos where F is the structure factor; 8, the Bragg angle: and p, the multiplicity factor. As shown in Tables I

Jan 1, 1953

By R. C. de Lange

An improved replica technique is developed for a nondestructive study of the nucleation and growth of fatigue cracks. Three different growth stages of a fatigue crack were observed. An initial stage of high growth rate is followed by a long period of very slow growth, until finally a third period of high growth rate leads to fracture. THE metal-fatigue process is of a very complex nature. The experimental approach towards fatigue is susceptible to many minor influences which, together with the unavoidable scatter in testing results, makes the interpretation a matter of extreme care. The generally accepted fact that, in a homogeneous material, the fatigue cracks start at a free surface indicates that surface studies may contri-but in an essential way to a better understanding of the fatigue mechanisms. Indeed metallographic observations of the fatigue phenomena have been very fruitful in the last decade. The study of extrusions, intrusions, and persistent slip bands has contributed much to the present knowledge of the early processes in fatigue.&apos; The drawback of the current metallographic techniques lies in the fact, however, that either observations of fatigue phenomena had to be made in a destructive way after an only partly executed test or a sequence of observations on the same test bar was only possible on notched specimens.2 4 In both cases an uncertainty exists as to the nucleation and growth of the fatigue crack in an unnotched test bar, where the crack can start at any place of a large area and develops in a test bar, which is macroscopically

Jan 1, 1964

Jan 1, 1962

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster&apos;s New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By Clyde E. Williams

THIS review of the progress made in iron and steel metallurgy during the past year is confined to developments in this country. It attempts to give examples to illustrate progress made rather than to appraise results. As a result of the gradually diminishing supply of rich iron ores and of predictions made as to the probable life of the iron-ore reserves of the Lake Superior District, attention of iron and steel executives was directed to the question of beneficiation of iron ores. Laboratory and plant-scale experimental work was conducted on the wash ores .of Minnesota and an investigation, was, begun on the Old Range low-grade ores.

Jan 1, 1931

By R. C. Philp, Allan Gibb

INTRODUCTION. THE term matte is applied to smelting-products so extremely diverse in composition and physical properties that it appears impossible to devise any generic formula to represent, chemically, the manner in which the varied proportions of the almost unlimited possible constituents combine with each other. Mattes produced in copper-smelting, in distinction from those produced in smelting-operations in which the recovery of copper is secondary to that of other metals, cover a narrower range in composition. The copper-content of such mattes vary from 20 to 80 per cent., and even this range is much smaller in general practice since it is found advantageous, when possible, to produce mattes with about. 50 per cent. of copper in the first operation. Further, it is unusual that arsenic or antimony occurs in copper-ores in sufficient proportions to form arsenides or antimonides in such quantities that they will separate out from the furnace-products, as is common in lead-smelting. Generally, the mattes produced in copper-smelting are composed mainly of copper (usually greater than 35 per cent.), iron and sulphur, the remaining elements being usually in proportions sufficiently small to allow of their treatment as impurities, rather than as essential constituents of the mattes. In modern practice of smelting copper-ores in blast-furnaces the tendency is to approach pyritic smelting as nearly as pos¬sible, the furnaces being low and the air supplied being largely in excess of that required for complete combustion of the carbonaceous fuel. Hence the atmosphere of the blast-furnace thus used is usually oxidizing or Dearly neutral? and, as a consequence, the reduction of metallic iron that was a necessary evil of former practice is of unusual occurrence in operations where the main object is the recovery of copper. Hearth-accre-

Nov 1, 1905

By Allen V. Heyl

This old district is a major zinc and lead source and minor copper and barite source. Ores are chiefly in the Galena Dolomite and in limestones and dolomites of the Decorah and Platteville Formations, all of Middle Ordovician age. Locally, deposits have been mined from Lower Ordovician dolomites and Upper Cambrian sandstones. Small deposits of lead, zinc, and iron sulfides have been found in Upper Ordovician Maquoketa Shale and in Lower and Middle Silurian Edgewood, Kankakee, and Hopkinton Formations. No post-Precambrian igneous rocks are known in the region, and the granitic and metasedimentary Precambrian basement rocks unconformably underlie the district at depths of 1500 to 2000 feet. The strata are gently flexed and faulted, probably largely the result of gentle compressive and rotational adjustments in the underlying crystalline basement, especially along lineaments between basement blocks. Folds of three orders ·of magnitude are recognized, and many related reverse, strike-slip, and normal faults of small to moderate displacements are present. Zinc-lead deposits are commonly linear, arcuate, or elliptical in plan. Most ore occurs as vein fillings in fractures and as breccia fillings and lining vugs, but some is in bedded replacements and impregnations of wall rocks. The ore is in shears, small reverse and bedding- plant faults, joints, and solution-slump structures related to intermediate and small folds. The main primary minerals in their general sequence of deposition are quartz, illite, dolomite, pyrite, marcasite, cobaltite(?), sphalerite, galena, chalcopyrite, millerite, barite, and calcite. Wall-rock alterations include solution of the carbonate rocks, silicification, dolomitization, clay alteration, and sanded dolomite. Oxygenisotope, trace-element, lead-isotope, and sphalerite- stratigraphy studies are in progress. Fluid inclusions in sulfide and gangue minerals are filled with concentrated brines at 120° to 40°C. Sulfides are directly replaced by supergene minerals above the water table at 50 to 100 feet in depth. In this relatively cool climate and limestone environment, smithsonite is in pseudomorphs after sphalerite; solution transport and redeposition of supergene minerals are rare. Ore genesis is postulated by rising hot-water solutions-a mixture of heated connate, magmatic, and meteoric waters.

Jan 1, 1968