Search Documents

By Richard Birk

Rf sputtered quartz has been successfully used in multilayer interconnects for MOS devices. The target potential was 2000 v peak to peak with a frequency of 13.56 Mc per sec. The sputtering rate was approximately 60A per min with an operating pressure of argon gas at 10 to 15 p. The dielectric strength is 8.0 x 10' v per cm and the pinhole density is less than 2 x 10-2 per sq mm. Infrared absorption peaks for the Si-O vibrational bands we at 9.4, 12.4, and at 22.5 p. The etch rate of the sputtered SiO2 is 1200A per min. MOS devices have been fabricated using multilayer interconnects with no degradation of electrical characteristics. MULTILAYER interconnects require an insdating film between the metal layers which can be deposited below any potential eutectic temperature. Sputtered Si4, which can be deposited with substrate temperatures below 200°C, satisfactorily meets the multilayer insulation requirements and has been used to prepare MOS circuits with multilayer interconnects. The physical and electrical properties of rf sput-

Jan 1, 1969

By Michael Hoch, Michel Desjardins

The isothermal section of the Mo-Ti-Zr-0 system at 1500°C was investigated using X- ray diffraction and mefallographic techniques. Up to 66.7 at. pct 0, the system contains ten four -phase regions. Isopleths at 10, 30, 45, 55, and 60 at. pct 0 were constructed. THE purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of molybdenum, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct o. PREVIOUS INVESTIGATIONS The Ti-Zr-0 system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by Hansen' and Levin, McMurdie, and Hall.3 Farrar, Stone, and Margolin studied the titanium-rich corner of the Ti-Mo-0 ternary. MATERIALS The titanium powder, 99.6 pct pure, the zirconium dioxide, and the molybdenum powder were supplied by the Fairmont Chemical Co. The zirconium powder,

Jan 1, 1962

[†Aaronson, Alfred E., Oil Producer, Pres., Tuloma Oil Cc Tulsa, Okla. '18 ¦Abad, Leopoldo F., College of Min., Univ. of California Berkeley, Cal. '23 ¦Abadilla, Quirico A., Geol. Dept., Cia. Mexicans de Petroleo "EI Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio, Tampico, Tamps., Mexico. '20 ¦Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, 0. '21 Abbott, Clarence E., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala. '04] [ ]

Jan 1, 1925

By J. L. Weeks

THERMAL conductivities of several samples of uranium and uranium alloys were determined using an apparatus previously described.' The value previously reported for uranium,' 0.035 cal per sec per cm per "C at 70°C, is in error due to the failure of a thermocouple during the determination on uranium. The defective thermocouple was detected after a reanalysis of the data obtained during the run and since has been replaced. Subsequently, runs on several samples of uranium show the thermal conductivity of uranium to be 0.069 cal per sec per cm per 'C at 70°C. The accuracy of the determinations was checked by measuring a sample of synthetic sapphire whose thermal conductivity was previously reported and found to be in agreement with other values."-" The values given in Table I are believed correct to % 3 pct or 0.003 cal per sec per cm per "C, whichever is larger. The samples were provided by J. H. Kittel of the Argonne National Laboratory, Metallurgy Div. References J. L. Weeks and R. L. Seifert: Apparatus for the Measurement of the Thermal Conductivity of Solids. Review of Scientific Instruments (1953) 24, pp. 1054-1057. J. L. Weeks and R. L. Seifert: Note Regarding the Thermal Conductivity of Synthetic Sapphire. Journal American Ceramic Society (1952) 35, p. 15. :' J. Francl and W. D. Kingery: Thermal Conductivity: IV, Apparatus for Determining Thermal Conductivity by a Comparative Method; Data for Pb, Al2O3, BeO, and MgO. Journal American Ceramic Society (1954) 37, No. 2, Part 11, pp. 80-84. (Part 11: special issue on thermal conductivity.) ' W. D. Kingery, J. Francl, R. L. Coble. and T. Vasilos: Thermal Conductivity: X, Data for Several Pure Oxide Materials Corrected to Zero Porosity. Journal American Ceramic Society (1954) 37, No. 2, Part II, pp. 107-110. (Part 11: special issue on thermal conductivity.) Edwin Ruh: New Jersey Ceramic Research Station, Rutgers University. Private communication.

Jan 1, 1956

CORPORAL SHEPPARD B. GORDY Sheppard B. Gordy, a brief biography of whom was printed inn the January Bulletin, entered the employ of the Braden Copper Co. immediately on his graduation from the Sheffield Scientific School in 1912. He remained with this company four years, working up through the various grades to assistant foreman and foreman to one of the individual mines. The last year he was in its employ, he acted as general mine foreman. He was for a short time with the Chile Exploration Co. and then went with the Andes Exploration Co. (Anaconda) and remained with CORPORAL SHEPPARD B. GORDY. the latter, doing mine exploration and development work, until he sailed for home in June, 1918, to give a more personal and active service to his country in her need. He declined a tender of induction into an officers' training camp, at the urgent request of Professor McClelland supplemented by Mr. Potter, because they demonstrated to his satisfaction that he could give more valuable service to his country in helping out with the aircraft production. Being within the draft age, in order to carry out this plan, it was necessary for him to be called by his Local Board and sent to camp. This call came Aug. 26. Two weeks before that time lie had gone to Dayton, Ohio; to begin the study of aircraft production, and was sent by the Dayton Board to Camp Sherman, Chillicothe, Ohio, where he died of pneumonia on Oct. 9.

Jan 3, 1919

By G. V. Kurdjumou

STAFF: Editor, Gerhard Derge Acting Editor, Paul G. Shewmon Carnegie Institute of Technology Schenley Park Pittsburgh 13, Pa. Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Karl L. Fetters, President; J. S. Smart, Jr., Past-President; R. C. Cole, Vice President; R. L. Hennebach, Treasurer; R. W. Shearman, Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: W. 0. Phil-brook, Chairman; H. L. Bishop, R. C. Cole, J. N. Hobstetter, W. A. Krivsky, E. R. Morgan, F. C. Langenberg, R. E. Lund, Paul Queneau, L. L. Seigle, R. L. Smith, and T. V. Wainwright. Review and selection of manuscripts is under the supervision of the following Publications Committes: Extractive Metallurgy Division: R. E. Lund, Choirmon; M. E. Wodsworth, Vice Choirmon; D. H. Boker, Jr., G. M. Bell, R. E. Grace, W. A. Krivsky, R. A. Lewis, Chorles O'Neill, A. W. Schlechten, R. E. Shinko~ke~, and W. W. Stephens. Iron and Steel Division: T, V. Wainright, Choir- mon; ti. L. Bishop, R. E. Boni, T. E. Doncy, D. W. Murphy, Johonnes M. Uys, J. B. Wogstaff, ond R. G. Word. Institute of Metals Division: J. N. Hobstetter, Choirmon; P. A. Beck, J. J. Beckar, G. F. Boiling, J. O. Brittain, J. 0. Clark, R. 5. Davis, A. E. Dwight, R. W. Fountain, L. R. Girifolco, J. C. Gurlond, H. S. Kolish, E. L. Harmon, J. J. Heger, A. A. Hendrickson, L. Himmel, J. P. Hirth, H. H. Johnson, Jr., R. R. Nosh, T. N. Rhodin, R. H. Richrnon, H. C. Rogers, W. Rostoker, O. Sherby, C. W. Spencer, L. Slifkin, J. K. Stanley, R. Steinitz, H. C. Stumpf, ond R. Swolin. PuUlished bimonthly by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street, New York 17, N. Y. Telephone PLaZa 2-6800. Subscription $30 peryear for non-AIME members in United States and North, South, and Central America; $32, foreign; $30peryear$7.50 for AIME members. Single copies, $6.00, single copies foreign, $6.50. The CentralAmerica;AlME is not responsible for any statement made or opinion expressed in its publications ... Copyright 1962 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . .Copyright.Registered cable address, AIME New York . . . Indexed in Engineering Index, Industrial Arts Index, and Chemical cableaddres .. . AlME class postage paid at New York, N. Y., and Ann Arbor, Mich. Volume 224, Number 3.

Jan 1, 1962

By E. N. Harshman

Uranium mining and milling are rather new industries in Wyoming and South Dakota, but, in the past 15 years, ore valued at more than $400,000,000 has been mined and milled in the region. The major uranium deposits are in structural and/ or erosional basins or on the flanks of uplifts. The principal host rocks are medium- to coarse-grained sandstones that were deposited in continental or brackish-water environments and were derived in large part from the granitic cores of the uplifts and the sedimentary rocks that flank the cores. The ages of the host rocks range from Cretaceous to Miocene, but more than 95 per cent of the known reserves in the region are in rocks of early Eocene age. The bulk of the ore in the region is unoxidized and lies below the water table; some oxidized ore has been mined in the Powder River Basin and Black Hills districts. The unoxidized ore comprises pyrite, uraninite and/ or coffinite, marcasite, hematite, jordisite(?), and selenium. Minerals in the oxidized ore include hydrous uranium carbonates, phosphates, and sulfates and hydrous uranium and/ or vanadium silicates. The deposits are in the form of ore rolls that contain from a few hundred to a few hundred thousand tons of ore, ranging in grade from 0.1 per cent to 1.0 per cent U3O8. The rolls are at the margins of large tabular bodies of sandstone that has been altered by the orebearing solutions. The deposits are believed to have resulted from the interaction of an alkaline; oxidizing, ore-bearing ground water and a reducing environment. Exploration guides include the spatial relations of ore to altered sandstone, favorable lithology in the host rock, the content of certain elements and/ or compounds in ground water, and the relation of deposits to major paleodrainages.

Jan 1, 1968

By E. L. Tucker

PREVIOUS investigations of E. L. Tucker and R. E. Head' related in particular to the effect of cyanogen compounds on galena, sphalerite, and pyrite, and their behavior in the presence of such com- pounds. The present contribution deals with the float- ability of the copper minerals and of pyrite. All experiments were performed on minus 200-mesh material, the method of preparation being the same as that described in the previous article. Flotation tests were made in a small mechanically agitated machine of 50-g. capacity designed in this laboratory by Gates and Jacobsen." General Naval Stores pine oil No. 5 and potassium xanthate were used in constant amount in all of the experiments; these agents were selected because of their present wide use in the flotation of copper minerals. Lime additions were varied to secure four 'final hydrogen ion concentrations, namely, neutral, 0.0005 per cent CaO, 0.003 per cent CaO, and 0.02 per cent CaO. The variation in lime addition was introduced to include the range of alkalinities employed in actual flotation practice.

Jan 1, 1926

By A. W. Bethune, L. M. Pidgeon

The equilibrium vapor pressure of zinc has been determined over the systems: ZnS(s) + Fe(s) = FeS(s) + Zn (vapor) and ZnS(s) + 2Cu(s) = Cu2S(s) + Zn (vapor) by reacting the components in an evacuated tube containing a thin copper fiber, and allowing equilibrium to be established with respect to the brass formed and the zinc in the vapor phase. The composition of the brass formed was determined and equilibrium vapor pressure values obtained from existing data. Between 850' and 1000°C, values for the first reaction ranged from 8 to 58 mm Hg; for the second reaction from 1.8 to 22 mm Hg. THE direct reduction of metallic sulphides may be indicated by an equation of the form MS + X = XS + M [1] where X is some suitable reducing agent. In the case where M is a metal of relatively high volatility, the use of vacuum will displace the equilibrium to the right at comparatively low temperatures in the face of the usually unfavorable thermochemistry. For this technique to be feasible, MS, X, and XS, must of course be nonvolatile compared to M. In this regard, zinc becomes an obvious metal both from the point of view of its volatility and the fact that most commercial ore deposits of this metal occur as the sulphide, and its direct reduction would avoid the expensive roasting process necessary prior to present day reduction methods. Two reducing agents are of interest, namely copper and iron, with the former having the added attraction of being relatively easily regenerated by oxidation in the copper converter. The possibility of these reactions has been considered before. Imbert1 patented a process whereby zinc sulphide was reduced by either copper or iron. The process as described took place at atmospheric pressure and, at the high temperatures required, the system was molten, resulting in the formation of a matte with the consequent reduction in the activities of the reactants. Peterson2 did further experimental work on these reactions and, although promising results were obtained on a small scale, attempts to increase the size of the furnace led to excessive "blue powder" formation. The early workers failed to realize the large reduction in temperature afforded by the use of vacuum and its desirable results. More recently, the direct reduction of zinc sulphide by iron has been the subject of a thermody-namic investigation by Kelley,3 and Gross and War-rington' have studied the kinetics of the reaction in the temperature range 900" to 1000°C, their experiments being conducted using vacuum and indicating that the reaction would proceed practically to completion in 1 to 3 hr, depending on the temperature. A qualitative examination of the system ZnS-Cu carried out at this University indicated that 98 pct of the theoretical zinc in the charge could be recovered in 1 hr at 1000°C when operating under reduced pressure. The purpose of this research program was to study the equilibrium of the two reactions. During the investigation, reference to the experimental work of Schenk5 was found but, due to lack of detail in the report, it was felt that it would be desirable to continue the equilibrium measurements. Selection of Method The measurement of vapor pressure of metals presents obvious problems resulting from the high temperatures which must be employed. In the present case, the production of the "reaction pressure" introduces a further difficulty since a chemical reaction must proceed before any metal vapor pressure is produced, resulting in depletion of the re-

Jan 1, 1954

By A. Gemperle

Electron diffraction and transmission electron microscopy on foils at room temperature were used to investigate the ordering of Fe-Si alloys containing 10 to 23 at. pct Si. A certain degree of DO3 order was found in all alloys. With the exception of the lowest silicon concentration for which the antiphase domains could not be clearly resolved, the alloys have a domain structure of two-domain type with boundaries having 1/4a01<111> displacement vectors for less than 12.3 at. pct Si and with boundaries having 1/2 a0<100> displacement vectors for more than 12.3 at. pct Si. The alloys with 12.3 at. pct Si have a domain structure consisting of fine domains with 1/2a&apos;o<100> boundaries within much larger domains with 1/4a&apos;o<111> boundaries. The development of these structures can be explained by transition of the alloy from the disordered state into the B2-type order and then into the D03-type order by the mechanism proposed previously for the FeSAl alloys. The existence of the B2 structure in the lower part of the investigated concentration range reported in some articles can be explained by fine domains with 1/2a&apos;o<100> boundaries formed by several disordered planes within large domains with 1/4a&apos;o<111> boundaries. The ordered structure predicted by the theory —with practically no domain boundaries —is found in the alloys having 12.3 at. pct Si where it develops in the B2 structure region. ORDERING in Fe-Si alloys was first studied by phragmenl who found that beginning with 13 at. pct Si the DO3 (Fe3Si) superlattice reflections appear in the diffraction patterns. The equilibrium diagrams constructed later by corson2 and Haughton3 from various measurements proposed the existence of a homogeneous solid solution (a phase) in the range from 0 to 25 at. pct Si. Jette and Greiner4 and Farquhar et al.5 measured the relation between lattice parameter and composition and they considered the break in the curve at 9 to 10 at. pct Si to be caused by the ordered solution a"(Fe3Si). Glaser and Ivanick6 Determined critical ordering temperatures of the alloys containing from 10.9 to 27.9 at. pct Si from the measurement of the electric resistivity of quenched samples. In all cases the critical temperature was lower than the melting point and it was highest for 25 at. pct Si. Lihl and Ebel7 measured the lattice parameter curves at various temperatures up to 1000°C. The region between two breaks on these curves, corresponding to 10 to 12.5 at. pct Si at room temperature, was considered by them to be two-phase (a + a"). They concluded by extrapolation of the measured values that a" in the alloy having 25 at. pct Si is stable up to the melting point. Davies8 studied superlattice reflections in the X-ray diffraction patterns of an alloy containing 8.7 at. pct Si. He found the B2 structure and short-range order in the slowly cooled samples and the DO3 A. GEMPERLE is Research Scientist, Institute of PhysicS, Czechoslovak Academy of Sciences, Prague, Czechoslovakia. __Manuscript submitted January 2, 1968. IMD structure in the quenched and annealed samples. This investigation first reports the presence of the B2 structure, phase a&apos;: in Fe-Si alloys. Meinhardt and krisement9,10 also found its existence in Fe-Si alloys by neutron diffraction. No order was detected by them in the alloy containing 8 at. pct Si. The onset of B2 order was observed at a composition of 9.2 at. pct Si. They found almost perfect B2-type order with partial DO3-type order at room temperature in the 10 to 12.5 at. pct Si range and almost perfect DO3-type order in the 12.5 to 25 at. pct Si range. They established the critical temperatures Tc of both the structures through measurement at higher temperatures. The critical temperature for the B2 structure was found to be always higher than the critical temperature for the DO3 structure of the same alloy. They extrapolated the curves of the critical temperatures and concluded that the alloys with more than 17 at. pct Si have the B2 structure up to the melting point and the alloys with more than 23 at. pct Si have the DO3 structure up to the melting point. The results of Meinhardt and krisement9,10 were confirmed by Dokken&apos;s measurement" of the temperature dependence of the electrical resistivity in the 10.8 to 15 at. pct Si range. On the other hand chessin12 detected by X-ray diffraction a considerably lower degree of order in the 12.7 at. pct Si alloy. ANTIPHASE DOMAIN STRUCTURE IN ALLOYS WITH B2- AND DO$-TYPE ORDER The ordered structures B2 and DO3 can be described in terms of a subdivision of the bcc lattice into four fcc sublattices with a parameter double that of the bcc lattice. Following Marcinkowski13 we will label them I. 11, 111, IV. The B2 structure in the AB alloy is formed by placing A atoms on sublattices I and II and B atoms on sublattices III and IV. In a non-stoichiometric perfectly ordered alloy having concentration (A) > (B), A atoms occupy sublattices I and 11. and A and B atoms distributed at random occupy sublattices III and IV. The DO3 structure in an A3B alloy is formed by placing A atoms on sublattices I, 11, and 111, and B atoms on sublattice IV. In a nonstoichiometric, perfectly ordered alloy having concentration (A)/3 > (B), A atoms occupy sublattices I, 11, and 111, and A and B atoms distributed at random occupy sublattice IV. As further shown in Ref. 13, two types of domains are possible in the B2 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4 a&apos;o<ll1> only. Four types of domains are possible in the DO3 superlattice and the antiphase domain structure has associated with it boundaries with displacement vectors 1/4a&apos;o<111> and 1/2a&apos;o<l00>. Bethe14 suggested on the basis of theoretical considerations that in a structure with two sublattices at low temperatures only one domain should be present in the whole crystal at equilibrium. Similarly Bragg15 concluded that at low temperatures the domain struc-

Jan 1, 1969

By AIME AIME

The Washoe plant, 1 in Anaconcla. Mont., together with the local street-railroad, ranches a. foundry and machine-shop a brick-plant and the Montana hotel, form a property under one management; to which should be added the mines in Butte owned by the company, from which part of the ore-supply of the plant comes. The Anaconda Copper Mining Co., controlled by the Amalgamated Copper Co., was reorganized under the laws of Montana in 1893. A map of the plant, showing the numerous departments and illustrating the details of tracks, pipe-lines, and charging-stations for compressed-air locomotives, is given in Fig. 1.

Jul 1, 1906

By L. Adler

Any design of a mine roof in bedded deposits which ignores differential deflections at the supports can quickly lead to dangerous overstressing. As illustrated by the typical case presented on page 1029, if one support deflects only 0.1 in. more than its neighbor, stresses 50 pct higher than anticipated will result. Previous studies1-3 have assumed that the mine roof acts like a beam clamped at both ends, with no deflection or slope&apos; at the supports (Fig. 1). Essentially this assumes:5* ?A = ?, = ?b and dA = dB = 0. However, a host of conditions can cause differential sag or deflection at one support, and even an apparently trivial deviation can have major consequences in the beam: variations in spacing, size, and material of supports; local settlement due to floor heaving or lower mine openings; non-uniformity in wedging or bolt tensioning.8 In one particular instance concrete pillars, poured in place, shrank away from the roof upon setting.&apos; When understood and controlled, differential sag becomes a definite advantage, permitting the transfer of loads from one support to another. Where one support is a bolt or prop and the other a pillar or rib, the load on the former can be reduced while the load on the pillar or rib is increased. This means two things: 1) savings can be effected by using smaller artificial supports such as props and bolts and 2) loads can be increased in the rib to induce eventual failure for longwall caving. In this last respect, another factor underlying coal bumps becomes understandable. The design of a mine roof by beam theory assumes that when a bedded formation is homogeneous, iso-tropic, and elastic, it will act like a uniformly loaded beam, fixed or clamped at both ends,6 s in Fig. 1.&apos;" These are important assumptions. The uniform load is the weight of the beam itself or its body load. For a beam of unit width, this load becomes per foot: w = yhb. w = uniform load y = specific weight, lb per ft3 h = depth or thickness of beam, ft b = width of beam, ft Since b = 1, w - yh [ 1 ] A beam fixed at both supports is statically indeterminate to the second degree, that is, two equations in addition to those for static equilibrium are required to determine the reactions at the supports. These equations result from the geometry. From statistics: ^F,= 0;RA + RB — wL = 0 [2] wU S,M0 = 0 ; MB H------------MA — RBL = 0 [3] it Using superposition in which the left support is kept intact and the right one resolved into an active force and moment, we obtain from Fig. 2:" ?b = ?m + ? b2 + ?B3 = 0 dB = dB1 + dB2 + dB3 / wU Ma RBL \ V d°=(-r+-2—r)-zr [5] Where: Subscripts refer to position on axis of beam R = force, lb M = moment, ft-lb w = uniformly distributed load, lb per ft L = span, ft 0 = slope, radians d = deflection, ft E = Young&apos;s Modulus, lb per ft" 1 = Moment of inertia about the neutral axis, ft4 Solving Eqs. 2 through 5 for the four unknown reactions, we obtain: 2 L3 Fig. 3 is obtained by plotting MA and M, vs d, and then plotting RA and R, vs d, and adjusting their scales to coincide with MA and M, vs d,. It should be noted in Eqs. 6 and 7 that as dB increases, MA increases the same amount that Mn decreases. Eqs. 8 and 9 show a similar relationship between RA and R,. Proof that MA is the maximum absolute moment occurring in the beam is as follows: where M, = moment at x wx-When where M,., = maximum positive moment Eqs. 6 and 8 into above: For small dn: MA> M,,,

Jan 1, 1960

By William D. Southard, Joseph W. Schlitt, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott &apos;s Bingham Canyon copper precipitation plant, one of the world&apos;s largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12-15% moisture could be consistently delivered for smelting.

Jan 1, 1980

By M. D. Banus, M. B. Bever, A. K. Jena

Measurements of the heat effects on addition of various solid phases of InSb to a solution calorimeter have confirmed the existence of a new high-pressure plzase InSbQII), which was jormed at 37 kbar and 623°K. The heats of formation of InSbQ), InSbfl), and InSb(111) have been measured and the heats of transjormation of InSb(1) to InSb(1l) and InSb(Iii) and of &apos;InSb(ll) to InSb(iiI) at atmospheric pressure and 78°K have been determined independently. Other thermodynamic properties of these phases, the phase boundary InSb(i)/InSb(ll), and the relative positions of the triple points are calculated. The pressure-Dolume term is shown to be more critical than the internal energy difference in making the phase InSbQ) less stable than InSb(II) at high pressures. Observations on partially transformed specimens suggest that the transformation of&apos; metastable InSb (III) takes place in the two steps InSb(lll) — InSbQI) and InSbQI) — InSb(l). The compound InSb can exist as several phases depending on the temperature and pressure. The phase InSb(I), which is a semiconductor having the zinc-blende structure, transforms into the phase InSb(11) at a pressure of about 23 kbar and room temperature.&apos;-3 The phase InSb(II) has the 6 tin structure,4-6 is metallic, and becomes a superconductor below 2.lok7 An orthorhombic phase of InSb has been reported to occur above a pressure of approximately 30 kbar at room temperature.&apos; This phase is also a superconductor below about 3.4k9 The phase InSb(I1) is retained at atmospheric pressure if it is quenched to 78°K under pressure,6,7 but tends to transform at higher temperatures and does so explosively above approximately 210ok,7 A value of the heat of transformation of InSb(1) to InSb(II) at 210°K and atmospheric pressure has been reported.&apos; A concurrent publication&apos;0 reports evidence for a new solid phase InSb(III), which was formed by annealing InSb above 58 1°K at 37 kbar, above 560°K at 52 kbar, and above 473°K at 65 kbar. Specimens of InSb(II1) had a superconducting transition temperature of 4.lo ± 0.1oK. X-ray diffraction patterns also indicated the presence of a new phase. In this communication, thermodynamic properties of the phases InSb(I), InSb(II), and InSb(II1) are reported and discussed. The phase boundary InSb(I)/InSb(II) and the relative positions of the triple points are calculated. 1) EXPERIMENTAL 1.1) Preparation of Specimens. Specimens of the high-pressure phases of InSb were prepared in a belt-type high-pressure chamber by a tichnique described in detail elsewhere.&apos;&apos; Charges of 0.6 to 0.8 g of Cominco semiconductor grade InSb were used. The temperatures were measured with a chromel-alumel thermocouple, the hot junction of which was within 0.5 mm of the specimen. The specimens were heated under a pressure of 37 kbar for 1 hr at 723°K (which is well above the liquidus) and quenched to room temperature. One set was annealed at 523°K and another set at 623°K for 20 to 24 hr. These annealing temperatures were chosen because 523°K was below and 623°K was above the temperature of the transformation of InSb(II) to InSb(1Tl) at 37 kbar.10 The specimens were then cooled to 125°K by passing liquid nitrogen through the jacket of the belt die before the

Jan 1, 1968

By J. D. Hanawalt

Significant strides were made in the year 1948 leading to further recognition of the place of magnesium as a common commercial metal, rather than as just a premium aircraft material. One of the factors contributing to this recognition was the price stability and, in many cases, price reduction of magnesium products in 1948. In contrast to most other metals, manufacturing advances in magnesium outweighed the effects of increased labor and other costs. At the present time, many magnesium extrusions, die castings, and permanent mold castings can be purchased as cheaply as their aluminum counterparts in these forums, though competitive prices for sheet still await the inauguration of a modern tandem rolling mill for magnesium, such as has already been demonstrated.

Jan 1, 1949

By Dean S. Rogers

The conventional role of exploration, development and grade control is examined in this paper within the context of the many and varied types of gold occurrences which are found at the Dome Mine. The account endeavours to trace the development of the total ore evaluation process, from diamond drilling through the exploration and drifting stage, to the stope development and planning phase of the operation, with an emphasis on sampling techniques and assaying procedure. The concept of ore reserve calculations is developed and the practice of grade control is described. In summary, the role of the geological, the engineering and the mining department is presented in relation to the contribution each has to make in the evaluation and exploitation of ore from one of the world&apos;s classic Archean gold deposits.

Jan 1, 1985

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield-point of 16,000 lb. for pure electrolytic iron, one reaches a -maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated Yensen observed an enormous drop in elongation and area reduction at about 2.65 per. cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to. 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

By Westwater, J. S.

The Mather mine of The Negaunee Mine Co. embraces nearly all of Sections 1 and 2, T47N, R27W. within the limits of the cities of Negaunee and Ishpeming on the Marquette iron range of Michigan&apos;s Upper Peninsula. Operations of the Negaunee Mine Co., the stock of which is jointly owned by Bethlehem Steel Co. and The Cleveland-Cliffs Iron Co., are under the direction of the latter company. The opening of the Mather mine was described by C. W. A1len. Mather "A" shaft was completed to an initial depth of 2352 ft in early 1943. The shaft capacity of over one million tons yearly is in prospect of being realized by orderly development and mining, and sinking of the second or "B" shaft then started in accordance with previous planning. Mather " B, " also a vertical shaft, was designed as a twin to Mather "A" shaft and the sinking technique developed at Mather "A" was utilized in "B" shaft operation.

Jan 1, 1949

By W. Joseph Schlitt, William D. Southard, Bruce P. Ream, Lawrence J. Haug

The operation of Kennecott&apos;s Bingham Canyon copper precipitation plant, one of the world&apos;s largest, is described. This description includes a brief historical review of precipitation at Bingham and the general layout and operation of the present cone cementation facility. Current practices are based on results of studies undertaken to define improvements needed in each unit operation. These improvements were required to meet changing plant conditions and were implemented primarily within the constraints of the existing facilities. Specific unit operations included were the cone precipitators, the cone discharge thickener, the cone effluent settling basins, and the plate and frame filter presses. As a result of these improvements, loss of precipitated copper decreased and the degree of precipitation increased, raising copper recovery by 9 t/d. At the same time, iron consumption was reduced by 22.5 t/d. Problems in drying the cement copper were also overcome so that a product containing 12 - 15% moisture could be consistently delivered for smelting.

Jan 6, 1979

By Wilbur S. Burbank, Robert G. Leudke

The impressive western San Juan Mountains of Colorado were carved by Pleistocene and Recent erosion from a thick blanket of Tertiary volcanic rocks that rests upon a basement of metamorphic, sedimentary, and igneous rocks ranging in age from Precambrian to Tertiary. These rocks record a long, complex, and fairly complete sequence of geologic events that have affected the region through much of geologic time. The geologic history of the region includes several periods of deformation, erosion, and igneous activity; closely associated with two of these periods were two periods of mineralization. The older of these was related to Late Cretaceous-early Tertiary (Laramide) intrusive activity, and its deposits occur in the older sedimentary units. The younger, of later Tertiary age and related to the widespread middle Tertiary extrusive and intrusive activity, is the chief concern of this paper. Tertiary volcanism built a great plateau surrounding the San Juan volcanic depression, a complex of subsided crustal blocks in the vent areas. The Silverton and Lake City cauldrons, nested within the larger depression, were domed by resurgent magma that created keystone grabens along the distended crests of the domed floors and many postcauldron radial and concentric fractures, dikes, and intrusive plutons within and marginal to the cauldron sites. The postvolcanic evolution of large quantities of gases, chiefly carbon dioxide and water, propylitically altered the rocks in and around the volcanic depression prior to the younger period of ore deposition. The ore deposits, localized mainly in the radial and concentric fractures about the cauldrons and in the associated graben faults, include fissure veins, chimneys, replacements, and disseminations in volcanic and underlying basement rocks. Fissure veins, constituting the major economic source, yielded precious- and basemetal ores. Most veins are compound with sphalerite, galena, and chalcopyrite; some veins contain silver-bearing arsenical sulfosalts and free gold. These minerals occur in predominantly quartz gangue. However, gangues composed of several manganese silicates and carbonates and relatively· barren of metals are abundant locally and probably originated by alteration of rocks at roots of faults and fissures during evolution of carbonatic solutions. The bulk of the ores are hypogene and probably had their source in deep parent magmas of the shallow eruptive rocks. Total production since the early 1870's has exceeded half a billion dollars in recovered metals, with a ratio of precious- to base-metal values of about 3 to 2. Since 1930, improvements in metallurgical treatment and mining techniques have increased the base-metal yield.

Jan 1, 1968