Search Documents

By Frederick Laist

I. EXPERIMENTAL FLOTATION CONCENTRATION INTRODUCTION EARLY in 1914 it was decided to test, on a fairly large scale, the treatment by flotation of Anaconda slime and mill tailing. For this purpose a standard-type Minerals. Separation machine was installed at the Washoe Reduction Works during May and June, 1914. This was followed by the. installation of a full-size Callow pneumatic machine plant. Experiments were also made, on a smaller scale, with the Froment, the Towne, the Fields, and the Anaconda flotation machines. The last-named machine was developed at this plant. In addition to the tests made in the standard-type Minerals Separation machine some tests were made using a Minerals Separation machine of the sub-aeration type. During the series of experiments a large variety of oils was tested. Experiments were also conducted using both round-table feed and tailing to determine whether it would be better to displace the round tables by flotation for the treatment of the slime, or to supplement the round tables by flotation of the round-table tailing. A series of tests was also made on the treatment of the mill tailing by grinding followed by flotation to determine the relative merits of flotation and leaching for the treatment of this product. In addition, flotation tests were made on mixtures of mill tailing and slime. The round-table feed referred to above is the total slime from the mill. It contains about 35 per cent. colloidal solids and approximately 90 to 95 per cent. of the total solids will pass through 200 mesh (0.067 mm.). It assays from 2.3 to 2.6 per cent. Cu. The mill tailing referred to above is the total discard from the mill, exclusive of the slime. It is all finer than 2 mm. and about 90 to 95 per cent. will remain on 0.25 mm. It assays about 0.60 per cent. Cu. A brief summary of the experimental flotation results follows:

Jan 3, 1916

By V. R. Garfias

Principal events in petroleum operations of Mexico during 1934 have been the completion of three producing wells in the Poza Rica area and the plans for the expansion of operations of the Cia. de Petroleos de Mexico, S.A. (Petromex). Production for 1934 is estimated at close to 38,000,000 bbl., an increase of 4,000,000 bbl. over the previous year; an increase due in large part to the successful development in Poza Rica. The output of the South fields (Golden Lane) and Tehuantepec fields also increased somewhat during the year. Production of natural gasoline increased from 382,000 to 431,000 bbl. in 1934. Crude run in local refineries is estimated at 26,000,000bbl., some4,000,000bbl. more than the previous year. Exclusive of bunker fuel exports totaled 24,000,000 bbl., or 3,000,000 more than in 1933. Domestic consumption increased approximately 500,000,bbl. during the year, reaching a total of close to 13,600,000 bbl., exclusive of ships' bunkers. A total of 148 wells were completed as compared to 91 in 1933 and 40 in 1932. In proven areas, 133 completions resulted in 54 producers and 79 failures. The 15 wildcats drilled during 1934 gave no encouraging results. Seven of these were located in the border zone of northeastern Mexico; three tested possible northeast extensions of the Northern fields; two were drilled for possible extensions of the "Golden Lane" and three were completed in the Isthmus of Tehuantepec. Fields Northern Fields (Heavy Oil District).—There were 34 producing wells and 71 failures completed in the Northern fields, as compared to 20 producers and 20 failures in 1933. Practically all new producers were drilled to the shallower San Felipe formation, while wells drilled to the deeper Tamasopo limestone encountered salt water. Production of the field totaled 11,890,000 bbl., a decrease of 7.5 per cent from the previous year. Acid treatment was attempted during the year in seven wells

Jan 1, 1935

By L. H. Schwartz, S. K. Lahiri, M. E. Fine, D. Chandra

WHILE the yield stress of solution treated Fe-Cu alloys increases rapidly with aging, a precipitate has only been directly observed in overaged samples.'-" This precipitate is essentially pure fcc copper, the E phase. Hornbogen2 suggested that the initial hardening is due to clustering of copper atoms in a bcc iron matrix. Hornbogen was not able to obtain direct confirmation for such bcc clusters by either X-ray diffraction or electron microscopy; however, he did observe analogous clustering in Fe-Au alloys7 where the scattering factor difference between iron and gold is more favorable than that for iron and copper. Fujii, Nemoto, Suto, and Monma4 recently observed diffuse electron diffraction scattering in a 2.5 pct Cu alloy aged at 500°C: for 30 hr. They suggested that part of the diffuse SCattering was due to a modulated structure of 26 to 42 wavelength parallel to the (110) matrix plane. This disappeared with further aging. However, 30 hr at 500°C is well beyond the peak strengthening in this alloy which occurred at less than I hr at 500oc.4 By transmission electron microscopy they could not distinguish between quenched samples and samples aged to maximum strength. The purpose of the present investigation was to try to obtain further confirming evidence for a precipitation stage preceding the formation of the fcc E phase. Change in Young's modulus was selected for study be- EXPERIMENTAL PROCEDURE The Fe-1.67 at. pct Cu alloy was supplied by the U.S. Steel Corporation in the form of a hot forged rectangular bar. The carbon and nitrogen contents of this alloy were 70 ppm and less than 10 ppm, respectively. The samples for Young's modulus measurements were made by cold swaging to & in. diam and cutting to 2 in. lengths. Tensile test samples 1 in. long were prepared by cold rolling to a thickness of 0.012 in. and then machining to gage dimensions of 0.5 by 0.012 in. For Mijssbauer studies, foils 1 mil thick were prepared by cold rolling. During fabrication the alloy was given intermediate anneals at 845OC followed by quenching. The specimens after preparation were solution treated at 1000°C (y field) or 845°C (a field) for 1 to 2 and 5 to 6 hr, respectively, in a dynamic vacuum of about 2 x lom6 torr. The tensile and modulus specimens were drop-quenched into iced brine through an aluminum foil which vacuum-sealed the bottom of the furnace tube. The MOssbauer foils were drop-quenched into helium gas cooled by passing through N2 (liq) in a copper coil. The grain diameter of the modulus and tensile specimens was between 0.025 and 0.035 mm. The samples were aged from 400" to 500°C in a dynamic vacuum of 2 x 10-6 torr and cooled by pulling into a water-cooled portion of the vacuum system. The dynamic Young's modulus was measured at room temperature using electrostatic excitation and detection of longitudinal vibrations.' Neglecting any length change during the aging, (this is expected to be comparatively small), the fractional change of Young's modulus (?Et)/Eav, is equal to twice the fractional change of the resonant frequency (?ft)/fav . ?ft =ft —fo where fo and ft are the resonant frequencies of a specimen before aging and after aging to time t. The measured f's, approximately 51,000 cps, were corrected to 25°C for any variation in the ambient temperature. The tensile tests reported were carried out at room temperature in an Instron with a 1000 lb full scale load cell. The flow stress reported herein corresponds to a strain of 0.002. The Massbauer spectra were taken in a constant acceleration model AM-1 NSEC spectrometer. The

Jan 1, 1970

By C. R. Van Hise

PART I.-GENERAL PRINCIPLES. [ ]

Jan 1, 1902

By M. Bevis, A. F. Acton, P. C. Rowlands

Defor~nation twinning and transformation twinning modes most likely to be operative in Fe-Ni and Fe-Ni-C martensites have been determined using a new theory of the crystallography of deformation t~inning.~ This analysis shows that potentially important conventional and nonconventional twinning modes1 have been omitted in previous analyses. Discussion is given on the relevance of the predicted twinning modes to the lattice invariant shear associated with the martensite transformation in steels and to anomalous deformation twinning in Fe-Ni-C martensites. THE two most important criteria which appear to govern operative twinning modes in metallic structures1 are that the magnitude of the twinning shear should be small and that the twinning shear should restore the lattice or a multiple lattice in a twin orientation. The latter criterion ensures that the shuffle mechanism required to restore the structure in a twin orientation is simple. These criteria have been adhered to in the prediction of twinning modes2"6 in bcc and bct single-lattice structures with axial ratios in the range y = 1 to 1.09 as, for example, encountered in martensite occurring in steels. Refs. 2 and 3 in particular consider the martensite transformation in steels and the twinning modes in these cases relate to transformation twinning, and hence the lattice invariant shear associated with the martensite transformation. The list of twinning modes which can be compiled from these sources is incomplete and the ranges of magnitude of shear considered could be unrealistically small, particularly in the case of deformation twinning. The latter consideration is supported by the fact that twinning modes with magnitudes of shear large compared with the smallest shear consistent with a simple shuffle mechanism have been established in, for example, the single-lattice structure mercury7 and the multiple-lattice structure zirconium.&apos; In addition the anomalous deformation twins reported by Ftichrnan4 to occur in a range of Fe-Ni-C martensites still remain unexplained. It is clear that a comprehensive analysis of twinning modes likely to be operative in martensite In steels is required. The results of the application of a new theory of the crystallography of deformation twinningg to these structures are presented in this paper. The theory has been used to determine all shears which restore the lattice or a multiple lattice in a new orientation with magnitude of shear up to a required maximum. The orientation relationships between parent and twinned lattices are not restricted to the classical orientation relationships of reflection in the twin plane or a rotation of 180 deg about the shear direction. PREDICTED TWINNING MODES Twinning modes which restore all or one half of lattice points to their correct twin positions will be referred to as m = 1 and m = 2 modes, respectively. These modes are the most likely to describe operative modes in single lattice structures. The bcc m = 1 and m = 2 modes which have magnitudes of shear s in the range s < 2 and s < 1, respectively, have been given10 and are reproduced here in Tables I and 11. Detailed discussion of the crystallography of these modes and cubic modes in general will be discussed elsewhere (~evis and rocker, to be published). The four twinning elements Kl, &,ql,7)2 as well as the magnitude of shear s are given for each twinning mode, and the twinning modes are given in order of increasing shear. Two twinning modes are given in each row of the tables, the twinning mode Kl, Kz, ql, q2 and the reciprocal twinning mode with elements Kl = K,, Ki = Kl, q: = q2, and 17; = ql. The m = 1 and m = 2 twinning modes which describe twinning shears with small magnitudes of shear and simple shuffle mechanisms in bct crystals with -y = 1 to 1.09 are given in Tables I11 and IV, respectively. On increasing the symmetry of the tetragonal lattice to cubic, that is making y = 1, all modes listed in Tables 111 and IV must reduce to crystallographically equivalent variants of the modes given in Tables I and 11, respectively, or become twinning modes with both shear planes as symmetry planes in the cubic lattice and hence not considered in Tables I and 11. With the exception of this last type of mode only those tetragonal twinning modes which reduce to modes 1.1, 1.2, 2.1, and 2.2 of Tables I and I1 are considered in Tables 111 and IV. For values of y in the range -y = 1 to 1.09 the tetragonal modes and the corresponding cubic twinning modes have approximately the same magnitude of shear. The twinning modes listed in Tables 111 and IV are therefore by the criteria given above the most

Jan 1, 1969

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.&apos;s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

By Robert K. Waits

The resistivity, temperature coefficient of resistance, stability at 200°C, and structure of annealed Si-Cr films have been studied as a function of film cowposition. Colorimetric analyses of the films indicated 20 to 60 wt pct Cr over the resistivity range of 1 to 10-4 ohm-cm. Resistors were delinealed by photolithographic etching, contacted with aluminum, and mounted in TO-5 packages. The average temperature coefjicient of resistance, a, between 50" and 150°C is related empirically to the film resistivity, p, by a (ppm per °C) = -2900 - 1140 log p (ohm-cm). Near a resistivity of 3.5 x 10-3 ohm-ctn (30 at. pct Cr) , the temperature coefficient changes from positive to negative. The temperature at which the resistance maximum occurs increases with decreasing resistivity. The conduction mechanism between —196" and +360 C appears to have two components—an activated conduction dominating a1 lord chromium content and higher temperatures and a linearly temperature-dependent conduction dominating at high chromium content and low temperatures. Electron diffraction patterns showed the films to consist of Cr3Si and amorphous silicon. Resistors thicker than 150A typically drifted less than 0.6 pct after 5000 hr stor-age at 200°C. Resistors as thin as approxinzately 80°A that had a silicon overlayer showed similar stability. Such films had sheet resistivities of 10 kilohm per square and temperature coefficients near —600 ppm per "c. THIN-FILM resistors having sheet resistivities greater than 1 kilohm per square are required in many integrated circuit applications. A process for producing such resistors should be compatible with present circuit fabrication and packaging, including exposure to maximum temperatures of 300° to 570°C during contact alloying, die-attach, and ceramic package sealing. In addition, the resistors should have a low temperature coefficient of resistance and change less than 1 pct during storage at temperatures up to 200°C for 1000 hr or longer. Reports of work beginning in 1949 at Battelle Memorial Institute indicated that, among other materials, the silicides of chromium, Cr-Co, molybdenum, tantalum, and tungsten were worthy of further study as high-stability resistive films. Later work on Si-Cr films vacuum-deposited by flash evaporation from a tungsten boat1 led to the conclusion that Si-Cr had "excellent properties for development into high- stability ... resistive elements". More recently, Si-Cr films have been vacuum-deposited from a tantalum boat,2 from a BeO-coated tantalum boat,3 by flash evaporation from an electron-beam-heated tungsten Source,4 and by triode sputtering.5 This paper describes a study of Si-Cr films vacuum-deposited by electron-beam heating of Si-Cr alloys. Resistivity, temperature coefficient of resistance, stability at 200°C, and structure were studied as a function of film composition. EXPERIMENTAL PROCEDURE Film Deposition. Si-Cr sources were prepared by vacuum-melting pressed pellets of mixtures of powdered chromium (99.9 pct, -100 mesh, Lunex Co., Pleasant Valley, Iowa) and silicon (99.99 pct, -325 mesh, United Mineral and Chemical Co., New York). A permanent-magnet focused electron-beam gun having a water-cooled copper crucible was used to heat the pellet until complete melting occurred. The mixture was then kept molten for an additional 5 min. The alloy thus formed was used as the source material for Si-Cr film depositions using the same electron-beam gun. Pieces of semiconductor-grade silicon ingots were used as sources for silicon depositions. The films were deposited within a standard vacuum evaporator having an 18-in.-diam Pyrex bell jar, a liquid-nitrogen-cooled trap, and a Consolidated Vacuum Corp. 6-in. diffusion pump containing Dow Corning DC-705 pump fluid. The substrates were thermally oxidized* silicon wafers 2 to 2.5 cm in diam. The

Jan 1, 1969

By T. Suzuki

LABOR. conditions have finally caused rock-drilling machines to supplant hand drillers in the Japanese mining industry, and have encouraged this study. During a period of three years 25,000 tests were made on 67 different American, Japanese, and European rock drills, using, respectively, the Paynter testing machine, and drilling in granite and limestone. Recorded were: air consumption, speed of rotation, torque of rotation, foot-pounds of striking energy, air pressures, input horsepowers, and speed of rock penetration. The author expresses his views on the interrelation of these factors and offers theoretical support, as well, by formulas based upon the mechanics of impact. He discusses the different designs of the valves, cylinders, piston hammers and rotation devices involved in the different types of rock drills, with respect to their merits and defects and offers conclusions about the factors that should be considered in the new design of a superior rock drill. The author&apos;s mathematical demonstrations and arguments for a value of "best feed clearance" of the drill bit from the rock are based upon the hand-operated screw-fed type of hammer drill. Automatic feeds have not been considered in this paper except for the tests on one drifter with air feed, 10 air-feed stopers, and some hand-held blockholers. The following classes of drills, with one of each model, size, or type, were tested: 23 heavy drifters, 34 light drifters and hand-held drills, and 10 stopers. They represented the following makes and models: 40 from the United States—namely, Ingersoll-Rand 18, 148, L-74, 24-70, N-72, N-75, R-72, 26, BAR-33, BCR-430, DCRW-23, RA-12, CA-31, CC-11; Denver 7, 107, WT-21, WT-31, WT-331, WT-337 (models WT with motor rotation, screw feed), 11, Waugh 93, 95; Waugh 16; Sullivan DR-6, DW-64, T-3; DP-321, DP-331; DA-21, DT-44, DT-421; Gilman AX-321 (motor rotation and air feed); Cleveland D-5; AIBQ, 44-SWR,

Jan 1, 1940

By T. Suzuki

LABOR. conditions have finally caused rock-drilling machines to supplant hand drillers in the Japanese mining industry, and have encouraged this study. During a period of three years 25,000 tests were made on 67 different American, Japanese, and European rock drills, using, respectively, the Paynter testing machine, and drilling in granite and limestone. Recorded were: air consumption, speed of rotation, torque of rotation, foot-pounds of striking energy, air pressures, input horsepowers, and speed of rock penetration. The author expresses his views on the interrelation of these factors and offers theoretical support, as well, by formulas based upon the mechanics of impact. He discusses the different designs of the valves, cylinders, piston hammers and rotation devices involved in the different types of rock drills, with respect to their merits and defects and offers conclusions about the factors that should be considered in the new design of a superior rock drill. The author&apos;s mathematical demonstrations and arguments for a value of "best feed clearance" of the drill bit from the rock are based upon the hand-operated screw-fed type of hammer drill. Automatic feeds have not been considered in this paper except for the tests on one drifter with air feed, 10 air-feed stopers, and some hand-held blockholers. The following classes of drills, with one of each model, size, or type, were tested: 23 heavy drifters, 34 light drifters and hand-held drills, and 10 stopers. They represented the following makes and models: 40 from the United States—namely, Ingersoll-Rand 18, 148, L-74, 24-70, N-72, N-75, R-72, 26, BAR-33, BCR-430, DCRW-23, RA-12, CA-31, CC-11; Denver 7, 107, WT-21, WT-31, WT-331, WT-337 (models WT with motor rotation, screw feed), 11, Waugh 93, 95; Waugh 16; Sullivan DR-6, DW-64, T-3; DP-321, DP-331; DA-21, DT-44, DT-421; Gilman AX-321 (motor rotation and air feed); Cleveland D-5; AIBQ, 44-SWR,

Jan 1, 1940

By A. Faber du Faur

At the request of some of the members to whom I have shown a collection of specimens of sulphur from southern Utah, I herewith present some notes relating to the mines and the method of extracting the sulphur from the ore. In preparing these notes I have borrowed from a paper by Prof. G. vom Rath, published in the Neue Jahrbuch fur Mineralogie, vol. i., 1884, dated Salt Lake City, December, 1883. The Cove Creek sulphur-bed, now worked by the Dickert & Myers Sulphur Co., is in Beaver county, near the line of Millard county. It was first discovered by Mr. Ferdinand Dickert in 1869 ; other beds in the same neighborhood mere found by him from 1872 to 1875, making altogether 22 mining claims. The want of railroad communication prevented the early development of these claims; but in 1883 Mr. F. Dickert put up a plant for extracting sulphur from the ore, which proved a perfect success; and in 1885 the property was transferred to a stock company organized under the laws of Utah. The railroad station nearest to the Cove Creek mines is Black Rock, on the Utah Central Railroad, 204 miles south from Salt Lake City, and about 26 miles west of the mines. The road from Black Rock to the mines passes through desert and lava-bed, to the road leading from Kanosh to Beaver, which latter road it joins near Cove Creek fort, a square stone enclosure, erected by the Mormons for protection against the Indians. Cove Creek fort is situated near the eastern limit of a plain bounded on the west at a distance of about 12 miles by the Mineral range, and on the east by the Sulphur mountains, forming part of the Tushar mountains. To the northwest the plain runs into the Sandy desert. About 3 miles from the fort rises a solitary hill about 1000 feet above the

Jan 1, 1888

By F. W. Glaser, Benjamin Post

A LTHOUGH most transition metals form a wide variety of boride compounds, the existence of only one zirconium boride, ZrB2, had been established prior to this investigation.&apos; The crystal structure and some properties of a hitherto unreported zirconium boride, ZrB12, are described in this paper. Only one other dodecaboride of a transition metal, UB12, has been reported up to the present.&apos; Chemical analysis of the new compound showed 44 pct Zr and 56 pct B, compared with 41 pct Zr and 59 pct B computed for ZrB12. The difference is within the range of error of the analytical method employed. ZrB12 shows marked metallic properties. It is obtained as a fine black powder. Measurements of electrical resistivity were made at —79°C, + 22°C and +64°C. At 22°C the electrical resistivity is approximately 60 microhm-cm. Over this range the temperature coefficient of resistivity is +0.00162. The thermal conductivity at room temperature is 0.122 watts per cm per "C. The product of the electrical resistivity and thermal conductivity is therefore 8.05, which is not far from the normal Wiedemann-Franz ratio (approximately 7.5 at room temperature). These measurements were made on hot pressed samples which were not always high density specimens. The hardness of ZrB12 on the Rockwell A scale varies between 92 and 92.5. Crystal Structure Determination Single crystals of ZrB12 of a size suitable for X-ray diffraction analysis could not be obtained and powder samples had to be used. Filtered Cu radiation was used throughout. Powder diagrams were indexed on the basis of a face-centered cubic unit cell. After correction for film shrinkage, a Bradley and Jay extrapolation³ to ? = 90" indicated that a, = 7.408 ±0.002A. The volume of the unit cell is 406.5A.V he assumption that there are four "molecules" of ZrB12 per unit cell leads to an X-ray density of 3.63 g per cc. The measured density is 3.7 g per cc (as measured by the immersion method). Relative intensities of reflections were determined by integrating the intensities of diffraction peaks using the count register of a North American Philips wide range spectrometer. Intensities measured in this way showed good agreement with photographic intensities estimated visually using multiple film techniques. The usual Lorentz, polarization, and multiplicity corrections were applied to the observed intensity measurements. There are striking similarities between ZrB12, and UB12. The unit cell of the latter is also face-centered cubic and contains four molecules. a, = 7.473, compared with 7.408 for ZrB12. The radius ratio rB/rU is 0.57; rB/rZr is 0.54. In both ZrB12, and UB12 the four metal atoms in each unit cell are in special positions; only the boron positions need be determined. The latter may be inferred from the extent to which diffraction of X-rays by the 48 boron atoms reinforces or weakens the diffraction by the metal atoms. This effect is relatively much greater in the case of the zirconium compound. In their determination of the crystal structure of UB12, Berthaut and Blum&apos; assumed holohedral symmetry (space group Oh5 , Fm3m) and reported that the U atoms are in positions 4(a): 000; 01/2 1/2; ½ 0 ½ ; ½ ½; the boron atoms were reported to be in positions 48(i) with x = 1/6: ½xx; ½xx; x½x; x½x; xx½; xx½; ½xx; ½xx; x½x; x½x; xx½; xx½

Jan 1, 1953

By T. Wasson

The same limitations&apos; that characterized 1931 existed in the old fields of Indiana and Illinois during 1932. Prices remained low. The average for the year for Illinois and southwestern Indiana was $1.032 as against $0.852 for 1931 and $1.616 for 1930. In September a curtailment of production of about 25 per cent became effective and was continued to the end of the year. There were no new discoveries and very little wildcatting was done. Considering the age of the wells, and the number still producing, there were few abandonments. The most outstanding thing about the old fields in these states is their long continued productivity. Illinois The fields along the southeast end of the LaSalle anticline had their peak of 33,686,000 bbl. in 1908. In 1932, with a 25 per cent restriction for 355 months, these fields produced 4,661,000 bb1.l There were 52 new completions (most of them in old territory) and of these 33 were dry, 8 were gas, and 11 were oil wells. The new oil wells had a total initial of 102 bbl., or an average of 9.3 bbl. per well. Nineteen of the new producers were in Crawford County. There were about 200 wells abandoned in the old southeast fields in 1932 as compared to 210 in 1931. The greatest number, 86, were in Lawrence County. To the end of 1932, the four major counties—Clark, Crawford, Lawrence and Wabash—had produced almost 394,000,000 bbl. from 92,160 acres. Better than one-half of this was produced in Lawrence County from 26,240 acres. The Dupo area of Sinclair County had no additions to production although four wells were drilled. On the Jacksonville structure in Morgan County, six gas wells with an average depth of 300 ft. were drilled to sands in the base of the Pennsylvanian. They produced an open-flow total initial of 2,000,000 cu. ft. This gas will be developed further to supply a local market.

Jan 1, 1933

By Eckley B. Coxe

I wish to call the attention of the Institute to a peculiar variety of anthracite which occurs in the Buck Mountain vein at our collieries at Drifton, and in the same and other veins in different localities in the anthracite coal-fields. It is known among the workmen as iron-gray or cast-iron. It has a dull, greasy appearance, as if a piece of ordinary anthracite had been rubbed with a dirty and greasy rag and allowed to dry. It was formerly considered a very impure coal containing a high percentage of ash, and was picked out of the coal and thrown away. But the following analysis of it and of its ash, made by Mr. J. Blodget Britton, of Philadelphia, shows that such is not the case, the percentage of ash not being much higher than that of the ordinary anthracites as they are prepared for market. ANALYSIS OF COAL. Water,.........4.36 Fixed carbon, by difference,.. 84.90 Volatile combustible matter,. . 3 48 Ash,..........7.26 100.00 The carbon proved to some extent to be of the nature of graphite, and slowly combustible. ANALYSIS OF ASH. Silica,.........25.66 Sulphur,........ .17 Alumina,........27.03 Phosphoric acid,.......21 Ferric oxide,.......42.83 Alkali, undetermined matter and Lime,.........1.56 loss,.........60 Magnesia,........1.83 Manganous oxide,......11 100.00 We recently collected a quantity of the substance and made a fire with it, in an ordinary stove, which was kept up several days. We found that it burned with intense heat, and apparently as freely as our other coal does. Mr. Britton is probably right in his view, that the difference in appearance is not due to impurities in the coal, but to the fact that the carbon is in a more or less graphitic form, as many of the standard coals are no purer. I bring this before the Institute as I know that a large quantity of this valuable fuel is thrown away every year, on account of its supposed impurities.

Jan 1, 1879

By K. Reinhardt

The idea of burning blast-furnace gases directly in gas-engines, instead of under steam-boilers, as had previously been done, was first put into practice barely ten years ago, almost simultaneously in Great Britain, Germany and Belgium. The pioneers of this movement made their first experiments with small engines. After these experiments had given satisfactory results, and it had been shown that the thermal value of the poor blast-furnace gases, in spite of defective scrubbing, could with safety be directly transformed into mechanical work in the gas-engine, there very soon arose a considerable demand for gas-engines of large power, similar to the large steam-engines employed in metallurgical works. In face of these sudden requirements, the gas-engine builders were placed in a difficult position; for up to that time the gas-motor was considered as suitable for small engines only, and it was generally believed that the limit of size had been attained with 100 to 150 effective h.p. in a single cylinder. Manufacturers of gas-motors, however, did not underrate the advantages offered by this new field for their manufactures, and it so happened that in Germany the Berlin-Anhaltische Masch-inenbau-Gesellschaft, of Dessau, was the first to undertake the construction of a 600-h.p. two-cycle gas-engine, with two cylinders of the Oechelhauser-Junkers type, for the Hoerder Mining & Smelting Company. The engine was started in 1898, and, with a few improvements and alterations, is still working satisfactorily. This engine worked with astonishingly high effciency, considering the period. The builders were therefore

Jan 1, 1907

By W. O. Philbrook, K. Natesan

The oxidation kinetics of spherical pellets of zinc sulfide made from Santander concentrates were studied using a thermogravimetric technique. The experiments covered a temperature range-. of 740" to 102O°C, 0-N mixtures varying from 20 to LOO pct O2, and pellet diameters between 0.4 and 1.6 cm. Mathematical models were formulated to Predict the reaction rate on the assumption that a single transport or interface reaction step was rate -controlling. Analysis of the data indicated that the process of oxidation was predominantly controlled by transport through the zinc oxide reaction-Product layer. ROASTING processes, which are reactions between solids and gases, are very important because they are employed in the production of a number of basic metals. These processes are highly complicated, and one needs to consider the transport phenomena of heat and mass between the solids and gases in addition to the kinetics of various chemical reactions involved. Because of such complications there is a lack of knowledge concerning the rate-limiting factors, which may strongly depend on temperature, particle size, gas composition, and solid structure. The oxidation of zinc sulfide, which is of commercial importance in zinc production, falls into this class of reactions. The major goal of this work was to elucidate the roles played by different process variables, such as reaction temperature, gas composition, pellet size, and pellet porosity, on the kinetics of oxidation of single pellets of zinc sulfide. Roasting of zinc sulfide single particles has been a subject of both experimental and theoretical investigations.&apos;-&apos; The reaction is exothermic and may be considered to be irreversible. Such a reaction has been found to proceed in a topochemical manner. In other words, as the reaction proceeds, a progressively thicker outer shell of zinc oxide is formed, while the inner core of unreacted sulfide decreases. It has been found experimentally, both in the present work and in the previous investigations,1-9 that the particle retains its original dimensions and the process requires transport of gaseous oxygen across the porous product layer for continued reaction. The reaction may be represented by ZnS(s) + 3/2 O2(g) = ZnO(s) + SO2(g) [1] The solid product considered here is only zinc oxide, since the diffraction patterns of zinc sulfide pellets oxidized partially at &apos;798" and 960°C showed K. NATESAN, Junior Member AIME, formerly St. Joseph Lead Fellow, Department of Metallurgy and Materials Science, Carnegie-Mellon University, Pittsburgh, Pa., is now at Argonne National Laboratory, Argonne, Ill. W. 0. PHILBROOK, Member AIME, is Professor of Metallurgy and Materials Science, Carnegie-Mellon University. This paper is based on a them submitted by K. NATESAN in partial fulfillment of the requirements for the Ph.D. degree in Metallurgy and Materials Science at Carnegie-Mellon University. Manuscript submitted December 2, 1968. EMD lines corresponding to original zinc sulfide and the newly formed zinc oxide. OXIDATION MODEL The generalized model for gaseous oxidation of zinc sulfide is illustrated in Fig. 1. This depicts a partially oxidized sphere of zinc sulfide in a gas stream surrounded by a laminar film of gas. The spherical sample of zinc sulfide of unchanging external radius r0 is suspended in a flowing gas stream of total pressure PT and composition specified by the partial pressures of the individual components. Partial pressures of the gaseous species in the bulk gas phase, at the exterior surface of the pellet, at the ZnS/ZnO interface, and at equilibrium for Reaction [I] are identified by the superscripts b, o, i, and eq, respectively. The overall reaction involves the following ~te~s:&apos;~&apos;~&apos; Step 1. Transfer of reactant gas (oxygen) from the bulk gas stream across the gas boundary layer to the exterior surface of the pellet and the reverse transfer of the product gas (sulfur dioxide). Step 2. Diffusion and bulk flow of oxygen from the pellet surface through the product shell (ZnO) onto the ZnS/ZnO interface and the reverse transfer of sulfur dioxide. Step 3. Chemical reaction at the interface, which results in consumption of oxygen gas and generation of sulfur dioxide gas and heat; at the same time the _________ PARTICLE SURFACE / x^^^^n^X / MOVING INTERFACE core-----/ sJSNxy " /T^T^02 \ V\V$\ ^NWX/ "*/— GAS BOUNDARY x. \\ZnO SHELLV/ / \^ . / &apos; ^ BULK GAS --------N_______ _____,------p£ w \ P« / (f> \ / a \ <i) / <----------------- _(o) ^^--------------(b) °- pso, pso2 ro ri 0 ri ro RADIAL POSITION Fig. 1—Generalized model for oxidation of a sphere of zinc sulfide.

Jan 1, 1970

By G. A. Swanquist, E. M. Morales

INTRODUCTION The idea of water management and control at the Church Rock Mill operations began to take shape in February 1979. At that time, we were already investigating the feasibility of decreasing the fresh water requirements so that the solids would become the limiting factor in tailings impoundment utilization. The area for solution evaporation could be kept at a fraction of the normal requirements under the standard process of full water usage. The Church Rock Mill is an acid leach circuit followed by solids/liquid separation with thickeners in counter current decantation, and solvent extraction. Following the normal design of acid leach circuits, reuse of tailings solution was not incorporated in the original mill process design. INITIAL WATER CONTROL INVESTIGATIONS The investigations to decrease the fresh water requirements centered around modifying the grinding circuit from the present semi-autogenous grinding (SAG) mill in closed circuit with hydrocyclones, to open circuit grinding with a rod mill. The open circuit grinding with the SAG mill and rod mill in series had the potential of decreasing the water requirements for grinding and leach dilution by approximately 50% or 1.4 m3/min (300 gpm). The grinding pulp density would be maintained at 70 to 72% solids, and the leach dilution to 50% solids would be accomplished with acid tailings liquor recycle. In such a grinding circuit arrangement, the SAG mill would provide the primary or coarse grind, and the rod mill would be used for the fine grind. By the SAG mill and rod mill series grinding method of water control and other secondary water controls in various places downstream from the grinding circuit, the required necessary evaporation area was estimated at 120 acres of liquid surface. A second method of water control at grinding was investigated. A two-stage cyclone classification circuit appeared to have a good potential of achieving the same water reduction at a much lower capital and operating cost. However, in retrospect, this would not have been a viable method since a high slime recycle load would have been established hindering classification. The use of reagents to neutralize the acid tailings solution was not considered seriously at that time, since it would have materially increased operating costs, although it would have also allowed more tailings solution recycle and consequently, less fresh water usage. However, with the tailings solution deposition area available at that time, it was not then necessary to incur the high cost of neutralization. The control expected by the series grinding of semiautogenous and rod mills would have been sufficient to maintain a water consumption/evaporation equilibrium well in line with the available land area. IMPLEMENTATION OF NEUTRALIZATION OPERATIONS During the summer of 1979, the UNC Church Rock Mill experienced a tailings dam breach which resulted in a prolonged mill shutdown. Upon resumption of operations at the end of October 1979, tailings deposition was restricted to a small portion of the tailings impoundment area. Figure 1 shows the general tailings area and the limits of the present deposition area in the central part including the borrow pits. These borrow pits had been excavated to provide materials for tailings dam construction. Immediately after resumption of operations, it became evident that it would be necessary to control the quantity of liquid to be evaporated because of the small confined area available for tailings solution deposition and to maximize the deposition time in the tailings area. The water control required had to be exercised on a large scale, and to be in operation as quickly as possible. An obvious solution was to reuse the tailings liquor in mill process. Immediate steps were taken to install the necessary equipment for tailings neutralization on an interim basis. Anhydrous ammonia was selected as the primary neutralization reagent since it was the quickest system that could be placed in operation. Previous laboratory tests indicated fair results with ammonia neutralization. Such a system required a minimum of installed equipment and handling. INITIAL NEUTRALIZATION OPERATIONS Actual neutralization operations began on November 26, 1979. The raffinate solution which normally would have been discarded was pumped to a 3.7 m (12ft) diam by 4.3 m (14ft) tank for reagent contact, see Figure 2. At this tank, anhydrous ammonia was added directly from the tanker trailers and controlled at pH 7.0 nominally. Agitation was provided by air sparging. The neutralized product formed a highly viscous slurry in the grinding circuit which resulted in pumping and cyclone classification problems.

Jan 1, 1982

By Eric Jette

IN a recent article,1 the authors reported the results of an X-ray investigation on the range of solid solutions that occurs in the iron-oxygen system in the vicinity of the compound FeO, which frequently is called "Wüstite." The object of that investigation was primarily to study the unusual type of solid solution phenomena involved in this range. Briefly summarized the results were: 1. The NaCl type of lattice found by earlier workers was confirmed. 2. The lattice dimensions decrease rapidly with decrease in iron content. 3. No alloy that was a homogeneous single phase was ever found at compositions beyond 76.80 per cent Fe, while the theoretical iron content of FeO is 77.73 per cent Fe. 4. Measurements of the densities and lattice constants led to the conclusion that the form of substitution was complex, an FeO group being replaced by oxygen. Such a substitution, of course, is equivalent to removing an iron atom (or ion). The ideal unit cell of FeO can be con-sidered as containing four groups of FeO and, thus, when this type of substitution takes place, there remain in the unit cell three FeO groups and an oxygen, or a total of seven atoms with a gross formula of Fe304 instead of the original Fe404. 5. This was the only interpretation that would fit the experimental results and at the same time be consistent with (a) the previously deter-mined fact that the FeO lattice is ionic (i. e., consists of Fe++ and 0= ions) and (b) the chemical fact that as the oxygen content of the substance increases, ferrous iron becomes oxidized to ferric iron. The experimental results of this investigation are included in Fig. 1.

Jan 1, 1933

By Arthur S. Wright

THE accuracy of the silver-assay depends in great measure upon a careful regulation of the heat of the muffle during the process of cupellation. At the beginning of the operation, a relatively high temperature is required to " open " the lead buttons, that is, to clear off the black film of oxide that covers the surface of the metal button immediately after fusion has taken place. The muffle is usually closed up until the buttons are uncovered. As soon as a clear, free surface of molten metal is exposed to the oxidizing action of the air, the temperature should immediately be lowered to the minimum temperature at which the formation and absorption of litharge can progress freely, and the buttons still be kept from " freezing." The process, under satisfactory conditions, will be characterized by the formation of rings of litharge crystals (" feathers," as they are styled), on the cupel, about the oxidizing globule; and the nearer these rings of litharge crystals call be made to approach the central oxidizing globule without interfering with the freedom of oxidation and absorption, the smaller will be the volatilization of silver, and consequeiltly the greater the degree of accuracy attained. This minimum heat must be maintained uniformly during the oxidation of the lead; and just as the last of the lead is disappearing, and the button is preparing to l blick," the temperature of the muffle should be allowed to rise so that the last traces of lead will be driven off. This regulation of the heat calls into play all the skill of the assayer, and requires a vigilant eye, able to distirlguish between the slightest variations of temperature of the muffle, assisted by a nice adjustment of fuel and draft. With a few cupels in the muffle at one time, the proper heat for each cupel can be maintained by roughly approximating the proper temperature, and then moving the cupels backward and forward in the muffle; but this is gene-

Jan 1, 1897

By Edward J. Felten

THE oxidation resistance of chromium and Fe-Cr alloys is increased by small additions of yttrium or other rare earth metals.1,2 In addition, the presence of the additives increases the resistance of these alloys to spalling of the external oxide above 1000°C. This ability to prevent spalling appears to be related to the formation of an internal oxide in alloys containing yttrium or the other rare earth metals. The internal oxide is found in the form of a filamentary growth concentrated in the grain boundaries of the unoxidized metal. In alloys containing yttrium this internal oxide was found to be either Y2O3 Or YCrO3.&apos; In an earlier report,&apos; the growth of the external oxide was found to be controlled by diffusion through the oxide layer. Thermal balance studies were used to establish the kinetics of external oxide formation. In this related study the rate of growth of the internal filamentary oxide has also been studied. The results obtained indicate that the growth of the internal oxide is also diffusion controlled. Internal oxidation appears to occur in at least two ways. Using copper alloys containing small amounts of silicon, Rhines 3 found that between 600" and 1000oC a subscale was formed which consisted of particles of silica dispersed in the metallic matrix. The conditions requisite to internal oxidation as suggested by Rhines are: 1) a solubility of oxygen in the alloy, 2) the ability of oxygen to diffuse at an appreciable rate into the alloy, 3) the possibility of the formation by the alloying element of an oxide more stable than the oxide of the host metal, and 4) a relatively low solubility of this oxide in the metal. These conditions are fulfilled for a number of other copper alloys.3-5 Furthermore, the relationship between the depth to which the internal oxide is formed and the oxidation time follows the simple parabolic law.6 The activation energy for copper containing small amounts of silicon, germanium, iron, or manganese as calculated from Rhines data6 is about 48 kcal per mole. In some cases the internal oxide is found segregated at the grain boundaries, especially near the the surface. Observations of this type of oxide formation have been reported by stead,7 Rhines,* and Lustman. Evans" cites these cases as examples of the simultaneous movement of anions and cations during oxidation. Furthermore, Evans states that the presence of a minor constituent with a high

Jan 1, 1962