Search Documents

By A. M. Kivari

OPERATIONS at the cement plant of the Permanente Corporation, in the hills about 45 miles south of San Francisco and 12 miles west of San Jose, are interesting to the members because of the adoption of modern hydrometallurgical methods for handling and beneficiating raw materials Closed-circuit grinding, classification, hydroseparation, flotation, agitation, and thickening are familiar terms at this cement plant These methods make it possible to process refractory limestone into suitable materials for the manufacture of modern cements Construction of the plant, haying originally a design capacity of 7000 bbl of cement per clay, was started in June 1939, and the first clinker was ground on the following Christmas Day At present the capacity is about 12,000 bbl of finished cement per 24 hr , most of the production being low-heat cement † About 3130 tons of limestone, 620 tons of clay and 100 tons of gypsum are required daily for this output Occasionally iron oxide is added to the clay to obtain the desired composition This, together with the gypsum, is purchased from outside sources Up to the present time, the corporation has produced low-heat, normal, moderate¬ heat, moderate-sulphate-resisting, high-early-strength, oil-well, modified-oil-well, and plastic cements Most of the present production is for Shasta Dam, near Redding, Calif , the told demand being 5,800,000 bbl of cement Following are sonic of the cement requirements of the Shasta D [im] specifications [ ] The average specific surface in the bin s sampled shill be not less Ulan 1800 sq cm per gram and no individual sample less thin 1600 sq centimeters Compressive strength The average compressive strength in pounds per square inch of three mortar cubes composed of one part cement and 2 75 parts fine testing sand, by weight, shall be equal to or greater thin the following

Jan 1, 1941

By John L. Burns

The object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-hardening characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classification" is essayed. A.—Relation of Lattice Parameter and Electrical Conductivity to Changes in Physical Properties Due to Aging of Fe-C Alloys Since Whiteleyl in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A, point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,~ and at the same time and independently, W. Koster,~ proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By William M. Baldwin, T. S. Howald, A. W. Ross

EXPLORATORY WORK THE related subjects of preferred orientation, directionality in physical properties, and earing tendencies of wrought metal [ ] strip have attracted the attention of metallurgists to such an extent that in the past 20 years hundreds of researches have been published on this one general problem. The anisotropy of tensile strength and elongation have been exhaustively studied in their relationship to the occurrence of ears in cups drawn from strips-20.29 and, to a lesser extent, yield strength7,11,17 and stress-strain curves" have been investigated. Despite the tremendous fund of knowledge thus accrued, no simple quantitative correlation of directionality and earing tendencies has yet been found. In a sense, this is not surprising. The formation of ears in a drawn cup clearly is a special phase of the general study of metal flow; in particular (as will be brought out in the course of this paper), ears are due to anistropy in the rates of deformation of the metal in the radial, circumferential, and "thickness" directions of the original blank. It would be difficult to effect a correlation between earing tendency and a property that may be completely independent of the flow of metal, or at best related to metal flow in an exceedingly complex fashion. Yet, it is this correlation that has been attempted; tensile strength and elongation are attributes of metal rupture, a phenomenon that has quite admirably been shown to be distinct from the phenomenon of metal flow,21 while yield strength and stress-strain

Jan 1, 1945

By Ulick Evans

I SHOULD like to commence by saying how much I appreciate the honor which the American Institute of Mining and Metallurgical Engineers has done me in inviting me to visit your country, and to deliver this lecture before you. In choosing a subject, and in deciding what to include and what to omit, I have endeavored to discuss as far as possible work carried out recently in Europe with which you may not be unduly familiar. It would be poor return for your hospitality, and a mistaken sort of compliment indeed, if I were to load the lecture with accounts of researches carried out in your own country-researches with which you are probably better acquainted than I. Not that I have in any way excluded work done on this side of the Atlantic from my survey; one would indeed find it difficult to write on this, or on any other branch of science, without mentioning American work. But I have endeavored as far as possible to concentrate on aspects of the case which will, I hope, be comparatively fresh to you, and I feel fairly certain that this will be in accordance with your own wishes. If a strip of iron is heated strongly at one end, the other end remaining cold, there is produced over the heated portion a layer of oxide scale, the thickness of which diminishes steadily with the distance from the hot end. Somewhere in the middle of the strip, the thickness of the oxidized layer will become comparable to the wave length of light, and over this region the thin films give rise to a series of beautiful interference tints, commonly known as "temper colors." The colors are caused by the fact that two trains of light waves are reflected respectively from the outer and inner surfaces of the oxide film, and the possibility arises that the "crests" of one series of waves may coincide with the "troughs" of the other, thus diminishing the intensity of the light of some particular wave length. The state of affairs in this part of the strip is shown diagrammatically in Fig. 1, in which the film thickness is enormously exaggerated, of course, in comparison with the length of the strip; the

Jan 1, 1929

By Milton Williams

A comparison is made between the amount of interstitial water found by analysis in cores and that estimated from the resistivity curve of the electric log for the corresponding strata of producing reservoirs. It is shown that while the determined and the estimated water saturations are in good agreement in some cases, this agreement may be due to a fortuitous compensation of errors. Estimates of water saturations made from the electric 1og by use of existing relations should, therefore, be employed with caution. Also presented are data on the variation of salinity of interstitial waters in reservoir sands, and on the effect of variation of salinity and porosity on the validity of estimates of water content made from the electric log. INTRODUCTION Throughout the history of electric logging there have been recurrent cycles of optimism and pessimism as to the value of the electric log in the quantitative estimation of reservoir fluid content. The very early days of electric logging were an optimistic period, in which there was widespread faith in the ability of the resistivity curve to reflect fluid content, and in the ability of the potential curve to indicate textural characteristics. In time the accumulation of exceptions to this idealistic behavior brought about a general disillusionment, and caused the more pessimistic of those dealing with electric logs to believe that the sole importance of the log lay in stratigraphic correlation. Within the last several years optimism as to the quantitative use of the electric log has been revived, primarily as the result of the stimulating work of C. E. Archie' on the estimation of interstitial water in sands from resistivity data. Even though the general trend of thought on the quantitative value of the electric log reflects optimism, it is inevitable that there are some widely divergent opinions of the validity of quantitative estimates based on the electric log. A valid method of estimation of fluid content by means of the electric log and a general knowledge of the textural character of the reservoir rock would be of signal importance, not only in that it would save time and money in securing information on reservoirs now being drilled, but also because it would permit the evaluation of reserves in many fields drilled without adequate core data subsequent to the advent of electric logging. Because of this importance, Humble's Production Research Division, in cooperation with various other company divisions, initiated several years ago series of tests designed to evaluate the reliability of estimates of fluid content made from the electric log. The investigation was limited at the outset to sand reservoirs, since it was felt that the inclusion of limestone reservoirs would entail needless complications. In devising these tests it was immediately apparent that the chief difficulty in evaluating the worth of any method of estimation lay in establishing the true value of fluid content. The results of direct analyses of cores cut with ordinary mud were not sufficient, because of the probability of contamination of the fluids by filtrate from the drilling mud; the results of restored state tests on cores were deemed unsuitable because these results can hardly be said to furnish a primary standard. The method adopted was the direct analysis of cores cut with an oil-base drilling fluid. Such cores, when properly handled, are believed to afford the most precise determination of water content available at the present, and, in addition, lend themselves readily to the determination of various other properties which are pertinent to the estimation of fluid content from the electric log. Since it was desired to compare the fluid contents estimated from the electric log run in ordinary mud with cores cut in the same hole, the use of oil-base fluid necessitated the changing over, after all cores were cut, to a conventional mud. This procedure presented several advantages, one of which was that the use of oil-base fluid permitted

Jan 1, 1950

By Michael P. Robinson

It has been suggested that streaming potentials are not nomlally logged because the streaming potentials known to be generated across mud filter cakes are substantially cancelled by streaming potentials generated in contiguous shale beds. Laboratory measuments of streaming poterztials acrons hand specirnens of shale have been adduced as evidence to support the suggestion. The experiments show that streanzing potential depends on the resistivity of the equilibrating solution and on pressure drop. Meizsurenlents were made perpendicular to the bedding planes of the shales. The mechanism of streaming potential generation in shale which the suggested cancellation theory iniplies has been critically examined. Conclusions reached are tested by comparing self potentials logged before and immediately after changing the resistil~ity (but not the weight) of mud in a borehole. The resultant SP change is found to equal the theoretical electrochetnical potential change, i.e., cancellation of .strearning potential is independent of mud resistivity. Since streaming po/entials generateal across mud filter cakes depend critically upon mud reistivity, shale .strearlling potential in situ must he equally sensitive. Using plausible values for the pemleahility, porosiy arzd compressibility of shale, the van Ererdingerl-Hurst approach shows that the pressure drop between horehole pressure and formation pressure in a radially honzogeneous shale is unlikely to coincide with the zone of filtrate invasion. If, perchance. this coincidence occurs with one mud a chatzge 10 a second must result in non-coincidence, i.e., a .YP logged in the second mud should show a streaming potenlial. The dilernrna may he overcome by postrrlating: (I) perrneabilities of shale7 parallel to their beddine planes greatly exceed their cross-bedding permeabilities; (2) a resistivity-sensitive mud cake of low permeability forms either on the face of, or probnhly in the lanlinations of, many shales. These postulates are examined with reference to the pres.sure and SP histories of the McClosky and Aux Vases zones in the Illinois Basin and some srcpport for them found. It is concluded that a definitive solultion to the streaming potential problem does not exist. INTRODUCTION Recently Gondouin and Scala' published a contribution to the streaming potential problem which is notable particularly for the elegance of its experimental techniques. The conclusions drawn by Gondouin and Scala from their studies amplified those previously suggested by Schehck'. In essence they suggested that the streaming potentials known to develop across mud filter cakes" are not normally observed on SP logs because they are largely cancelled by streaming potentials generated in adjacent shales. This suggestion appears so reasonable that many workers in the logging field will be prone to accept it. We incline strongly to the view that the suggestion is basically correct. Nevertheless, it is important to realize that the cancellation hypothesis in the form put forward by Gondouin and Scala does not appear to meet all the known experimental facts. It is the principal intention of this note to call attention to what appears to be a flaw in the relevancy of the experimental evidence adduced by Gondouin and Scala and to suggest an alternative hypothesis to remove it. The consequences of the new hypothesis are compared with field data which, we believe, are unique. A second but not less important purpose of this note is to emphasize that even the new hypothesis does not fully explain all field observations. Hence we conclude that further study of the streaming potential problem is required before it can be said that a definitive solution to it has been attained. The bare experimental bones of laboratory data on streaming potentials appear to be as follows. 1. A streaming potential is developed across a mud filter cake. This streaming potential is virtually independent of cake thickness but depends on the mud resistivity. The relationship is of the form, 2. A streaming potential is developed across a shale. This potential is independent of shale thickness but depends on the resistivity of the permeating solution if the shale has been first equilibrated in this solution. The relationship is of the form, The relationship in (1) was determined first by Wyllie3, confirmed by Gondouin and Scala and qualita-

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

By H. J. Hand

Statistical methods are becoming increasingly important for interpreting routine reports, or for analyzing special test data in industrial plants, such as steel plants. They have already become practically a necessity to the plant metallurgist. A paper by Chancellor, 1 written in 1933, gives many examples of the benefits the plant metallurgist can derive from the use of these methods. The present paper discusses applications of importance to many others who must analyze reports in the steel plant, as well as other examples of interest to metallurgists. Statistical Methods Logically Suited to Plant Problems.—Statistical methods are not new as a branch of mathematics. Until comparatively recently, however, practical applications were confined mainly to actuarial science, biology, and economics; fields in which an observed result is obviously influenced (and often determined) by a complicated set of variables more or less constantly tending to affect it. As pointed out by Daeves,2 a decade or more ago, problems in industry are basically similar to those in these other fields in that a given result is at least partly due to that chance combination of causes happening to be present at the time. When trying to do the same thing repeatedly, constant results are never attained; they vary about the desired result with more or less well defined mathematical regularity. Such a condition arises out of the great number of factors tending to affect the final result. If statistical methods are so valuable to the biologist or economist, why then should they not also be of great value to plant managers and engineers, and to all who must interpret reports from various sources in the industrial plant? Within the last few years, industry has become conscious of this situation, and the use of these methods has been rapidly expanding in such p1ants. Many Useful Statistical Devices Available.—Many statistical methods of attack are available for the analysis of plant data. It is the object of

Jan 1, 1938

E. B. WILSON, Scranton, Pa. (written 'discussion *).-Prof. Young's paper shows another application of electricity in solving problems in coal mining, and suggests that it may be possible to utilize the data he has collected in developing an electric firedamp detector. If electric lamps are to be adopted in gassy coal mines, the use of an electric firedamp detector becomes almost imperative, for safety lamps and electric lamps in the same mine are not always conducive to safety, and Liveings electric firedamp detector, is too cumbersome to meet with general approval. Three well understood facts are verified in a new way by Prof. Young's experiments: - 1. The temperature at which methane ignites. 2. The more inflammable gas present in an atmosphere, the hotter will be the flame, and the longer the cap in a safety lamp. 3. As the temperature at the source of ignition varies, the length of the gas-cap flame varies. Prof. H. B. Dixon collaborating with Mr. H. F. Coward, some years ago, made experiments on the ignition of various gases to find the tem-perature of their kindling points.1 From the results of their experiments, the writer has culled the ignition temperatures of some hydrocarbon gases, and has tabulated them with other data, in Table 1.

Jan 10, 1919

By L. C. Graton

INTRODUCTION CLEAR recognition by Lindgren1 of the important control exerted by physical conditions on the formation of ores laid the foundation for that long-sought attainment, a classification? of mineral deposits based consistently on origin. In probably no other portion of the realm of mineral deposition has the importance of physical influences been so manifest or the validity of Lindgren's genetic classification been so well proved as in that extremely important family of ore deposits which are now universally classed as hydrothermal and generally regarded as of magmatic derivation. While many varieties of deposits, some of them possessing great scientific interest and economic importance, fall outside the limits of this hydrothermal group, inclusion within it of most of the veins and a vast number of the replacement deposits of the world gives to this grand genetic class at once a dominating importance and a powerful scientific appeal. Nowhere are these vein and replacement deposits of hydro- thermal lineage more generously distributed, more extensively exploited or more thoroughly known than in the Cordilleran province of the United States. One of the respects in which these hydrothermal deposits command the interest of both geologists and mine operators is in their relation to depth: the great vertical range through which many of them have already been developed, the disappointing failure of others at relatively shallow levels, and the noteworthy downward changes in character and tenor exhibited by still others. In this hydrothermal category (if the Rand be granted place here) are included the ores of all the very deep mines of the world, ranging from 5,000 to nearly 8,000 ft., as well as of many other mines undoubtedly destined in time to attain corresponding depths.

Jan 1, 1933

By Harrison, Henry Fay

The study of an entirely new series of alloys may be undertaken from a desire to obtain knowledge applicable to the perfection of industrial alloys, or merely to test certain theoretical considerations. In the case of antimony-tellurium alloys, the theoretical side only is at present important; but it is hoped that the results of this investigation may have some industrial value, at least indirectly, by furnishing one more example for comparison when studying commercial alloys. The statement is found in various places that antimony is isomorphous with arsenic, bismuth and tellurium; but very little experimental evidence has been offered in support of this assumption. All four metals crystallize in rhombohedra, and the ratio of the axes a: c is approximately the same—which seems to indicate, but does not prove, their isomorphism. The close association of these metals in minerals also seems to indicate that they are isomorphous. There are, however, certain differences in their properties which render this coriclusion somewhat doubtful, and it is therefore desirable that inde-

Jan 1, 1902

By Parke A. Dickey

POTENTIAL differences between strata of shale and sandstone have been recognized for about 15 years, and they form the basis of the electrical logging of oil wells. Hitherto these potentials have been ascribed solely to electrochemical reactions caused by the disturbing effects of the water in the drill hole through which they are generally measured. Observations by the author in wells empty of water and in a mine shaft suggest that potential differences between sandstones and shales are natural and specific properties of the rocks, although they are modified to measurement by the disturbing effects of the water in the drill hole. The cause of these potentials probably is to be sought in the relative polar adsorptive capacities of quartz and clay particles.

Jan 1, 1944

By D. H. Davis

There are two general types of oil flotation processes, froth and bulk-oil. In froth flotation, the coal concentrates are removed in the form of a froth or foam composed of air, liquid, and solids. Mechanical or pneumatic agitation of a coal slurry with suitable frothing agent causes a selective action of the bubbles to the coal particles which are carried to the upper portion of the pulp in the flotation cell; the refuse is wetted by the water and does not rise with the froth, but goes out as tailings. The other type of flotation process, bulk-oil, consists of thoroughly mixing the slurry or pulp with 30 to 50 pct of its weight of oil. The coal agglomerates with the oil and drops to the bottom of the cell while the refuse is wetted by the water and is carried away in suspension. The concentrate granules may be screened and drained to 12 to 15 pct moisture. The minus 200 or 300-mesh is very effectively treated by this process. The Trent process is a bulk-oil type which has been used for coal cleaning on a commercial basis, but its use has been discontinued in this country. Froth flotation of bituminous coal should be subdivided into two distinct fields: (I) separation of a dry coal product such as recovered from an aspiration system; (2) separation of a minus 48-mesh slurry such as produced from a thickener in a wet cleaning plant. The capacities, performance, and general operating characteristics are very different in these two fields. The recirculated slurry in a washery becomes oxidized and is much harder to treat than a dry dust. It is difficult to clean a slurry containing an appreciable percentage of plus 48-mesh without also floating some high-ash clays minus 200-niesh in size. On the other hand, while working with an aspirated dust, good results have been obtained in floating coal as coarse as 3/16-in. Because of the relatively low capacity of flotation machines as compared with conventional fine-coal cleaners .and because of the greater quantity of reagents required to float coarse coal, there is usually no point in considering flotation on bituminous coal for anything coarser than approximately 48-mesh. In some coal-cleaning plants, good separations are being made down to 80 or even 100-mesh by a less expensive system of coal cleaning than flotation. The Pittsburgh Coal Co. carried out extensive tests on laboratory batch machines and on small units of both pneumatic and mechanical agitation types from 1930 to 1935 and have operated six, eight, and then twelve mill-size mechanical subaeration cells from 1932 to 1944 This paper will deal with some of the operating phases and results of coal-flotation practices as derived from this experience, and more specifically with the flotation practice at the Champion No. I preparation plant. The experience gained from the research and initial experimental work contributed greatly to the successful operation of the mill-sized flotation units at Champion.

Jan 1, 1949

By F. W. Schremp, J. W. Chittum, T. S. Arczynski

This paper describes a laboratory study of causes of external casing corrosion and the test work that led to the use of oxygen scavengers to prevent this attack. External casing failures are classified as water-line, casing-casing, collar and body failures. A corrosion mechanism based on principles of differential oxygen availability is developed that is consistent with facts known about each kind of failure. The field use of oxygen scavengers is depicted as a direct result of the laboratory study. A part of the paper is devoted to reporting on the field use of hydra-zine to control external casing corrosion. Results of field measurements made over a period of several years are presented as evidence of the efectiveness of the hydrazine treatment. The first conclusion reached is that the use of hydrazine materially reduces the cathodic protection requirements for treated wells. This result is interpreted to mean that a reduction is taking place in the amount of corrosion on the casing. Results indicate also that hydrazine shows its greatest usefulness within the first 12 to 18 months after a well is completed when pitting corrosion is likely to be most active. INTRODUCTION According to surveys sponsored by the National Association of Corrosion Engineers,' the cost of repairing casing leaks caused by external corrosion may exceed $4 million per year. In addition, well damage and lost production resulting from casing leaks probably costs the petroleum industry an additional $5 to $6 million per year. Concern about the cost of external casing corrosion led to an extensive laboratory study of factors causing this external corrosion and to the development of a new approach to its prevention. This paper presents a discussion of various causes of external casing corrosion, details of laboratory studies and the results of the field use of an oxygen scavenger in well cementing fluids to prevent the external corrosion of oil-string casing. Measurements on test wells over a period of several years show that cathodic-protection current requirements are greatly reduced when hydrazine is used in cementing mud. Reduction of current requirements can be interpreted to mean that removal of oxygen by hydrazine has greatly suppressed corrosion cells on the external surface of the casing and thereby, has reduced corrosion. To date, hydrazine has been used by the Standard Oil Co. of California in more than 200 well completions. KINDS OF CASING FAILURES A survey of a large number of casing leaks disclosed four types of external casing failures — water-line, casing-casing, collar and body failures. These types are identified largely by their location on the casing. Water-line failures are found just below the surface of water or mud in the casing annulus. Casing-casing failures occur on the oil string just below the shoe of the surface string. Collar failures are found in the threaded ends of casing joints where they are screwed into casing collars. Body failures may occur at any point on the body of a casing joint. Ex- amples of each kind of failure have some of the general characteristics that are shown in Fig. 1. Water-line failures usually result in the circumferential severance of an oil-string casing. The corrosive action causing a water-line failure usually is sharply defined and is limited to a short length of the casing. Casing-casing failures usually are accompanied by pitting corrosion distributed around the oil-string casing for distances up to 100-ft below the shoe of the surface string. Casing-casing failures may also sever the casing. Collar failures seem to start on the first thread at the bottom of recesses between collar and casing joint. Corrosion proceeds across the threads by what appears to be a normal pitting mechanism. Both casing and collar are severely attacked. Body failures are the result of highly localized pitting at any point on a casing wall. Besides the pit that perforates a casing, a large number of other pits usually are found along one side of the casing joint. The pits occasionally are filled with corrosion products consisting largely of oxides and sulfides.' Frequently, the mill scale is largely intact on the rest of the casing. Examination of a casing failure does not always reveal the cause of the failure. Frequently, the necessary details are destroyed when the failure occurs. For example, formation water flowing through a perforation at high velocity may enlarge the hole and destroy any remaining evidence of the cause of the failure. One way to obtain undistorted information about a failure is to study the nature of other pits on the casing in the vicinity of the failure. A study of such pits frequently suggests that they are characteristic of an attack resulting from the differential availability of molecular oxygen.

By AIME AIME

ORGANIZATION of The Federated American Engineering Societies was effected at the organizing conference of national, local, state and regional engineering and allied technical organizations at the Cosmos Club, Washington, D. C., June 3 and 4. Thus is brought into being the greatest national engineering society in the world. The object of the organization is to further the interests of the public through the use of technical knowledge and engineering experience, and to consider and act upon matters common to engineering and allied technical professions. Prominent engineers from all parts of the country, representing more than 75 engineering societies, with an aggregate membership of more than 125,000, participated in the organization. The constitution as adopted by the conference, calls for the creation of s managing body to be known as the American Engineering Council, and its executive board. The belief was expressed that the entire organization would come to be spoken of as the American Engineering Council. The council is to coordinate the activities of state councils and of local affiliations whenever these activities are of national or general importance or may affect the general interests of engineers. Representation in the council is to be according to membership of the component societies.

Jan 1, 1920

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been calculated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware, no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By Y. Nakada, U. F. Kocks, B. Chalmers

The stress-strain behavior of the gold single crystals in easy glide was found to be affected by the specimen dimension which is parallel to the projection of the Burgers vector of the primary-slip system. The larger this dimension is, the larger is the slope of easy glide. Previously severa1 investigators attributed the size effects to either the existence of surface films or the grip constraints. However, in this experiment both of these possible causes were not present. It is proposed that the length of slip path (defined as the crystal dimension parallel to the Burgers vector of the primary system) is the controlling factor in the size effect observed in gold. THERE are many possible effects of the specimen dimension on the work-hardening behavior of single crystals: grip effects which prevent end regions of the crystal from deformation or rotation; effects of a surface film, for example a coherent oxide; effects of a subsurface layer of accidental or intentional

Jan 1, 1964

By M. Cepak, K. Donovan, W. G. Pariseau

This paper examines the difficulties of applying the finite element (FE) method of analysis to quantitative design of cable bolt systems. Cable bolt systems are in general use for ground control in VCR (Vertical Crater Retreat) topes throughout the world. However, despite their widespread use and importance, design of cable bolt systems is highly subjective. Two difficulties with the FE approach are examined: (i) the use of standard elements with a high aspect ratio (slender elements) to represent bolts, and (ii) the influence of cable bolts on hanging wall stability of a VCR study stope. Analysis results indicate that the use of slender elements for bolts is practical in large scale finite element analyses of VCR stopes. There are significant advantages in this approach to the engineering design of cable bolt systems in underground mining.

Jan 1, 1984

By Wm. Terry Siemers, Frank E. Kottlowski, George S. Austin

The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded $227 million. The state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fuorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand. Non-metallic resources are distributed throughout the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9% to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1982

Jan 1, 1919