Search Documents

By Eric Jette

IN order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be .added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a 'reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time' efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned.

Jan 1, 1931

By R. L. Dalton, L. A. Rapoport, C. W. Carpenter

Procedures have been developed to study the performance characteristics of unconfined pilot water floods using scaled laboratory models. The effects of operating conditions on pilot performance for variozrs well patterns have been investigated. The limitations of the laboratory model studies are outlined. Relationships between the oil recoveries of pilots and large-scale floods have been established. The applications of model studies to the prediction of large-scale waterflood performance and pilot flood design are discussed. INTRODUCTION Pilot water floods are undertaken to evaluate operational procedures and to gain advance information about the performance of an extensive water flood. In general, however, the performance of a pilot flood is not directly indicative of what can be expected from a large-scale pattern water flood. This difference stems from the fact that the over-all flow configurations are not the same for the two systems. A water flood normally consists of an array of identical well patterns. In such an array, the perimeters of the well patterns are axes of symmetry and act as impermeable boundaries. Thus, an extensive, pattern water flood can be visualized as a repetition of "confined" floods. In contrast, a pilot water flood involving only one or a few well patterns is "unconfined". Here the well patterns are not balanced by other flood units; hence, the perimeter of the pilot area does not act as an effective boundary. Accordingly, only a portion of the fluids injected (and also of those originally contained within the pilot area) is captured by the producers of the pilot. The rest escapes into the surrounding reservoir. This usually causes the amounts of oil and water produced in the pilot to be different from those recovered by a producer in an extensive water flood. Moreover, the recovery observed in the pilot can be expected to be greatly influenced by operating conditions, i.e., by the bottom-hole pressures at the injection and producing wells. The above considerations show that full utilization of pilot test results and reliable prediction of large- scale water floods require a knowledge of the relationship between the recovery performance of confined and unconfined well patterns. To date, only limited basic information is available on the behavior of pilot water floods. Craig, et al,' have investigated the effects of initial gas saturation, oil-to-water mobility ratio, and well damage on the oil recovered from a single, "normal" five-spot pilot pattern (Fig. 1). Rosenbaum and Matthews2 studied the effect of initial gas saturation and mobility ratio on the ratio of production rate to injection rate for various groupings of five-spot patterns. Paulse113 investigated the effect of mobility ratio and distance from the pilot to the edge of the reservoir on the areal sweep in a single "inverted" five-spot (Fig. 1). However, none of these studies considered the effect of operating conditions on pilot flood behavior. Moreover, hardly any of the work to date dealt explicitly with the oil-recovery performance of the pilot floods. The purpose of this paper is to introduce the concept of interrelation between pilot flood behavior and operating conditions, to illustrate this interrelation by means of experimental data and to compare the recovery performances of dif-

By Charles White Merrill

Money is one of the most .pervasive elements in human life. The compensation for a workman's daily efforts is expressed as a wage and is measured in money. What an individual may consume depends largely on his income which also is expressed in terms of money. If he would start an enterprise its size would be determined in large part by the amount of money available for capitalization and its success would be measured in net income expressed in money. In short, the most widely used common denominator for comparing merchandise, real property, jobs, enterprises, gross national product, or personal success is money. Despite this use of money by almost everyone past infancy to express his appraisal of the in- numerable values he sees around himself, the complexity of the device called money makes its nature and workings a mystery to most users. Some of the difficulty in understanding money results from the fact that it has three distinct but interrelated functions: (1) a medium of exchange, (2) a unit of account, and (3) a store of value. In many statements about money the discussion moves from one function of money to another without the speaker or the listener recognizing the changes. For example, the housewife says "We took the money we had saved up to make the down payment and after twelve monthly payments the television will be ours." When this housewife spoke of "saving up the down payment" she referred to money in its function as a store of value; when she spoke of "the down payment" she was using money as a medium of exchange; and when she referred to the "monthly payments" she spoke of money as a unit of account. Another cause of confusion in understanding money is its paradoxical nature in that it represents both the power to produce and the power to consume. For example, when the rich uncle dies one nephew may regard his inheritance as an opportunity to buy a farm and leave the ranks of the wage earners to become an independent producer, whereas the other nephew may regard his portion as the means of living in complete leisure as a pure consumer.

Jan 1, 1959

By F. Morgan, M. Muskat, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By M. Muskat, F. Morgan, R. G. Russell

Core experiments with radioactive tracers are reported in which an artificial radioactive material, radiovanadium, was used in aqueous solution in a study of the mobility of connate water. Sandstone cores saturated with active water were first oil-flooded to simulate virgin sand conditions in which the pores are filled with oil and connate water. They were then subjected to flooding with inactive water. Measurements were made of the activity of various portions of the effluent as well as the activity of the core after the flooding process was completed. In additional experiments the distribution of activity along the core was measured during the flooding process. In still other experiments direct flooding tests were made on cores fully saturated with active water. In all cases it was found that after injecting into the core a volume of inactive water equal to a pore volume, the effluent contained more than 80 per cent of the active content originally in the core. It is felt that these results imply a high degree of mobility of the connate water when subjected to flooding, although at least a partial contribution of the effect of tracer transfer within the core cannot be definitely excluded. The implications of this result with respect to water-flooding, core analysis and electric logging are discussed. A better approach to determining the connate water saturation of oil-producing rocks, by measuring the fluid content of core samples at the surface, is by the use of crude oil or oil-base muds as the coring fluid. Although water flooding is of considerable importance in the recovery of ail, comparatively little is known with certainty about the role played by the connate water during the operations. Two possibilities exist. Either the connate water is retained in the formation while the flood water sweeps past, or it is pushed along to a greater or lesser degree by the flood. Thus far no explicit recognition in terms of quantitative studies appears to have been given to the displacement of connate waters by the intruding extraneous waters, although such a possibility might be important in determining the efficiency of the oil -displacement process in water-flooding operations, especially in argillaceous rocks. On the other hand, it is a common observation that the first water produced with the oil as a result of water-flooding is definitely saline.*.' Similar questions regarding the mobility of the interstitial water arise in the quantitative description of the advance of edge-water drives. In the interpretation of the water saturations determined from core analyses, when coring with water-base muds, it is generally assumed that the drilling fluid merely adds to the connate water without displacing the

Jan 1, 1947

By H. G. Warren, E. W. Hough

Correlation of interfacial tension of the methane-n-pentane and methane-n-decane systems was made by Hough and Stegemeier by the use of the Weinaug and Katz equation. The methane-n-heptane and ethylene-n-heptane systems were investigated by the authors. Additional systems taken from the literature were the me thane-propane system by Weinaug. and Katz, the methane-n-butane system by Pennington and Hough, and the n- butane -carbon dioxide system by Brauer and Hough. These systems were analyzed by the Weinaug-Katz equation and the Sugden equation on the IBM 1620 11 computer using a regression analysis program. Parachor and exponent values for each component and system were determined. The experimental work was close to the critical point of the light component in the n-butane-carbon dioxide and ethylene-n-heptane systems, between the critical points of the light and heavy components in the methane-n-pentane, methane-n-heptane and methane-n-decane systems, and close to the critical point of the heavy component in the methane-pmpane and methane-n-butane systems. An empirical formula was developed to find a value of the constant B in the Sugden equation for binary hydrocarbon systems from the parachor values of the two components. Interfacial tension for binary hydrocarbon systems was found to be a direct function of liquid-vapor phase density difference in the same manner as a single-component system. DISCUSSION Interfacial tension may be defined as the measure of the specific free surface energy between two phases having different compositions.1 The interfacial tension (IFT) for a binary system may be predicted for any temperature and pressure if the

Jan 1, 1967

By T. G. Madgwick, A. Beeby Thompson

FoR more than 2500 years, natural gas issues in the Surakhany district of the Apsheron peninsula were the object of pilgrimages by fire worshippere and Hindoos from Burma and India. Even as late as 1890, Hindoo priests conducted ceremonies in a temple at Surakhany, which probably replaced a more ancient one; but later, the visits of the pilgrims were prohibited in order to check the spread of Asiatic diseases in that region. For centuries, limited supplies of oil have been abstracted from shallow excavations in the Caspian oil belt and dispatched into the interior of Asia and elsewhere for medicinal and industrial purposes. Statistics show a yield of 37,400 bbl. in 1863, but only since 1869 has there been serious development; in that year the yield was 203,000 bbl. At that time, hand digging was supplanted by drilling, and the enormous wells that resulted from tapping sources hitherto beyond the reach of operators completely demoralized the industry for a time, owing to inadequate outlets for the products. The early activities in this area were greatly hindered by annoying taxation, monopolies, imperial land grants, etc., but when these were revoked or adjusted, in 1877, the industry sprang into prominence and, between 1898 and 1901, the Baku fields produced practically one-half of the world's supply of oil. Within a few miles of Baku lie the two richest oil fields in the world; viz., the Balakhany-Saboontchy-Romany and the Bibi-Eibat, the latter constituting almost a suburb of the city. For many years the gasoline obtained in the refineries of the Baku area was burned in pits, being considered an undesirable product, and until 1870 the residue also was destroyed, its value as a fuel not being recognized. Kerosene was the main product sought by the refiners. It was shipped across the Caspian Sea and up the Volga to the industrial centers of Russia. Only on the completion of the Baku-Batoum railway did the Baku oil fields secure important commercial communication with the outside world through the medium of the Black Sea. The first tank steamer was successfully launched on the Caspian in 1879, by Messrs. Nobels, for transporting oil in bulk instead of in barrels. In 1905, an 8-in. pipe line to Batoum was completed; this was capable of transporting to seaboard 8,000,000 bbl. of kerosene per annum.

Jan 1, 1921

By R. L. Rickett, W. C. Leslie, W. D. Lafferty

Notch toughness of 0.10'pct C steels, rimmed or killed, is improved by holding the steel at a temperature just above the Ae,, followed by air cooling. The improvement can be gained without apparent change in gross microstructure or hardness. The limits of the process have been determined and some possible reasons for the observed effects are discussed. The results appear to indicate that the current theories of transition temperature are inadequate. THE effects of gross microstructural variables (ferrite grain size, austenite grain size, type and distribution of carbides) on the notch toughness of mild steels have been the subject of many investigations.'-' The results indicate that increasing ferrite grain size raises the notch-impact transition temperature. The transition temperature also rises with increasing size of pearlite colonies and with increasing prior austenite grain size, but these factors are not independent of ferrite grain size. The effects of gross composition of steels have also received considerable attention. As a result, manganese, nickel, aluminum, and silicon are known to improve the notch toughness of mild steels. The other elements that have been investigated—carbon, nitrogen, boron, copper, chromium, molybdenum, phosphorus, sulfur, titanium, and vanadium—reportedly are either deleterious or have little effect on notch toughness. Despite this large volume of work, it is still not possible to predict the notch toughness of a mild steel from its microstructure and composition, even when these are supplemented by hardness and tensile tests. Steels with equivalent microstructures, but different thermal and/or mechanical histories, can differ in notch toughness. Such factors as type and distribution of precipitates, substructure, local variations in composition, or unrecognized variables, may be important in determining the notch toughness of mild steels. However, quantitative knowledge of the effects produced by these factors is almost completely lacking. In an effort to improve this situation, an investigation was begun to determine the effect of a very fine precipitate on the notch toughness of low-carbon steels. Aluminum nitride was chosen as the precipitate because of its presence in aluminum-killed steels, the ease of control of precipitation, and past

Jan 1, 1961

By F. Valton

(Read at the Wilkes-Barre Meeting, May, 1877.) IN the number of the Engineering and Mining Journal for April 7th, 1877, Mr. W. P. Ward, of Cartersville, Georgia, explains in a very interesting manner, the results he obtained in the manufacture of ferromanganese in the blast furnace. These results may be summed tip as follows : Production in the blast furnace of an alloy containing 67.2 per cent. manganese and 3 per cent. of carbon at most, with a utilization of the manganese amounting to 58 per cent. With the exception of the indicated proportion of carbon, which should be almost doubled to express the true state of facts, we would have had no observations to make on Mr. Ward's paper had he taken into account the results obtained in the same line in other centres of production. Before 1870, spiegel with 8 or 10 per cent. manganese only was known among blast-furnace products. In a journey to Sweden, in 1871, I ascertained that the Schysshyttan works manufactured regularly a spiegel with 18 per cent. manganese. Later, at the Vienna Exhibition, in 1873, the Sava and Jauerburg works, in Carniola, presented to the jury a ferromanganese, obtained in the blast fur-

Jan 1, 1878

By William N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are located in the south central section of Canada's Yukon Territory. The Yukon is sparsely settled, with a total population of less than 23 000. Wide seasonal temperature variations are experienced with extremes of 35º C and -57º C being recorded at Faro. The concentrator treats 9000 tons per day of a complex lead-zinc sulphide ore, employing conventional crushing, grinding and differential flotation to produce selective lead and zinc concentrates as well as a mixed lead/zinc (bulk) concentrate. The current operating practice and highlights of the eight years the concentrator has been in operation are reviewed. In addition, certain of the unique features and problems connected with plant operation in a remote northern location are discussed in some detail.

Jan 1, 1977

By William M. Newton, John E. Sherborne

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

By John E. Sherborne, William M. Newton

The relation between the properties of electric logs and the fluid used in drilling a well is briefly discussed in this paper, and the fact that the resistivity of the drilling mud and its filtrate can appreciably affect such logs is shown. Apparatus was designed and a procedure established to determine the effect of various factors on the resistivity of drilling mud. Five muds commonly employed in California were tested and the following observations were made: I. The effect of raising the temperature from 80°F. to 180°F. is to decrease the resis-tiviiy of the mud or filtrate approximately 50 per cent. 2. The resistivity of the mud in most cases closely approximates that of its filtrate. 3, The change in the resistivities of muds caused by the addition of chemical is not the same function of the amount of chemical added for each mud. 4. The effect produced by increased sodium chloride content is to reduce markedly the resistivity of the mud and its filtrate. 5. Weighting materials, such as Baroid and limestone, tend to increase the resistivity of drilling mud. 6, Cement and counteracting reagents reduce mud resistivity. Introduction During recent years, the practice of "electrically logging9' a geologic formation by means of a system of electrodes lowered in a well bore has provided data of inestimable value concerning the nature of the sediments penetrated. Thus, it is generally possible, by means of electric logs, to distinguish readily the differences between shales, sandstones, cherts, limestones, and other rock forms. The distinguishing characteristics recorded in this manner have made possible long-range and closely detailed mapping and visualization of deeply buried structures1-5 to a degree not to be obtained with a reasonable expenditure of money by any other means at present in use. Besides being of value in correlation work, electric logs have been found, in some instances, to be useful in estimating the nature of fluid contained within the pores of a rock. In special cases, even the relative permeabilities at different horizons have been determined.6 That electric logs should reflect in some measure such physical properties of rocks as porosity and permeability and, in addition, give rise to data pertaining to the fluid content of rock interstices, becomes evident when the conditions giving rise to the electrical phenomena measured are known. However, it is not the purpose of this paper to review the present status of electric logging; rather, the reader is referred to the papers cited on page 220 for the principles and practice involved. Importance of Drilling FLuid in Electric Logging Because the drilling fluid must be the medium through which the electric logging device is made to traverse the formations penetrated by a borehole, and since, in general, the drilling mud completely surrounds

Jan 1, 1942

LANS are underway for the annual meeting of AIME, to be held in New York, February 17 to 21. The technical program includes meetings of all divisions of all three branches, Mining, Metals, and Petroleum. The bulk of the technical sessions will be held at the Statler Hotel, and the annual banquet will be held at the Waldorf-Astoria, Wednesday evening, February 20. The technical program of the Mining Branch activities is included in this issue. While it is not complete in every detail, it shows general interest groupings as well as subjects to be discussed. The program for each division is shown separately to facilitate following the activities of these special interest groups. Then, after a full scale and possibly somewhat strenuous technical meeting, a post-meeting feature will appeal to many of the members. A restful cruise to Bermuda and Nassau is offered at special rates to AIME members and friends. The schedule is a 3:00 pm departure from New York on the Queen of Bermuda on Saturday, February 23; arrival at Bermuda at 7:00 am Monday, February 25; arrival at Nassau at noon, Wednesday, February 27; and the trip ending again in New York at 9:00 am, Saturday, March 1. Rates begin at $202.10 per person, with higher rates depending upon accomodations desired. The base rate includes outside room with private bath and all meals, as well as Federal, Bermuda and Nassau taxes. Reservations for the trip should be made immediately through Leon V. Arnold, 36 Washington Square West, New York 11, who is in charge of arrangements.

Jan 1, 1952

By Earl Oliver

This paper is based on the formula that the petroleum industry is sick—find the cause, eliminate it, and the industry will get well. There is perhaps no difference of opinion that the cause is overproduction, actual or potential. But that, again, is a result rather than a cause. The problem is to study the influences that serve to keep production and consumption out of balance. Production control is a popular theme and a natural one at this time when the whole world is unstable; but production control in its popular sense means little more than the application of emergency measures while danger threatens. Economists differ as to the effectiveness of these, most of which are designed to alleviate and not to cure, but we assume there are none who question the wisdom of promoting conditions under which economic forces are permitted to operate freely in bringing about stable conditions. The petroleum industry suffers from two classes of economic ills that serve to promote overproduction; namely, those which are common to all industries and those which are peculiar to this industry. It is of the latter I wish to speak. Strange to say, government is responsible in large part for this latter class of ills that affect the petroleum industry and we are coming to recognize that only through the assistance of government can they be corrected. Instability of the petroleunl industry, in so far as human agency was involved, had its inception in 1875 when a Pennsylvania jurist, called upon to make a decision for which there was no precedent and fancying he noted some resemblance between the so-called fugitive nature of oil and gas and that of wild game, made mention of that resemblance. Other courts being impressed by the analogy enlarged upon it, and gradually fixed upon oil and gas a legal status in certain important respects similar to that of wild game. Although later the courts abandoned this analogy, certain practices that developed out of that early concept have continued to this day and are largely responsible for the industry's present plight. Thus, instead of ownership in place that is characteristic of private property generally, the law of capture was applied to oil and gas. Now, the rapid and wasteful depletion of game

Jan 1, 1932

By A. J. Sinclair

Sampling methods for feasibility studies are dependent on geological characteristics of the deposit being evaluated. A preliminary geostatistical study is required, taking into account autocorrelation aspects of variables under study in order that sample plan design can be optimized to produce grade and tonnage estimates within stipulated error limits. In general, regular sample distribution is to be aimed for, and regular sample lengths (from drill core or cuttings, for example) are preferred in order to facilitate statistical analysis. Sample plans are modified and improved (either technically or economically), as a sampling program proceeds and additional information is obtained. Bulk samples for metallurgical testing can be evaluated in terms of the variance shown by all such samples in a deposit and the internal variability of grade. Attention to these sources of variability will ensure proper evaluation of pilot test results from bulk samples. In addition, a general mineralogical study of a deposit is an important, often ignored, requirement in a more general but semi-quantitative evaluation of the representativeness of a bulk sample; and, moreover, provides information useful in optimizing plant design.

Jan 1, 1978

By J. P. Timmons, J. H. Moran, G. K. Miller, M. A. Coufleau

A prototype equipment has been designed and built for the digital recording of well logs on magnetic tape at the same time that the regular film recording is made. The format of the digital tape produced is such that it can be used directly at the input of the ZBM 704, 7090 or other models of ZBM computers which accept digital magnetic tape. This apparatus has been used for the experimental field recording of dipmeter tape logs which were subsequently computed by means of an ZBM 704 or 7090. In this paper the equipment and the digital tape are described briefly, and their application to the computer-interpretation of dipmeter data is discussed. A principal element in the interpretation of the dipmeter log is the correlation of the three microresirtivity dipmeter curves to determine the depth displacements between them. Several correlation methods for computer use are considered, with particular attention to their sensitivity to error and their consumption of computer time. The tape data were used to compute information content of the dipmeter microresistivity curves in terms of their frequency spectra. The results show that the sampling rate used in recording the digital information is quite adequate and illustrate a use of the digital tape in evaluating the characteristics of new tools. Some examples of field results are shown. It can be foreseen that, when digital tape recording becomes available for general field use, a whole new realm of possibilities will be opened up for the processing of other well logs through computations, which hitherto were not feasible because they were too laborious and time-con.sunzing. INTRODUCTION The last few years have seen a revolution in the design and production of data-processing equipment. Stored-pro-gram digital computers have progressed from a research curiosity to the basis of a major industry. There are now hundreds of such machines in daily use in the United States. With the acceptance of a technique that was, in fact, already clearly described by John von Neumann in 1945, the last decade has seen great strides in the development'of components, reliability, programming systems and, most spectacularly, in the sheer number of machines built and in use. In 1957 there were enough digital computers available to the oil industry to justify the suggestion that it would be worthwhile to investigate the possibility of using these machines in processing well log data.' The first result of this investigation was the appearance of what may be referred to as the input-output bottleneck. Well logs are customarily recorded on film. To get these data into a machine required then (and still does): a time-consuming semi-automatic reading of the film; conversion of the log data to digital form; and recording these digital data in some medium acceptable for computer input, such as cards, magnetic tape, or punched paper tape. However, the recording, reading, and re-recording could only result in deterioration of the data. Therefore, it was concluded that the fist step should be the development of a new, more direct recording technique supplemental to the film recording, which would provide easy access to the digital computer. There are many solutions to the problem of recording log data in an easily recoverable form. After careful consideration it was decided to adopt the boldest solution which, it was felt, was also the most elegant. It was decided to record well logs directly, in the field, on magnetic tape in such a way that this tape could be used without further modification as an input to the IBM 704 or 7090 computer. To realize practical field recording of magnetic tape logs, it became necessary to develop in a rather small package, an analog-to-digital converter, a tape recorder, and the necessary multiplexing and control circuits to allow the simultaneous recording of a multiplicity of logging signals. The magnetic tape recording was to be made simultaneously with the conventional logging operation in such a way as not to interfere with it. Along with the development of hardware, it was necessary to begin development of interpretation techniques and machine programs that would exploit the power of the digital computer. Here, again, there is a long list of possible applications. After much consideration it was decided to concentrate on the interpretation of the dipmeter log as a first application. It is the object of this paper to describe in some detail the developments sketched in the last three paragraphs.

By R. E. HORE, J. B. Tyrrell

IN the vicinity of Kirkland Lake, northern Ontario, several gold mines are producing, and three are at present being operated very profitably. At these three mines and on the adjoining properties east and west of them there have been important developments during the past year, and additional equipment has been installed to permit a large increase in output. At the end of 1924 the total production amounted to $13,688,600. For the year 1926 the production is estimated at about $19,000,000, and during 1926 the output should be much greater than that of 1925. The mines which are being operated most profitably and are producing a large part of the ore now being milled are the Wright-Hargreaves, Lake Shore and Teck-Hughes. Others which have contributed smaller amounts are the Tough-Oakes-Burnside and the Kirk- land Lake Gold mines.

Jan 1, 1926

By E. Stansfield, J. W. Sutherland

It is well known that the ash left when coal is burned is not the same either in chemical composition or in weight as the mineral matter originally present in the coal. This mineral matter has been referred to as "mineral impurity," "ash-forming constituents" and "corrected ash." The authors prefer the simple name used in the title and throughout this paper. The mineral matter in a sample of coal cannot be isolated unchanged and then weighed; but if the relation between the weight of mineral matter in the coal and the weight of ash remaining when the coal is burned can be ascertained, the weight of mineral matter in the sample can be calculated from the determined weight of ash. When the weight of mineral matter in the sample is known, the weight of pure coal can be found by subtraction. This pure coal must be the basis of accurate coal classification. W. F. Wheeler,l,3 W. Brinsmaid,2 S. W. Parr, and many subsequent workers have studied the relation between mineral matter and ash. Wheeler and Parr and others have deduced formulas for calculating this ratio, and used heavy-solution separations for checking the accuracy of their formulas. Brinsmaid hand-picked and analyzed two separate samples (and mixtures of these) and based thereon a graphical method of deducing the ratio. In the Fuel Testing Laboratories of the Scientific and Industrial Research Council of Alberta, a graphical method, based on heavy-solution fractionation of coal samples, has been used with marked success for the past 7¼ years for determining the mineral matter-ash ratio. This method resembles that employed by Brinsmaid in 1907.

Jan 1, 1930

By C. W. Beattie, R. L. Solter

ALUMINUM-KILLED, low carbon steel sheets are used extensively for severe deep drawing and other difficult forming operations. They usually, but not always, have a characteristic grain structure in which the grains are elongated both in the lengthwise and in the transverse direction. As described by Burns and McCabe,&apos; a typical grain in the plane of the sheet has its two axes in that plane from 1 Y2 to 4 times as long as the axis normal to the plane of the sheet. Rickett, Kalin, and MacKenzieZ have also reported on the recrystallization behavior of such steel. The contrast in grain structures of fully processed sheets of aluminum-killed and rimmed steel is illustrated by Figs. 1 and 2. The elongated grain structure of the aluminum-killed sheet is not developed on all heats or lots of this metal, and studies of the factors controlling and influencing its formation are reported in this paper. Jeffries and Archerb tate that unstrained grains are normally equiaxed, but exceptions are common. For example, if a metal containing a material mechanically obstructing grain growth is subjected to considerable working followed by thorough annealing, it may exhibit grains consistently elongated in the direction of working. Our experiments demonstrate that aluminum-killed, low carbon steel is such a metal, and that the substance mechanically obstructing grain growth is aluminum nitride. The effectiveness of aluminum nitride in inhibiting grain growth has been found to be influenced by the degree of cold reduction, the rate of heating in annealing, the thermal history of the sample before cold reduction, and the residual aluminum content. A correlation between grain shape and austenitic grain coarsening temperature also was indicated and additional experiments demonstrated that aluminum nitride is also the principal cause for the fine grain characteristic of aluminum-killed steels. Manufacture In conventional practice, aluminum-killed sheet steel is manufactured from a low carbon steel containing approximately 0.02 to 0.07 pct residual (HC1 soluble) Al. With the exception of certain samples containing greater or lesser amounts of aluminum, the steels used in these investigations were within the following composition range: C, 0.03 to 0.06 pct; Mn, 0.28 to 0.38; S, 0.017 to 0.032; Al, 0.03 to 0.06; P, <0.01; and Si, <0.01. Properly heated ingots are rolled to slabs about 4 in. thick. After surface conditioning, the slabs are reheated to about 2300°F and hot rolled continuouslv to strip about 1/10 in. thick. The strip rolling is completed at a temperature of 1550°F or higher, and the strip is coiled, usually at a temperature near the lower critical transformation. After cooling, the strip is pickled to remove oxide, cold reduced 40 to 70 pet to final thickness, then annealed to 1250° to 1350°F in 20 to 80 ton charges, the size of which results in slow heating and cooling rates. Effect of Cold Reduction According to Sachs and Van Horn,&apos; the deformations of the individual grains in rolling are similar to those of the total volume. Thus individual grains would elongate in rolling according to the amount of cold reduction imposed. This is true theoretically, but as cold reduction increases the individual grains tend to fragment, and measured grain elongations become less than theoretical. The amount of grain elongation may be described by a numerical rating based on grain counts made by the intercept method. Specimens are polished normal to the plane of the sheet, with the polished surface extending parallel to the rolling direction. After etching, grain intercepts are counted along a 50 mm line on a micrograph of suitable magnification. In random locations parallel to the plane of the sample 20 counts are made and 20 are made in the thickness direction of the sample the average count in the thickness direction divided by the average count parallel to the plane of the sample gives a numerical rating of the grain shape called grain elongation. For example, a grain elongation of 2.00 means that the average grain is twice as long as it is thick. The average of both counts may be converted to grains per sq mm by a nomograph relating intercept counts and grain count. By the same procedure the grain elongation in the plane of the sheet but transverse to the rolling direction may be determined, using transverse metallographic samples. A comparison of theoretical and measured grain elongation was obtained on an aluminum-killed

Jan 1, 1952

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximately 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;" in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process. developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description OF Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1949