Search Documents

By Ian Wark

SODIUM sulfide is used extensively to increase the recovery of oxidized copper and lead minerals by flotation, particularly when using xanthates as collectors. It is generally assumed that the sodium sulfide converts a film of the oxidized mineral to the sulfide, and that the xanthate, while not a very effective collector for the oxidized minerals, is a good collector for the sulfide. On the other hand, Taggart and his collaborators' claim that unless sulfide minerals are oxidized they cannot adsorb xanthates and do not float. Gaudin2 states that amyl xanthate, used in conjunction with sodium sulfide, gives better results than ethyl xanthate. Rabone3 and Mayer-Schranz4 agree that excess of sulfide functions as a depressant. Owing to the greater solubilities of the oxidized minerals than of the sulfides, the consumption of sodium sulfide is greater than that of most other flotation reagents, up to 10 lb. per ton of ore being used in some plants. Luyken and Bierbrauer5 recommend a water washing to remove soluble heavy metal salts; by this means sulfide consumption may be reduced. It was desirable to determine the limits of the sulfide concentrations between which contact is possible at surfaces of anglesite and cerussite in xanthate solutions. Similar determinations were desirable for the sulfide minerals with which the oxidized minerals are usually associated, since conditions should be chosen, if possible, so that the two types of mineral will float together. Because of the formation, especially in acid solutions, of hydrogen sulfide and of the hydrosulfide ion (HS-), the permissible limits of sulfide addition are obviously dependent upon the pH value. Sphalerite responds to ethyl xanthate only in the presence of an activator; for example, copper sulfate. It was necessary, therefore, to determine whether sodium sulfide interferes with the activation of sphalerite by copper sulfate. The combined effect of sulfide and copper sulfate was determined also for galena, chalcopyrite and pyrite.

Jan 1, 1936

By Charles H. Snow

The engineer has often to penetrate difficult or unknown regions. Mineral, irrigation, boundary and railway problems frequently necessitate journeys through, or long residence in, localities whence sustenance cannot be drawn. The selection and conveyance of provisions, outfit and implements thus become a matter of the first importance. Scientific skill, even of the highest order, is powerless unless supported by the proper appliances and foods. The advance of civilization favors the engineer, in that it is constantly enlarging his facilities and thus reducing his difficulties. Notwithstanding this fact, many are yet brought face to face with the problems considered in this paper. Distinction must be made between parties which are to be in constant or even occasional touch with a base of supplies, and those which will be for a long time dependent on their original outfit. Again, the requirements of a party on the march are different from those of a fixed camp. The district, season, cliinate, size and personnel of party also influence the character of the outfit. A party that is to be detached from its base of supplies for some time requires a greater variety of food than if it is to be gone for a short time. Much less in proportion need be taken where the journey is not long, so that privation is confined to a limited period. The ability to establish a fixed camp permits a larger outfit than would be possible if the camp mere to be moved from day to day. Transportation, climatic and other conditions are thus so varied that lists prepared for one work could hardly be applied to any other without some modification. Lists that have proved successful in some instances may, however, serve as bases to be added to, or otherwise altered, for the case in hand. The mistake usually made is in providing too large an outfit. Every emergency cannot be provided for; so that it is well to take, not what may be needed, but what cannot be spared.

Jan 1, 1900

By F. M. F. Cazin

Some twenty years ago the author of a book,* by which, for the first time, molecular action was made to account for nearly all phenomena in hydrodynamics, began his preface as follows: " It is contrary to all experience, that any branch of science should suddenly cut short its own line of reasoning, and drop all connection with its past, and yet as quickly re-establish itself on an entirely new basis. It is, therefore, not without justification that this book should be met with caution and even distrust." When the newly-discovered natural facts and laws presented in this paper were, in 1891, first laid before the officers of the American Institute of Mining Engineers, they might have been preceded by a preface to the same effect; and the expression would have found its justification by the actual experience these facts and laws met with. Since then, as the result of their publication in one of the most prominent

Jan 1, 1895

[ ]

Jan 1, 1938

With the exception of the mentions of coal in Illinois in the period 1660-1680, already referred to, the first coal found in the United States was in the James River, Virginia, field. In 1699 a large tract of .land above the present city of Richmond was allotted for a settlement of French Huguenots by the colonial, government, near the present Manakin, about fourteen miles above Richmond. They soon found coal, tradition says it was uncovered by a hunter pulling out a small tree in a. steel) bank near a stream, and Colonel William Byrd, F.R.S., the most prominent man of his day in the colony, wrote to the Colonial Council of Virginia, May 10 and 11, 1701: "The 10th of May, last., I with Coll. Randolph, Capt. Epes, Capt. Webb, &c., went up to the new settlements of ye French Refugees at ye Manaken Town.... We went tip to ye Cole, w'ch is not above a mile and a half from their settlement on the great upper Creeke, w'ch, riseing very high in great Raines hath washed away the Banks that the Coal lyes bare, otherwise it's very deep in the Earth, the land being very high, and near the surface is plenty of Slate.", Some of the Frenchmen were evidently familiar with the use of coal, as on May 22, 1702, "David Menestrier a black smith and one of ye french Refugees Inhabiting at Luciana Petitioning his Excellency that he may have leave to use ye coal mines lately discovered there for his forge his Excellency by and with ye advice of ye Council loth hereby give Leave to ye said David Menestrier to take what coales he shall want. out of ye said Coal mine for ye use of his forge according to ye Prayer of ye said Petition."2 There was some uncertainty about the grant of these lands to the Huguenots which caused the request for leave to use this coal, as a Virginia patent in its usual form allowed the owner to mine all minerals excepting gold and silver, which were subject to royalties for the Crown. After the visit to the coal above mentioned, "Wm. Byrd, understanding the land had not been granted to the French, took out a patent for 344 acres, including the same, (the coal) which patent was dated October 20, 1704".3

Jan 1, 1942

By Philip Davidson, Wm. B. Price

The object of this paper is to present, a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350" C. throughout the coininercial annealing range.. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: Alloy Copper, Lead. Iron. Nickel, ManGanese, Zinc, PeR Cent. Per Cent. Per Cent. Per Cent. Per Cent. PEr Cent. A................ 64.68 Trace 0.194 6.73 0.06 remainder B................ 65.82 1.27 0.227 6.17 0.06 remainder C................ 65.44 Trace 0.345 17.83 0.08 remainder D................ 65.60 1.08 0.238 17.77 0.06 remainder These alloys were lolled in accordance with regular mill practice to approximately No. 6 R. & 6. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 1/2 in. long by 1/2 in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 235 in. were also taken.

Jan 1, 1921

By Charles E. Nelson

THIS paper will outline briefly the practices commonly followed in this country for the melting and refining of magnesium and its alloys. The processes used for the various forms of primary magnesium, as jar as there are differences in the physical shape or behavior, will be discussed. The refining of general fine scrap or secondary magnesium was presented in an earlier paper and will be discussed briefly.1 Inasmuch as the use of fluxes is an essential part of all the melting and refining processes, this paper will deal with these in sufficient detail to point out their unique characteristics, in order to make their use more effective. The outline of this discussion will closely follow that of an earlier paper,2 with such changes and additions as seem necessary to bring it up to date. TYPES OF MELTING PRACTICE All melting and refining processes for magnesium and its alloys require the use of fluxes. These fluxes have a magnesium chloride base and other halide salts or oxides are added to give a density or behavior exactly suited to the particular melting practice. The successful handling of magnesium depends upon the proper use of the correct fluxes. There are four general methods of melting, summarized in the following paragraphs and treated in more detail in the section on Melting and Refining. Open-pot Method The open-pot method makes use of No. 230 flux, which provides protection during melting and a molten pool of flux into which the solid magnesium melts. The flux is stirred through the molten metal bath and agglomerates oxide or similar foreign bodies;, on quiet standing, it separates away, leaving the refined metal ball floating in an encircling layer of molten flux. It forms only a thin fluid film over the surface of the molten metal, which may be parted for hand-ladling processes and tends to cover the metal again after the ladle is removed. A very light dusting of the pot surface with fresh flux immediately after the ladle is removed is desirable. The open-pot method is used generally in the following processes: (I) alloying and remelting in the production of ingot, (2) in sand foundries for premelting and to a smaller extent for the production of small castings, (3) in permanent-mold founding for premelting and also direct ladling to castings, (4) for continuous methods of preparing metal in the production of billets or ingots from which wrought products are fabricated, (5) in general scrap recovery. Crucible Process The crucible process makes use of No. 310 flux, which has the property of being thinly fluid at the start, to provide protection and refining qualities, and then drys out or thickens after a time, leaving a protecting crust on the pot surface until the time of casting. At that time it can be readily skimmed off or held back, thus allowing the contents of the crucible to

Jan 1, 1946

By F. H. Deily, L. W. Ledgerwood, J. E. Eckel

A new method for drilling the earth's formations has undergone extensive laboratory and shallow earth drilling experimentation. This method, pellet impact drilling, uses the energy of a large mass of high velocity steel spheres to break and crush the rock. Pellets are confined to a region close to the hole bottom. Motive fluid for transporting and recycling the pellets is supplied by a modified jet pump. The pellet drilling method has inherent advantages over conventional rotary drilling. First, only a nominal amount of weight need be applied to the hole bottom. Second, only a very small amount of torque is required for bit rotation. Third, means are available for continual replacement of the cutter medium. The experimental laboratory work and analytical procedures necessary for the design of a pellet drill bit are described. In the laboratory program approximately half the effort was devoted to the development of a better understanding of the physical process, and half to the empirical testing of new bit configurations. Factors such as pellet size and velocity, jet pump characteristics and modifications, and power distribution are discussed. The design and construction of a pellet impact bit for drilling a 9 in. hole with 1 1/4 in. steel pellets are described. Drilling performance in representative rocks, hydraulic operating characteristics, and metallurgical problems are discussed. INTRODUCTION This paper discusses an attempt to reduce drilling costs through the development of a drilling method basically different from rotary drilling. Publications on drilling research indicate that the major effort on the part of manufacturers and operators has been confined to research in rotary, or rotary-percussion drilling. This applied drilling research has produced significant gains in drilling rates and bit life, but thus far it has failed to achieve any major decrease in general drilling costs. From recent statistics released by Drilling Contractors, it can be shown that the total cost of drilling an "average" well in 1953 was about 2 1/4 times the corresponding cost in 1935. Analysis of the costs will show that they are not due to inefficient field operations; they are due instead to both an inflated economy and greater "average" well depths. Diligent work by the industry has reduced the backlog of potential economic improvements in rotary drilling to a group of rather marginal prospects. Increasing depths and poorer quality reservoirs at these depths continue to make the drilling cost problem more acute. Hence, the aim of the work reported here was to develop a new drilling method not limited by the inherent characteristics of rotary drilling and thus capable of attaining further significant reductions in drilling costs. The effort devoted to research on this proposed new drilling method was of considerable magnitude and represented .in excess of 37 man-years of research. The affiliates of Standard Oil Co. (N. I.) sponsored this development program which was conducted by the Drilling Methods Section of the Carter Research Laboratory in Tulsa, Okla. The purpose of this paper is to

Jan 1, 1957

By Henry D. Hibbard

The finishing and casting temperature of steel is a subject concerning which there is so much to learn that some temerity is required to write about it. This paper is, therefore, suggestive rather than dogmatic, though the views expressed seem now to the writer to be correct; nevertheless, they may be modified by future developments or discoveries but until then may be of some utility, particularly to beginners in the making of steel. Consideration is limited to the temperatures of simple steels, also called carbon steels, which are those in which carbon is the only element introduced for the purpose of conferring desired physical properties. Alloy steels will receive attention later. Three things largely determine what a batch of steel really will be; via., composition, casting temperature, and rate of teeming. Each has its advocates as being the most important; but they are so interrelated that each must conform to or be right for the other two. When one is claimed to be the most essential to have right, that, probably, was the one that it was found had to be of a certain description, within narrow limits, to suit the already adopted variations of the other two; that is, it was the last of the three to be brought into line. The term "casting temperature" is rather indefinite as there ale several temperatures to which the term may be applied. Most writers who have mentioned casting temperature of steel have alluded to it in relative terms. The few who have given actual temperatures, including Langmuir, Burgess, Styri, and Bash, do not give full information about them. Their results demonstrate the efficiency of pyrometers used rather than aid the steelmaker. In order to understand and use the temperatures, one should know in each case what the steel was, the stage at which the temperature was taken, whether it was usual or not, and whether or not it was right for that steel at that stage. When these

Jan 1, 1925

By F. F. Aplan, E. C. Dowling, R. R. Klimpel

Numerous flotation models have been proposed in the literature. Thirteen of these have been applied to batch flotation data and evaluated with respect to one another using statistical techniques. Flotation tests were carried out on samples of a US porphyry copper ore (Pinto Valley, AZ). The ore was tested using various collector and frother systems to produce different time-recovery profiles. These were used to calculate flotation rate and ultimate recovery parameters for each model. The models were then evaluated statistically to determine the overall fit of the calculated to the observed data and to test the range of significance of the parameters in each model.

Jan 1, 1986

By H. R. Ogden, A. G. Imgram, D. N. Williams

The effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. Increasing the chromium, vandium, or aluminum content increased the strength of quenched structures with chromium being the most effective strengthener. Appreciable aging response was obtained with low chromium alloys, but high chromium alloys age softened rather than. hardened. High vanadium contents had a similar effect. Aluminum additions shifted the aging behavior toward that observed in lower chromium alloys, enabling high chromium alloys to be age hardened. DURING the course of titanium alloy development many a and a-ß alloys have been evolved to commercial status. However, only one all-ß alloy has achieved this same stature. This is the Ti-13V-11Cr-3Al alloy. It is characterized by a very sluggish ß-phase decomposition reaction such that very slow cooling rates can retain the 0 phase at room temperature. In addition, very high strength levels can be obtained by long-time aging treatments. Combinations of cold or warm working followed by aging produce even further improvements in strength. This paper describes the results of a research program in which the effects of composition on the mechanical properties and aging characteristics of several alloys in the Ti-V-Cr system, with and without aluminum modifications, were evaluated. EXPERIMENTAL PROCEDURES Electrolytically refined, high-purity titanium was used as the alloy base for these studies. Iodide chromium, electrolytically refined vanadium granules, and high-purity aluminum sheet were used as alloying additions. The compositions of interest were melted as 250-g ingots in a direct current arc melting furnace under a flowing atmosphere of argon. The ingots were hot forged to 3/4-in.-diam bars, vacuum annealed for 6 hr at 1800°F to reduce residual hydrogen content, and then hot swaged to 1/4-in.-diam rods. Fabrication history, and interstitial analyses after fabrication are given in Table I. All specimens to be heat treated were sealed in Vycor capsules under a partial pressure of argon. Samples used to define the ß transus were quenched from temperatures ranging from 1350° to 1100°F after holding at temperature for 15 min. Samples for aging studies were quenched from above the ß transus temperature and then aged for up to 64 hr at 750°F and for 100 hr at 850°, 900°, and 950°F. The effects of straining prior to aging were also investigated. The results of these studies were used to select the heat treatments for the tensile specimen blanks. Heat treatments of the tensile specimens are described in Table 11. Alloys were aged after solution heat treatment or after solution heat treatment and cold swaging to 50 pct reduction in area. Standard 0.125-in.-diam tensile specimens were machined from the heat-treated blanks. All tensile tests were performed in a Baldwin-Southwark uni-

Jan 1, 1963

By Waldemar Lindgren

THE purpose of this paper is to present certain facts relating to Cordilleran differentiation and metallization. Theoretical discussions concerning the exact modus operandi of differentiation, the causes that led up to it, and the original distribution of the magmas have been omitted because the author feels that his knowledge is deficient. These subjects have been adequately treated in the admirable works of Iddings, Daly, Harker, Tyrrell, Shand, and Wolff. The facts here set forth seem to indicate that differentiation and metallization form one continuous process during the eastward movement of the magmas, culminating in the alkaline province of the eastern border of the Cordilleran Ranges.

Jan 1, 1933

By B. A. Eaton, R. H. Jacoby

This paper presents the depletion-performance correlations developed using data from PVT studies and well-completion tests of 27 rich gas-condensate and volatile-oil reservoir fluids. The PVT behavior for each fluid war determined experimentally in the laboratory, and the depletion performance of each fluid was then calculated. Well-completion test data consisting of reservoir pressure and temperature, initial total gas-oil ratio, and stock-tank oil gravity were used with the depletion-performance data to develop general performance correlations. Three correlations are presented. The first equation shows the empirical relation of gas in place per barrel of hydrocarbon pore space with reservoir pressure and temperature, and initial total gas-oil ratio. The second equation is the correlation of stock-tank oil in place per barrel of hydrocarbon pore space. The third equation relates stock-tank oil production (to 500-psia depletion pressure) with pressure, temperature and oil gravity. All three correlations are also presented in convenient graphical form. Gas production to 500-psia depletion pressure is approximately 92.6 per cent of the gas in place for each fluid, so no correlation was developed for gas production. INTRODUCTION The rate of discovery of shallow, low-pressure and low-temperature oil reservoirs in the United States has been declining in recent years. For this reason, the search for oil has gone to greater depths where high pressures and temperatures are encountered. A high-pressure and high-temperature reservoir is the environment in which many rich gas condensates and highly volatile oils are found. Because of this trend, the performance prediction of such reservoirs has become an important task of the reservoir engineer. The need and usefulness of a performance correlation based on field data that are available from the usual well-completion tests have previously been established. These earlier attempts have shown that the phase behavior of rich gas-condensate systems and volatile-oil systems can be correlated with fluid properties, pressure and temperature. However, very little information on gas-condensate depletion performance5 was available at the time of these earlier attempts. The availability of more recent data has made possible the development of an improved correlation. The data, as listed in Tables I and 2, are for 25 gas-condensate and two volatile-oil systems that were studied. The problem was to correlate the data for in-place fluids and the production data with the initial total gas-oil ratio, initial reservoir pressure and temperature, and stock-tank oil gravity. These correlations were obtained by multiple regression analysis, whereby the data were fitted to an equation by the method of least squared error. BASIS OF THE CORRELATIONS 1. The data used in the development of these correlations were obtained from depletion-performance calculations6 and well-test or production measurements. 2. All of the independent variables used in the correlations are available from the usual well-test completion data. 3. The reservoir volume considered is 1 bbl of hydrocarbon pore space (HCPS). 4. The gas-oil ratio used is the total standard cubic feet of gas (at 14.7 psia, 60F) coming off the entire separator train per barrel of stock-tank oil. This minimizes the effect of separator conditions which might vary from system to system. 5. The correlated pressures are the actual reservoir pressures which might or might not be the saturation pressure of the reservoir fluid.

Jan 1, 1966

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By C. B. Gillson, Henry Fay

For several years past, investigations on the chemistry of tellurium have been carried on in the laboratory of this institution. The methods of preparation of pure telluriumf and the estimation of tellurium‡ have been studied, and an attempt to determine the atomic weight of tellurium is now in progress. All these problems had been investigated, however, along purely theoretical lines; and it was thought desirable to study the more practical application of the metal, which can now be had in considerable quantities as a waste product in the refining of copper-ores. In its physical and chemical properties tellurium is very similar to antimony, and it was thought

Jan 1, 1902

Jan 1, 1923

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By C. M. Marquardt

Tramp iron and steel moving on a conveyor belt cause small currents to be generated in a coil situated in a strong magnetic field, which are converted to an alternating current and are amplified. The output voltage from the amplifier fires a thyratron with a relay in its anode circuit, which actuates a howler and simultaneously drops a spot of marker material on the belt. THE problem of tramp iron removal from moving ore belts is a long standing one. When heavy ore streams are carried on a belt, magnetic pulleys and strong surface magnets fail to remove tramp buried in the ore stream. Tramp iron buried in the ore stream cannot be pulled from the bed by surface magnets and is carried past the magnetic pulley by the falling ore stream. With the increased use of detachable bits the problem of the detection and removal of tramp has become more necessary and difficult. Several types of tramp detectors have been developed. It would serve no practical purpose here to review exhaustively the literature on the subject. Methods of tramp detection used are: (1) The magnetic method, wherein the small current generated by the magnetized tramp passing a Coil is used. (2) The unbalanced oscillator method wherein the tank circuit of a stable radio- or audio-frequency oscillator is unbalanced causing a change of frequency or a change in plate current due to changes in eddy currents, hysteresis, or dielectric because of the presence of tramp. (3) The bridge methods wherein the impedance of one leg of an alternating current inductive bridge is changed due to the presence of conducting tramp. Each of these methods of tramp detection has its field of usefulness. The second and third methods are excellent for oxide iron ores, coal, sand and gravel, grain, etc. However, these latter methods are not suitable for use on ores that contain rich conducting sulphides, since a large piece of pyrite or galena will cause the same detector response as a piece of tramp iron. At the Caselton, Nevada, plant of the Combined Metals Reduction Co., sulphide ores are treated; therefore, it was necessary that a tramp detector operating on only the magnetic properties of the tramp iron be used. Tramp iron detectors of this type operate on the principle that if a piece of tramp iron moves near a coil in a high intensity, steady magnetic field, the presence of the moving tramp iron causes the magnetic flux lines through the coil to change. This induces a mall current in the Coil. In series with the Coil is generally placed a relay sensitive to currents of 1 to 3 microamp. When the tramp iron passes near the coil the flux linkages change, causing this very sensitive relay to actuate. Since the contacts of such a relay are very small it must actuate a second relay capable of breaking a larger current

Jan 1, 1951

By A. S. Appleton, M. B. Bever, G. E. Dieter

A gold-silver alloy was deformed by explosive loading at shock pressures up to 510 kbars. The stored energy and hardness increased over the whole range of pressures; the largest rates of increase were observed between 120 and 150 kbars. In this range, markings rkavacteristic of defornation twins first appeared; higher pressures produced markings in all grains. These effects are compared with those of conventional deformation processes and are discussed in relation to probable structural changes. In recent years, increasing efforts have been devoted to the investigation of the effects produced in metals by the passage of high-intensity shock waves of explosive origin. By properly utilizing the energy released by the detonation of a high explosive, it is possible to generate pressure pulses of the order of 500 kbars and higher. (One kbar equals l0 9 dynes per sq cm or approximately 1000 atm.) The passage of a shock wave through a metal occurs at pressures which are very much greater than the yield strength. As the shock front passes a point in the metal, the pressure rises almost instantaneously, and continues to act at the point for a few microseconds. Thus, metals subjected to explosive shock loading experience a nearly instantaneous increase in pressure, and a subsequent release of pressure, which is almost as rapid. Under these conditions mechanical twinning and shear transformations occur readily. smith1 has investigated the metallurgical changes in copper and iron resulting from exposure to explosive shock waves. He found an appreciable increase in hardness in both metals. In copper, a hardness greater than that resulting from 95 pct reduction in thickness by rolling was obtained, yet in the explosive deformation, the thickness of the specimen decreased only a few percent. After explosive loading, the micro-structure of copper showed markings characteristic of mechanical twins. The amount of stored energy resulting from explosive loading is of interest. Measurements of the stored energy of cold work as a function of strain, temperature, strain rate, and composition have been made with gold-silyer alloys deforyed by rolling, orthogonal cutting,3 drilling,4 filing, wire drawing, and torsion. The investigation reported here was also carried out with a gold-silver alloy and its results can be compared with those for the deformation of this alloy by more conventional methods. EXPERIMENTAL PROCEDURES An alloy containing 82.6 wt pct Au and 17.4 pct Ag was purchased in several batches from Handy and Harman Co., New York, as annealed rod 1/4 in. dim. The rod was cold-rolled to a sheet approximately

Jan 1, 1962