Search Documents

By G. Purcell, S. C. Sun

In an attempt to determine the relative collecting ability of 18-carbon fatty acids, studies were performed on rutile in aqueous solutions of the fatty acid soaps. The preceding article reported the electro-kinetic properties; this article outlines the flotation behavior. Results of these flotation experiments are described and correlated with the electrokinetic results. Recent studies of the electrokinetic1-4 and the electrochemical5,6 properties of a few solid-liquid interfaces have provided a better understanding of the flotation process. A number of investigators have attempted to determine the relative collecting ability of 18-carbon fatty acids, but their published results (even for the same mineral) vary widely. Such lack of agreement indicated a need for further investigation. In an effort, therefore, to resolve the problem, electro-kinetic studies were made on rutile in aqueous solutions of the fatty acid soaps. Following the determination of the electrokinetic properties, the flotation behavior of rutile was studied. Results of these flotation experiments are described in this paper and are correlated with the electrokinetic results. MATERIALS AND EXPERIMENTAL PROCEDURE Materials: Pure -28, + 35-mesh rutile crystals were used for all flotation tests, and nitrogen-saturated conductivity water was used throughout. Sodium hydroxide and hydrochloric acid were added for pH regulation. The methods of purification for these materials and the preparation of the soaps have been described elsewhere. 7 Equipment: A Hallimond cell, constructed in a manner similar to that described by Fuerstenau, Metzger and Seele,8 was used for the flotation of mineral particles; however, a coarse pyrex frit was substituted for the capillary. Procedure: Purified nitrogen was led through a two- way stopcock into a graduated cylinder partly filled with water. The gas forced water from the cylinder back into a header tank until the water level in the cylinder coincided with a predetermined mark. Reversal of the stopcock then allowed water in the tank to force nitrogen into the cell until the water in the graduated cylinder rose to a second predetermined mark. In this way a constant volume of nitrogen under practically constant pressure was used for each flotation test. However, the flotation time varied, depending upon the amount of mineral floated and the pH of the solution. Rutile crystals were transferred under water from a storage bottle by a glass scoop holding 1.7 g. Consistency of the scoop samples was good, varying from a low value of 1.67 to a high of 1.74 g. The water added to the conditioning bottle during mineral transfer was drained off, and then 2 cu cm of either hydrochloric acid or sodium hydroxide were added. The concentration of pH regulator was adjusted to give approximately the final soap solution pH that was required. The order of addition of reagents did not affect the results within the limits of experimental error. Soap solution of the required concentration was added under nitrogen pressure to fill the bottles completely. Conditioning for 1 hr was carried out on rolls rotating at 35 rpm. After conditioning, 2.5 cu cm of solution were run off into the container of a Beckman (model G) glass electrode pH meter. The electrodes were rinsed in this solution, which was then discarded, and 2.5 cu cm more were added for pH determination. The remaining solution and the mineral were transferred to the cell; care was taken to ensure that all mineral was washed out of the bottle by the conditioning solution. With the cell back in its flotation position the liquid just reached the desired level, and the test was started immediately. The amount of agitation in the cell was kept constant, and flotation was carried out without the use of a frother. In each series of ten tests one was run with no collector added to ensure that the mineral had not become contaminated, and two were conditioned at the same pH to check reproducibility. After each test the cell was dismounted, soaked in cleaning solution, washed in hot water and then rinsed with distilled water.

Jan 1, 1963

When Ponce de León landed in Florida in 1573 he was told of an Indian chief that possessed much gold. In 1576 Diego Meruelo obtained some of it from the Indians, and in 1579 Álvarez de Pineda reported that the natives wore ornaments of gold, which they obtained from the rivers. These statements all refer to the southern Appalachian region. The name is recorded in 1527; when Pamphilo Narváez landed at Tampa he heard that there was much gold to be obtained in a region named Apalache. * In 1564 René Laudonnière describes the methods used by the natives to win gold in the Apalatcy mountains.† However, no serious mining operations were undertaken until long afterward; the mining of gold in the Southern States may be said to have had its beginning when a nugget was found at the Reed mine, in North Carolina, in 1799. This nugget, which was of "the size of a small smoothing iron", was kept for several years before the finder learned what it was, but later more lumps, one weighing 28 pounds, were found in the same locality, and eager digging ensued. ‡ Thomas Jefferson, in his `Notes on Virginia', mentions the finding of a quartz specimen, not a nugget as is generally stated, that contained 17 pennyweights of gold; this was found on the Rappahannock river in 1782. §

Jan 1, 1932

By J. Geertsma

The relationship between porosity and the speed of propagation of acoustic waves in fluid-saturated porous rocks as measured by the Sonic log and by ultrasonic tecbniques is analyzed. Biot's continuum theory 1 is used to explain the difference in acoustic wave propagation between a dry and a liquid-saturated porous material. The porosity is a variable in this theory. However, the acoustic wave propagation in the dry rock depends too on porosity, and this dependence is not predicted by the theory. Frequently in dry sandstones, a nearly linear relationship between reciprocal acoustic wave velocity and porosity is observed in the low-porosity range. The physics behind this behavior is outlined. An empirical relationship of the form, 1/v = A + F, applies accordingly for many porous dry rocks, provided the porosity is the only variable. The presence of a liquid in the pores changes the value of B, and this change is found to be in agreement with the Biot theory. The time-average relation introduced some years ago2 results in an equation of the same type — 1/V = F/Vf + (1 - F)/Vr — but is not based on a sound physical picture. Still, this relation sometimes predicts approximately correct A and B values. Carbonate rocks with their complicated pore structures sometimes show a different relationship between wave velocity and porosity, unfavorable for log interpretation. Examples are presented. The simultaneous presence of calcite, dolomite and anhydrite, with their different grain densities and matrix compressibilities, complicates acoustic-log interpretation in carbonate rocks still further. Other complicating effects of acoustic-log interpretation are discussed. They are related to the influence of shale streaks and natural fractures on the average wave velocity observed by the logging tool and to the effect of adsorption phenomena on wave propagation in unstressed rocks particularly in sandstones. INTRODUCTION The velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity loggers of various d-sign may be used, for which velocity is defined as the. distance between a wave generator and a wave detector (one-receiver system) or the distance between two wave detectors (two-receiver system), divided by the shortest time required for a vibrational pulse to cross this distance. Velocity loggers ale used to assist in seismic prospecting, to differentiate between the various types of sedimentary rock layers, and also to determine rock porosity and pore fluid content. This paper is especially concerned with the relation between velocity and porosity and the effect of the pore fluid. Most velocity-log interpretation in terms of porosity is based on a formula advocated by Wyllie, et al,2 suggested earlier by Hughes and Jones,3 and known as the "time-average relation". This formula app1ies for a model consisting of a layered system of parallel alternating slices of a solid and a liquid, crossed by the wave path perpendicular to the interfacrbs. This must be an unsuitable model for the derivation of wave propagation properties of liquid-saturated porous media. It suggests that only rock matrix and fluid properties influence the wave velocity. The surprising fact, nevertheless, is that applications of this formula to clean sandstones under specific conditions (sufficient effective stress) results in porosity predictions which are close to reality. Other authors, such as Gassmann,4 White and Sengbush,5 Brandt,6 and Hicks and Berry,7 make use of more realistic models to arrive at a wave velocity formula for porous sediments. Their models consist of various liquid-saturated packings of frictionless spherical grains and are, therefore, also highly idealized. A number of experimental results obtained in the laboratory can be better explained with these model theories than by the time-average relation. A study of a general character, not depending a priori on a special model of the porous structure, was still lacking.

By M. R. Pickus, C. H. Mathewson

THE study of the plastic deformation and recrystallization of metals has been the subject of many investigations. In regard to the simple deformational processes, such as tension and compression, the early knowledge gained from studies of polycrystalline material has been supplemented by many significant researches on the behavior of single crystals. Unfortunately, this has not been true for more complicated deformational processes. As far back as 1927, G. I. Taylor1 wrote: It is impossible in the present state of knowledge to do more than give a possible reason why (face-centcred cubic) crystals set themselves with a (110) direction in the plane of rolling, and at right angles to the direction of rolling. The explanation of why the orientation of the crystal axes round the transverse direction is what it is, must be left till the distortion of metals, and particularly single crystals of metals in the process of rolling, has been studied in greater detail. That this gap in the systematic study of deformation and recrystallization has not yet been filled was indicated by C. H. Samans,2 who wrote in 1934 that "only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature." Of these four studies, only those of S. Tanaka3 and T. Sakao,4 both of whom worked with aluminum crystals, had quantitative significance. The other two, carried out by F. Wever5 and W. G. Burgers," were of a qualitative nature. It is our hope that the present investigation may contribute something to the knowledge necessary for a rationalization of the origin of rolling textures in terms of the known behavior of single crystals, and may add pertinent information concerning the recrystallization characteristics of deformed single crystals.

Jan 1, 1938

By B. G. Agnew

In evaluating fracture treatments, the need to answer such questions as "What zone or zones were actually treated?" and "What was the vertical extent of the treatment" is necessary, since determining effectiveness of the fracture treatwrent depends on knowledge of the reservoir portions stimulated and the vertical extent of the fracture system or systems. Injection of hot or cold fluids during fracturing operations will transfer heat to the surrounding formations and fracture faces mainly by heat conduction. Once injection ceases, temperature anomalies will develop opposite the zone fractured because the rate of temperature decay is less than that opposite zones heated or cooled by flow inside the wellbore or along the cement sheath. Thus, temperature surveys can he used to determine where fractures were generated outside the wellbore and to reasonahly estimate the vertical extent of the fractrires. This technique has been used successfully to evaluate over 344 fracture treatments at depths ranging from 1,500 to 15,700 ft. Examples of actual temperature surveys are presented to show how this method of fracture treatment evaluation can be used effectively and beneficially. INTRODUCTION Stimulation of producing or injection wells by fracturing is commonplace in the industry today. In evaluating these treatments, two basic questions which arise are "What zone or zones were actually stimulated?" and "What was the vertical extent of the treatment?". Knowledge of the reservoir portions stimulated and vertical extent of the fracture system or systems is vital to effect efficient and economical well completions and to assure maximum recovery from reservoirs. Not all fracture treatments are successful and many times the desired or anticipated results are not achieved. When this occurs, it is in most cases the engineer's job to determine why. The answer to this problem forms the primary basis for deciding whether to spend more money for development drilling and/or completion attempts or to forego additional expenditures to improve the particular zone. Also, knowledge of the reservoir portion actually stimulated is invaluable in planning future workovers. This is especially true in wells producing from reservoirs containing multiple porosity stringers or zones. For various reasons, all zones within a reservoir may not be perforated on initial completion with the thought of developing remaining zones through future workover operations. Because particular zones are perforated and fracturing fluid pumped down the wellbore, it cannot be assumed that all perforated zones are stimulated, and in turn drained. Occasionally, unperforated zones which are planned for future development are actually stimulated on initial completion. eliminating the need for future recompletion attempts or all zones perforated initially are not stimulated, thus requiring additional completion work to insure that these zones are adequately drained. In most cases, it is costly. if not impossible, to determine with assurance why a fracture treatment is unsuccessful after the job has been completed and the results tested. Further, unpredictable upper and lower fracture barriers. as well as possible borehole communications (cement channels), do not permit it to be taken for granted that the formation opposite the perforations is the only zone receiving the fracture treatment. Thus. evaluation of fracture treatments is necessary for efficient and prudent well completion practices and should be done simultaneously with the fracture job. Several methods have been used to locate fractured zones, all of which are based on detection of radioactive tracer materials added to either the fracturing fluid or the propping agent. These methods have been helpful in increasing knowledge of fracturing operations; however, they are seriously limited because of cost and inability to detect accurately radioactive tracer material more than a few inches away from the borehole. To develop a better diagnostic tool to pinpoint which zone or zones had actually been fractured, temperature surveys were run after fracturing with heated and cooled fluids. Significant temperature anomalies were found to exist opposite zones suspected of receiving the fracture treatment. From the analysis and examples to be shown, it can be seen that temperature surveys run in a stabilized wellbore several hours after a fracture treatment using hot or cold fluid will yield temperature anomalies which show the actual reservoir portion stimulated, the vertical extent of the fracture system or systems and a qualitative indication of the portion of fracture-fluid volume entering a given depth interval. The experience and illustrations used in this paper are based on evaluation of over 344 fracture treatments during the past three years using this diagnostic tool at depths ranging from 1.500 to 15,700 ft and fracture volumes ranging from 2.000 to 110.000 gal. Based on analyses of these temperature surveys, analyses of fracture gradients and evaluation of several open-hole packer impressions in the West Texas area,' vertical fracturing is the predominant mechanism and horizontal fractures occurred frequently, if at all.

Jan 1, 1967

By James S. Browning

The Bureau of Mines conducted laboratory and small-scale continuous tests of kyanite ore from Georgia and South Carolina to determine the technical feasibility of recovering commercial grade kyanite concentrates by flotation. The research indicated that combinations if sulfuric acid and petroleum sulfonate may be used effectively for flotation of kyanite from quartzite-kyanite ore. This report summarizes the results of these tests, and demonstrates the feasibility of producing commercial-grade concentrates with a high recovery of the contained kyanite. Extensive deposits of kyanite occur in the southeastern United States. The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate for many years at the present rate of consumption. According to Espenshade and Potter,' the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30% kyanite. The tonnage of kyanite-bearing gneiss and schist is much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina-South Carolina, and at Graves Mountain, Ga. Of the known deposits, only four were being mined for kyanite in 1 967. These deposits are near Farmville and Dillwyn, Va., Clover, S.C., and Washington, Ga.

Jan 1, 1970

Jan 1, 1918

By L. R. Mabson, F. M. Russell

INRODUCTION Roan Consolidated Mines Limited (RCM) operates five underground mines - Mufulira, Luanshya, Baluba, Chambeshi and Chibuluma (figure 1) . Associated metallurgical plants provide for the operations of milling, smelting two refineries for copper and a cobalt plant. Primarily a producer of high quality copper (242,000 tonnes during 1980) the Company is also the world's second largest producer of cobalt metal. RCM's remaining ore reserves at 31st March 1980 were 275 million tonnes at 2.84% copper. Monthly ore production is in excess of 1.2 million tonnes. Sublevel open stoping was the choice of mining method for the first underground operations on the Copperbelt for ore with dips steeper than 30 degrees. This was for use at the Roan Antelope mine, subsequently to be called Luanshya mine. The sublevel open stoping system was planned based on the methods used in many of the iron mines of Michigan and New York and in the copper mines of Tennessee. Peterson (Ref. 1) gave the following reasons for employing sublevel stoping, reasons which are still valid today: (1) the working place could always be barred and made safe, and the sublevel exit was always at hand; (2) the working conditions were similar day by day and drilling operations were repetitive; (3) pillar spacing can be varied as conditions demand; and (4) stoping operations could be shut down completely or opened up to full capacity at short notice, without affecting grade or causing wastage of reserves. Such was the success of the method that it was adopted as the basic mining method at all the RCM mines in their initial stages. Although cut and fill, block caving, and sub- level caving methods have been used, sublevel open stoping in its many variants still accounts for nearly 90% of total ore production in the Company. The following descriptions outline some of the applications of sublevel open stoping within RCM. LUANSHYA Geology There are two main ore deposits at Luanshya: the Roan (Luanshya Mining Area), in which mining began in 1930, and Baluba, in which mining production started in 1973 (figure 2). Both orebodies occur in synclinal and variably folded basins. These basins are underlain and completely surrounded by much older schists and granites. The ore formation, an argillite, lies near the base of the sediments and is underlain by conglomerates, quartzites and arkoses. Copper mineralisation is mainly found in two well defined zones, separated by a varying thickness of pyrite mineralisation. In the eastern part of the Roan deposit only the upper orebody is present, but west of 18 shaft and at Baluba the lower orebody predominates. Locally the subjacent quartzites of the footwall formation are also mineralised with copper. The copper mineralisation is found princi- pally as disseminated sulphides, mainly chalcocite, bornite and chalcopyrite. Near the surface the sulphides have been changed to oxides. At Baluba the cobalt mineral carrollite is found with the sulphides. Mining methods Sublevel open stoping is the basic mining method. In its standard form this method is best suited to steeply inclined orebodies, with simple structures and with a strong foot- wall and hangingwall. In recent years, as more complex folding and flatter dipping orebodies have been encountered, considerable variations have been introduced. Stope drilling is effected with drifters and extension steel.

Jan 1, 1981

By L. H. Dushak

DURING the war period of quicksilver activity there were a number of departures from what may be termed the classical quicksilver metallurgy. Attempts were made to beneficiate low-grade ores by gravity concentration and flotation; mechanical furnaces began to replace the Scott furnace and the vertical coarse-ore furnaces, and condensers of sewer tile and redwood tanks were used in place of the older brick and stone condensing chambers. Other developments that have occurred during the current period of quicksilver, activity are mainly in the nature of improvement and further refinement of those started during the war period. Each period of quicksilver activity has been accompanied by the proposal of various new processes, including wet methods for the treatment of quicksilver ores and innovations in furnaces, retorts and condenser equipment. As far as the author knows, nothing of economic significance in the way of "new processes" has been developed. There is in fact no real need for any essentially new process for the treatment of quicksilver ores; the direct furnace treatment is simple and inexpensive. Moreover, with fare exceptions, the quicksilver industry has no complex or refractory ore problems corresponding to those which are receiving more and more attention from metallurgists in other branches of the nonferrous field. Under these conditions improvements in quicksilver metallurgy must be looked for through the adaptation of current developments in engineering and metallurgy generally to the particular needs of quicksilver practice rather than through the invention of new processes.

Jan 1, 1930

By B. M. Larsen, K. Heindlhofer

THIS paper describes a relatively simple electrical apparatus that, through the close analogy between the flow of heat and of electricity, enables one to solve quickly and with satisfactory accuracy many complex problems in heat flow. This device, developed in 1935, has proved especially useful in the solution of certain practical problems relating to the design and efficiency of regenerators for an open-hearth furnace or coke oven, yielding within a few hours information that would take weeks or even months to acquire by mathematical1.2 or experimental3 methods of comparable accuracy. Its description now is prompted by growing interest in such analogues, as shown by several recent papers.4.5 The analogy between flow of heat and of electricity appears to have been recognized first by Maxwell who, in his famous Treatise on Electricity and Magnetism (1881) says: The analogy between the theory of the conduction of electricity and that of the conduction of heat is at first sight almost complete. If we can take two systems geometrically similar, and such that the conductivity. for heat at any part of the first is proportional to the conductivity for electricity at-the corresponding part of the second, and if we also make the temperature of any part of the first proportional to the electric potential at the corresponding point of the second, then the flow of heat across any area of the first will be proportional to the flow of electricity across the corresponding area of the second. .. Thus, in the illustration we have given, in which flow of electricity corresponds to flow of heat, the electric potential to temperature, electricity tends to flow from places of high to places of low potential, exactly as heat tends to flow from places of high to places of low. temperature He noted, however, that this analogy is restricted: ... there is, however, one remarkable difference between the phenomena of electricity and those of heat. Suspend a conducting body within a closed conducting vessel by a silk thread, and charge the vessel with electricity. The potential of the vessel and of all within it will be instantly raised, but however long and however powerfully the vessel be electrified, and whether the body within be allowed to come in contact with the vessel, or not, no signs of electrification will appear within the vessel, nor will the body within show any electrical effect when taken out. But if the vessel is raised to a high temperature, the body within will rise to the same temperature, but only after a considerable time, and if it is then taken out it will be found hot, and will remain so till it has continued to emit heat for some time. The difference between the phenomena consists in the fact that bodies are capable of absorbing and emitting heat, whereas they have no corresponding property with respect to electricity. According to this statement the application of the analogy would be limited to problems of steady flow that do not involve heat-capacity effects. In spite of this

Jan 1, 1945

By George A. Grandy, D. W. Fuerstenau

Simulation of nonlinear grinding systems is discussed in the context of the size-discretized batch-grinding model. A linear approximation of environment-dependent (or nonlinear) selection functions is postulated for systems which exhibit feed grinding orders less than unity. For this, a convex linear combination of zero and first-order selection function forms is used to obtain an analytical solution that can be used for simulation. An example in which marked nonlinear behavior occurs is rod-mill grinding. Accordingly, a series of grinding experiments was carried out in a batch laboratory rod mill to test these techniques; agreement between experiment and the model was found to be very good. Recently, significant progress has been made in the simulation of linear grinding systems by using a population balance mathematical model. Herbst and Fuer-stenaul presented a parameter estimation scheme that can be used with the size-discretized batch-grinding model, and Gumtz and Fuerstenau3 have extended these techniques to the simulation of locked-cycle grinding. Grandy et aL." summarized the simulation of linear systems and noted important alternate solutions to the batch-grinding equation. Kelsall et a1.'-" discussed the dynamic simulation of linear batch grinding, as well as linear open and closed-circuit grinding. In all of these, the key word is linear, which certainly restricts the engineer trying to simulate a variety of grinding systems. This paper discusses an approach for the simulation of non-linear grinding systems, particularly those which exhibit grinding orders less than unity. Experimentally, dry rod-mill grinding is used to evaluate the technique presented. Batch Grinding Model The size-discretized batch-grinding model has been discussed in detail by Mika et al.'.' and by Herbst and Fuerstenau,' and therefore, will only be briefly developed here. The model is formulated by making a differential mass balance of each size fraction in such a manner that the equation parameters are precisely defined in terms of selection and breakage functions,' which can be either calculated'.' or estimated1 from experimental data. The model is phenomenological because it averages all stress-application events in the system and, therefore, does not distinguish the manner in which individual particles are stressed.' For this average environment, the resistance of all particles in a size fraction to breakage is defined by that size-frac-tion's selection function; and when fracture occurs from an average event, the breakage product size distribution is defined again by that size-fraction's breakage function. The model is deterministic and is derived in terms of a continuous time variable and a discretized size variable,' i.e., the n mass fractions associated with the n defined size intervals (see Table 1 for nomenclature).

Jan 1, 1971

By Wm. B. Price

The work of Leon Guillet concerning the effect of nickel on the structural properties of brass is checked. The best value for the coefficient of equivalence t, that is, the amount of zinc replaced by 1 per cent. of nickel, is shown to be-1.1 per cent. The best hot- and cold-working nickel silvers, varying in nickel content between the limits of 4 and 18 per cent., are tabulated and plotted diagrammatically. Also, some data are given showing a comparison between the physical properties of a hot- and cold-working low copper-nickel silver, and a commercial cold-working nickel silver containing approximately 8 per cent. more copper. THIS investigation of low copper-nickel silvers was undertaken to check the work of Leon Guillet on special brasses and to determine, more accurately, the effect of the addition of nickel on the microstructure of the binary alloys of copper and zinc. It was hoped that the results could be successfully applied to the practical production of low copper-nickel silvers. To explain the results of his investigations on special brasses, Leon Guillet evolved his conception of "fictitious compositions." He states,1 in his general conclusions, that on the introduction of a small amount of a third metal to a copper-zinc alloy, it enters into solid solution with the normal constituents up to saturation, but by so doing it brings the ternary alloy into a state microscopically equivalent to a binary copper-zinc alloy of fictitious composition, and physically more nearly like the latter than the brass containing copper-zinc in the ratio actually present. The physical properties of the ternary alloy, when compared to the same properties of an actual brass of the fictitious composition, are modified by the natural properties of the third element. Beyond the point of saturation, a special constituent appears and the above generalization no longer holds.

Jan 2, 1924

By Arthur Fleischer

THE Kalunite process? for the production of metal-grade alumina from alumina-containing ores is applicable, considered from a general point of view, to any aluminous raw material that can be converted to potassium alum or equivalent normal alum. This result of modern technology has been the subject of a continuous study and development since 1929, on a laboratory and test-plant scale, with initial emphasis on the utilization of alunite as the raw material. The research and developmental program was carried out by the Kalunite Company and its successor, Kalunite, Inc., an affiliate of the Olin Corporation of East Alton, Illinois. The process is now approaching the time for a major test in its history with the completion of construction of a plant having a capacity of zoo tons of alumina per day in Salt Lake City for the conversion of Marysvale, Utah, alunite ores to alumina and potassium sulphate. The Salt Lake Alumina Plant is a Defense Plant Corporation project. PRODUCTION OF ALUMINUM The known existence of alunite deposits, especially in the Marysvale district, furnished the motive for the original inquiry into the utilization of this raw material for aluminum production. The deposits in this region were actively explored during World War I and utilized for the production of potassium sulphate, an essential fertilizer, of which a shortage of monumental proportions then existed. Up to the twentieth century for alunite is a mineral with an ancient history-it was used in Europe and in China as a source of potassium alum. It never had been used successfully in. this country as a source of oxide for reduction to metal. Although the known reserves of this ore, which undoubtedly will be greatly expanded with a commercial outlet for this ore, are recognized to be sufficient for only a part of the present-day needs of aluminum, it has a definite place in the aluminum industry. Academically it points the way for future raw materials. The aluminum industry has undergone a remarkable growth in the past few years as a result of defense and war requirements. Its expansion in many ways has been beyond belief and prediction, both in volume and location. This wartime status of the industry has accelerated the consumption of bauxite to such an extent, that a re-evaluation of the raw material reserves for the future peacetime industry and for eventual wartime reserves is seemingly of concern. The generally accepted picture of bauxite ore reserves in the United States, especially in raw material suitable for treatment by the Bayer process, focuses attention on other possible sources of raw material of metal-grade oxide. The perspective for the development of a suitable process may have changed in the interim

Jan 1, 1944

By R. E. Zimmerman, T. W. Guy

IN approaching the problems of sampling coal, a brief statement of certain facts that are more or less taken for granted may be helpful: 1. The coal-mine operator needs reliable data as to the physical and chemical characteristics of his coal in order to plan and control intelligently its mining, preparation, and marketing. The consumer needs such data in order to select the equipment and the coal best suited to meet his requirements, to check the quality of fuel delivered, and the efficiency of its use. Various government control agencies require such data as a basis for classifications and establishment of limits, for use in carrying out the requirements of federal, state or municipal laws. 2. All such data must be obtained by analyses, measurements, or tests made on samples, which are taken to represent the coal tested. It is now becoming generally recognized that, in accordance with statistical laws, test results from samples are not expected to represent the exact qualities of the lot or lots from which they are taken, except within statistical, or "expected" limits. Such limits are definitely specified by some present standards of the American Society for Testing Materials and the British Standards Institution. 3. Samples that give ash within satisfactory limits are usually assumed to be sufficiently accurate for other analyses, except under special conditions such as meeting close specifications for coals showing wide variability in sulphur, fusibility of ash, or other quality. 4. In modern coal sampling the increment is recognized as the basis for taking samples. For a given accuracy the number and weight of increments specified are increased with: (a) the expected ash, and (b) the top size designation of the lot to be sampled. 5. It is extremely important that every sampler recognize that: the specified number and weight of increments are minimums, and that the precautions to be used in order to take them properly are also minimums; that in the reduction of the gross sample the sizes specified for the coal after each stage of the crushing are maximum; that the quantities specified to be taken after each crushing stage are minimum; that any short cuts or failures to meet the requirements specified will reduce the statistical accuracy of the results, although it is possible that one or two checks on a few results may seem to show otherwise.

Jan 1, 1950

By H. M. Zoerb

Based on the belief that operating details are a definite contributing factor to major economies, this paper traces the development of crushing cavity design in Symons cone crushers to attain maximum liner utilization. Wear rates are analyzed and compared in this presentation and drawings illustrate succeeding design changes. IN these times of rising labor and material costs, it has become more and more necessary that attention be paid to some operating details which, in their obscurity, may he the key to major economies. Liner wear in crushing cavities of secondary and tertiary crushers can become an appreciable cost item when the material to be crushed is hard and abrasive. This item of cost not only includes the value of the crushing members, but also more intangible costs such as labor and lost production due to more frequent replacement. The variables which are encountered in ores and minerals to be reduced; the design of plant and machine application; the sizes, shape, and fineness, characteristics of the crushed product; the moisture; hardness; friability; and abrasiveness of the material to be crushed are all influencing factors which must be taken into consideration in the selection of a crusher, and particularly in the design of crushing cavity and liners to be used in a crusher. Through a research program undertaken in cooperation with many operators of Symons cone crushers a new approach to crusher cavity design was made, resulting in the development of liners for specific operations which showed: 1—maximum utilization, as high as 70 to 80 pct of original weight of metal, and 2— maximum capacity of unit during the greater portion of its life. It has been found that liners so designed for a given operation will show added economies in power consumption, maintenance, and general wear and tear on the crushing unit. Initial work in the so-called tailoring of crushing cavitles was begun on the tertiary or fine crushing units where as a rule reduction ratios were low, varying from 3 to 6. Parallel or sizing zones in the lower portion of the crushing cavity were too long, resulting in a tendency to pack. It was found that very little additional crushing was done in the parallel zone after the initial impact in that zone and that a relatively small amount of' additional crushing was done by attrition, which required very careful feed control. A small amount of over-feeding would result in packing which not only consumed power but caused unnecessary liner wear as well. The illustrations which follow in this discussion will show only contours of crushing cavities, and for purposes of simplification the cavities will be considered only in their closed position. The first step, therefore. was to reduce the sizing zone to a minimum. This was done by removing the lower portion of the liner as shown in Fig. 1. The result of the change was a saving of 15 to 20 pct in liner cost, less power consumption, with no change in capacity. This change in design, while an improvement, did not go far enough. As wear took place, the change in the liner was not uniform throughout its entire length, resulting in a restriction of the feed opening and thereby loss of capacity. Furthermore, progressive wear of the liner had the effect of lengthening the parallel zone until finally the entire crushing cavity was all parallel zone, see Fig. 2. It is obvious from the reduced feed opening of the worn liner that the ability of the machine to receive material is lessened considerably. Furthermore, the long parallel zone with its worn, irregular profile did not operate at its highest efficiency. The first attempt to overcome this difficulty was carried out on a 5 1/2-ft crusher installed in a plant producing roofing granules. The material being crushed was a very hard graywacke and the crusher was closed-circuited with a screen having .232-in. slotted openings. A radical change in contour was developed, as illustrated in Fig. 3. Equal wear lines on both concave and mantle are designated 1, 2, 3, etc. The method of development of this contour is as follows: Since adjustment for wear is vertical, corresponding intersections of wear lines and vertical lines developed concave and mantle contours which maintained equal but lengthening wear surfaces in the parallel zone. The ideal contour, of course, is one in which the length of the parallel zone remains constant, but because of present foundry practice and heat treating characteristics this is impossible.

Jan 1, 1954

By J. M. Callow

THe results obtained by pneumatic flotation throughout the country on all classes of ore, and the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practicc. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cyeloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by Dr. Rudolf Gahl on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. CoMPABATIVE SENSITIVENESS AND ATTENDANCE Concerning the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that, with the exception of about 24 days at the end of the testing period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the concIusions drawn on page 499 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 1, 1917

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

By Robert Glass Cleland

FROM the time of its organization down to 1917, a period of more than eighty years, Phelps, Dodge & Co. was seldom involved in what could be called a major labor difficulty. Behind this remarkable record lay both a philosophy and its practical application. The philosophy was an attitude toward society called the Golden Rule. That philosophy had been a living principle in the lives of the founders of the company, Anson Phelps, Daniel James, and William E. Dodge. Their successors, William E. Dodge, Jr., and Daniel Willis James, accepted the same philosophy. Dr. James Douglas governed his life by it. All of these men and their families had given tangible expression to that conviction in benefactions of great magnitude and variety-churches, hospitals, educational institutions, libraries, missionary undertakings, and other organizations for human betterment, such as the Young Men's and Young Women's Christian Associations, and the development of model communities about their mills and factories. According to the best standards of their generation, they had sought to improve the condition of labor,

Jan 1, 1952

By J. L. Craig, C. L. Edwards, M. D. Harper, J. M. Ray

The Los Alamos National Laboratory executed 19 intermediate scale cratering experiments in oil shale at the Colony Mine in Garfield County, Colorado. These experiments have led to a better under- standing of fracture characteristics and fragmentation of & - oil shale by use of a conventional high explosive. Geologic site characterization included detailed mapping, coring, and sample analyses. Site-specific geology was observed to be a major influence on the resulting crater geometry. The joint patterns at the experimental site frequently defined the final crater symmetry. Secondary influences included vugs, lithology changes, and grade fluctuations in the local stratigraphy. Most experiments, in both the rib and floor, were conducted to obtain data to investigate the fragmentation results within the craters. The rubble was screened for fragment- size distributions. Geologic features in proximity to the explosive charge had minimal effect on the rubble due to the overpowering effect of the detonation. However, these same features became more influential on the fracture and rubble characteristics with greater distances from the shothole. Postshot cores revealed a direct relationship between the grade of the oil shale and its susceptibility to fracturing. The Colony Mine experiments have demonstrated the significant role of geology in high explosive/oil shale interaction. It is probable that this role will have to be considered for larger applications to blast patterns and potential problems in retort stability in the future of oil shale development.

Jan 1, 1983

By S. F. Shaw

IN 1913, the Tiro General mine, at Charcas, S.L.P., Mexico, which had been making from 125 to 150 gal. of water per min., was allowed to become flooded, after all the pumps had been removed, and in 1918 the problem of unwatering it came up for solution. There are two vertical shafts, the Tiro General, 1390 ft., and the San Fernando, 1225 ft. in depth, with five connecting levels between them. The San Fernando shaft had been partly retimbered, while the Tiro General had been newly timbered from the collar to, 1090 ft. in depth. It had been possible to place guides in only one compartment of the Tiro General, from the collar to the seventh or 850-ft. level, to which it was necessary to lower the water before station pumps could be installed. Soundings indicated that compartments in the Tiro General were open to 1082 and 428 ft., and in the San Fernando shaft to 471, 488, and 586 ft. The water had risen to a point 140 ft. below the collar of the Tiro General shaft. PUMPING EQUIPMENT The steam plant at the Tiro General shaft includes one 300-hp., one 150-hp. and one 100-hp. Erie City water-tube boiler, and two 160-hp. Heine water-tube boilers. All but one of these boilers were supposed to be in good shape, but it was soon discovered that six years of idleness in a climate that is foggy for several months of the year had left them in poor condition. The compressed-air plant comprises one Nordberg cross-compound compressor with piston displacement of approximately 2500 cu. ft. of free air compressed to 96 lb. per sq. in.; and another Nordberg cross-compound with piston displacement of 1235 cu. ft. of free air, to the same pressure.

Jan 2, 1920