Search Documents

By Breno T. Maia, Débora C. O. Silveira, Mariana A. Ribeiro, Daniel A. G. de Carvalho, Roberto P. Tavares, Raissa S. Salgado

Mixing time is an important parameter when considering chemical and thermal homogenization in steelmaking reactors. It can also be relevant in the kinetics of chemical reactions. Different methods have been used to estimate mixing times in physical models of steelmaking reactors. In the present work a new method to estimate mixing times in physical models has been proposed. This method can be used when transparent fluids are used to simulate the liquid steel and the slag. Results of mixing times in a physical model of a BOF obtained with different techniques were compared. It was shown that the new method is more reliable and consistent than the common methods based on electrical conductivity measurements and colorimetric analysis.

Oct 1, 2019

By Jorge Madias

Neste trabalho se leva a cabo uma revisão da literatura sobre defeitos em beam blanks. O foco é no mecanismo de formação e as soluções propostas para diminuir sua ocorrência. Os defeitos superficiais incluidos são as trincas longitudinais e transversais, bleeding, pinholes e escória. Os defeitos internos levados em conta são os blowholes, as trincas centrais e as trincas nas pontas das abas. A revisão incluie as técnicas utilizadas para pesquisar os defeitos: caracterização metalográfica, CFD, modelagem termodinâmica e termomecânica, etc. As medidas adotadas estãorelacionadas a mudanças no sistema de lingotamento (por exemplo o design da vâlvula submersa), design do molde, mudanças e regulação do resfriamento secundário, suporte dos veios.

Oct 30, 2017

By Anna Carolina Cerqueira Neves

Synthetic fiber has been gradually replaced by natural fiber, such as lignocellulosic fiber. In comparison with synthetic fiber, natural fiber has shown economic and environmental advantages. The natural fiber presents interfacial characteristics with polymeric matrices that favor a high impact energy absorption by the composite structure. However, until now little has been evaluated about the hemp fiber incorporated in polymeric matrices. This study has the purpose of evaluate the impact resistance of this kind of epoxy matrix composite reinforced with different percentages of hemp fibers. The impact resistance has substantially increased the relative amount of hemp fiber incorporated as reinforcement in the composite. This performance was associated with the difficulty of rupture imposed by the fibers resulting from the interaction of hemp fiber / epoxy matrix that helps absorb the impact energy.

Aug 16, 2017

By Carolina Sartori Marzullo

Apresenta-se a metodologia e sistemática para gestão da capacitação como ferramenta para aumento da competitividade e ganho de resultados do negócio num contexto crítico para o segmento.

Aug 16, 2017

By Flanelson Maciel Monteiro, Marcondes Mendes de Souza, Mauro Froes Meyer

This research is based on a bibliographical review of a field work that was done in the municipality of Parelhas / RN. The area explored, in turn, is known for its richness of mineral resources that are present in pegmatitic rocks. The general objective of this research is to characterize the main properties of the pegmatites and quartzite, in order to verify the heterogeneity of the elements, to raise a possible viability of extraction for economic purposes. The quartzite also presents a siliceous chemical composition. This rock is a source of bricks and silica refractories used in the steel industry and for the preparation of the blast furnace bed, ornamental rock used in different ways (rustic, carved, polished, among others). However, this research resulted in preliminary data, but it would be interesting to be more detailed in order to evaluate the economic viability of these rocks.

Oct 3, 2019

By Karl Berger, Michael Steinkogler

The evolution in Metal Cutting: Inventors around the world have been successfully developing innovations for decades, but only some of these developments have had „GAME CHANGING“ potential. One of these innovations is the new developed saw blade LINCUT®, a patented changing system that paves the way for a fundamental reorientation of the entire saw blade industry worldwide through a simple and economical concept for rolling mills or heavy forging lines. Cost efficiency starts with the raw material: Circular saws equipped with a standard saw blade are expected to have a necessary 2 percent standstill per year due to required tool changing. The applied technology reduces this unnecessary loss of production by more than 50%. The ROI can therefore be reached faster which immediately lowers your production costs. No matter what material, conventional carbon steel or highly alloyed stainless steel, the coating and shape of carbide plates is perfected for extended tool life up to 25% with increased performance. Due to LINSINGERs own tool-technology-centre in Austria specialized in research and development of tools, constantly expanding R&D activities, best results are achieved in quality and cost efficiency: a (r)evolution in metal cutting.

Oct 1, 2019

By Jean Viana Bahia, Antônio Adel dos Santos, Vicente Tadeu Lopes Buono

During cold rolling of Cr-Mo alloyed DP steel, considerable oscillation of thickness may occur. The literature points out that such occurrence is due to non-uniform cooling of the coil after the hot rolling process. Since the austenite transformation in this steel continues after coiling, the microstructure and, consequently, mechanical properties are very susceptible to natural variations in cooling rates associated with distinct positions of the coil. The influence of coil cooling conditions on thickness oscillation during cold rolling was evaluated in this work by using both industrial experiments and dilatometer tests. It was verified that an industrial coil presented large variation of mechanical properties associated with its heterogeneous microstructure. Consequently, thickness oscillation occurred during cold rolling. Dilatometer tests simulating hot run-out table and coil cooling showed that the austenite transformation is very slow under small cooling rates that occur after coiling. Thus, the slow transformation rate makes the coil very susceptible to environmental conditions around it during its natural cooling and is responsible for variation in mechanical properties of the coil. To ensure the formation of a more homogeneous microstructure in the whole coil, it is necessary either to make use of technologies that improves the cooling uniformity or to adjust the steel alloy design. The latter alternative has been done with relative success by using conceptions with lower amounts of Cr and Mo.

Oct 1, 2019

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

This article is based on a bibliographical review of a field work that was done in the Salina São Camilo in the region of Mossoró - RN. The general objective of this research is to present the main exploratory and beneficiation aspects of salt production. Among the aspects of salt is the properties of salt, history and mining, besides the aspects of environment and work safety. However, this research resulted in preliminary data, but it would be interesting to be more thorough so that the extraction of salt in the academic world is disclosed

Oct 3, 2019

By Lorenzo Bacchetti

Automatic yards with ad-hoc WMS (Warehouse management software), are the key for a modern and efficient warehousing which can face today logistic challenges. WMS boosts the traceability of material while optimizing the storage space. The operations in the yard are safer and logically organized according to algorithms that are specifically adjusted case by case. WMS can easily handle multi-cranes yard avoiding conflicts and increasing accuracy of positioning with decreased number of movements. The synergy of automatic cranes and WMS reduces bottlenecks and speeds up the preparation of deliveries with an overall improvement of warehousing and shipping scheduling.

Oct 1, 2019

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By Angelo dos Reis Magalhães

Brazilian companies have adopted in recent years new management practices to remain competitive. Specialized consulting in asset management progressively creates or adapts new techniques in order to increase availability and reduce manufacturing costs, maximizing profits. New engineering concepts were acquired and implemented by executives in all business segments. Techniques, such as FMEA, RCM, LCC, Pas 55, Reliability studies by Monte Carlo simulations, among others, have become increasingly recognized as important tools to enhance managerial performance. Besides these techniques, this study suggests the importance of adequate structuring of a lubrication program, as a critical success factor for the reliability of any asset. Through a case study developed with a company in the mining sector, this work proposes the development of a master plan for lubrication based on three pillars: People, Equipment and Management system. Practices and care with lubricants, hydraulic fluids and coolant, until its point of application, shall be evaluated to ensure a correct contamination control and a high level of assets availability. This discussion sheds light onto other benefits of this process, including occupational health and safety; ergonomics; environment and sustainability.

Jul 31, 2018

By Eric Yoshimitsu Sako

One of the main difficulties in the operation of trough and runners at Arcelor Mittal Tubarão (AMT) Blast-furnace no.02 is the reduced amount of time available for repair procedures. The consequence is that the castable installation must often be performed during hot conditions and the installed castable could easily detach from the base material during the early stage of operation, exposing the previously oxidized base material to molten iron and corrosive slag attack. When events like this happen, emergency repairs must be executed, resulting in increased refractory unit consumption and an unplanned shutdown of unit operation. Considering these targets, Nippon Crucible Co. and Saint-Gobain HPR Brazil have developed a high-performance Al2O3-SiC-C composition based on an entirely novel anti-oxidation technology. Oxidizing reactions could be attenuated by adding an oxidant inhibitor and a water reducing agent. As a result, the open porosity was significantly reduced, resulting in an improvement of campaign life in terms of pig iron throughput when compared with the regular castable. An analysis of this life improvement showed successful results for the material after 250 days of campaign. The main reason for such successful results was that the deterioration caused by the oxidation was significantly less and that this change made on the high cohesive structure of the base material was maintained for a long time. The attained results allowed Arcelor Mittal Tubarão to achieve longer trough campaigns, and avoid any unplanned stoppages with zero breakdown risks.

Oct 30, 2017

By Lara de Assis Moreira, Vinicius Thiago Lecco Rampinelli

The energy efficiency of reheating furnaces is a continuous challenge, as these equipment consume a representative portion of the total fuel of an integrated steel plant. Therefore, any investigation and implementation which brings improvement in this figure become an important issue for the mill competitiveness. In the case of production delays due to external factors (the condition addressed in this work), whether predicted or unforeseen, the slabs remain inside the furnace with high temperatures in order to avoid production delay during the production restart, elevating the specific consumption and scale formation. This work increased the energy efficiency of the two ArcelorMittal Tubarão’s walking beam reheating furnaces, by reducing the consumption of mixed gas during production delays (either scheduled or not) lasting less than 3 hours. The objectives were achieved through improvements, among them, tuning of Level 2 automation system parameters, automatization of procedures and operational training. The work resulted in a 34.4% fuel gas consumption reduction during the delays.

Oct 1, 2019

By Delio Amorim

Industry 4.0 concepts is the new biggest challenge on the industry nowadays and every company in every industry in every part of the globe is looking to implement this somehow on their factories and machines. To do that on the newest long rolling mills, that brings already onboard state-of-the-art technologies, is for sure a challenge of machinery builder industry, but how to become the long rolling mills built on 70’s, 80’s or 90’s part of this innovation process and connected to the new trends? This is the main mission here, to show some examples of applications that goes in this direction.

Oct 1, 2019

By Rainer W. Kaiser

High wear resistant HSS rolls are being successfully used in the first stands of HSM finishing trains since the early 1990´s. The strong demand of mill administrators to make them applicable also in the last stands of the finishing rolling mill is a major influence factor of R&D efforts at respective roll suppliers. Looking back to the successful replacement of ICDP and HiCr rolls by more economic HSS rolls in F1-4 in regard to the TCO, rolling mill managers wish to repeat such scale gain also at F5-7 stands. Actually used enhanced ICDP rolls wear faster, being the HSM stoppage factor. F1-4 HSS rolls can be used for example 3 times longer. There is an obstacle to be overcome by roll suppliers and end users to replace F5-7 rolls by HSS rolls. Stick and crack resistance properties of HSS need to be improved. As a worldwide known leading producer of cast rolls for steel mills since 1820, the traditional German family owned foundry and machine shop IRLE, existing since 1693, accepted to face also this additional challenge. IRLE´s long year experience and prior researches have shown possible development directions to improve mentioned stick and crack resistance properties of its HSS grade, called SST. A new material of the HSS family is in the development pipe line and is discussed: SST/G. Choice criteria of the development direction, steps to control and guarantee respective sections of an industrial scale production as well as observations and results are described.

Jul 30, 2018

By Christoph Aichinger

A smart combination – Primetals Technologies developed the Circular Pelletizing Technology (CPT), which is a combination of the well-proven travelling-grate pelletizing technology with the design of a circular dip rail cooler of modern sinter plants. The overall space requirement and the installed weight for a CPT plant is significantly less compared to conventional technologies and by that CPT is a very attractive alternative for new projects.

Aug 16, 2017

By Karl Berger

The paper gives a comprehensive overview of the historical development of various metal rolling technologies and also describes the influence to industrial and socio-economic developments. The rolling of steel, in particular of rails, beams, rebar, strip and plate has enabled the large scale transport and travel, the building of bridges and buildings, the manufacturing of ships and cars. All this has changed the face of the world significantly. Further the paper approaches technological highlights in the design, manufacturing, drive and control of modern mills and the various types developed to create industrial economic units for the different markets and customers’ requirements. An outlook of future challenges is as well discussed in the paper. Various solution approaches for the rolling technologies, from continuous improvement of existing plants to more radical new concepts like endless rolling, near net-shape casting and rolling are approached. A positive conclusion is drawn that rolling technologies will remain a valuable area for engineers with scientific and economic challenges, but also a clear vision for positive contribution to further industrial and social development.

Jul 30, 2018

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By Felipe das Dores Machado

O estudo de simulação do escoamento do aço líquido no distribuidor requer não somente um grande conhecimento técnico dos critérios de similaridade, mas também uma correta aplicação das ferramentas disponíveis de simulação dos fenômenos físicos envolvidos. A complexidade do escoamento, tendo em vista a interação das inúmeras variáveis envolvidas, torna necessário um estudo dinâmico que utilize diferentes métodos que abranjam a visão de um todo do escoamento, aumentando as oportunidades de uma conclusão mais assertiva sobre os fenômenos ocorridos nas reais condições encontradas na indústria. Este trabalho tem o objetivo apresentar uma nova abordagem sobre a simulação da remoção de inclusões do escoamento do aço líquido em modelos físicos do distribuidor de lingotamento contínuo e como resultado será mostrado um estudo de caso comprovando que a utilização de um único método de modelagem física pode levar a compreensões equivocadas do escoamento.

Aug 16, 2017

By Fernando Generoso Neiva Ferreira

Os aços alto carbono baixa liga são amplamente utilizados, principalmente em componentes que necessitam de elevada resistência mecânica, manutenção de forma e resistência à abrasão. São largamente aplicados em lâminas de corte, molas, peças de segurança, implementos agrícolas, utensílios, serras em geral, entre outros. Neste trabalho, estudam-se, em escala industrial, os parâmetros de processo, as características críticas para o desenvolvimento e as propriedades mecânicas e metalúrgicas de um aço alto carbono baixa liga especialmente desenhado para a produção de correntes de motosserra. Utilizando ensaios de tração, dureza, microscopia óptica (MO) e eletrônica de varredura (MEV), avalia-se a evolução das características mecânicas e metalúrgicas do aço estudado.

Oct 30, 2017