Search Documents

By Giuseppe Pintaude

This study aims to evaluate the effect of specimen preparation on the dry sliding wear behavior of CA-6 NM stainless steel. Two different surface finishing manufacturing processes were applied: lapping and metallographic polishing. The wear tests were conducted in reciprocating ball-on-flat system, performed for two loads: 5 or 8 N. For all test conditions, hardmetal ball was employed as counterbody. The surfaces were evaluated using 3D interferometry technique to determine their surface roughness, including texture analysis regarding isotropy. Surface characterization results indicated the presence of texturing and preferential orientation, since the parameter Str was smaller than 0.5 for samples of both the studied conditions. Two distinct levels of isotropy evaluated through Str parameter were achieved: 0.13 for lapping and 0.3 for metallographic polishing process. It is clear from wear tests that the variation of average surface roughness is the key point for tribological behavior of CA-6 NM stainless steel.

Jul 31, 2018

By Leonardo Camilo dos Reis, Edmilson Fernandes Dadomi, Claudio Silva de Paulo

In the hot strip mill production, one of the factors that may affect the productivity is the occurrence of failure due to the geometry of the strip at the exit of the rolling mill, because the tip of the strip can turn-down or turn-up. This study had the objective of evaluating the behavior of the strip when leaving the working rolls, through numerical simulation, aiming to know the influences of the main variables that govern the formation of the turn-down. The methodology consisted in performing the computational simulation of the strip mill and to vary the operational and geometric parameters that could influence the process. The results showed that the rolling of hot strips of HSLA material with final thickness varying between of 3 to 6 mm and a reduction of 6.6% to 11.0% in the last stand of a hot strip mill, tends to bend towards the roll with larger diameter, higher friction coefficient , higher temperature and lower limit of material flow. It was observed that the variation in diameter is the main factor that contributes to the formation of the curvature of the front-end of strip. Based on these results, several measures were implemented in the industrial line, with a significant reduction in the occurrence of turn-down.

Oct 2, 2019

By Carolina Gomes Dias Ribeiro

The modern composite materials, especially those reinforced with synthetic fibers such as glass and carbon, have been used since last century to attend the demands required by most technological fields, from home appliances to aerospace. Natural fibers composites with biodegradable polymer matrices are considered environmentally friendly materials and currently accepted as possible substitutes for synthetic composites. These green composites can be safely discarded or composted at the end of their life without harm to the environment. Another alternative for synthetic composites is to apply natural lignocellulosic fibers as reinforcement of conventional polymer matrices and already used in the automobile industry. In addition to the environmental and societal advantages of the green composites, the lignocellulosic fiber reinforced conventional polymer composite also has economical and technical advantages. In the case of a fiber collected as a waste, the price of the composite can be considerably lower than “fiberglass”. Furthermore, with high strength lignocellulosic fibers such as sisal, ramie and malva the specific strength of a composite may approach that of “fiberglass”. Therefore the objective of the present work is to investigate the mechanical behavior of polymer matrix composites reinforced with high volumes of natural malva fibers subjected to tensile stresses.

Aug 16, 2017

By Nestor Cezar Heck

Aim of the present work is to continue the theoretical evaluation of the slags of the fundamental system CaO-SiO2-CrOx-MgO (Ca-O-Cr-Si-Mg quinary system) at the temperature of 1,873 [K], with the help of a computational thermodynamic tool. Driving force for this and the previous research works is the understanding of chromium losses from the molten bath into the slag. Especially motivating is the presence of solid phases in the slag, since they may prevent refractory degradation and help in the production of foaming slags. Nevertheless, Cr-bearing solid phases can lead to Cr losses, being therefore detrimental. Determination of the states of thermodynamic equilibrium for this system using a slag with fixed composition as a start material were made using MgO amount as variable. Results show the impact of the MgO content on the equilibrium phases (molten metal, liquid slag, solids) and their composition for this system.

Jul 30, 2018

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Sander Mul, Michael Brandner, Armin Paar

Graphitic HSS roll grades such as ESW’s brand VANIMO can be considered as the latest developments for the last finishing stands in hot strip mills. These roll grades are developed on the basis of the alloying concept of (Carbide Enhanced) Indefinite Chill work roll materials. During the development of VANIMO, the amounts and types of carbide forming elements were increased and adjusted into the direction of cast HSS roll grades. The microstructure of graphitic HSS roll grades therefore consists of tempered martensite, cementite and several different carbide types as well as a well-defined amount of free graphite. The main purpose of graphitic HSS roll grades is to combine the high surface quality of Indefinite Chill alloys as well as the high wear resistance of HSS roll grades. Several systematic steps were taken to increase the wear performance from Carbide-Enhanced Indefinite Chill grades to the more advanced VANIC grade and further on to the highest alloyed roll grade VANIMO. In every development step, the surface quality of the roll grades was carefully monitored. The decision to invest in new testing equipment at ESW’s plant was driven by the wish to see microstructural effects of different alloys in a macroscopic dimension. Usually samples are taken from cast rolls and investigation is done in comparably small areas compared to the total surface of a roll. Rolling of strip is done with the entire barrel, so effects of alloy and microstructure can appear anywhere on the barrel surface. To ensure better understanding and deeper knowledge about influences of alloying trials we decided to install the last version of LRI (Lismar Roll Inspection). LRI includes the latest technology of Eddy Current with an enormous resolution. Depending on the formation of carbide precipitations, carbide network as well as matrix and free graphite, the EC test can detect smallest differences. The possibility to analyze the different results of EC and UT surface wave inspection will be discussed. A few examples of surface effects in the mill application will be discussed and improvement strategies explained.

Oct 1, 2019

By Márcia Maria da Silva Monteiro Pereira

Durante o lingotamento contínuo de aço, partículas de ZrO2 adicionadas na escória de molde facilitam a nucleação heterogênea de cristais devido à sua limitada solubilidade. A adição de ZrO2 promove a cristalização da fase cuspidina, o que auxilia na redução da transferência horizontal de calor no molde, amenizando desta forma o problema das trincas longitudinais. Outro benefício da adição de ZrO2 em pós fluxantes é reduzir a taxa de desgaste da válvula submersa (SEN) na interface metal/escória; a erosão da SEN é um problema sério. Através de testes de laboratório e de testes industriais concluiu-se que a adição de ZrO2 em pós fluxantes reduz a taxa de transferência de calor horizontal no molde durante o lingotamento contínuo de aço, considerando os dois tipos de pós fluxantes que foram analisados no presente trabalho. Além disso, observou-se que a adição de ZrO2 reduz a taxa de desgaste da válvula submersa na interface metal/escória.

Aug 16, 2017

By Ivo Filipovic

The steel melting process in an Electric Arc Furnace is a complex set of tasks, coping with highly dangerous hazards as fire, explosions, uncontrolled reactions, hot metal projections and gas or dust emissions. Melt shops are dangerous working areas for operators, recording statistics with a high frequency of injuries. In the past years, without dedicated safety equipment, there wasn't a real attitude to the risk prevention. The paper describes the available technological packages to eliminate the manned activities on the melting floor, with the aim to prevent accidents and keep furnace operators safe. The technological packages suite extends the automatic control of the EAF melting process to all the operations from charging phase to tapping. Plus, the integration of the most frequent operations by automated specialized tools effectively minimizes power-off times, enhancing reliability and improving the transformation costs.

Aug 17, 2017

By Mario González Ramírez

The safe transport of sour gas requires steels with enhanced hydrogen induced cracking (HIC) resistance. Centerline segregation bands of high hardness microconstituents and non-metallic inclusions are the heterogeneities usually linked to HIC failures in pipeline steels. Full-scale production heats of a new low Mn, Nb microalloyed steel were produced by different steel mills aiming at the application in sour gas environments. The new alloy design provides both effective strengthening and control of sulphide inclusions. Coil microstructure consisted of fine grained ferrite with a small volume fraction of uniformly dispersed eutectoid aggregates. Most importantly the microstructure was uniform in both the longitudinal and transverse directions and exhibited exceptional consistency. Samples from this steel were submitted to HIC testing according to NACE standards TM0284-2003 without any sign of cracking. The results, so far, confirm that this new alloy design provides the unique opportunity to economically produce a high strength pipe steel grade with improved sour service resistance for the linepipe industry.

Aug 8, 2018

By Kermit Reins

The most recent modernization phase of the wire rod mill at Sterling Steel involved installation of a pre-finishing mill, using a Morgan Vee Mini-Block, a new water box and shear with utility systems and automation. The new mill configuration adds more stands to the mill for better drafting and is designed to improve finished product quality by providing a more uniform entry temperature, better control of the feed section into the No-Twist® mill as well as enhanced surface quality. The new shear improves cut length accuracy as well as decreases the amount of trimming to reduce yield loss. This paper explains the changes made in the mill and the features of the new equipment and automation.

Aug 17, 2017

By Keli Vanessa Salvador Damin

O tratamento de austenitização é de fundamental importância para a qualidade do aço Hadfield, já que é o tratamento que garantirá a total austenitização do material. Dentre as variáveis que devem ser controladas estão à temperatura de tratamento e velocidade de resfriamento. O presente trabalho aborda um estudo de caso sobre o controle da temperatura dentro do forno de tratamento térmico bem como o comportamento da temperatura da água na piscina durante o resfriamento do material.

Aug 16, 2017

By Giuseppe Pintaude

The use of two-dimensional shape parameters to characterize abrasive particles is a possible approach to express their angularity. Nonetheless, in sliding abrasion, especially in pin abrasion testing, coated papers structure plays an important role and even its damage during the wear process should not be neglected. This manuscript discuss the limitations of two-dimensional shape descriptors in distinguishing wear caused by relatively hard particles, indicating that the wear data obtained in sliding abrasion tests are unable to distinguish different types of coated papers used when only the two-dimensional particle projection is considered for shape characterization.

Jul 31, 2018

By Klaydison Silva, Maurício Curi Segato, Elves Matiolo, Neymayer Pereira Lima

Flotation is the main concentration process, has been applied with sucess for the removal of quartz on the iron ore industry aiming high quality concentrates. limiting the top size close to 0,300mm and the removal of slimes are fundamental for the efficiency of reverse flotation of quartz. The high consumption of reagents, leading to insufficient particle coverage, and increased foam stability, leading to the difficulty of removal of quartz particles, are the main deleterious effects of the presence of slimes. Recent characterization studies, together with the development of new collector of linear chain, allowed the obtaining of concentrate with SiO2 contents close to 3% with 94% of metallurgical recovery, based on pilot tests carried out on a sample flotation column of the Quadrilátero Ferrífero.

Oct 3, 2019

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017

By Andrea Taurino

Innovation means implementing a new product or a product that has undergone significant improvement over time, in terms of method, form and performance. Innovation encompasses all the scientific, technological, organizational, financial and commercial steps that need to be taken to put it into operation. Innovation combined with research and development makes it possible to perfect the product with consistency over time. Taking inspiration from the bases developed by the Austrian economist Joseph A. Schumpeter back in 1911, Danieli came up with the concept of “Innovaction” – a combination of Innovation and Action, to refer to the development and advancement of various products for the steelmaking industry, including the loop laying head for wire rod.

Aug 17, 2017

By Gergö Rimaszéki

Due the fast growing of pig iron and steel in the last years associate with some mineral resources changes (Hematite?Itabirite), has been checking the sinter feed degradation. The typical sinter feed (0.15;-6.3 mm) has become limited and the rapid growing production resulted in more and more fine ore (< 150 µm) availability in the market. The sinter plant operators are facing several new challenges since the mixing and granulation- and the sintering behavior of the fines containing mixtures often differs from the traditional sinter feed´s behavior. The utilization of fines in the sinter plants might increase the process water consumption required for the mixing and granulation process or even the solid fuel consumption, which effects the operational cost of the plant significantly. The current study presents an overview about Outotec´s laboratory facilities and competence regarding the mixing and granulation of fines in different equipments. The usage of high intensity mixers (HIM) – vertical and horizontal as well – showed to be the most effective, based in cold agglomeration tests in small scale, in case of fine ore handling. Permeability and particle size distribution curves are used to evaluate and demonstrate the efficiency of the different equipments. Outotec´s ”Know-How” with the different type of mixer and the modern laboratory facilities provide an excellent opportunities to optimize the mixing and granulation procedure and utilize up to 100 % pellet feed

Aug 17, 2017

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Matheus Sampaio Modesto de Paula

O presente trabalho mostra o desenvolvimento de um produto, até então não comercializado pela CSN/PR, criado para o aproveitamento da capacidade ociosa de seu laminador reversível a frio. Historicamente, a produção do laminador era direcionada exclusivamente para o abastecimento de uma linha de galvanização contínua, mas trabalhos bem sucedidos para o aumento da produtividade do laminador resultaram em capacidade excedente do equipamento. Diante desse cenário, a comercialização de bobinas Full Hard se tornou uma opção viável para a abertura de mercado e aumento de competitividade, frente a atual pressão imposta por produtos importados. Visitas aos potenciais clientes foram necessárias para o levantamento das características importantes a seus processos produtivos e adequação dos parâmetros utilizados no laminador reversível. Atualmente o produto está homologado e sendo fornecido a clientes externos, e espera-se o aumento da carteira, dependendo apenas da evolução do mercado.

Jul 30, 2018

By Douglas Glenn Stalheim

The demands for improved mechanical properties in hot rolled long products are increasing as the expectations of global Standards and construction designer’s increase. Cost constraints limit the excessive use of expensive alloys to meet these expectations. In addition, depending on the mill, equipment can limit what can be realized to meet the increasing expectations. The most effective way to meet the increasing expectations for improved mechanical properties of optimum strength and ductility is through producing steel with as fine as possible uniform cross sectional grain size in the “as-rolled” condition. The best solution to the development of this fine and uniform cross sectional grain size is to develop a cost effective alloy design coupled with proper metallurgical process control implemented into an existing mill’s equipment capability and layout. In other words, properly bringing together alloy, metallurgy, process control and existing equipment capabilities to develop an optimum product that can meet the increasing demands of the construction designer. This paper is designed to give a solid understanding of the production and metallurgical requirements to achieve a grain size in “as-rolled” long products that is as fine as possible within the limitations of the process and production parameters of the individual plant.

Jul 30, 2018

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018