Search Documents

By Jacob W. Young

A casual reading of the geological literature extant to-day would give one the impression that carbon is an element which by some chance or another always existed at or near the surface of the earth, and was never of a magmatic origin. The carbonaceous matter in shales is said to be of vegetal derivation; petroleum is stated to have been derived from vegetable matter or from marine animal bodies; if carbon or bituminous matter is found in igneous rocks or associated with metallic ores, the statement is made that deeply buried carbonaceous sedimentaries were undoubtedly the source from which such carbon or bituminous matter was derived. This, I do not consider a reasonable or common sense view of the matter. Carbon is one of the elements of which the earth is composed. In the table giving the periodicity of the elements it comes sixth in the order of increasing atomic weights. It is an element formed like all the rest were formed, and must be as common to the interior of the earth as the rest of the eighty-odd elements so far discovered. The spectroscopic analysis of light from the sun, and the stars, shows the presence of carbon in the sun and in the colder stars. Thus with carbon, an element, found throughout the universe as well as on the earth, it is entirely reasonable to consider it as present in the interior of the earth with the other elements. Such being the case, the magmatic origin for the various forms of carbon in rocks and ores is a rational and logical conclusion. If but a small fraction of thought and effort was made along these lines, which is made in fostering the idea of the organic origin of the carbon found in the earth's crust, untold advances in this phase of geological science would result.

Jan 1, 1925

The U.S. Bureau of Mines has been concerned for many years with the general problems of underground coal mining and the particular problems due to the methane content of the coal. The Bureau and others have worked diligently to improve the health and safety conditions for underground coal miners. It has been recognized for many years that the methane in coal would have some value if it could he recovered and used, Also its removal before coal mining began or during the mining cycle itself would make mining safer and more economic due to a potential saving in ventilation costs. The work covered in this report was carried out to review methods of removing methane from active and inactive regions of operating coal mines and to determine how the methane could be concentrated and utilized economically.

Jan 1, 1975

By J. E. Cleveland

The major health concern for uranium miners is the release of radon gas and the resultant ingrowth of the short lived daughters in the mine atmosphere. Present methods of control are the utilization of mine ventilation systems for dilution and control of ingrowth time to maintain working levels below those set by regulations. This study examined pressure cycling efforts on the radon emanation. The mechanical ventilation systems were altered to allow pressure changes throughout the mine to increase radon influx during the off shifts and thus deplete the sources of radon gas. Continuous radon working level and environmental monitors, developed by the Bureau of Mines, were employed to monitor radiation and physical parameters in the mine workings. The mine ventilation system was then varied to induce radon flows during off shifts, thus, depleting the radon sources during normal production shifts. Electro-static precipitators were also tested to determine radon daughter collection efficiencies. Both radon and radon daughter concentrations were monitored and evaluated. Major problems were found in the simple mechanical operation of cleaning these units.

Jan 1, 1982

By G. W. Marks, A. H. Roberson

"Previous investigation 4/ has demonstrated that some of the aliphatic amines are suitable absorbents for 302, This paper reports the results of physical studies of a number of such amines with the object of determining which is most favorable as an absorbent.Monoethanol amine, diethylene triamine, and triethylene tetramine appear to be the most promising of all the amines studied, and most of this report has been devoted to studies of the physical properties of their aqueous solutions, which contain varying amounts of SO2.PURITY OF MATERIALSAll of the amines used were of commercial grade, because the primary object of this research was the investigation of a proposed works process rather than the accumulation of scientific data.The aminoethyl derivitives of ethylene diamine, namely, diethylene triamine, triethylene tetramine, and tetraethylene pentamine, only recently have been produced commercially. The chemistry of aliphatic amines is complex, and these newer derivitives have not been investigated, completely. Chemically pure material is not on the market, and since definite physical standards have not been published, one could not be assured of a pure product even if the commercial material was refined.The compilation of physical constants for the pure amines would involve much time—consuming effort without materially enhancing the value of this paper, as this work was not devoted to the development of fundamental standards."

Oct 1, 1938

By D. H. Trollope

In engineering in general, close agreement between theoretical predictions and structural performance is rare—this is particularly true in rock slopes. Since the complexity of natural arrangements makes exact theoretical solutions of associated structural problems almost impossible, the role of theory should be that of developing guides or markers to which observations and experience can be related. The author in this paper has outlined the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Some important practical considerations result—especially in regard to horizontal stresses—when theory is compared with full-scale experience. In the field of engineering activity, specific examples of close agreement between theoretical prediction and structural performance are rare. Particularly is this so for the case of rock slopes, where, owing to the complexity of the natural arrangements, it is quixotic to expect exact theoretical solutions to the associated structural problems. The role of theory is rather that of developing signposts or guide rails to which observations and experience can be related. It is with this in mind that the present paper has been prepared; the author's aim has been to set out briefly the results of a theoretical study of highly idealized models which represent both granular materials and jointed rock. Despite the idealization of the problem, it will be seen that the theoretical conclusions are in accord with full-scale experience, particularly as far as horizontal stresses are concerned, and they point to some important practical considerations. CLASSIFICATION OF ROCK SLOPES At the risk of over-simplification, an attempt has been made to classify the problem of rock slopes into three broad categories with respect to internal stress systems. These are illustrated in Fig. 1. It is tacitly assumed in this classification that the strength of individual particles is very much greater than the interparticle strength whether the particles are the crystals of an igneous rock (Case I) or the blocks of Cases 2 and 3. The Homogeneous Monolith: This case is representative of uniform unjointed rock. Under relatively low stress conditions the internal stress system may approximate to that of an elastic body as given by Terzaghi.' It is more usual, however, for overall stability, to consider the material as a rigid plastic which yields in shear when S =C + c tan 4> where S is the shear yield stress, o is the normal stress on the surface of failure, and C and d are empirical constants according to the Mohr-Coulomb criterion of failure. Sokolovsky has recently developed, for the first time, a series of mathematical solutions to problems involvinga C, mass subject to self-weight. He demonstrates that for such a case a semi-arch (Fig. 2) is stable. A corollary of this argument is that for a true C, d material a curved overhanging slope is possible and such an observation may well aid field identification of these materials. The shape of the curved slope face is however directly dependent on the C-value, and from the long-term point of view this is a most difficult value to establish with any degree of confidence. It is customary to measure C and 0 in some form of shear test—usually a triaxial compression test—on core specimens sampled from the rock, and as far as the author is aware the present case is the only one in which, as far as overall stability is concerned, such tests are

Jan 1, 1961

By H Haas

H. HAAS, San Francisco, Cal. (communication to the Secretary?). -Fig. 1 plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on' the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would he well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that "two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saving that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient, demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the Southwest, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market.

Jan 5, 1917

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004

By G. E. Johnson

Batch tests of coals and coal-derived materials were made by the Bureau of Mines to determine their effectiveness in removing organic contaminants (COD or chemical oxygen demand, comprising those organic compounds that can be chemically oxidized, and ABS or alkylbenzene sulfonate, common household detergents) from the final effluent of secondary-treated waste waters. The adsorptive capacities of flyashes, coals, including at least one sample of each rank found in this country, pretreated coals, and miscellaneous materials including commercial chars and coke, were determined and compared with that of granular activated carbon. The coals, though not as effective as activated carbon, possess an economic advantage--they are relatively inexpensive, and they can still be burned as fuel without any loss of fuel value after use in waste¬water treatment. A hvcb coal was found to be one of the best, having about one-fourth the capacity of activated carbon for COD, adsorbing about 4 percent of its weight before it became saturated. Several coals contained constituents that added to the COD content of the treated water. Thus knowledge of the performance of the coal is necessary to insure selection of a proper coal as adsorbent.

Jan 1, 1966

By Dupuy. Leon W., R. T. C. Rasmussen, W. A. Calhoun

"INTRODUCTION For many years it has been known that low-grade manganese deposits occur in the bluffs along the Missouri River Valley. Frequent attempts have been made to develop the ore and to produce a marketalble commodity but they have had little success. Under pressure of the war emergency and the shortage of manganese, the attention of the Federal Bureau of Mines was directedtoward the deposits.Manganese-bearing shale occurs from a point near Pierre, S. Dak., down the river to the Rosebud bridge near the Nebraska line (1).5/ The Bureau of,confined its work to the more accessible central portion of the deposits near Chamberlain, S. Dak. The ore occurs principally as concretionary nodules in the form of iron and manganese carbonates (manganosiarite and perhaps some manganocalcite; rhodochrosite has not been identified). At the surface the carbonate is often broken down so that the oxide of manganese gives the nodules a black The matrix or host rock is generally known as Pierre shale, composed of ""interbedded layers of bentonite, an altered volcanic ash, and dissemi¬nated bentonite particles,"" (2) and montmorillonite-beidellite clay minerals (3). The shale weathers to the very sticky gumbo characteristic of South Dakota and well-known to hunters and travelers in the area.The area selected for the experimental mining and pilot-plant work discussed in this report lies about 8 miles westerly from Chamberlain and is a few hundred feet north of U. S. Highway,16, on land owned or controlled,by M. Q. Sharpe of Kennebec, S. Dak., and the General Manganese Corp."

Feb 1, 1946

By William H. Langer

The annual consumption of sand and gravel aggregate in 2006 in the Phoenix, AZ metropolitan area was about 76 Mt (84 million st) (USGS, 2009), or about 18 t (20 st) per capita. Quaternary alluvial deposits in the modern stream channel of the Agua Fria River west of Phoenix are mined and processed to provide some of this aggregate to the greater Phoenix area. The Agua Fria drainage basin (Fig. 1) is characterized by rugged mountains with high elevations and steep stream gradients in the north, and by broad alluvial filled basins separated by elongated fault-block mountain ranges in the south. The Agua Fria River, the basin?s main drainage, flows south from Prescott, AZ and west of Phoenix to the Gila River. The Waddel Dam impounds Lake Pleasant and greatly limits the flow of the Agua Fria River south of the lake. The southern portion of the watershed, south of Lake Pleasant, opens out into a broad valley where the river flows through urban and agricultural lands to its confluence with the Gila River, a tributary of the Colorado River.

Jan 2, 2010

By Brad H. A Brown, J Paul Tidman

To design a blast, one must give consideration to safety, economics, geometry, geology, production needs, and a variety of other requirements. To compare designs requires the time to develop alternatives, analyze, and then improve on them. A number of tools are available to assist with the first set of requirements, however they are poorly integrated. SHOTPlus is a program to improve the efficiency of blasting operations, by combining measurement and blast design tools, and offers the user the time and means to modify designs and explore alternatives.

Jan 1, 1997

By G. Goellner

The thick alluvial sand and gravel deposits along the base of the San Gabriel mountain range in Southern California area have been mined for construction aggregates for over 100 years. Encroachment of high-density urban populations in this area has led to concentrated mining in a handful of open pit mines with single production faces reaching up to 55 m (175 ft) in height, and long transportation distances from the pit to the processing plant. Aggregate producers have responded to these challenges by developing innovative mining systems which enable low-cost, full-face mining of the alluvial material, and low cost delivery of this material to the plant.

Jan 1, 2004

By B. J. Moore

This publication contains analyses and related source data for 352 natural gas samples from wells and pipelines in 18 States and 5 foreign countries. All of the samples were obtained and analyzed during calendar year 1974 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economics. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Sixteen previous publications have presented the results of 10,479 gas analyses prior to 1974. The first three, Bulletins 486,4 576,5 and 617,6 contain analyses and related source data on

Jan 1, 1975

By M Watts, P Lindsay

Herbert Stream, a tributary of the Waimangaroa River on the Stockton Plateau, has elevated metal concentrations and low pH characteristic of acid mine drainage (AMD). Dissolved aluminium concentrations average 8.3 ppm, iron 1.4 ppm, manganese 0.69 ppm, and zinc 0.12 ppm and pH ranges from 2.8 to 3.2. Flow rates range from 2.3 to 26.6 L/s with an average of 5.3 L/s. To determine the effectiveness of different treatment strategies, a small amount of the AMD was diverted through three small-scale passive AMD remediation systems over an eight month period. These included a reducing and alkalinity producing system (RAPS), a limestone leaching bed (LLB), and an open limestone channel (OLC). Both the RAPS and the LLB performed well, effectively removing metals and restoring pH. The RAPS lowered aluminium concentrations by up to 99%, iron 97%, manganese 95%, and zinc 80% and the LLB lowered aluminium concentrations by up to 99%, iron 99%, manganese 92%, and zinc 91%. The pH was restored to between 6.4 and 7.4 by the RAPS and to between 7.3 and 7.9 by the LLB. The OLC performed well as long as the residence time was similar to that of the other treatment systems. OLC removal rates for aluminium was up to 99%, iron 94%, and manganese 21%, and the pH was restored up to 5.6. Due to its simplicity and effectiveness, it is proposed the LLB be constructed to fullscale size to treat the entire Herbert Stream.

Jan 1, 2007

By John Songstead

INTRODUCTION The Bunker Hill mine, located at Kellogg, ID, in the Coeur d'Alene mining district, has been a major pro¬ducer of lead-zinc-silver ore since 1887. Since its dis¬covery, it has produced over 25 401 171 t (28 million st) of ore from 20 to 25 veins and ore zones. The mine now covers an area of approximately 1.609 km (1 mile) in length and 0.8 km (1/2 mile) in width and extends from 1097 m (3600 ft) above sea level to 488 m (1600 ft) below sea level. Production is presently at a rate of 1542 t/d (1700 stpd). During 1965, a new stoping method, the Bunker Hill pillar system, was developed to enable the profitable mining of large, low-grade zinc ore bodies. The system was specifically designed to in¬corporate the Atlas Copco T26GH rubber-tired loaders. High productivities were achieved, and the method was adapted for mining the higher grade stopes where large timber square sets are utilized. This results in nearly 100% extraction. GEOLOGY The area encompassing the Bunker Hill mine lies immediately south of the Osburn fault, a major east-west striking, deep-seated strike slip fault which is the dominant structural feature in the Coeur d'Alene district. The Bunker Hill forms a series of veins and mineralized zones which occur as link structures, tension fractures, and breccia zones in folded, interbedded argillaceous quartzites of the Revett and St. Regis formations of the Precambrian belt series. The Rosco ore body is predominantly a zinc ore body above the Cate fault, which is presently known to occur from the 13 level. [elevation 488 m (1600 ft)] to the 1600 level [elevation 304 m (1000 ft) ]. These ore bodies are stringer zones with at least one dominant 1.8 to 4.5 m (6 to 15 ft) wide band of ore. They dip 0.09 to 0.26 rad (5° to 15°) steeper than the local 0.61 rad (35°) dip of the Cate fault, and also deviate 0.26 to 0.52 rad (15° to 30°) in strike from the Cate. Because of the flat dip and fractured weak hanging wall, normal cut-and-fill mining has not proven practical in this ore body. The mechanized timber methods described in the next section and the Bunker Hill pillar system are the mining methods successfully used. MINING METHODS While pillar stoping and mechanized cut-and-fill stop¬ing methods were obviously superior to the widely used timber stoping methods, as far as cost and productivity

Jan 1, 1982

Major producers posted 25¢-per-pound increases on cadmium, raising their domestic quotes to $2.75 per pound. COBALT: Cobalt consumption in February, exclusive of salts and driers, increased by 21 percent compared with consumption in January. Significant increases in consumption occurred in cutting and wear resistant materials, welding and alloy hard-facing rods and materials, magnetic alloys, and other alloys. The major sales agency for cobalt in New York reportedly announced price increases, effective April 15, 1976, for cobalt metal, powders, and oxide. The new price for 250 kilo (551 lb.) drums of cobalt metal (granules or electrolytic cathodes), f.o.b. Port of New York, was quoted at $4.40 per pound. This is the first cobalt price increase since January 23, 1975, and is the result of a price increase by Sozacom, the official Zairian sales agent. Other cobalt producers are expected to raise their prices in line with the new quote.

Jan 1, 1976

By Kot F. Unrug

In the premining stage of engineering design, the only available data are obtained from core drilling. It is often not sufficient for a realistic design of strata control. During the development, an access to the geological formation is created, enabling in situ testing. Obtained data can be utilized accordingly to improve preliminary design. The available methods for testing are described with emphasis on their application for a longwall system. The optimum design ensuring continuous operation of the high output longwalls is critical because their downtime is very expensive. Optimization of ground control measures also has the potential for substantial savings by elimination of unnecessary support.

Jan 1, 1994

By K. Goshtasbi

In this paper a genetic algorithm is used in a heavily jointed rock mass in order to investigate the critical circular slip surface and modification of slope surface. This method was applied to the southern wall of the 6th Golbini Jajarm bauxite mine. The mine is the largest bauxite deposit in Iran, located to the northeast of the town of Jajarm in the Khorasan province. Estimated reserve of bauxite in this deposit is about 160 million tonnes. Field and laboratory investigations were conducted in order to determine rock mass behaviour. A genetic algorithm code that uses the Simplified Bishop method as an objective function was developed for findingt he safety factor of circular slip surfaces. Sensitivity analysis was applied to determine the optimum values of the genetic algorithm variables, such as population size, selection method, crossover and mutation rates. After finding the critical circular slip surface, slope modification is carried out by removing unstable sections from marked critical slip surfaces, and this process is repeated until the last unsafe section is removed. Based on this code, modification occurred during 7 steps, by reaching a safety factor of 1.3 in the last step. Finally, the modified slope angle of the southern wall of the 6th Golbini Jajarm bauxite mine was determined to be 48.44 degrees. Keywords: Genetic algorithm, slope modification, circular slips surface, 6th Golbini Jajarm bauxite mine .

Jan 1, 2008

By E. E. White

(Cleveland Meeting, October, 1912.) IN, August, 1911, I read a paper before the Lake Superior Mining Institute' on surveying and sampling diamond-drill holes. The present paper gives a more thorough description of these methods, together with a few changes and notes suggested by further experience. Since August, 1911, the methods, used constantly by the Cleveland-Cliffs Iron Co., have been developed to a higher degree of efficiency, and have given great satisfaction. Until a few years ago but little attention was paid to the determination of the actual course of drill-holes, to the accurate sampling and analysis of the material, or to the scientific location of the drill-holes. It has now been common practice for several years in many districts to test the inclination of drill-holes by etching glass tubes with hydrofluoric acid, but the direction of deviation from the vertical has not often been determined. Methods of determining the direction by means of a compass were first developed in connection with drilling in Victoria. The latest method used on the Rand in South Africa has been recently described by John I. Hoffman.2 In the same paper Mr. Hoffman describes an ingenious method of wedging-off a drill-bole so as to start new holes at several successive points. By this means a hole can be deflected in any desired direction, and the curvature can be controlled to a considerable extent, provided the rock is soft enough to permit the hole to be wedged off. Unfortunately, in the Lake Superior district, the jasper iron-formation is so hard that it is very difficult, if not impossible, to do this. I tried to deflect one hole so as to avoid drill-rods stuck in the hole, by using a 1 Proceedings of the Lake Superior Mining Institute, vol. xvi., pp. 100 to 120 (1911). 2 Recent Practice in Diamond-Drilling and Borehole Surveying, Bulletin No. 91, Institution of Mining and Metallurgy (Apr.. 11, 1912).

Nov 1, 1912