Search Documents

By I. Gaballah

The electrochemical behavior of a chalcopyrite concentrate having a high pyrite content was studied in HC1 by potentiodynamic, potentiostatic and galvanostatic experiments using a cell having separate anodic and cathodic compartments. Anodic oxidation of chalcopyrite particles was realized both by their contact with the cunent feeder and by reaction with ferric and cupric ions. An increase of current leads to a more selective dissolution of chalcopyrite. Surface passivation was observed after an electrolysis time related to the cell current. Cathodic reduction of chalcopyrite concentrate seems to be more promising. Almost complete conversion of chalcopyrite to a copper sulfide (Cui.8.S) is observed, whereas no reaction of the pyrite was detected. This confirms the possible selective dissolution of copper from the chalcopyrite concentrate. Copper sulfide obtained by cathodic reduction was leached using a cupric chloride solution.

Jan 1, 1994

By M. Elbert Nigri

Radioactive wastewaters from nuclear source of electrical energy production need to be treated and disposed of properly. Sr, Ca, Mg and Ba are common elements in this effluent, which can cause incrustation in process equipments and being unsafe to human health (90Sr). Fixation of CO2 can be applied to remove the ions mentioned before and to provide a solution where CO2 is sequestered and the deleterious elements precipitated, becoming one of the possible steps to reuse the water into the process. Moreover, removal of several metals from distinct wastewater has been evaluated using bone char through adsorption. The chemical similarity between calcium and strontium makes the exchange of these two metals favorable in the hydroxyapatite structure contained in bone char. This paper evaluated the combined action of precipitation and adsorption process with injection of CO2 and bone char addition in simulated nuclear wastewater. Removal levels of 89.0% (Sr) and 83.3% (Ca) were obtained in the combined process. The presence of bone char as seed increased the precipitation kinetics, allowing a Sr removal of 85.2% in five minutes, higher than 75.3% obtained in absence of seeds. However, removal of 91.6% (Sr) and 89.8% (Ca) were obtained in absence of seeds at 24 h. Analysis of solids have evidenced that CO2 was consumed to precipitate the metals as carbonates, since the hydroxides are formed at higher pH’s.

By C. J. Beyke

In recent years recycling of household batteries has received increasing attention, primarily for environmental reasons. This article reviews the major battery types and some of the technologies available to recycle them. It also discusses issues such as collection and sorting which are related to battery recycling in the United States. Finally, results from research being conducted by the U.S. Bureau of Mines on the reclamation of nickel-metal hydride, alkaline, and zinc-carbon batteries are presented.

Jan 1, 1995

By Akira Yazawa

Experimental results for the distribution ratios of various elements between the slag, matte and/or copper in the silica-saturated copper smelting system were summarized. The experiments were carried out under an oxidative smelting condition with S02 gas flow, and also a reductive smelting condition equilibrating with metallic copper or iron. To evaluate the results thermodynamically, the availability of one atom cation base expression for the constituent compounds is emphasized from both of theoretical and practical standpoints. Both of oxidic and sulfidic dissolutions in slag are postulated for some elements such as copper, nickel and lead., and the experimental results are reasonably explained thermo-dynamically. The results for the mutual solubility between matte and ferrite slag and the distribution of minor elements between liquid copper and ferrite slag are also discussed.

Jan 1, 1983

By M. Opler

Presently, only a few large copper refineries are able to produce Grade A cathodes from copper scrap. Today's technology needs large plants for smelting, converting or refining the main impurities and casting the anodes for electrolytic refining. A new ECUPREX® PROCESS, by-passes all pyrometallurgical operations and produces directly copper cathodes starting from copper scrap with high lead and tin contamination. Copper scrap from chopped cables, copper cements and electronic scrap are suitable feed for ECUPREX® PROCESS. This process uses a non-conventional electrolyte and produces a surprisingly high quality, smooth cathode assaying only few ppms of total metallic impurities. Bench-scale work followed by a successful mini-pilot plant run, has led to the construction of an operating pilot plant equipped with a 1,000 Ampere cell. The results of the operations of this pilot plant are presented and described in this paper.

Jan 1, 1995

By D. M. Hausen

Applications of process mineralogy to the exploitation of molybdenum ores begins with early exploration and continues through the evaluation of mineralized prospects, to amenability testwork and pilot plant studies, to the development of a mineable orebody and to the development of a viable process for recovery. After plant construction, a broad range of products from a wide selection of sampling locations, i.e. grinding circuit, flotation cells, smelters and roasting kilns. etc., are evaluated analytically and microscopically, followed by periodic troubleshooting of problem points. The various crystalline phases of molybdenum that occur naturally and throughout various hydrometallurgical and pyrometal1urgica1 processes are identified and characterized by a variety of instrumental methods, including XRD-XRF, optical and electron microscopy, infrared spectrographic and differential thermal analysis.

Jan 1, 1989

By Mariane Costalonga de Aguiar, Carlos Mauricio Fontes Vieira, Sergio Neves Monteiro

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850, 950 and 1050°C. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at 1050°C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antonio de Padua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antonio de Padua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption [3,4]. To avoid this problem, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2011

By G. Van Weert

Refractory gold ores and auriferous concentrates containing silver tend to form refractory silver jarosites during pressure oxidation. Earlier work with pure Ag2S has shown that the addition of iodine species to the autoclave feed yields cyanide soluble iodargyrite (Agl) instead. Near complete silver extractions from the autoclave product were obtained at a I-/Ag+ ratio of 5 or more. This paper reports on the pressure oxidation and cyanide leaching of two industrial refractory (arseno) pyritic silver-bearing concentrates: 1. from Peru (sulphosalts) and 2. from the USA (pyrite, with acanthite occlusions). While using a I-/Ag+ mol ratio of only 1 in the feed, it has been possible to obtain 98 and 97% Ag extraction from the two autoclave products by cyanide leaching, respectively. This compares to 11 and 54% Ag extraction from the as-received concentrates and 4 and 15% Ag extraction, respectively, after pressure oxidation without KI present. The results of the testwork are discussed in terms of concentrate mineralogy and pressure oxidation conditions.

Jan 1, 1994

By G. Lindkvist

Roasting of concentrates with high impurity levels is normally done in multiple- hearth furnaces where the concentrates are heated with oilfired burners in order to remove As, Sb and Bi before the final sulfide oxidation. Although it is a countercurrent heat exchange process it uses a lot of oil. In order to develop an energy saving, and from a working environmental point of view a less harmful process than the multiplehearth process, pilot-plant tests have been done in a two-stage fluidized bed for partial roasting. The test materials have been As-rich concentrates with 8-25 % As some 5b and Bi. The Cu-content was 0-28 %. The tests have been successful with <0.3 % As,in the calcine and with an elimination of 5b between 80 and 90 %. In order to achieve the proper conditions for good impurity removal, 1.e. right temperature,residence time and sulphur potential, the tests were performed in a special designed roaster. The roaster consists of two beds with the facilities for recirculation of calcine, preheating of the blast, and possibility to use oxygen enrichment. The construction makes it easy to control the reactions that generate the heat in the bed and reduce the amount of dust that passes through the cyclones. As two roasting steps are used, the possibility to obtain optimal conditions for impurity removal is improved and the calcine can either be smelted to a normal matte, or after being dead-roasted in the second stage, be leached in the normal way for gold extraction. The calcine was smelted with slag. The matte and the slag obtained had low quantities of impurities in the matte and a favourable distribution of impurities to the slag.

Jan 1, 1983

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro, Diogo Neves Henriques

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850 to 1100oC. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at temperatures above 1000 ° C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antônio de Pádua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antônio de Pádua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [3,4]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2008

By B. Zeytuncu, O. Yucel, O. H. Celik, M. H. Morcali

"The Taguchi method was used as the experimental design to determine the optimum conditions of cementation behavior of the ruthenium chloride solution. Cementation was carried out using metallic zinc powder. The experimental conditions were studied in the range of 25-45°C for reaction temperature (A), 30--60 min for reaction time (B), 0.5-1.5 for pH of solution (C), and 30--50 mg for zinc powder (D). Experimental parameters and their levels were determined in the light of preliminary tests. Orthogonal array (OA) L9(34) consisting of four parameters each with three levels, was chosen. The optimal conditions found for ruthenium, such as a reaction temperature, reaction time, pH of the solution and mass of zinc, are respectively: 45°C, 45 min, 1.5 and 50 mg. Under these conditions, the ruthenium cementation efficiency obtained by theoretically and experimentally was in good agreement, which were 99.8% and 99.7% respectively."

Jan 1, 2013

By Suresh Sundarraj

A diffusion mass transport model for predicting the microsegregation in a solidifying and coarsening dendritic mushy region of a binary alloy is presented. Two versions of this model are tested; one based on expressing the solute concentration in terms of mole fraction and the other on expressing the solute concentration in terms of mass fraction. On comparing previous model data sets and conditions, used in the analysis of Aluminum-Copper systems, a number of inconsistencies emerge. These inconsistencies are resolved on identifying a single set of data and conditions which take account of compositional density changes, "non-linear" thermodynamics and dynamic coarsening. An additional investigation is carried out to study the effect of assumed cooling mechanisms.

Jan 1, 1992

By Susanne Pignolet-Brandom

Reflected light microscopy, and scanning electron microscope energy dispersive spectroscopic analysis and backscatter electron images were used to determine if a "slick dross" with undesirable handling properties has an assemblage of phases distinct from normal dross. This study has found that in the normal dross the most abundant lead phases are lead sulfide and lead metal and the most common copper phases are copper-iron sulfide and copper sulfide. In the slick dross, the most abundant copper phase is copper-lead sulfide and the most common lead phases are copper-lead sulfide and lead sulfide. The resulting mineralogical information has provided additional insight into the causes of the handling problem and the reaction mechanism for the formation of normal and slick dross

Jan 1, 1988

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By Peng Jianping, Feng Naixiang, Di Yuezhong, Wang Yaowu, Pan Xijuan

A vacuum silicon thermal reduction lithium process is developed in present work which used lithium hydroxide, alumina and calcium oxide as raw materials. The process contains two steps, which are that Li5AlO4 clinker is prepared in ambient environment, and that metal lithium is extracted from Li5AlO4 clinker with ferro-silicon alloy as reductant in vacuum. On the basis of thermodynamic analysis and investigative experiments, feasibility of this process is proved. The results show that Li5AlO4 can be generated by calcination lithium hydroxide and alumina, the burning loss is above 31% under the conditions of calicination temperature above 750℃ and time more than 90min. The main phases of calcination product are Li5AlO4 and CaO. When the calcination product is reduced by ferro-silicon alloy in vacuum, the lithium reduction ratio can be over 80% under the conditions of reduction temperature 1200℃ and reduction time 60min.

Jan 1, 2014

By H. Y. Sohn

"The nonferrous production industry has gone through a remarkable transformation in recent years in terms of developing and adopting new technologies. Technology innovations have largely been driven by the need for greatly improved environmental protection in addition to increased productivity. One of the most notable aspects of the new technologies is their ability to reduce the emission of sulfur and other pollutants to extremely low levels.The current industry trends towards more environmentally friendly technologies are bringing about additional benefits of developing more efficient, technically advanced, and continuous processes in closed reactor vessels. Key aspects of these modem trends include the use of increased oxygen enrichment in the process gas, better process control, reduced manpower requirements, and plant operations with more skilled personnel.Computer simulation and modeling of complex processes have become more reliable, realistic, and thus increasingly useful in metal production. Some of the notable examples are reviewed.Finally, the need and advantages for value-added production in the nonferrous industry are discussed.I. IntroductionMost recently commissioned technologies for nonferrous metals production have been developed largely in response to environmental concerns. One of the most remarkable improvements made by the nonferrous industry in the last decade has been the rapid increase in sulfur capture. Before the start of the last decade, 90% capture of sulfur was considered good. Since then, strict emission regulations have become the norm in advanced societies, although smelters in many parts of the world still operate with limited pollution control. Other emissions and discharges have also been substantially reduced, resulting in much improved working conditions and worker hygiene in addition to the overall environmental protection. The development of the more environmentally friendly technologies has accompanied other advantageous advances made in the nonferrous industry, i.e., the trend towards more gas-tight, continuous processes and larger plants. This has increased the competitive edge enjoyed by the industry in the industrial countries, offsetting the higher costs of labor and pollution abatement that they have to overcome in those countries. Experience has shown that clean technology often leads to a profitable business, because its adoption forces the concomitant advancement of related technologies in addition to the avoidance of penalties imposed by the public on pollution-prone industries. Needless to say, there are other driving forces for new technologies such as reduction of operating and capital costs, improved product quality, and energy considerations in terms of reduced consumption and utilization of readily available sources."

Jan 1, 2000

By Dajian Wang

To obtain the thermodynamic properties of a multicomponent liquid alloy system over the whole range of concentration at an arbitrary temperature, the free volume cell theory has been applied to derive the formula of activity coefficients of liquid solutions based on the infinitely dilute solutions at some temperature. The linear logarithmic relationship between activity coefficients of binary dilute solutions and reciprocal of absolute temperature have been verified, and are in good agreement with the experimental values from the literature. The Monte-Carlo algorithm was used to calculate the nonlinear end value equations of binary systems, then the free volume parameters obtained were correlated with the activity coefficients of liquid binary, ternary, and quaternary systems at an arbitrary temperature. Three dimensional a-X-T diagrams of some binary systems representing the temperature and concentration dependence of activities were plotted. The calculated results regarding non-ferrous alloy systems have been statistically examined with the experimental values from the literature. Hence, this simple approach could be useful for analyzing thermodynamic properties of liquid alloy systems.

Jan 1, 2000

By Zizheng Zhou

The separation of cobalt from other base metals can be achieved using diffusion dialysis in a two-compartment reactor separated by an anion exchange membrane. In this work, a Neosepta AFX membrane was used to study the separation of various metals in an acid-chloride solution. The separation of one metal from another was investigated on the basis of the various chloro-complex stabilities. The metals investigated included cobalt, nickel, copper(II), iron(III), aluminum, zinc and cadmium. The impact of several critical experimental conditions, including the initial metal and chloride concentration in the feed solution and their initial concentration in the receiving solution, on the separation factor and the metal transfer rate is reported in this work. Effective separation of different metal pairs was achieved under the experimental conditions.

By Keiji Okumura, Jiayi Shan, Jian Yang, Masamichi Sano

"A new method of deoxidation and desulfurization of molten iron with magnesium vapor has been developed. An immersion tube, which was filled with pellets of the mixture of magnesia and carbon powders, was put into the molten iron. Magnesium vapor produced by carbothermic reduction of magnesia inside the tube was injected directly into the molten iron with argon carrier gas. The effects of temperature and carrier gas flow rate on deoxidation and desulfurization were investigated. A mathematical model of the reactions was developed. The rates of deoxidation and desulfurization were controlled by mass transfers of magnesium vapor in the gas-phase and oxygen and sulfur in the liquid-phase. This method may offer high efficiency for magnesium deoxidation and desulfurization of molten iron.IntroductionMagnesium is a strong refining agent in steel-making processes1 • At steelmaking temperatures, magnesium has a very low solubility in liquid iron, and a very high vapour pressure2 • Deoxidation and desulfurization with magnesium take place essentially through the interaction of magnesium vapor with oxygen and sulfur dissolved in molten iron, and magnesium can change chemical composition of nonmetallic inclusions3 • However, addition of magnesium to the steel bath is dangerous and does not give high efficiency in the refining process4 • Furthermore, as a refining agent, the price of magnesium is higher than aluminium and CaO fluxes. In the present study, a new method of the deoxidation and desulfurization of molten iron was developed using magnesium vapour in-situ produced by carbothermic reduction of magnesium oxide. Pellets made of mixture of magnesia and carbon powders were charged into an immersion tube, which was made of alumina or graphite. The magnesium vapor was injected directly into the melt. The effects of pellet mass, experimental temperature and carrier gas flow rate were studied on the refining rate. A mathematical model of the refining reaction was proposed on the basis of the experimental results."

Jan 1, 2000

By Juan Hernández Ávila

This work studies the Molybdenum effect on the microestructure, mechanical properties of an as-cast ductile iron. For this study five ductile irons with different amounts of Molybdenum each were made in an induction furnace. In this material nodule count and nodularity is affected by the Molybdenum additions; The iron´s matrix, nodules and the phase were analyzed using scanning electron microscopy detecting Molybdenum only in the matrix. Mechanical properties such as hardness, microhardness, tensile strength and yield strength show increments as the Molybdenum amount is increased. In the same way, ferrite and pearlite phases display a variation in their percentage as the contents of the alloy element increase. This element has a marked influence on the pearlite interlaminar spacing. From the obtained results we conclude that Molybdenum in these quantities dissolves in solid ferrite solution during the solidification process, improving the material´s mechanical properties.

Jan 1, 2009