Search Documents

By H. L. Fraser

A review of the possibilities of performing microchemical analysis in thin sections using a combination of scanning transmission electron microscopy and energy dispersive spectroscopy of x-rays is given. Particular attention is paid to the factors that limit accurate analysis at the highest spatial resolution. As an example of the use of these techniques applied to a potential problem in minerals processing, the identification of iron pyrite and pyrrhotite particles in Illinois, Herrin #6 coal is presented.

Jan 1, 1981

By S. P. Vanka, B. G. Thomas, S. Sivaramakrishnan

"During the continuous casting of steel, transient 'flow events can be very important to the generation of quality problems, such as shear entrainment, surface level fluctuations and bubble entrainment. These phenomena can be better predicted using Large Eddy Simulation (LES) models than the K-E models, which have been extensively studied. In this work the turbulent transient flow in a water model of a continuous caster has been both simulated using LES models and measured using Particle Image Velocimetry (PIV). The results of PIV and LES have been compared to validate the LES model and also to enhance the understanding of the prominent transient features of the flow field. The flow near the top surface in PIV was found to contain periods of 5-1 Os when the velocities were three to four times their mean values, which is of importance to the shear entrainment of the liquid flux. In both simulation and PIV the upper roll structure is found to change chaotically from a single large recirculation structure to a set of distinct vortices. The inlet swirl in PIV is seen to persist more than halfway across the mold, causing a characteristic staircase velocity vector pattern when viewed in a plane parallel to the wide faces. The lower rolls in PIV are significantly asymmetric for very long periods of time (- I-hour) and go through a repeating sequence of features. One of these features involving a short circuit between the upward and downward flow in the lower roll is also seen in the simulation and is of significance to bubble entrapment.IntroductionThe turbulent flow through the nozzle and in the mold of the continuous caster has been studied extensively using computational Reynolds Averaged Navier Stokes (RANS) models of turbulent flow [1,2]. Defects, such as internal inclusion of liquid fl4x through surface shear, pencil pipe defects due to bubble entrapment, surface defects due to level fluctuations are caused by transient flow phenomena oc'curring in the mold. These phenomena can be better predicted using transient Large Eddy Simulation [3] or ""LES"" models."

Jan 1, 2000

By N. L. Piret

Primary and secondary copper smelting dusts are being generated in varying quantities with very dissimilar characteristics due to the different compositions of feed materials and the type of process utilized. After categorizing the multitude of dust types, the criteria for on-site and off-site recycling of smelter dust in terms of type and concentrations of the accompanying elements are established. Thereby, consideration is given to the important aspects of: ? optimization of copper recovery ? quality of copper product ? valorization of accompanying elements ? elimination and disposal of deleterious impurities ? minimization of impact on operation ? effects on operating costs ? environmental impact of dust treatment on overall process Existing commercial, emerging and proposed copper smelting dusts, pyrometallurgical as well as hydrometallurgical, treatment schemes are reviewed and evaluated technically, economically and environmentally in an attempt to streamline the vast number of proposed options. Thereby, the high selectivity achievable in hydrometallurgical dust processing due to it being complementary to the smelting process is expected to be given increased consideration.

Jan 1, 1995

By J. Fraser Forbes

"The meaning of the term ""process control"" has evolved significantly since its widespread use began in the manufacturing industries in the 1940s. Further, the scope of process control applications has drastically increased both in terms of the breadth of industries using process automation technologies and the vertical integration of these technologies within a single industry. This evolution and integration of process control technologies within the manufacturing industries has proceeded to such an extent that process automation is an integral part of modern business practices.This paper will examine the current status of process control technology from simple process regulation through process performance optimization to business planning. Each layer of the operations automation hierarchy will be discussed both in. terms of the current state-of-the-art and the directions in which these technologies are evolving. The key tools and tasks necessary for success at every level of the automation hierarchy will be introduced. Finally, the critical challenges that must be faced in accomplishing the goal of complete Computer Integrated Manufacturing (CIM) will be described.Finally, although this paper addresses issues of practical importance to any manufacturing company, the discussions will be framed in terms of the particular challenges facing and the opportunities available within the materials manufacturing industries."

Jan 1, 2000

By R. Angulo

Carbon nanotubes (CNTs) have recently emerged as materials with outstanding properties. This has promoted their consideration as reinforcements for other material systems, such as ceramics. However, one of the fundamental problems with producing CNT-reinforced ceramics is the effective dispersion of CNTs during processing. This has been successfully carried out recently using organic solvents. This paper is a preliminery investigation into the rheological behavior of aqueous CNT-alumina slips, with the objective of moving towards a more environmentally friendly aqueous tape casting process for the production of CNT-ceramic composites.

Jan 1, 2008

By Renxing Li, Yongyong Gong, Yufeng Cheng, Zhenxing Yin, Xin Cao, Qijie Zhai

"The influence of electric current pulse (ECP) on the solidification structure of SUS430 ferritic stainless steel (FSS) was investigated in the current study. The technology of ECP has been widely used to improve the properties of metals with relatively low cost. The parallel electrodes were inserted into the free melt surface to constitute a current loop. The different influences of three parameters on solidification structure were studied by changing the peak current value, frequency and treating time respectively. The results indicated that the ECP significantly increased the number of equiaxed grains of SUS430 FSS. The as-cast structure without ECP treating was almost wholly columnar, while the number of equiaxed grains of the specimen, which was treated 3min with a peak current of 400kIA, increased to 2698 in the observed surface. To get the best refinement, an optimum range of these three parameters is required and the peak current value plays the most important role.IntroductionFor the lack of nickel resource and the pressure of environment protection, ferritic stainless steel is increasingly adopted to replace the austenite stainless steel because of its low nickel content and good mechanical properties. SUS430 steel is a typical example with excellent performance and relatively low price to replace the application of austenitic stainless steel[1-3]. This type of steel with high thermal conductivity coefficient, low expansion coefficient, good oxidation resistance, excellent stress corrosion resistance and other fantastic characteristics is often used to make components which need to have resistances for atmosphere, water, steam and oxidizing acid corrosion[4]. Since the developing of columnar grains and low toughness at high temperature, its products are easily crinkled and cracked during the subsequent rolling process[5]. The application of ferritic stainless steel is limited by these defects[6-8]."

Jan 1, 2012

By E. A. van Dijk

Dusts from steel-making processes contain substantial amounts of zinc. Such dusts are also a hazardous waste and dumping them becomes unacceptable from environmental point of view. Therefore processes that can recover zinc and possibly other metals from steel-making dusts are being investigated. The aim of this paper is a contribution to the more fundamental kinetic aspects of zinc reduction from silica free calcium ferrite slags. The effects of alumina, lime and magnesium oxide contents of the slag, the COICO, ratio and the effect of initial Fe2O3/CaO ratio were studied experimentally at 1400°C The results indicated that the reduction of zinc from molten slag was possibly a first order reaction. As expected higher COICO, ratios increased both the extent and the rate of reduction. It was also observed that a higher iron content of slag improved the reduction of zinc from calcium ferrite slags. This fact seems to support the proposed mechanism that zinc is partly reduced by ferrous iron to zinc vapour and that ferric iron is reduced by carbon monoxide. The reduction rate of zinc in these slags was decreased by increasing alumina content of the slag. Alumina decreased the calculated optical basicity of the slag showing the fact that reduction of zinc oxide was more favorable in more basic slags. Probably the formation of complex ions by alumina and zinc oxide such as ZnAl2O32+ lowers the activity of Zn2+ ions in the slag and hence render them more difficult to reduce.

Jan 1, 1999

By Tim B. Vander Wood

Standard methods of determining clay mineral powder aspect ratios involve manual scanning electron microscopy analyses of shadowed particles in order to measure both platelet thickness and diameter. We present a method whereby the diameters of platelets are quickly determined by automated scanning electron microscopy and their images are recorded and digitally transferred to a transmission electron microscope equipped for parallel electron energy loss spectroscopy. Thickness' of platelets whose diameters are known from the previous analyses are determined by measurement of the ratio of scattered and unscattered electrons in the beam after it has been transmitted through the platelet.

Jan 1, 1995

By J. W. Lyman

Nickel-metal hydride (Ni-MH) battery electrodes have been developed as a substitute for cadmium-containing negative electrodes. Use of Ni-MH electrodes offers enhanced electrochemical properties in many instances as well as reduced environmental toxicity. Rechargeable batteries using Ni-MH electrodes are also strong candidates for electric vehicles. During the production and secondary reclamation of these battery types, recycling procedures will be needed to prevent environmental impact caused by these wastes as well as to recover the value inherent in the scrap. The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical technology that separates and recovers purified metallic components from Ni-MH battery scrap of two types, AB, and AB,. An investigation of acid dissolution and metal recovery techniques has determined several processing alternatives that may be used to promote the successful recycling of much of the battery fabrication scrap and eventual secondary scrap. Although recovery techniques have been identified in principal, their applicability to mixed battery waste stream and economic attractiveness remain to be demonstrated.

Jan 1, 1995

By Gordon Irons, Kevin Graham, Krishnakumar Krishnapisharody

Ladle or secondary metallurgy in steelmaking is an essential process step for the production of high-quality steel. Professor David Robertson was a pioneer in the modeling of these processes, in particular gas-metal fluid dynamic interactions and the rates of slag-metal reactions. This is now a highly active area of research, and some of the recent developments in this area will be reviewed.

Jan 1, 2014

By George P. Demopoulos

n this study we have sought to highlight the critical linkage between individual reaction kinetic parameters (usually determined in small bench scale experiments) and large continuous reactor performance by focusing on the industrially significant zinc pressure leach process. To this end a comprehensive mathematical model previously developed for the description of this process was employed. In this paper we have examined in particular how small variations in key kinetic parameters impact on the autoclave&apos;s performance, i.e. attainment of autogenous steady-state temperature, zinc conversion and solution chemistry. The reaction parameters studied were: (i) stoichiometry of the marmatite leaching reaction; (ii) the activation energy of the same reaction, E,; (iii) the rate constant of the ferrous to ferric oxidation reaction, k,; and (iv) the apparent equilibrium constant for ferric precipitation, K,. This parameter sensitivity analysis was done under no oxygen mass transfer control limitations. Model predictions were found to be more sensitive to the kinetic parameters under certain conditions than others. The most dramatic finding was the one related to the small amount of sulfate produced during marmatite leaching. In connection to this it was found that the small percentage (< 5 %) of sulfate produced enhances the autothermal operational stability of the autoclave. The need for accurate kinetic parameter determination under conditions similar to those encountered in industrial zinc pressure leaching was demonstrated.

Jan 1, 1999

By J. Y. Hwang

Microwave heating is an attractive alternative to conventional heating methods because heat is generated directly within the microwave absorbing materials. It has potential to be utilized for selective heating and removal of specified components from a materials mixture. This investigation was undertaken to explore the potential of selective heating and burning of binders for foundry sand reclamation. Selected raw materials and binders used in foundry operations were tested to determine their receptivity to microwave heating. Time needed to reach 600°C and/or the maximum temperature achieved for samples irradiated by microwaves for twenty minutes under 800 W microwave power are reported. The microwave heating characteristics of the selected materials are summarized and discussed. The interactions between microwaves and the raw materials used in a foundry. such as silica sand. chromite sand and bentonite (clay) binder were studied. The results showed that chromite sand coupled well with microwave energy at ambient temperature while silica sand did not. This was expected because the major component of chromite sand. iron chromite (FeCr2O4). is a good microwave absorber. while quartz, which is the major component of silica sand, is a microwave transparent material at ambient temperature. Bentonite absorbs microwaves well because it contains a hydroxyl functional group and water molecules in its structure. It was found that the structure of bentonite was changed through microwave irradiation. Microwave heating characteristics of silica sand mixed with different amounts of bentonite binders were investigated. The presence of bentonite in the mixture improved the microwave heating of silica sand significantly. and bentonite was deactivated by the microwave processing.

Jan 1, 1995

By E. Krystad, G. Tranell

"The kinetics of boron removal from liquid silicon during slag refining, as a process step in the production of solar grade silicon, has been investigated by means of small scale mass transfer experimental series at 1600°C, using a graphite crucible. The slags were SiO2-CaO based, with or without addition of approx. 19 wt% MgO. Experiments were carried out at slag-metal ratios of 1 or 2, where the silicon initially contained approx. 250 ppm boron. The metal-slag mass transfer coefficients for boron were found to be in the order of 1-3 · 10-6 m/s and were largely influenced by slag composition. The mass transfer rate was higher for the MgO-containing slag than the slags without MgO. The final equilibrium distribution of boron between metal and slag, LB, was determined to be in the order of 2.3-3.3.I. INTRODUCTIONRecent years have seen a race in industry and research aimed at obtaining a reliable metallurgical route for production of silicon for solar cells (SoG-Si) from metallurgical grade (MG) silicon. Metallurgical routes can successfully challenge the traditional chemical routes for production of SoG-Si if they generate metal of sufficient purity while being less expensive in terms of production cost and energy consumption. Efficient removal of boron is one of the greatest obstacles in the refining of silicon by a metallurgical route, because the segregation coefficient of boron in silicon makes directional solidification unfeasible; in addition, the vapour pressure of boron is not high enough for removal by vacuum refining. However, the thermodynamic properties of boron makes removal from silicon by oxidation possible, and thus the process of slag refining of silicon has been receiving increasing attention as a method for boron removal."

Jan 1, 2012

By N. Voennann

Stillwater Mining Company operates an electric furnace at its smelter in Columbus, Montana to treat a Ni-Cu-platinum group metal concentrate along with secondary PGM bearing materials. Hatch Associates has designed several improvements to this furnace, which was originally built by others. Implementation of these relatively low cost improvements has resulted in substantial increases in furnace availability and capacity, along with reduced unit costs. ? The improvements included: ? Installation of water-cooled copper cooling elements to stabilize refractory wear and increase furnace life.- ? Improved furnace &apos;bindings, to enhance the furnace&apos;s structural integrity by improving the contact between the refractory and cooling elements, and by promoting tight brick joints resistant to matte or slag leaks. ? Adjustment of the electrode regulator to allow higher furnace power levels. ? Installation of an automated air-slide (aeration conveyor) feed system to evenly distribute the furnace feed in an insulating layer on the bath surface. This "black-top" practice reduces unit energy costs and makes available additional smelting capacity.- ? Electrode seals to reduce ingress of air that absorbs heat before exiting the furnace in the off-gas stream. The saved energy can be used to smelt additional concentrate. This paper describes the above furnace modifications, and the benefits derived from their implementation.

Jan 1, 1998

By Bingguo Liu, Daifu Huang, Jinhui Peng

"The conditions to prepare U3O8 by calcination from ammonium diuranate were optimized, and the response surface design method was applied to analyze the influence on the total uranium and U+4 of calcination temperature, calcination time and mass of sample. A quadratic equation model for the total uranium and U+4 of U3O8 was built and the effects of main factors and their corresponding relationships were obtained. The analysis of variance shows that calcination temperature and calcination time significantly affected the value of total uranium and U+4 of U3O8. The optimal calcination conditions were as follows: calcination temperature 931.83 K, calcination time 24.32 min and 43.89 g. Under these conditions the value of total uranium and U+4 of U3O8 was 84.78% and 28.02%, respectively. The validity of the model was confirmed experimentally and the results were satisfactory.IntroductionNuclear energy is clean, effective, and a sustainable from of energy. It plays an important role in overcoming the impending global energy crisis, and in reducing energy vulnerability. In addition, nuclear energy is a possible cheaper and cleaner source of energy compared to fossil fuels, with no not really, mining of uranium produces CO2 contribution to green house gases [1]. Uranium dioxide, one of the most important fuel pellets used as nuclear fuel in light water reactors, is manufactured by calcining ammonium diuranate to triuranium octaoxide, followed by its reduction to uranium dioxide using cracked ammonia at 700°C [2]. Earlier attempts to optimize the important calcination process through several common techniques have not yielded desirable results [3]. These techniques either rely on the classical one parameter at a time approach that ignores the combined interactions between physicochemical parameters, or are theoretical in nature. Furthermore, these techniques also require large number of experimental data to be generated [4]. In order to produce triuranium octaoxide in an optimized manner, which considers the interaction of different process parameters [5], there is a need to adopt a multivariate statistical technique."

Jan 1, 2011

By D. J. Murdock

Cominco Ltd. has developed a number of innovative technologies for electrowinning. The paper discusses the application of these technologies to the copper industry. Tankhouse and cell design will be discussed in addition to anode cleaning and cathode handling. Specific examples of the application of this technology to the copper industry are cited.

Jan 1, 1987

By Chen Song

Cobalt basic carbonate particles were precipitated from 1.0mol cobalt nitrate or cobalt sulfate solution with ammonia carbonate. By controlling the zeta-potential of the particles and the ionic strength of the solution, the uniform particles with ellipsoid or rod shapes were obtained. During the precipitation process, the interface tension was diminished to the minimum and therefore the Ostwald ripening and secondary nucleation were both inhibited. The morphology and the size control by zeta-potential seem to be the result of thermodynamics rather than classical crystalline kinetics. The particle sizes were in the range of 0.4-0.6, 0.3-0.4 micrometer. After thermolysis, the spinel-type C0304 particles were produced. The morphologies of C0304 particles were similar to that of their precursors.

Jan 1, 2003

By Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa

"Thermodynamic properties of impurities in molten silicon are of prime importance in developing economical production methods of solar grade silicon. In the present research work, thermodynamic properties of boron, the most difficult element to remove from molten silicon, were measured by chemical equilibration techniques at 1723 and 1773 K. Activity coefficients and self-interaction parameters of boron in molten silicon were determined by equilibrating the melt with solid BN under controlled nitrogen partial pressures. Interaction parameters between boron and nitrogen in molten silicon were also determined by equilibrating the molten Si-B alloys with solid Si3N4• Based on the data obtained, the stability diagram of the Si-B-N system was established.IntroductionPhotovoltaic power generation using a silicon solar cell is expected to be the most promising energy source, because it is inexhaustible, cleaner and more safety than conventional energy sources, such as thermal or atomic power generation. At present, expensive off-grade silicon for semiconductor (SEG-Si) is used for a solar cell production. However, if a large-scale photovoltaic energy conversion using silicon solar cell comes into wide use in the near future, silicon will be sure to be in short supply for the cell. Therefore, a development of a new large scale process for solar grade silicon (SOG-Si) production is definitely necessary, which can remove contained impurities from silicon.Among the impurities contained in silicon, boron is one of the most difficult ones to remove by a zone melting or an unidirectional solidification, because its segregation coefficient in silicon is close to unity (0.8). In addition, boron behaves as a p-type silicon semiconductor dopant and, therefore, its content in SOG-Si must be severely controlled. Although some attempts to remove boron by various metallurgical methods have been carried out [I -4], quantitative analysis has not been made due to lack in the information on the thermodynamic properties of boron in molten silicon. From this view point, the activity of boron in molten silicon was determined in the present study by chemical equilibration techniques at 1723 and 1773 K."

Jan 1, 1998

By Xun An

Slag from an electric slag cleaning furnace was injected with methane and air mixtures to facilitate the recovery of copper and cobalt. The effects of methane-to-air ratio, gas flow rate and temperature on the reduction and metal separation were investigated. The results showed that over 90 percent copper and up to 60 percent cobalt could be recovered from the slag with a gas utilisation of around 70 percent, as calculated by thermodynamic simulation. Methane-to- air ratio was a major factor affecting the rate of reduction under the present experimental conditions. Further, injection of gaseous reductants greatly enhanced the coalescence and settling of entrained metal droplets. A reduction mechanism is proposed and the factors influencing the coalescence of copper droplets are discussed.

Jan 1, 1998

By Basant L. Tiwari

An electrolytic process, based on a three-layer concentration cell, to extract magnesium from commercial aluminum alloy scrap has been examined. The process was repeatedly tested at 1025 K with two cells of d1fferent sizes, 0.6 kg and 5 kg feed aluminum, to have a better understanding of the opera ting parameters and evaluate the scale-up potential. In both cells, the magnesium content of the scrap was selectively reduced ?from 1. 1 to less than 0.1 wt.% at anodic current dens-Hy as high as 1. 1 A/cm2 with current efficiency exceeding 85%. Magnesium was recovered in the form of salt coated globules. Comparison of performances for the two cells suggests that the process can be scaled up. With further development, this process could become a viable alternative for demagging secondary aluminum.

Jan 1, 1985