Search Documents

By A. D. Neuman, C. C. Davis, M. R. Lopez, A. C. Martinez, T. A. Nothwang, F. G. Hampel, S. L. Voit

"One of the thrust areas for the Global Nuclear Energy Partnership (GNEP) program is the development of actinide bearing fuels for transmutation in a fast reactor. Mixed Oxide (MOX) fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition from which minor actinides can be incorporated for use as a transmutation fuel. The current study involves characterization of precursor powders and pellets destined for the Advanced Test Reactor in Idaho. These pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of minor actinide mixed oxide (MAMOX) with oxygen to metal ratios (O/M) of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders were characterized using a field emission gun scanning electron microscope (FEG-SEM) to determine particle morphology, size, and size distribution. An electron probe microanalyzer (EPMA) was used to characterize element distributions in the pellets.IntroductionThe fundamental purpose of GNEP is to enable a fuel recycling partnership between member nations. The customer nations utilize the fuel for electricity generation provided by and subsequently recycled by the supplier nation. The supplier nation recycles the actinide constituents, mainly uranium and plutonium, in advanced nuclear power reactors, and thus reducing waste volumes [1, 2]. Nuclear materials are strictly controlled through the International Atomic Energy Agency. One of the thrust areas supported by the GNEP program is the development of actinide bearing fuels for transmutation in a fast reactor under the U.S. Advanced Fuel Cycle Initiative (AFCI) in order to transmute long-lived transuranic actinide isotopes into shorter-lived fission products [3].MOX fuel has an extensive fast reactor irradiation history and thus is being considered for use as a baseline composition into which minor actinides can be incorporated for use as a transmutation fuel [4]. Irradiation performance data on oxide fuels with high concentrations of minor actinides is limited, which has prompted this study. This paper discusses the characterization results of precursor powders and pellets prepared for the Advanced Test Reactor in Idaho to determine the effects of including minor actinides in the fuel, and addresses two fuel test matrices proposed by Hilton et al. [3]. The pellets will have three compositions: one standard MOX composition, (U0.80Pu0.20)O1.98, and two compositions of MA-MOX with O/M of (U0.75Pu0.20Am0.03Np0.02)O1.98 and (U0.75Pu0.20Am0.03Np0.02)O1.95. The precursor powders, uranium oxide (depleted, DUO2 and highly enriched, HEUO2), neptunium oxide, NpO2, americium oxide, AmO2, and plutonium oxide, PuO2, were characterized using a FEG-SEM for particle morphology, size, and size distribution. The morphology of the actinide powders was studied in the areas of flowability and porosity in order to predict manufacturability. The MOX pellets were characterized using an EPMA in order to determine impurity levels and locations."

Jan 1, 2008

By W. G. Davenport

This chapter extends our mathematical description of flash smelting to -nitrogen in the flash furnace blast. As in chapters 4 and 5, the discussion is limited to auto thermal smelting (no hydrocarbon combustion). Hydrocarbon combustion is introduced in Chapter 9. Outokumpu flash furnace blast is a mixture of air and industrial oxygen. Most of its N2 originates in the air portion of the blast. A small portion originates as an impurity in the industrial oxygen. The nitrogen entering a flash furnace must always be heated from its input temperature, 298 K in this chapter, to its off gas temperature, -1500 K. Energy must be supplied for this purpose. With auto thermal smelting, the energy is-provided by oxidizing extra Fe-and S.

Jan 1, 2001

By Frank Field, Randolph Kirchain, Elisa Alonso, Richard Roth, Nathan Fleming

"High material prices and price uncertainty can be harmful to manufacturing firms. Increased use of recycled materials, industry-wide, can lower both material prices and price variability; moreover, increased recycling decreases the use of primary material, which mitigates price increases due to scarcity effects. These stabilizing and price lowering effects are explored using an Aluminum industry model. We show that (a) increased recycling leads to smaller price fluctuations in the presence of a primary metal supply perturbation, and (b) that the more substitutable the secondary metal is for the primary metal, the lower the overall material price is.IntroductionThe price of an industrial metal is expected to be a function of both the marginal cost of extraction and its scarcity[l-2]: where scarcity can be defined as the degree to which anticipated demand exceeds the known supply. Recycling end-of-life metal increases the apparent supply of the metal, or-in a functionally equivalent, but alternative conception-lowers the demand for primary metal; this lowers primary metal scarcity and should, theoretically, reduce its price. To the extent that this theoretical prediction holds true, recycling can provide benefits to consumers of industrial metals in the form of lower prices.Using a platinum industry model, prior work by Alonso[3] has shown that increased industrywide recycling can reduce metal price volatility because the secondary metal production (a) offsets virgin metal depletion, and (b) responds to supply-demand balance fluctuations more rapidly than the primary market. However, Platinum is not a typical industrial metal in the sense that secondary metal is perfectly substitutable for primary metal: Both primary and secondary platinum metal are functionally equivalent and have a common price. Other metals, such as secondary aluminum which is used as an example case in this study, contain varying degrees of other elements that were either intentionally added, or were inadvertently mixed in with the metal during the scrap recovery process. Consequently, different grades of scrap exist that have different profiles of elements in their composition. Depending on their particular profile of elements, more or less of a given grade can be used as a mass fraction of the final alloy-the secondary metal is not perfectly substitutable for the primary metal. For the purposes of this paper, the aluminum mass fraction of the final alloy that can be made up of secondary aluminum is termed the secondary substitutability of that grade in that alloy."

Jan 1, 2011

By Ladislav Bebar, Tomas Parizek, Radek Dvorak, Petr Stehlik

"More and more sweeping environmental regulations initiate research, development and introducing into operation up to date technologies for cleaning off-gas and flue gas generated in various branches of industry and municipal waste treatment. The following systems based on novel types of equipment are shown: thermal and catalytic treatment of waste gases polluted by VOC (Volatile organic compounds) and carbon monoxide (alternatively NOx), catalytic filtration for efficient destruction of PCDD/F (dioxins) and potentially NOx, wet cleaning of flue gases polluted by SO2, HCl and HF with a original type of homogenizer “O-element”, integrated equipment for cleaning waste gases polluted by solid particulates, SO2, HCl, HF and heavy metals (alternatively NOx or PCDD/F). The outstanding features of all equipment mentioned above are low investment and operating costs together with high removing efficiency of pollutants. These units can be used mainly in incineration plants, refineries and other chemical plants. The paper represents a review based on papers published in reputable international journals and a monograph under preparation as well as on experience from industrial applications.IntroductionIn the recent years, more and more emphasis is put on preserving clean environment. One of the most closely monitored objects of general public attention are exhaust gases, containing a number of undesirable compounds like NOx, CO, SO2, HCl, HF, fly ash a PCDD/F. These harmful species are created in chemical processes mainly in the industry, transport and energy sectors. There is therefore a strong impetus for abatement of these harmful pollutants. Sectors of industry are thus subject to emission regulations specific to various types of units. In the framework of increasing demand for a clean environment, the concerned legislation is becoming increasingly strict and requires removal of pollutants by modern methods that would ensure efficient abatement of emissions at reasonable investment and operating costs.Attention is focused chiefly on methods for decreasing harmful emissions from thermal waste treatment facilities processing industrial and municipal waste that may be subsequently applied in other sectors of industry. Units for the thermal treatment of waste not only provide means of its disposal, but may become also important sources of energy, provided that strict emissions limits are satisfied. Figure 1 compares emission limits given by the legislation for municipal waste incinerators and limits for a selection of energy sources with heat capacity up to 50 MW (see EU regulation 200/76/EC). The Figure implies that the values of emission limits for waste incineration are mostly comparable with emissions from the combustion of natural gas. Thanks to the continuing improvements of the methods for removal of harmful pollutants, the emissions from waste incinerators are typically deep below the limits."

Jan 1, 2008

By M. J. Soria-Aguilar, F. R. Carrillo-Pedroza, S. Preciado-Nuñez

"Dust originated from the Iron Blast Furnace (BF) and the Basic Oxygen Furnace (BOF) containing alkalis and zinc are not completely recycled because due affects the process efficiency. These types of dust represents an economical lost as a consequence of values contents of iron and carbon. Several processes in aqueous media have been developed to treat the steelmaking dust. This work presents a laboratory study for reduce zinc and alkali containing in BF and BOF dust, using different acid and alkaline solutions and oxidants as ozone. The results obtained show that the elimination of zinc and alkalis can vary from 5 % to 80 % depending on the treatment conditions (the solution, the oxidant and the temperature). The dust obtained from this treatment can to be recycling to the steelmaking processes to recovery iron and carbon values.IntroductionEach one of the steel making industry processes generate several sub-products and residues containing useful units of iron, carbon and other elements that are or could be recycled to the productive process. Some of those sub products are the dust from the gas cleaning system of the blast furnace and the dust from BOF reductive process; such dusts are sent to the sedimentary lagoons. The dust represent a lost of 2 % of the total iron and coal mineral’s content feed to the process.The typical iron, carbon and zinc content of the blast furnace dust is approximately 40, 24 and 0.3 % and the content of the BOF dust are 50, 15 and 0.9 % weight respectively, with physics - chemical characteristics that became them susceptible to be agglomerated and feed to the blast furnace. But the high content of zinc does not allow recycling it into the process. At the blast furnace the presence of zinc propitiate the formation of film in the furnace wall; these elements are vaporized in the low section of the cube of the furnace and they are dragged by the gases to the top and condensed again at the cube. Part of these condensed materials strongly adheres to the furnace cover harming it and reducing the empty space of that section, causing eventually a severe perturbation of the ascendant gas flux [1]."

Jan 1, 2008

By Yoshiaki Suzuki

Since 1973, Saganoseki Smelter & Refinery had operated two flash smelting furnaces together to produce 330,000 mtpy of copper. However, in 1990's, economical situation required the smelter more increased productivity to remain competitive. The program, to integrate two flash furnaces into one was carried out maintaining the same production. Modifications were done on the pneumatic concentrate drying system, concentrate feeding system, concentrate burner and furnace cooling system, etc. to double the, furnace throughput. A new large cryogenic oxygen plant was constructed replacing two old plants. Single flash smelting furnace operation has started in March 1996. This paper describes about details of modifications and operational results.

Jan 1, 1998

By Stephen C. Britten

An in-situ amperometric slag sensor for measuring the concentration of easily dissociable oxides in slags at temperatures between 1200-1600°C is being developed. The sensor provides the same information as potentiometric sensors while also providing data on the concentration of the transition metal species and the diffision kinetics within the slag. The electrochemical technique utilized in the sensor is similar to methods utilized in aqueous voltammetry.

Jan 1, 1998

By C. M. Chen

Friction stir welding (FSW) is a pure solid-state joining process, which has been widely used in joining aluminum alloys with improved properties. This paper describes a three-dimensional simulation of FSW process, running the ANSYS package of finite element analysis to study the evolutional stress in the butt-welding of aluminum alloy 6061-T6. The model incorporates the mechanical effect of the tool and thermomechanical process of the welded material. The heat source involves the friction between the material and the probe and the shoulder. Thermal history and the evolution of longitudinal, lateral, and vertical stress in the friction stirred weld are simulated. The relation between the calculated residual stresses of the weld and the process parameters such as tool traverse speed is presented. Keywords: Fiction Stir Welding, Finite Element Analysis, Thermomechanical Process, Evolutional Stress, Residual Stress.

Jan 1, 2003

By D. S. Barr

The Freeport McMoRan chlorination circuit is comprised of four related processes: ore chlorination, gas scrubbing, chlorine supply and excess hypochlorite removal ("hypo kill"). Each of these processes are described, and related to the pertinent mineralogic components in the carbonaceous ore feed to the plant. The chlorination system in use at Jerritt Canyon to passivate forms of preg-robbing organic carbon has proven to be a cost effective and efficient means to recover gold from low sulfide carbonaceous refractory ores, where gold may not be specifically associated with either the sulfides or the carbon.

Jan 1, 1987

By Sung Tae Kim

The viscosity is one of the most critical properties of slags and thus its influence on the physicochemical phenomena in metallurgical processes has been issued for last decades. The viscosity of ferrous- and non-ferrous metallurgical slags can be understood via structural investigation with spectroscopic methodologies including x-ray photoelectron spectroscopy, infrared- and Raman spectroscopy, and solid state nuclear magnetic resonance spectroscopy, etc. Therefore, the reaction kinetics such as desulfurization in ladle metallurgical furnace, reduction of FeO and MnO in electric arc furnace is strongly dependent on the viscosity of the slags. The rates of oxide (inclusion and refractory) dissolution into the slags and fluxes are governed by the viscosity. Alternatively, the structure of aluminosilicate melts also affects the thermochemical properties such as sulfide capacity, etc. These diverse applications of the viscosity-structure relationship to ferrous- and non-ferrous metallurgical processes were reviewed.

By Florian Kongoli

The optimal operation of the blast furnace depends considerably on the properties of the sinter fed into the furnace. As a result, the optimization of the sintering processes has a direct effect on the overall effectiveness of the iron making processes. In order to produce a good sinter special care needs to be taken in order to assure it has a good permeability and reducibility and it is able to retain these properties for a certain time. If the sinter starts to melt down early in the upper part of the blast furnace, where its solid state reduction is essential, permeability decreases, the gas channels get blocked, reductibility diminishes and serious problems may also follow. Among the factors that influences the above mentioned sinter properties are the oxygen potential and fluxing components. Nevertheless, their effect on the phase relations during sintering and sinter reduction conditions has not yet entirely clarified and confusion exists in literature. This quantification becomes even more important today where many new minor components such as Al2O3 and MgO enter the sinter through raw materials. This work quantifies the effect of oxygen potential and fluxing components such as alumina and magnesia on the liquidus and phase relations of the sinter primary melts in the iron rich portion of CaO-FeO-Fe2O3-SiO2 system at sintering conditions. This is carried out by the means of new type of industrial diagrams in the form of Fe/CaO vs. SiO2 that can directly help the optimization of the sintering processes.

Jan 1, 2006

By David S. Dolan

To beat capital costs of US$10 per pound of installed capacity has appeared as a major hurdle for the "third generation laterite nickel plants. Forecast costs are escalating. Where can savings come from? Ore beneficiation can reduce the tonnage rate to be processed. High pressure acid leach options include the use of indirect slurry heating and higher operating temperatures to reduce flow rates and residence time. Progress has been reported in atmospheric leaching. High counter current decantation circuit settling rates and high underflow densities reduce CCD costs. Metal recovery options include direct from leach solution to metal production, as used by Bulong and espoused by Goro, and indirect recovery as used by Moa Bay, Murrin Murrin and Cawse. Plant location impacts on the costs of tailings disposal, power and energy costs, supply of consumables and labour costs, among others. Final nickel and cobalt metal production routes are electrowinning, hydrogen reduction or some innovative routes being proposed for Goro. This paper reviews the status in these developments, with particular reference to equipment and processes that offer lower capital costs. Keywords: Laterite, Nickel, Plant, Capital Cost

Jan 1, 2004

By Alex Meystel, Diran Apelian

"In this paper, an outline is given for a theory of intelligent control (IC) of manufacturing processes (MP) based upon what all of them have in common: all MP's can be represented as distributed networks of sequential/parallel elementary ""lumped"" models; all elementary models are organized by definite input-output conditions, and by the set of constraints; all elementary models incorporate not only well defined physical knowledge, but also assumed physical knowledge, expert knowledge, expected knowledge to be obtained during the process from sensors, etc. This creates a hierarchy of elementary controllers coordinated by local coordinators of different levels up to a global coordinator. The latter verifies the adequacy of MP by using a holistic image of the process: depictogram. The structure of knowledge based controller is introduced, and the analytical/linguistic tools of control are presented. The concept entails a number of perspectives which are discussed in the conclusions.1. IntroductionIt is becoming increasingly clear to those of us in Engineering and Technology oriented fields that the so called ""service industries"" do not create wealth. Moreover, it is now accepted that manufacturing is the key to the creation of wealth from a socio-economic point of view. This appreciation of the importance of manufacturing is reflected by the transformations we are seeing in our factories, as well as the changes in both curricula and research activities of our universities. Though we find these changes to be in the right direction, there is yet much more to be done to advance the frontiers of manufacturing and materials processing as we approach the third rnillenium."

Jan 1, 1988

By Leonel Contreras

The gas treatment system, MALIGAS (in Spanish MAnejo y Llmpieza de GASes which means handling and cleaning of gas), is part of the Codelco-Chile Potrerillos Smelter decontamination plan; which includes the newly designed system for the cooling and cleaning of the gas generated from a Teniente Converter and four Peirce Smith Converters. The gas generated in the process is captured by water cooled hoods and mixed with air. Then the gas enters a cooling pre-chamber which utilizes a water cooled screen to capture and remove the coarse and semi-fused particles. At this stage; the gas loses a portion of its heat with temperature falling below 608°C which is a necessary condition to avoid damage to the pipes, ducts and other metallic structure of the gas handling system. The gas is further cooled at the Radiation Cooler to a temperature ranging between 315 and 380°C. The gas is conditioned to avoid damage to the electrostatic precipitators that are designed to clean the gas by removing significant amount of dusts from the: gas stream. This gas stream is currently discharged to the stack, however, it will be treated in a sulfuric acid plant that is currently under construction and is scheduled for commissioning during the second half of 1999. The gas handing and cleaning system has been operated without any significant interruptions. Minimal emissions of SO2 and dusts in the work place are noted. The system requires minimum maintenance. The key to the high availability of the system is due to the good, performance of he Radiation Cooler, which efficiently cools the gas before entering the electrostatic precipitators (ESPs). This enables the ESPs to remove the dusts efficiently.

Jan 1, 1999

By Takashi Yoshida

"This paper will discuss the recent situation and future of the zinc industry from the technical point of view. It includes recent problems faced by the zinc industry and technological developments. One of the biggest problems of the zinc industry is raw materials. Traditional zinc concentrate becomes much complicated with respect to its chemical and physical properties. Thus, each process faced various problems. Also, secondary resources, generating so called recycling processes, become much more important. Recycling is, of course, a very important aspect for sustainable development of society. Secondary raw material also includes a great variety of impurities not included or very low levels in traditional zinc concentrate. Some problems are caused by these impurities. To overcome these problems some technological challenges have been taking place. Details will be discussed in the symposium.IntroductionZinc is a very useful metal based on its elechtro-chemical, chemical and physical properties. The most important usage is galvernizing of steel which is used for automobile, construction and a very wide range of other indutries. Also, zinc is used for dicasting and other alloys such as brass. Smelting of zinc is different from other metal because of its electro-chemical properties. Many parameters should be controled compared with other metals such as iron and copper. Typical zinc smelting processes are the Imperial Smelting Process (ISP) and the electlolytic process. The ISP process is a pyro-metallurgical process using a blast furnace. The electrolytic process is a hydrometallurgical process. Both processes are energy intensive, and the smelting process cost is increasing because of higher energy costs. The situation of the ISP is very severe because of higher coke prices. Recently, many ISP plants have been shut down because of economic reasons"

Jan 1, 2012

By Osamu Yamamoto

In antibacterial evaluation of carbon-ceramic composites, we prepared two type composites with emphasis on carbon-ZnO system; one was porous carbon materials containing ZnO nano-particles and another was porous ZnO coated with carbon thin film. Porous carbon samples containing ZnO at highly dispersed state were prepared by carbonizing the resin exchanged by Zn2+ ion. Porous ZnO coated with carbon thin film was obtained by the pyrolysis of poly (vinyl alcohol). Antibacterial activity of these composites obtained was evaluated by measuring the changes in electrical conductivity with bacteria growth. The antibacterial activity on the composites increased with the increase of t he amount of ZnO in composite and decreased with the increase of carbonization temperature. The antibacterial activity for Staphylococcus aureuswas found to be stronger than that for Escherichia coli. No activity of the carbon samples without ZnO was observed. The occurrence of antibacterial activity was supposed to be due to the generation of hydrogen peroxide from ZnO in composite. In the present work, antibacterial activity of carbon-ZnO composites was studied in the details.

Jan 1, 2006

By Gil Bourcier

A process has been developed for detoxifying spent potliner (SPL) in which the SPL is blended with limestone and an anti-agglomeration agent and thermally treated in a rotary kiln. The process has been proven and a commercial plant is in operation at Gum Springs, Arkansas. The treated by-product material has been delisted by the U.S. EPA and is now a potential raw material for many commercial applications. Finding uses for a non-hazardous material has many advantages over finding uses for a hazardous material like SPL. Complete usage of the by-product will complete the life cycle and eliminate any landfilling of non-hazardous SPL by-products or residues. Being non-hazardous and containing compounds used in the ceramic and numerous other industries assures many potential uses for the spent potliner by-product.

Jan 1, 1994

Due to problems with old technologies more and more product designers have turned to liquid crystal (LC) displays, which have consequently experienced phenomenal growth. The success of liquid crystal displays has fostered continued development, to the point where full-color video displays have been realized which can rival. The details of the lens structure and of the devices fabrication and performance are described using the Jones matrix method. Director n can change from point to point and is, in general, a function of space.. The transition can be approached by changing the impurity concentration or, indirectly, by tuning the temperature since the pinning strengths of the random and crystal potential have in general a different temperature dependence. Light from the conventional light source or laser is passed through a polarizer and then incident on the specimen. The resist profile simulation is carried out using the combined data thus obtained. The nematic liquid crystal is clear only when a long range order exists, in the whole medium. At the nematic-isotropic, transition temperature, the medium becomes isotropic and looks clear and transparent.

Jan 1, 2006

By Michal Rzyman, Nakamura Takashi, Shibata Etsuro, Grabda Mariusz, Oleszek-Kudlak Sylwia

"Thermodynamic considerations indicate that heavy metal oxides should easily react with HBr, the main gaseous product from the thermal decomposition of tetrabromobisphenol A (TBBPA), forming low boiling point metallic bromides suitable for volatile separation. Mechanisms and kinetics of the bromination reactions must be well recognized prior to developing of a new treatment for the simultaneous recycling of plastic waste containing brominated flame retardants (BFRs) and metal oxides (printed circuit boards, automotive shredder residue, plating sludge, metallurgical dusts). In this work, a differential scanning calorimeter and laboratory-scale furnace were used to investigate the possibility and conditions of the bromination of ZnO by product of thermal decomposition of TBBPA. The formed solid, condensed and gaseous products were analyzed by X-ray diffraction analysis, electron probe microanalysis, inductively coupled plasma analysis, ion chromatography and gas chromatography coupled with mass spectrometry. Introduction Tetrabromobisphenol A (TBBPA) is the largest volume brominated flame retardant (BFR) in production today and is used in more than 70% of the world’s electronic and electric (E&E) appliances [1]. The growth in the production of E&E products and the fact they become obsolete so quickly cause significant problems in the safe disposal and recycling of the electrical and electric waste (E-waste) and other BFR-containing waste [2]. Among various treatment processes, thermal methods are most useful since they allow the recycling and recovery of both the organic and inorganic fractions of the waste. However, incineration of the BFR-containing wastes results in the emission of hazardous organobromine compounds, while the main portion of bromine released from decomposed BFRs is present in flue gas as hydrogen bromide (HBr) [3]. HBr, which is known to damage incineration systems, seems to be a very effective bromination agent for many metallic oxides present in waste. The concept of this study is to take advantage this of its property."

Jan 1, 2008

By Feng Liu, Bingji Yan, Zhiwen Shi, Hongwei Guo, Jianliang Zhang

During production of a large quantity of steel, slag is produced at the same time. This paper chooses blast furnace slag (BFS) as the main material for the research. The purpose of the research is to explore its optimal physicochemical properties and the use of BFS in building stone field. The paper elaborates the experimentation process of producing glass-ceramics and presents the results. The results show that SiO2 content in BFS and amount of Cr2O3 and Fe2O3 added as nucleating agents have certain effect on the properties of glass-ceramics. The results also show that the exothermic peak temperature of base glass is the lowest when adding 20% SiO2 to the BFS, and 2% Cr2O3 and 3% Fe2O3 as nucleating agents, which makes easy crystallization and optimal properties of the glass-ceramics.

Jan 1, 2015