Search Documents

By Luciano R. G. Santos

Keywords: biosorption, cadmium, copper, biomass, spent zeolite. The majority of the industrial activities produce some kind of solid wastes. In this work two industrial residues (spent zeolite and wood sawdust) were chemically modified to increase their heavy metals sorption capacities. Manilkara longifolia (a Brazilian plant known as parajú) sawdust was first treated with NaOH and modified with different citric acid concentrations (0.6-1.2 mol/L) at 120°C, for 90 min. Infrared spectroscopy confirmed the presence of carboxylate groups in the wood structure as result of their mixing. Similarly, spent zeolites were also submitted to a chemical treatment (NaOH) to remove carbon deposited during oil cracking and to recover its sorption capacity. Batch experiments carried out at ambient temperature showed that both materials present sorption capacity for copper and cadmium comparable to weak acid ion exchange resins. A maximum of 78 mg-Cd/g and 59.7 mg-Cu/g as well as 29.9 mg-Cd/g and 14.6 mg-Cu/g were observed for the sawdust and the zeolite, respectively. The results were modeled according to the Freundlich and Langmuir equilibrium isotherms and compared with results of other studies.

Jan 1, 2005

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct-to-Blister process design.

Jan 1, 2003

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003

By Yasuo Ojima

The mainstream of copper smelting processes in the world today is a combination of Outokumpu type Flash smelting and PS (Pierse Smith) converting process. Presently it can be estimated that about 50% of the worldwide copper production is produced by the Flash smelting process and 80% by the PS converting process. PS converting process due to its operational flexibility and despite its batch character of operation has been widely used in many smelters for more than 100 years. However, an environmental issue has been pointed out related to this process because of the difficulty of handling the fugitive gases. Recently several copper smelters in the world have been newly constructed and others have executed major modification and modernization, The continuous converting process has been applied in many of them instead of PS converting process. This paper compares PS to the emerging continuous converting process and makes a prospect of the future of the copper converting process.

Jan 1, 2003

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By A. F. Kaczmarek

Cerro Negro is an undeveloped ore body located at the Cerro Verde mine near Arequipa, Peru. The mineable reserve contains 70 Mt of oxide ore grading 0.532% copper. Mineralization is hosted in three distinct rock types: tourmaline breccia, crackle breccia and granodiorite. Rock type effects copper recovery and acid consumption. The paper describes Cyprus' testwork philosophy and the resulting four-phase metallurgical program used to define the commercial leaching parameters. Copper recovery and acid consumption were monitored as functions of crush size, heap height, irrigation rate and acidulation conditions. Single lift, on-off and permanent multi-lift heaps were considered. Leach cycle times were based on incremental copper extraction and acid consumption rates, with added constraints imposed by operational requirements. The optimum leach system involves an on-off pad using tertiary crushed ore acidulated with 20 kg/t acid and stacked to a height of 6.5 m. The active leach cycle is 82 days at an irrigation rate of 0.26 l/min/m2. Under these conditions copper recovery is expected to average 81% over the life of the mine.

Jan 1, 1999

By Asmo Vartiainen

Background of Direct-to-Blister Flash Smelting is discussed; especially slag chemistry relating to copper solubility, slag fluidity and impurity behavior. In December, 2000, Mini-pilot Flash Smelting test runs were carried out at Outokumpu Research Oy to produce blister copper from Chilean concentrate and white metal and from a mixture of them. Tested slag types were iron silicate slag, ferrous calcium silicate slag and calcium ferrite slag with different slag compositions and different concentrate/white metal ratios. The test runs were successful. The fluxing effect of copper oxide was clearly demonstrated and ferrous calcium silicate slags remained fluid on a very wide liquidus range. The distribution of arsenic between ferrous calcium silicate slag and blister copper is much higher than between iron silicate slag and blister copper. This successful test run with the new slag type offer new possibilities in Direct- to-Blister process design.

Jan 1, 2003

By Kazuya Koyama

We are studying the hydrometallurgical recycling process of indium from an Indium-Tin-Oxide(ITO) target. For this process, it is necessary to remove Sn(IV) ions from the aqueous hydrochloric acid solutions containing In(III). In this study, the removal of Sn(IV) ions by a potentiostatic electrolysis method was examined. The polarization measurements and potentiostatic electrolyses were carried out under a nitrogen atmosphere. In the Sn(IV) solution, current begins to rise at the cathode potential of -0.26 V vs. SHE, and increases with a reduction in the cathode potential. In the In(III) solution, current begins to rise at a cathode potential of -0.43 V vs. SHE. Metallic tin was electrodeposited without indium electrodeposition at the cathode potentials of -0.30 and -0.40V vs. SHE. More than 98% of the Sn(IV) was removed at the cathode potential of -0.40 V after the electrolysis for 3hrs. Both tin and indium were electrodeposited at the cathode potential of -0.50V vs. SHE.

Jan 1, 2006

By Juan Daniel Martínez, Janaina Accordi Junkes, Dachamir Hotza, Tatiana Pineda

"The rice husk combustion in a bubbling and atmospheric fluidized bed reactor was investigated. The results showed the technical viability of producing both heat and amorphous silica from a renewable energy source. This paper presents the characterization of rice husk ash (RHA) obtained under varying fluidization velocities (0.13-0.15 m/s) and rice husk feed (4.5-7.2 kg/h). Characterization techniques include X-ray fluorescence, X-ray diffraction, particle size distribution and scanning electron microscopy. For the employed range of fluidization velocities of rice husk feed no noticeable influence on the chemical composition of produced RHA was observed. After combustion, RHA containing ~93% amorphous silica and <3% unburned char was obtained. RHA primary particles presented sizes from 90 to 100 µm and a tendency for agglomeration in aqueous media. Thus, the potential of this type of reactors with respect to speed, continuity and self-sufficiency energy of the process was shown.IntroductionDue to the increase of the agroindustrial production, the concern with processing by-products, such as rice husk (RH), is growing. For a better material and energy use, allowing a cleaner production and a more maintainable development, RH can be used as renewable fuel in the production plant, for instance, in steam generators. The adequate combustion of RH generates hot gases with low levels of pollutants, as carbon monoxide and particulate material.RH is the protecting coating formed during the growth of the rice grain, composed by four structural layers.1 The main components of the husk are cellulose and hemicelulose (50%) besides lignine (26%) and organic components (4%), as oils and proteins. The remaining amount includes inorganic materials (SiO2, Al2O3, K2O, Na2O, MgO, CaO, Fe2O3, MnO, P2O5).1The rice husk ash (RHA) is the product of the termochemical transformation of RH. The conditions of the different conversion processes (pyrolysis, gasification and/or combustion) determine the physical-chemical characteristics of the final product. RHA corresponds to 14 to 25% RH, depending on the variety of the rice, climate and soil of the producing area.2-4 The main component of RHA, which is generated at moderate combustion temperatures, is amorphous silica (SiO2) in the range from 80 to 97%.4,5"

Jan 1, 2008

By Shadia J. Ikhmayies

"Tin oxide (SnU2) thin films of thicknesses in the range 100-600 nm were prepared on glass substrates by vacuum evaporation at ambient temperature. The films were characterized by transmittance measurements, X-ray diffraction (XRD), scanning electron microscope (SEM) observations and energy dispersion X-ray analysis (EDAX). It is found that the films have high transmittance and non sharp absorption edges. XRD diffractograms showed that the films are amorphous and the SEM micrographs showed that the surfaces are smooth, uniform and well covered with the material. The EDAX analysis showed that the films are deficient in oxygen. Indirect optical bandgap energy and Urbach tailing in the bandgap was observed, and the width of the tail, which is related with disorder and localized states, was estimated.IntroductionTin oxide is an n-type wide bandgap semiconducting material with a direct bandgap energy of 4 eV and an indirect bandgap of 2.6 eV [1], where inherent oxygen vacancies act as an n-type dopant [2], Tin oxide thin films have been used for transparent electrodes in photoelectric conversion devices namely amorphous silicon solar cells, liquid crystal displays, gas discharge displays, etc. [3]. Perfectly amorphous thin SnO2 films show good electrical response to reducing gases in air and could, hence, be applied to construct semiconductor gas sensors where the metal oxide films function as a monograin-eqivalent active layer [4]. Amorphous SnU2 can also be used in extended gate field-effect transistors (EGFET) as a pH sensor, where the sensitive part is made of the SnO2/Al structure. This device can be used to detect and to quantify any kind of substance that can produce or consume protons, like an enzymatic reaction, therefore showing a large range of applications as biosensors [5].There are different methods to prepare SnO2 films, such as atomic layer deposition (ALD) [6], reactive magnetron sputtering [7], chemical vapor deposition [8, 9], dip coating [10], spray pyrolysis (SP) [3, 11-14], and evaporation [8], The thermal evaporation method was chosen to produce SnO2 thin films in this work because deposition by this technique does not present any compositional problems. In addition, it is a low temperature technique, which increases the probability of producing amorphous films. To increase this probability, the films were deposited at ambient temperature."

Jan 1, 2012

By Pengfu Tan

In order to understand and control the formation of dioxins and furans in iron ore sinter plants and to possibly avoid expensive end-of-pipe removal stages, thermodynamic calculations on the stability of PCDD/Fs have been combined with sinter process modeling by means of kinetic simulations and computational fluid dynamics. Three thermodynamic databases of PCDD/Fs, derived using the Group Additivity approach and two computational molecular modeling methods, MNDO and PM3, respectively, combined with the SGTE database have been used to model the PCDDIF formation and the PCDD/F isomer distributions in iron ore sintering. The results show very similar conditions for the PCDD/F formation using the different databases. Concerning the isomer distributions of toxic PCDD/Fs, the calculated data derived from the MNDO method showed optimum agreement with measured values from industrial furnaces. The thermodynamic calculations also proved that the isomer distributions found in combustion processes are equilibrium values, while the concentration ratio of PCDDs and PCDFs in the wind boxes does not represent an equilibrium state. A CFD model of iron ore sintering was developed including the kinetics of 15 relevant chemical reactions with the aim of describing the temperature fields and the gas flow patterns in the sintering bed. On the basis of these information and experimental observations reported in the literature possible pathways for the PCDD/F formation in sinter plants have been identified: PCDD/Fs are formed in the critical temperature region of 250 to 450 °C below the combustion zone, are then carried downwards with the gas and condensed close to the bottom of the sinter bed. Transported to the discharge end with the solid mixture, they are again released into the gas phase when the flame front approaches the bottom. PCDD/Fs are also formed in the last wind boxes when the hot off-gases cool down and reach the critical temperature range. Consequently, methods to reduce the dioxin formation reactions are proposed including inhibitor addition to the sinter feed and off-gas quenching.

Jan 1, 2003

By Youn-Bae Kang

Evaporation mechanism of S from liquid Fe–C–S alloys at 1873 K was proposed by analyzing available experimental data. It has been known that increasing C content in liquid alloy increases activity coefficient of S ðfSÞ, and it could raise driving force for the evaporation reaction S = S(g). However, experimental data of the evaporation of S in the Fe–C–S alloys could not be accounted for only by considering the increases of fS. In the present study, formation of carbosulfides, CS(g) and CS2(g), was additionally taken into account in order to explain role of C for the accelerated S evaporation. Surface adsorption of S was also taken into account, which retards the evaporation rate of S. An evaporation model equation was formulated. It can be applied to calculate the evaporation rate of S over wider C content (from zero to its saturation to liquid alloy).

By H. Yin, T. Emi

"Advantages of gas/flux injection technology as materialized in the main stay unit processes for steelmaking are depicted covering hot metal pretreatment through secondary refining. Current status of micro-kinetic issues involved in the injection technology are reviewed including gas-in- metal, gas-in-slag, flux-in-metal, metal-in-flux and three-phase dispersion systems with reference to macro-kinetics. Key problems are briefly addressed to further develop injection technology for steelmaking processes.1. FROM PAST TO PRESENTApplication of gas injection to steel industry started in early 1950's when inert gas bubbling via stopper rod, lance, or porous refractory plug was practiced to make the temperature of steel melt in ladle uniform The gas bubbling in ladle was then extended to slightly removing hydrogen ti'om the steel melt tapped from Electric Arc Furnace (EAF) and Basic Open Hearth Furnace (BOH) when vacuum processing facilities were not popular. Later, oxygen gas injection via calorized steel pipe into molten steel bath in BOH Furnace was also put into operation to promote the decarburization to increase the productivity of the process. This line of development has been made in parallel with more profound processes, i.e, top blowing Basic Oxygen Furnace (BOF) for primary steelmaking and side blowing Argon Oxygen Oecarburization (AOD) vessel for decarburizing stainless steels.On the other hand, injection of fluxes into steel bath was first industrialized in Germany in 1960's, Primary objective was to desulfurize steel melt in ladle by injecting CaC2 or CaCrCaO mixture via lance under neutral slag cover with good success. Difficulties in injecting fluxes without clogging and rippling at a desired flux/gas ratio, and durability of injection lance were resolved in due time to bring forth many injection facilities to flourish for versatile refining operation. Top injection of fluxes from main oxygen lance to BOF was also industrialized as LDAC to promote early slag formation. A new process then emerged which injects oxygen gas and fluxes together through concentric annular tuyere, installed at the bottom of the BOE into steel melt. This process, developed in Germany [Oxygen Bottom Maxhutte (OBM)] and brought into maturity in USA (Q-BOP) and Japan in a large scale operation, became the predecessor of the combined blowing (top and bottom blown) BOF which dominates modern steelmaking."

Jan 1, 1996

By Ivan Imris

The common problem of new and conventional technology of copper production is the copper losses in the slags, which may be divided into mechanical and physico-chemical losses. In the first group can be included particles of mechanically entrained or floated unsedimented matte particles which coexist with slag. On the other hand, the physico-chemical losses are caused by solubility of copper in the slag in the form of sulphide and oxide. The copper losses in the slags from different processes has been predicted by calculation from thermodynamic data and compared with those determined by microscopic examination and quantitative electron microprobe analysis. Depending on the forms of copper losses in the slag the reduction of copper losses in the slag or the slag cleaning process could be suggested.

Jan 1, 2003

By Mitsutaka Hino

The contents of gangue minerals, such as A1203, P205, crystalline water and so forth in the iron ore imported to Japan tend to increase year by year, Though the increments of such gangue contents are approximately 0.1-0.2 mass%, some problems for the blast furnace operation in ironmaking process have already been reported, In order to clarify the mechanism of harmful effect caused by the small increment of gangue minerals, mainly A1203, on the blast furnace operation, the dripping behavior of FetO-CaO-SiO2-AI2O3-MgO slag from the iron funnel, which simulated the micro-porosity in sinter ore, has been observed with the wide range of basicity, Al2O3, FetO and Mgo contents. The effect of MgO on the dripping behavior of slag has been summarized in this paper, It was found that the addition of 2mass% MgO resulted in large increase of hold-up on the most of the conditions. When FetO content was less than 20mass% and the basicity was lower than 0.8, MgO lowered the hold-up even if the slag contained 10mass% Al2O3. Every slag hold-up showed the minimum at the basicity of less than unity on the conditions of constant FetO and A1203 contents. This trend became remarkable when the slag contained 2 mass% MgO.

Jan 1, 2003

By D. Majuste

This paper describes an experimental approach to evaluate the effect of organic impurities or even additives on metal electrowinning and product quality. In addition to electrowinning tests and electrochemical measurements, the approach includes organic analysis by Fourier Transform Infrared spectroscopy and gas chromatography; video monitoring of the reaction interface; and product characterization by using scanning electron microscopy, crystallographic texture and bending tests. The mechanical behavior of metal cathodes was assessed with a customized bending device that is able to bend the cathodes up to angles similar to that of the stripping machine. In this work, the effect of a potential organic impurity, lubricating oil, on the production of electrolytic zinc is taken as a case study. The findings of the investigation allowed a better understanding on the role of this organic on energy consumption and product quality and a qualitative prediction for the behavior of Zn cathodes during the stripping operation. Simple control and optimization procedures resulted in significant energy savings.

By Yongzhong Xiao, Tiejun Chun, Jian Pan, Zhen He, Deqing Zhu

"In this paper, the reduction kinetics of low grade hematite ore was calculated. Mineralogy shows that the ROM (run of mine) ore is of low grade hematite ore type, assaying 27.2 wt% Fetotal and with main valuable minerals of hematite. The reduction kinetics shows that the reduction reaction rates of pellets with additive and without additive are all controlled by diffusion through the product layer. The calculated apparent activation energy of pellets with 12 wt% complex additive is 8.55 KJ/mol, dropping 62.23% compared to that of pellets without additive.IntroductionWith the rapid development of iron and steel industry in China, there has been a soaring demand for iron ores in the past decade. The imports of iron ores have increased from 148 million ton in 2003 to 620 million ton in 2010[1]. Therefore, large quantities of low grade iron resources are necessary to utilize in China at the moment. During the past years, extensive research has been carried out on the low grade hematite ores [2-6], such as reverse floatation, gravity separation, high-gradient magnetic separation and direct reduction-magnetic separation. Direct reduction-magnetic separation is an innovation way to treat the low grade hematite [7]. However, the research of reduction kinetics of low grade hematite is few. Some research about the reduction kinetics of reducing iron oxides by CO was studied [8]. The results indicated that the apparent activation energy is 8.0-28 KJ/mol when the reducing reaction is controlled by internal diffusion. The apparent activation energy is 50-75 KJ/mol when the reducing reaction is controlled by chemical reaction. In this paper, the reduction kinetics of pellets was also been studied."

Jan 1, 2012

By Denise Nascimento, Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Renan Carreiro, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"Natural fibers obtained from plants have increasingly been used as reinforcement of polymeric composites in engineering applications. This is the case of the fiber extracted from the piassava palm tree, a native of the southeast region of South America, which for a long time has been used in simple items like brooms and brushes. Recently it was reported that the tensile strength of the piassava fiber varied inversely with the equivalent diameter. Following that previous work, the elastic modulus and the density dependence on the diameter of stiffer piassava fibers of the Attalea fiinifera species was investigated. Precise measurements with a profile projector and Weibull analysis of the experimental results indicated that both the elastic modulus and the density of piassava fibers also follow an inverse correlation with the diameter. Scanning electron microscopy observations of the microstructure and fracture surface showed that defects and participation of microfibrils are responsible for this correlation.IntroductionIn the past decades, both the increase in the price of the petroleum and climate changes due to greenhouse gas emissions are motivating the use of renewable and low cost natural materials as a substitute for energy intensive and CO2 contributor synthetic materials [1]. A typical case is that of natural cellulose-based fibers extracted from cultivated plants in comparison to glass fibers, which are extensively used for composite reinforcement. In fact, these natural lignocellulosic fibers are increasingly being investigated [2-6] as possible reinforcements of polymeric composites, and in some cases, successfully replacing glass fiber composites in engineering applications [7]. The automobile industry has remarkable examples of lignocellulosic fiber composite substitutions [8-10]. Not only do some of these fibers display specific mechanical properties comparable to glass fibers but their composites also contribute to lower equipment wear and better finishing of molded components [6]."

Jan 1, 2012

By J. R. Goode

Up to one half of neodymium and praseodymium production, key ingredients in permanent magnets, is produced illegally. About 60% of cobalt production, critical in lithium-ion batteries and other applications, comes from central African states, and much of it is produced illegally. Tantalum, important in modern electronics, is also primarily sourced from central Africa and, again, much of it illegally. Illegal mineral production, as exemplified here, is often used to fund armed conflict. Furthermore, it is typically conducted with scant regard for human rights and environmental protection. It also leads to depressed prices which in turn limits the possibility of legitimate producers entering the market. Systems of traceability and provenance, along with cooperative supply chain participants can limit the production of illegitimate material and thereby improve conditions in the countries of origin and reduce downward pressure on prices.

By Jose Hector Figueroa P.

Mexicana de Cananea, S.A de C.V. is a major copper producer mining a large deposit of the disseminated porphyry type considered one of the largest copper resources of the world with 2.7 billion tons of 0.60% copper for the mill plus 4.1 billion tons of averaging 0.26% copper for leaching. Mining of low grade sulfide leach ore, has been an important part of the overall production of the open pit mine which started in 1944. Before this time all the mining in Cananea was by underground methods. The leaching process in Cananea began on the 1920&apos;s with in situ operations in the underground mine and small dumps up to the 1950&apos;s. Large scale leaching operations began in 1960 and the copper solutions produced were treated in precipitation plants until 1,980 when the first SX/EW Plant was put in operation in Cananea. Leaching action is essentially ferric-bacterial, with no fiesh acid added to the leaching solutions. Traditionally, 5540% copper extraction is recovered fiom ROM, 70- 120 meter high leach dumps in 80 months of leaching. Cananea has successfully improved copper recoveries by implementing several actions that include: 1. Stripping of old dumps. 2. Leaching of old dumps through slotted casing. 3. Crushing conveying leach ore to minus 8 inch and stacking it in 30 meter lifts. As result of these actions, copper recovery has been increased&apos; to about 70% of total copper with actions 1 and 2 and up to 85% in half the time by crushing-conveying the leach ore, based on the same solubility index of the run-of-mine ore. This paper describes the above actions that were implemented to enhance the leaching recoveries from. sulfide leach dumps and the economics of such actions.

Jan 1, 1999