Search Documents

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By Martin J. Hansel, Jan Bäckström

Starting from historic perspectives on converting at the Rönnskär Smelter, the continuous developments of refractory practice is described. In the development the joint efforts of operators and suppliers of refractory have lead to significant achievements. This paper comprises the development of the converting process and the refractory lining as well as future prospects regarding operation and refractory lining design, especially in the face of equipment and raw material availability. 81

Jan 1, 2009

By Jared Ball, Benjamin Hogg

There are over 100 process parameters that can be monitored during a single Peirce-Smith (PS) converter batch operation. To support a consistent operation it is important to select the correct Key Performance Indicators (KPI’s) to monitor. They should be strategically chosen to drive the desired behaviour with enough flexibility to endure process variations. At the Xstrata Copper Smelter in Mount Isa most of the PS converter operators have very little experience and are often lacking in the appropriate education or training to properly understand the process. For this reason 10 simple KPI’s were chosen that could be easily comprehended and monitored by all smelter personnel. KPI compliance has been supported by relevant project work in the converter area. Charge sequence trials have been performed in an effort to reduce splash and optimise activity time. The online measurement of full and empty ladle weights has enabled an immediate indication of skull size, skim/slag carryover, and metal loss.

Jan 1, 2009

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the influence of Fe+2 initial concentrations in the bioleaching of copper from printed circuit board using Acidithiobacillus ferrooxidans-LR. Printed circuit boards were collected from obsolete computers and mechanically processed through size reduction followed by magnetic separation. The bacteria Acidithiobacillus ferrooxidans-LR were grown and adapted in presence of printed circuit boards. A shake flask study was carried out on the printed circuit boards samples (non-magnetic fraction) using a rotary shaker under the following fixed conditions (185 rpm, 30°C). The bioleaching efficiency was evaluated by comparison between the concentration in the initial sample and in the leached liquor, pH of the medium and concentration of ferrous iron produced. Inductively coupled plasma optical emission spectrometry (1CP-OES) was used to determine the metals concentration. The results showed that Acidithiobacillus ferrooxidans-LR leached 63% copper from printed circuit boards using supplemented medium with Fe+2.IntroductionThe waste of electric and electronic equipment is generated by discarding of equipment such as obsolete computers and cell phones which is stimulated by the technology innovations and it has been growing each year. Because of the amount that has been accumulated it has become a prominent environmental problem but also can be a source of valuable materials, such precious and base metals [1,2] The printed circuit boards are found in almost all electric and electronic equipment being composed of polymers, ceramics and metals and can be an alternative source to recover base and precious metals. The precious metals are used in the printed circuit boards to protect against oxidation and base metals because of its conducting properties [3]. The heterogeneous composition of printed circuit board is a limiting factor in the recycling processes and the metals concentrations also range."

Jan 1, 2011

By Nan Zhang, Lei Zhang, Gai-feng Xue, Lina Wang, Pu Liu

"A novel ß-diketone modified silica gel was synthesized by a simple reaction. The prepared material was characterized by diffuse reflectance FTIR spectroscopy and it was used for the adsorption of heave metal ions in the industrial waste water. The main parameters affecting the sorption of heavy metal ions, including pH, water flow rate, and elution, have been investigated in detail. Under the optimized operating conditions, most of the targeted heavy metal ions could be removed. The material could be simply regenerated by hydrochloric acid solution. The method is rapid, selective, economic and applicable to the removal of heavy metal ions from industrial waste water.IntroductionToxic organic pollutants and heavy metals ions mainly from industrial activities such as plating, metallurgy and dyeing industries, are a threat to human health and the surrounding environment, because of their toxicity and persistence after being released into the natural environment [1]. These pollutants must be removed or degraded to an acceptable level, before being discharged to the receiving waters. Therefore, detection and determination of heavy metal ions in industrial waste water is very important.Inductively coupled plasma optical emission spectrometry (ICP-OES) is the most used technique for the determination of heavy metal ions because of its capability for rapid multi-element detection over a wide concentration range and with relatively low detection limits. Compared to other techniques such as neutron activation analysis (NAA), X-ray fluorescence spectrometry (XRF) and inductively coupled plasma mass spectrometry (ICP-MS), ICP-OES has the above advantages. Some constituents in industrial waters, such as organic compounds and inorganic salts, may cause matrix effects. In order to achieve accurate and reliable results, an efficient preconcentration of heavy metal ions and their separation from the matrix are usually required."

Jan 1, 2012

By J. V. Happ

The investigation reported in this paper was prompted by the belief that vacuum processing of copper mattes could provide significant advancement to present-day copper smelting and converting technology. Specifically, vacuum distillation of copper mattes in a unit such as the R.H. vessel used in vacuum degassing of steel, can lead to improvements in: converter flue-gas-cleaning system, purity of acid (or liquid SO2), aisle hygiene, purity of electrorefined copper and smelter flexibility. In the study conducted, removal of Volatile impurities (arsenic, antimony, bismuth, lead and zinc) from liquid mattes, by vacuum distillation in a laboratory-scale equipment was performed. The conditions investigated covered a temperature range of 1123-1223K, absolute pressure of 6.5-0.5kPa (50 - 3 mm Hg) and with bleed gas consisting either of pure oxygen or argon. Six matte samples (four U.S. and two foreign) were tested. Under the "best" conditions arsenic and antimony were reduced to << 0.01% in the product matte. The removal of bismuth, lead and zinc was variable and appeared to be influenced by the matte composition of the sample. As might be expected, the rates of distillation of the various species were increased at higher temperatures and lower absolute pressures. The influence of a small flow rate of gas (02 or Ar) over the melt did not have a signifi¬cant influence on the extent of impurity removal. The magnetite content of the matte was reduced by up to 30% during vacuum treatment and was favored by a low partial pressure of oxygen over the melt. Substantial amounts of sulfur were also evaporated and an, overall increase in copper grade of the matte was realized. The paper concludes with an evaluation of industrial aspects of the process as applied to conventional smelters.

Jan 1, 1983

By Carlos Eduardo Gomes de Souza, Luis G. S. Sobral, Paulo A. Medeiros da Silva, Selma G. F. Leite, Renata de B. Lima

"The use of mixed cultures of acidophilus microorganisms that act in different temperature ranges, aims at speeding up the digestion of chalcopyrite, highly refractory sulphide mineral, the major mineral in the flotation concentrate of Caraíba Mining Co., with an attractive processing cost. The concentrate under consideration contains mainly chalcopyrite (CuFeS2) and bornite (Cu5FeS4) with contents of, approximately, 70 and 30%, respectively. It was observed in this study, the performance of consortium of mesophiles, moderate and extreme thermophile microorganisms, in the oxidation of the aforementioned sulphides minerals, evaluating operational parameters such as pH of the leaching solution, the reaction temperature and redox potential, with consequent extraction of 80% of the concentrate copper content within 60 days of bioleaching. Such high copper extraction was achieved in column bioleaching tests.INTRODUCTIONThe solubilization of metals by the application of microorganisms from the mineral ores and the subsequent recovery of metals from solution are referred to as bioleaching (Rohwerder, T et al, 2003). This is an economical method for the recovery of metals from minerals; especially lowgrade ores, overburden, and waste from current mining operations which requires moderate capital investment with operating cost (Watling, 2006).Furthermore, bioleaching is generally more environmentally friendly than conventional metal recovery processes such as concentration and smelting. Those physicochemical metal extraction processes generate sulphur dioxide, a toxic emission that is increasingly the target of regulatory legislation (Stott et al., 2000; Olson et al., 2003). Bioleaching of chalcopyrite is the key industry target. The main problem hindering commercial application of chalcopyrite bioleaching is the slow dissolution rate (Fu et al, 2008).Dissolution of acid-soluble sulphide minerals such as sphalerite, and to a lesser extent chalcopyrite, occurs by a combination of ferric iron and proton attack via the polysulphide pathway (Rohwerder et al., 2003)."

Jan 1, 2008

By Magnus Ek, Peter Olsson

The Rönnskär Smelter has been faithful to Peirce Smith Converting during its 79 years of existence. Though a visitor to our smelter museum will easily find out that a lot has happened since the beginning – and development continues. In this paper an up-date on Converting and Casting at the Rönnskär Smelter is presented. Recent developments include an investment into converter process gas handling, but also day-to-day operational aspects such as converter aisle productivity and flexibility, but also minimal EH&S impact. 127

Jan 1, 2009

By S. Saptharishi

Selenium, which is a 6A group element of the periodic table, constitutes about 7x10-5 % of the earth?s crust. Even though selenium is a dispersed element with respect to its commercial exploitation, it is capable of forming number of minerals and nearly forty selenium minerals have been identified, out of which the copper ores are the richest sources of selenium. Electronics industries and glass industries are the major consumers of selenium, while pharma grade selenium used as micronutrient for humans and animals. Various methods have been developed to recover selenium as a by-product from copper anode slime during copper refining. Selenium being amphoteric in nature, it is soluble in both acid and alkali. While acid roast process is widely used, considerable work has been carried out in Russia for recovering selenium through alkali route. This paper enlightens the process developed at Central Research and Development Laboratory, for recovering selenium from decopperised slime through alkali pressure leaching. The decopperised slime is pressure leached with alkali under oxidizing conditions by which almost all the selenium present is converted to alkali selenate, which is easily separable from the rest of the decopperised slime. The solution so obtained is neutralized, during which, most of the impurities are precipitated out. Then selenium is precipitated in its elemental form upon purging sulphur-di-oxide under warm acidic medium. The purity of the selenium obtained by this process is higher than that of the selenium from acid roast process. Moreover selenium can be crystallized as sodium selenate and it can be marketed. The acidic content of the effluent is recovered and it is recycled back to the process. The sodium content of the effluent is converted into high purity sodium sulphate, which is marketable. The hazardous waste containing arsenic is precipitated as its sulphide and can be disposed off as landfill.

Jan 1, 2006

By R. J. Dippenaar, W. H. Van Niekerk

"An injectable lime-based desulphurization reagent for the treatment of liquid iron was developed. Firstly, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na20 to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. Subsequently, pilot plant and full scale industrial injection trials were conducted. It was found that lime-based slags, containing Na20 and CaF2, are able to desulphurize liquid iron efficiently. By the injection of a lime based reagent consisting of 60% lime, 25% soda ash and 15% fluorspar at a rate of 7 kg reagent/ton hot metal, the sulphur level in the metal (115kg) was reduced from 0,07% to 0,01 % within 5 minutes. The lime-based reagent developed in this study was successfully injected, both from a metallurgical and from a pneumatic point of view, on an industrial scale. The mathematical model utilised in this study, can be used successfully to predict the course and extent of desulphurization by lime-based slags. IntroductionMainly due to environmental difficulties encountered with pure soda ash, dry slag formation with CaC2 and high cost when Mg are used as desulphurizers, much incentive exists for the development of an inexpensive, environmentally friendlier desulphurization reagent. As a first step in the development of such a reagent, selected lime based slags containing small quantities of CaF2 to increase fluidity, and Na2O to increase the basicity, have been evaluated on laboratory scale from a thermodynamic point of view. This was followed by pilot plant injection experiments in which the kinetics of the relevant desulphurization reactions were evaluated. Finally, full scale industrial trials were conducted. All three phases of the investigation will be discussed with the major emphasis being placed on the kinetic study."

Jan 1, 1996

By De-qing Zhu, Jian Pan, Tie-jun Chun, Dong Chen, Yu Cui

"A study of processing pyrite cinder and metallurgical slag using “one step” technology in strand grate - rotary kiln is presented, which aims to efficiently recover the valuable metals of iron, lead, zinc and copper. The effect of chloridizing roasting parameters including roasting time and temperature on the removal rates of nonferrous metals was investigated. It is shown that copper and zinc are difficult to remove and lead is removed more easily. The preheated pellets were reduced in a rotary kiln, where zinc and lead can be removed easily and high iron grade and good metallurgical performance prereduced pellets can be obtained. Furthermore, the chlorination and the reduction mechanisms of copper, lead and zinc are discussed. It is revealed that the phases of copper, lead and zinc in slag are complex and ferrite and silicate of metals are difficult to remove.IntroductionAs two kinds of significant secondary resources, metallurgical slag and pyrite cinder contain not only abundant iron but also considerable copper, lead, zinc and so on. Several tens of millions of tons of metallurgical slag and pyrite cinder are discharged in nonferrous metal and chemical industries annually in China [1, 2]. In addition, the accumulated waste slag in storage is more than one hundred million tons, which not only occupies much land but also pollutes the environment [3]. However, because the metallurgical slag and pyrite cinder are treated by high temperature processing, the properties are distinctly different from the properties of natural ores, and iron is in close association with copper, lead and zinc. So, metallurgical slag and pyrite cinder are difficult to efficiently utilize and only a small amount is used as additives in cement, paving, brickmaking and auxiliary additives [4-7]."

Jan 1, 2011

By Hiroshi Ono

"By newly developed ICP method, trace amounts of As(III), As(V) .,Sb(III) and Sb(V) were precisely determined within accuracy of sub ng/ml. As(III) and Sb(III) were separated from As(V) and Sb(V) by extracting into ·xylene as diethyldithiocarbamate complexes using diethylammonium diethyldithiocarbamate (DDDC), and then back-extracted into nitric acid for a quantitative determiruition by ICP-AES equipped with hydridegeneration system The recoveries of As(III) and Sb(III) were satisfactory throughout the extraction with 0.04mol/l DDDC in xylene from lmol/l hydrochloric acid solution and the back-extraction with 7 mol/l nitric acid. As(V) and Sb(V) were reduced to As(III) and Sb(III) by ascorbic acid and potassium iodide, and their quantities were determined as mentioned above. The detection limits were found to be 0.58ng/ml for As(III), 0.63ng/ml for Sb(III) using 50ml of a sample. The proposed method was applied to analysis of the real sample.Introduction In drain, arsenic(AS) concentration is prescribed below 0.lmg/l, so As must be removed. As is existed at .the form of As(III) or As(V) in solution. For t1Jeir difference of chemic;µ property, it is not easy to remove As in solution. So it is an urgent necessity to develop for determining concentration of As(III) and As(V). Antimony( Sb) has resemblance .chemical property to As. So Sb was experimented the same as As.The separation and determination of As(III) and As(V) have been carried out using several methods, such as ICP after copreclpitating separation, HPLC, direct hydride generation atomic absorption. However these methods have some problems. One of main problems is that HPLC and direct hydride generation atomic absorption methods are influenced by coexisting elements."

Jan 1, 2000

By K. Morsi, S. K. Kassegne, A. El-Desouky, K. S. Moon

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based fabrication of macro, micro and possibly nano-scale features and shapes. This new and unique process enables selective sintering of powders by localizing electrically activated sintering conditions through a stationary or moving electrically conducting tip. We present preliminary experimental results on the effect of tip size in the CA TS process as well as the effect of initial powder particle size on the sintering behavior of nickel powder.IntroductionSpark Plasma Sintering (SPS) has been the center of attention of numerous researchers due its noticeable advantages over conventional sintering techniques such as rapid heating rates, lower sintering temperature and shorter holding times. Research on SPS has been applied on a wide variety of materials such as pure metals [ 1], ceramics [2], composites [3], nano-materials [ 4], biomaterials [ 5], shape memory alloys [ 6] and many other material systems. However, it has been mostly limited to bulk materials with simple shapes with a few exceptions ofresearch efforts where the effect of electric current was combined with metal forming processes such as spark plasma extrusion [7,8] and electric rolling of powders[9]. In this paper a novel process (Current-Activated Tip-Based Sintering (CATS)) is discussed where electric current and pressure are applied simultaneously through a small conducting tip (stationary or moving) over a conducting powder compact. This process has the potential advantages of sintering complex geometries with minimum energy requirements as unconventionally high current densities can be achieved due to the small contact area between the tip and the powder compact. Furthermore, by controlling the tip size, it can be possible to sinter features on the macro-, micro- and even nanoscales."

Jan 1, 2011

By Yeliz Demiraya, Onuralp Yucelb

"Production of strontium metal from its oxide was studied under the pressure of 1-5 mbar by methalothermic process. SrO with 99 % purity was used in the experiments. Effects of Al powder addition (100, 200, 300 % of stoichiometric ratio) and time were investigated on recovering of metallic strontium. Effects of BaO addition (100 %, 200 %, 300 %) was also investigated. The final residues were examined for their chemical composition. XRD, AAS and Flame Photometer were used for chemical analysis. More than 96 % of strontium metal recovery can be obtained.IntroductionStrontium is an element which is used in many advanced technology applications. Barium strontium titanat, strontium bismuth titanat, and strontium bismuth tantalat thin films are promising materials in ferroelectric and Schottky-based microelectronics technologies, especially for memory applications. Physical vapor deposition (PVD) techniques as magnetron sputtering, thermal evaporation and molecular beam epitaxy (MBE) are the most widely used methods for growth of these thin films [1-3]. In these techniques high-purity of Sr metal is used as evaporation sources and sputtering targets. Furthermore, metallic strontium is used as a ""getter"" in electron tubes, and as an alloying elements in aluminum alloys [4].The most used Sr compound is SrCO3 and widespread process used in production of SrCO3 is the hydrometallurgical carbonation of celestite. Although there are considerable amount of Selestite reserves, SrCO3 and strontinum metal are not being produced in Turkey, yet [5].Concentrated celestite (SrSO4) is conversed to SrCO3 in carbonate media. Black ash and direct conversion processes are currently used methods. There are many satisfactory studies about hydrometallurgical carbonation of celestite and decomposition of SrCO3 [6, 7]. Since strontium metal is produced from it’s oxide (SrO), SrCO3 needs to be decomposed to SrO."

Jan 1, 2011

By Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"It has been demonstrated that metallic-bearing minerals are physically liberated from host rock when exposed to microwave (MW) energy. The metallic minerals are iron sulfides and spinel oxide minerals contained in peridotite rock. Experimental evidence has shown ore particles readily couple with MW energy at 2.45 GHz, 1000 W resulting in rapid heating. Thermal stresses are generated by highly absorbing metallic-bearing minerals resulting in cracking and embrittlement of ore particles that assists in crushing and grinding processes. The liberated metallic-bearing minerals are shown to report to coarser size fractions as a result of MW exposure.IntroductionComminution of ore material during beneficiation is a large energy expenditure for the mineral processing industry. Crushing and grinding operations alone consume 50-70% amount of energy used in mineral processing [1]. Size reduction becomes increasingly difficult with decreasing particle size making grinding the most energy-intensive step of comminution. The aim of comminution is to maximize liberation of economically valuable minerals from the host rock [2]. Overall, the less material that needs to be handled, then grinded, to create a useful product for hydro/pyro metallurgical processes will achieve the greatest reduction of energy.Much of the scientific interest for use of microwave (MW) energy in mineral processing has been for improved hydro/pyro metallurgical techniques [3-6]. Early authors have employed MW energy for improved grinding of ore particles but most conclude the energy savings do not justify the energy input [7-9]. The effectiveness of MW assisted grinding is dependent on the ore mineralogy and the absorptive properties of minerals contained within it. Ore containing magnetic minerals should prove successful with MW assisted breakage from highly absorptive properties."

Jan 1, 2012

By Jian Li, S. Penttila, W. Zheng

"Materials selection for Gen IV supercritical water reactor in-core components faces major challenges due to severe operating condition. Beside high-temperature mechanical properties, SCC and general corrosion resistance of commercially available materials are also major focuses in recent research. Recent reports suggest that certain types of surface modifications are beneficial to SCW corrosion resistance. In this study, the effects of surface modifications are investigated, and possible mechanisms for improved corrosion performance are discussed.IntroductionThe current Canadian pressure-tube supercritical water reactor (SCW) design specifies a core outlet temperature of 625°C under 25 MPa of pressure, with peak cladding temperature as high as 850°C. Challenges in materials selection include high-temperature mechanical properties, corrosion resistance, SCC resistance and radiation damage. Most of the SCW corrosion test results available are below 730°C. Early work by Allen [1] summarized the corrosion resistance of alloy groups including Ni-based super alloys, stainless and ferritic/matensitic (F/M) steels that can potentially be used for SCW reactors. F/M steels can only be used at low temperature sites (e.g. down stream piping). At 500°C and 25 MPa, F/M steels develop a thick but mechanically stable oxide layer. However, the long term stability of the surface oxide layer is largely unknown. Ni-based alloys appear to form very thin surface oxide, however pitting was observed in the vicinity of some intermetallic precipitates [2-5], and dissolution of major alloying components could pose significant problems for down stream piping [6]. In addition, concerns of Helium formation due to Ni transmutation prevented this alloy group to be used as fuel cladding. The corrosion resistant austenitic stainless steels (e.g. 316L) are found to be susceptible to localized corrosion such as pitting, intergranular attack and stress corrosion cracking (SCC) [7]."

Jan 1, 2012

By Chenhui Liu, Ka-ma Huang, Hong-ying Xia, Bingguo Liu, Hua Chen, Jinhui Peng, Libo Zhang

"The rising popularity of microwave heating in mineral processing has fuelled the need for knowledge concerning dielectric properties of minerals. Dielectric property and microwave absorption property of anthracite were measured over a temperature range of 20-100°C at 2.45GHz by using an open-ended coaxial sensor measurement system. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of anthracite are highly dependent on temperature and frequency. At frequency of 2.45GHz frequency used in microwave metallurgy, anthracite is suitable for reducing agent to achieve fast elevation of temperature then returning to original state. The research will be helpful in explaining the thermal running of microwave dielectric heating the anthracite.IntroductionThe application of microwave heating in minerals processing and treatment has recently attracted great interest from the metallurgical industry. Compared with conventional heating methods, the advantages of microwave heating include rapid and selective heating, uniform distribution, high efficiency, fast on and off switching as well as flexible and modular design[l-3]. As a result of these advantages, microwave heating has been applied in a variety of mineral processing and extractive metallurgy, such as microwave-assisted ore grinding, microwave heating for carbothermic reduction and acid leaching of ilmenite ore, microwave drying, microwave-assisted roasting and smelting of sulfide concentrate, microwave-assisted spent carbon regeneration and microwave-assisted waste management [ 4-6]. Though the application of microwave heating in the metallurgical industry is promising, further studies on the interaction between microwave radiation and minerals and its effects are highly desired to develop innovative techniques for minerals processing and ore treatment using microwave heating [7]."

Jan 1, 2013

By Artur Camposo, Rômulo. L. Loiola, Frederico M. Margem

"The growing interest for natural materials as an environmentally friendly alternative for the substitution of energy intensive and non-sustainable synthetic materials, has motivated the use of lignocellulosic fibers as reinforcement of biocomposites. The sisal fiber, a relatively unknown lignocellulosic fiber with potential for composite reinforcement, still needs to characterize for possible engineer applications. Therefore, the present work analyzed the sisal fiber by means of Fourier Transform Infra-red (FTIR) spectroscopy. The sisal fiber FTIR spectrum revealed main absorption bands typical of any lignocellulosic fiber. However, some specific bands as well as bands broadening and intensity suggested particular activities for functional molecular groups in the sisal fiber.IntroductionIn recent decades, environmental issues related to worldwide pollution and climate changes, mainly the global warming, are motivating new paradigms for the development of our society. Among these, the use of natural materials in substitution for non-sustainable synthetic materials, obtained from non-renewable ores and petroleum, is increasingly being considered. In particular, natural fibers extracted from plants are, in this 21st century, experiencing a surge as composite reinforcement [1-11 ], following their replacement by synthetic fibers, specially the glass fiber, during the second half of the 20th century [1-2-8].In addition to environmental benefits [12-13] the lignocellulosic fibers present economical advantages, such as worldwide abundance and comparatively low costs as well as some technical properties associated with flexibility and toughness[ll], which contribute to the performance of automobile components fabricated with natural fibers composites[14-16].Among the less common lignocellulosic fibers that only recently have been investigated[l 7], the fibers extracted from the stem of the sisal plant, shows in Fig 1, reveals a potential for polymer composite reinforcement."

Jan 1, 2013

By W. Y. Kim, K. H. Song, K. Nakata

"The present study was carried out to evaluate the mechanical properties of friction stir welded Inconel 600/SS 400 lap joints. In this process, friction stir welding (FSW) was performed at a tool rotation speed of 200 rpm and welding speed of 100 mm1min, and argon gas was utilized to prevent surface oxidation during the welding. Application of FSW notably decreases the grain size of Inconel 600 alloy from 20 µm in the base material to 8 ~ in the stir zone. However, the grain size of SS 400 in the weld zone was slightly coarsened, when compared to the base material. Also, the hooking in the advancing side and the intermetal1ic compounds (M7C3) in the weld interface between Incone1 600 and SS 400 were well formed. These intermetallic compounds and hooking were effective to increase in mechanical properties such as tensile and peel strengths.IntroductionFriction stir welding (FSW), applicable welding process at solid state, has several advantages in defect suppression such as blow hole, segregation and cracking which mainly occurs in fusion welding [1, 2]. Notable grain refinement in the stir zone due to FSW can expect the outstanding increase in mechanical properties of the welds. In constructing the chemical and power plants, Ni base superal10ys have been used in many parts, moreover, fusion welding as construct method, such as gas tungsten arc welding, electron beam welding and laser welding, has been mainly used [3-5]. However, fusion welding has a limit in an increase in chemical and mechanical properties in the welds. Lately, Ni base superalloys to which FSW applied have been reported with notable enhancement in mechanical properties, which resulted from refined grains in the welds [6-10]. These researches showed the possibility in applying the FSW, directly."

Jan 1, 2012

By Yotamu Stephen Rainford Hara

"The study focuses on the reduction mechanisms of copper, cobalt and iron during carbothermic reduction of copper-cobalt mineral sulphide concentrates in the presence of lime, in the temperature range of 1073K and 1273K. We have used three types of mineral concentrates which were derived from froth flotation from the Copperbelt region in Zambia. The reduction mechanisms were studied using thermogravimetric analysis in which selected reactions were stopped at different times for characterising the reaction mechanism using optical microscopy, XRD and SEM-EDX analyses. Using SEM-EDX analysis, we have analysed in details the stages of metallic phase formation during reduction process. Metallic cobalt and iron were embedded into copper, thereby permitting magnetic separation of the reduced metals even though copper is diamagnetic. Methods of preferential reduction of metal values were investigated by analysing the metallic phase formation.IntroductionIn conventional smelting or converting of copper sulphide minerals, metallic copper forms by giving off S02 gas on. Although in terms of overall energy balance the selective oxidation for metal production has major advantages, the process suffers from drawbacks in smelting complex concentrates containing copper, cobalt and iron sulphides minerals and these are: (i) cobalt and iron are oxidised, and consequently cobalt is lost into the slag phase. (ii) The volume of S02 gas produced is in low concentrations, which is insufficient for extracting sulphur or manufacturing sulphuric acid. The release of dilute S02 causes serious environmental pollution. The major cause for the loss of cobalt and iron into the slag, is due to that fact that the oxides of these metals are more stable than their sulphides. Since cobalt and copper are more valuable than iron, reducing conditions are required in a separate slag treatment reactor using electric arc melting for recovering the lost metal oxides from slag. This energy-intensive step makes metal making expensive.During chemical beneficiation of mineral sulphides (Cu2S, CoS, FeS) in the presence oflime (CaO), two types of equilibrium conditions may be set up either by forming CaS under reducing conditions, or by stabilizing CaS04 under oxidising conditions [l]. By comparison in the presence of carbon, CaS and metallic phases form, enabling the recovery of metals from sulphide minerals, which have been investigated by a number of authors [2-9]. During reduction of metal sulphide in the presence of lime and with carbon, it has been proven that the overall reaction le proceeds via two main steps: [5, 8, 9] (i) the anion exchange reaction between metal sulphides (MS) and CaO as shown in equation la, followed by (ii) the reduction of metal oxide (MO) via reaction lb."

Jan 1, 2013