Search Documents

By Huanyu Zhang, Quanqiang Ma, Huiqing Tang

Improvement of the coke quality for blast furnace (BF) iron making by hydrothermal oxidation treatment on coke quality was investigated. Results show that, under subcritical condition, sulfur removal rate is 15% and the weight loss is 3%; under supercritical condition, both sulfur removal rate and mass loss rate increase with the increase of H2O2 concentration. In the experimental conditions, sulfur removal rate and mass loss rates were 45% and 17%, respectively. Hydrothermal oxidation treatment could reduce the CO2 reactivity of the coke and the treatment under supercritical condition is more effective. Hydrothermal oxidation treatment could improve the graphitization of the coke and smoothness of pore boundary in the coke and the treatment under supercritical condition is more effective.

Jan 1, 2016

By Maurizio Marezio Bertini

Successful treatment of contaminated sediments was achieved by sparging either 0.5 M NaOH solutions or distilled water with an SO2/O2 gas mixture. Metals such as Cu, Pb, Cr and Cd were successfully removed in a relatively short time. The effect of temperature and pH was investigated. Higher temperatures produced faster and higher recoveries with Pb and Cr more affected to temperature increase than Cu and Cd. The removal of copper, up to 50% percent, was achieved in alkaline solutions through the formation of copper sulfite complexes. The complete removal of metals such as Cu, Pb, Cr and Cd required that part of the treatment be carried out in acidic solutions. A preliminary cost analysis was carried out.

Jan 1, 2003

By Masahiro Hirasawa

"As a fundamental study on pyrometallurgical process that involves recycling steel-making dusts, of which major components are oxides of Zn and Fe, and waste polyvinyl chloride simultaneously ·at. a temperature below 1273 K, the reactions between the mixture of ZnO + Fe20 3 and PVC or the compound ZnFez04 and PVC are investigated in a series of thermogravimetric and small scale reactor experiments under inert atmosphere at below 1273 K. The reaction mechanisms are discussed· on the .basis of the thermogravimetric data. From the results of reactor experiments, it is shown that the chlorination of Zn in the oxides by Cl in PVC, the vaporization of ZnC12, the reduction of iron oxide to metal Fe by C and H in PVC, and, thereby, the separation of Zn and Fe in the oxides take place simultaneously at the temperature ~= 1200 K.IntroductionSteelmaking dusts are metallurgical wastes consisting mainly of oxides of Zn and Fe with smaller amounts of other heavy metal elements, such as Pb. In the recent investigation, [1] the present authors have investigated the fundamental aspects of a potential pyrometallurgical process· of recycling steel-making dust with polyvinyl chloride (PVC) at temperature T < 1273 K under Ar atmosphere. The performance of a similar process, in which HCl in the combustion gas of PVC is used to chlorinate Zn in the EAF dust under oxidizing atmosphere, has been investigated by Tailoka and Fray [2] with fundamental experiments. Figure 1 shows an example of the potential ·diagram of Zrt-Cl-0 and Fe-Cl-0 systems. In the figure, we can find two regions where ZnCl2(g) can be separated from Fe containing compounds. One is ZnCiz-Fe20 3 coexistence region at higher oxygen and chlorine potentials and the other is ZnCl2-Fe coexistence region at lower oxygen and chlorine potentials. The process adopted by Fray and coworkers is aimed mainly at the performance of Zn/Fe separation in the higher oxygen potential region. In the present study, the lower oxygen potential region is focused on."

Jan 1, 2000

By Yuanbo Zhang, Zhixiong You, Daoxian Duan, Guanghui Li, Tao Jiang, Xiaohui Fan

"Presently, high-grade manganese oxide ores are usually utilized by a coal-based reduction roasting process. However, there were some obvious drawbacks, including serious environmental pollution, high energy consumption, etc. The reduction temperature is relatively high (850-900 °C). In this study, a kind of biomass, pine black charcoal, was used as a reductant to reduce low-grade manganese oxide ores. Under the optimal conditions of reduction temperature of 600~650 °C, roasting time of 30~45 min and ratio of ore to reductant 5:1, the leaching efficiency of manganese reached more than 98%. Compared with the traditional coal-based reduction process, the reduction temperature is reduced by 250-300 °C.IntroductionManganese plays a very important strategic role in the national economy, and it is widely used not only in the metallurgical industry, but also in the light industry, chemical industry, medicine, agriculture, etc [1]. The average grade of manganese ores in China is evenly about 21%, which belongs to typical low-grade manganese ores [2]. Therefore, large quantity of high-grade manganese ores is required to import in order to meet the rapid development of Chinese manganese industry. As reported, the conventional treatment of reduction roasting has been widely applied for processing manganese oxide ores, in which coals or reducing gases (CO, H2 or CHi) were usually used as reducers [3]. However, there were some insuperable problems, such as high energy consumption, poor operating conditions, serious environmental pollution, etc [ 4-9]."

Jan 1, 2013

By B. Q. Li, H. C. de Groh, X. Lu

"A fully 3-D, transient finite element model is developed to represent the magnetic damping effects on complex fluid flow, heat transfer and electromagnetic field distributions in a metallic melt. The model development is based on our in-house finite element code for the fluid flow, heat transfer and electromagnetic field calculations. The numerical model is tested against numerical and experimental results for water as reported in literature. Various numerical simulations are carried out for the melt convection and temperature distribution with and without the presence of a transverse magnetic field. Numerical results show that magnetic damping can be effectively applied to stabilize melt flow, reduce turbulence and flow levels in the melt and over a certain threshold value a higher magnetic field resulted in a greater reduction in velocity. Also, for the study of melt flow instability, a long enough running time is needed to ensure the final fluid flow recirculation pattern. Moreover, numerical results suggest that there seems to exist a threshold value of applied magnetic field, above which magnetic damping becomes possible and below which the convection in the melt is actually enhanced.1. INTRODUCTIONThe imposition of a DC magnetic field on a moving, electrically conducting fluid, such as molten metal or semiconductor melt, produces an opposing Lorentz force that results in a reduction of flow velocity in the liquid. This effect has been explored in both the semiconductor and metals industries to control natural convection and/or surface tension induced Marangoni convection as well as thermally induced flow instability during solidification processing of these melts [1-6]. A mathematical model can be of great use in developing both fundamental understanding of the fluid-magnetic field interactions in these magnetically-assisted processing systems and basic guidelines for process design, control and optimization.This paper presents a 3-D mathematical model for magnetically damped fluid flow and heat transfer in a melt cavity, which is useful for interpreting results for unidirectional solidification processes at slow solidification rate, and some preliminary results concerning the magnetic damping effects on the flow instability in the melt. The model development is based on the finite element solution of the Navier-Stokes equations, energy equations and equations for induced electric field. The model is tested against reported results and is then applied to study the fluid flow and thermal distribution in the metallic melt with and without an external magnetic field."

Jan 1, 1999

By Xueming Lv

The rotary kiln-electric furnace (RKEF) process is the main method for producing ferronickel from nickel laterite ore. However, this process is energy intensive as it involves several high temperature steps. Therefore, a novel process is proposed to directly produce ferronickel from nickel laterite ore by semi-molten reduction, which is expected to be realized in a rotary hearth furnace (RHF). The RHF process is able to shorten the flow sheet, decrease the reaction temperature as well as reduce energy consumption. In this study, the influence of basicity on reduction of nickel laterite ore was investigated. The results showed that it is possible to produce the ferronickel nugget directly at 1400 °C when the quaternary basicity [(mCaO + mMgO)/(mSiO2 + mAl2O3)] was fixed at 0.60. Under this experimental condition, the grade and the recovery ratio of nickel reached 11.53% and 98.59%, and the grade and recovery ratio of Fe were 84.16% and 68.72%, respectively.

By Bora Derin, Adnan Aydin, Onuralp Yucel, Hakan Morcali

"The steelmaking industry which uses electric arc furnaces (EAF) generates approximately 250.000 tons of EAF flue dusts annually in Turkey. These flue dusts contain valuable metals such as zinc, iron and lead. For example, if these flue dusts can be treated efficiently, disposal problems certainly decreases and annually almost 40.000-75.000 tons of zinc can be recovered. In this study, powder and pellet forms of EAF flue dusts taken from a steel mill were carbothermally treated in a temperature controlled pilot scale rotary furnace via carbothermal reduction in order to investigate the reduction behavior of Zn and Pb. Temperature (900-1000 and 1100 °C) and time (0-90 minutes) were selected as reaction parameters. The chemical analysis was performed for the sample residues.IntroductionTurkey’s steel production reached to 23.3 million tons in 2006. There are three integrated steel plants of which capacities vary from 0.7 to 3 million tons per year and seventeen EAF steel plants of which capacities vary from 0.06 to 2 million tons per year [1]. When it is considered that more than 74 % of the Turkish steel production is produced by EAF method and approximately 10 - 15 kg of dust is formed per ton of steel during this process, the amount of annual generated EAF dust may be estimated at approximately 0.25 million tons. EAF dust which contains valuable metals such as zinc, lead, iron, cadmium, and chromium, is considered as hazardous waste product in steelmaking industry. If these flue dusts can be treated efficiently, not only the disposal problems certainly decrease, but also annually almost 40.000-75.000 tons of zinc can be recovered. Many studies which exist on recovering of the valuable metals from EAF dust, propose and practice many hydro-metallurgical and pyro-metallurgical treatments [2- 7]. In this study a laboratory scale work were performed to investigate reduction behavior of zinc and lead in EAF dust by carbothermal process in a rotary furnace."

Jan 1, 2008

By Xiao Yang

Calcium oxide is one of the major fluxing agents used for steel refining. Because unreacted CaO remains in slag in most cases, discharged slag is difficult to be recycled smoothly. With the growth of environmental concerns, improving utilization efficiency of CaO is required to reduce the amount of discharged slag and energy consumption. The authors have reported a resource and energy-saving process by using multi-phase flux for dephosphorization. Reaction behavior of phosphorus in multi-phase CaO–FeOX–SiO2–P2O5 flux system was investigated. Formation mechanism of P2O5-rich phases was clarified at the interface between solid CaO or 2CaO, SiO2 and molten CaO–FeOx–SiO2–P2O5 slag. Phase relationship and thermodynamic properties of 2CaO, SiO2-3CaO, P2O5 solid solution were observed to confirm the condensation of P2O5 in solid phase. Based on these results, reduction of CaO consumption, discharged slag curtailment, and energy-saving effects in the novel refining process by using multi-phase flux were discussed.

By Heinz Boeni, Daniel Ott, Uca Silva

"Latin America is facing a rapid increase in internet use. Penetration with electronic equipment is in some countries approaching the level of industrialized countries. There is an evident need to resolve the management of “end-of-life” computers and other electronic equipment. Several studies in Latin America assessed the increasing e-waste quantities and confirmed the importance of a sustainable e-waste management. This paper gives an overview on the status on e-waste management in Latin America, explains the challenges for establishing an e-waste management system in a developing country setting and highlights the social and economic potential and the possibilities of a regional approach.IntroductionGlobal ICT-Trade and generation of e-waste from ICTThe global production of electronic devices and particularly of Information and Communication Technologies (ICT) faces the biggest industrial expansion of the history: OECD figures show that global trade of ICT technologies has reached 7.7% of the gross world product by 2004, the major proportion accruing from China [1]. In 2006 an estimated 230 million computers and 1 billion cell phones have been sold worldwide which corresponds to a volume of 5’848’000 t [2]. As a consequence, Waste from Electrical and Electronic Equipment (WEEE), or e-waste, is by far the fastest growing waste component. It reaches more than 5% referred to Municipal Solid Waste and e-waste generation in developing countries according to UNEP is expected to triple by 2010 [2].According to the OECD e-waste is “any appliance using an electric power supply that has reached its end-of-life” [3]. The European WEEE directive [4] distinguishes 10 categories of ewaste: Big household appliances, Small Household Appliances, IT and Telecommunications Equipment, Consumer Equipment, Lighting Equipment, Electrical and Electronic Tools, Toys, Leisure and Sports Equipment, Medical devices, Monitoring and Control Instruments, and Automatic dispensers. In this paper e-waste and WEEE are used as synonyms. Focus will be laid on e-waste from IT equipment (IT-waste), corresponding to category 3 of the European WEEEDirective."

Jan 1, 2008

By Jeong-Soo, Joon Soo Kim, Rajesh Kumar, Sohn, Jin-Young Lee

"Liquid-liquid extraction (LLE) studies of tetravalent platinum from acidic chloride solutions have been carried out with Alamine 336 as an extractant diluted in kerosene. The title metal shows the inverse behavior at higher acid concentrations. Plot of log D vs. log [Acid], mol.L-1 gave a straight line with a negative slope of 0.8±0.03 indicating the exchange of one mole of hydrogen ions for every mole of platinum(IV) extracted into the organic phase. Extraction of platinum(IV) increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slope 1±0.3, indicating the association of one mole of extractant with the extracted metal species. The plot between metal distributions to aqueous to organic phases is 1.3±0.01; it indicates monomeric species was formed in organic phase. Stripping of metal from the loaded organic (LO) with mineral acids such as hydrochloric, sulphuric, nitric acids and bases like ammonia, hydrogen peroxide and sodium hydroxide are studied. The results indicated that hydrochloric acid and sodium hydroxide are the better stripping agents when compared with other acids and bases. Increase of temperature decreases the percentage extraction of metal indicating the process is endothermic. Regeneration and recycling capacity of Alamine 336 and extraction behavior of associated elements such as aluminium(III), magnesium(II), cobalt(II), iron(III) and nickel(II) were studied.IntroductionThe demand for platinum group metals (PGM’s) has risen in the last five years expected to keep in rising. Right now, the demand is already beyond the supply. The primary use of PGM’s today is in the automotive industry. Catalytic converters used in the PGM’s process to reduce greenhouse gases. Because of the current demand to reduce the green house effect the expected need for platinum is here stay. Country’s now advancing in the use of car production also are phasing increasing the needs for this metal. Chemical processing also use it, too. These industries account for more than 50% of all platinum production. Jewelry is other primary use of this precious metal whose value is much greater than gold. Other uses include computer data storage, scientific developments, fuel cell technology and in the glass manufacturing processes."

Jan 1, 2008

By Z. Q. Chen, M. H. Loretto, Y. G. Li

"As-cast, As-forged, as-solution-treated, and solution treated and aged microstructures of Ti-15Mo (IMI205) with and without carbon were examined using optical microscopy, scanning electron microscopy .and transmission electron microscopy. Tensile testing was carried out at room temperature. It was found that carbon acts primarily as a titanium carbide former: Titanium carbides increase slightly the tensile strength, but decrease the ductility of IMI205. These observations are interpreted in terms of the titanium carbide morphology observed using SEM and TEM and the phase diagrams of Ti-Mo, Ti-C, and Mo-C.IntroductionIn a recent study on the development of a burn-resistant 13-Ti alloy, carbon was introduced· into the Ti-V-Cr system in order to optimise the mechanical properties. Research results[1, 2] demonstrate that carbon addition can refine the 13 grain size and improve the stability of the 13 phase in Ti-V-Cr alloys. The most attractive result is that carbon addition produced a marked improvement in the ductility of alloys when the carbon content is over 0.1 wt.% in this alloy system. Even after long exposure, the alloy with carbon addition maintains good ductility. One of the main reasons for the ductilising of the alloy is that titanium carbides can getter the oxygen from the 13 matrix.In view of the success of carbon addition in improving the properties and the stability of the Ti-V-Cr alloy, it is of interest to investigate the behaviour of carbon addition in other beta Ti-base alloys. The objective of the present work was, therefore, to assess the microstructures and mechanical properties of IMI 205, a metastable beta titanium alloy, with and without carbon addition using optical microscopy (OM), scanning electron microscopy (SEM), transmission electron microscopy (TEM), wavelength dispersive X-ray (WDX) analysis, room temperature tensile testing."

Jan 1, 2000

By Mike Dry

While McCabe-Thiele plots are useful for designing single-component solvent extraction systems, not least because of their simplicity, they are less useful for multi-component solvent extraction. This paper presents a relatively simple method, compared to other approaches, for modelling solvent extraction as chemical equilibrium reactions between the various aqueous and organic species. The essence of this approach is how values for the equilibrium constants can be extracted from standard laboratory data. Synergistic solvent extraction of nickel is used to illustrate the method.

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By L. M. . Chia

The successful treatment of waste materials to recover metals with acceptable purity is often hampered by the presence of undesirable impurities. The problem is further complicated by the need to insure that any residues or solutions generated are environmentally acceptable. Hydrometallurgical processes involving leaching- solvent extraction-electrowinning offer some attractive features which address many of these problems. However, in certain instances trace impurities that contaminate the organics are difficult to chemically strip and interfere with the overall process efficiency. A new processing scheme has been developed which appears to provide some attractive alternatives for impurity removal from organics. It has been shown that many ionic impurities can be electrochemically removed from the organic by spontaneous direct reduction using solid metals. A variety of metal ion impurities have been removed from selected common organic extractants such as D2EHPA and TBP using different metals as the reducing agents. The results and probable mechanisms involved in the reactions are discussed.

Jan 1, 1994

By J. Rajesh Kumar

The extraction equilibrium study of tetravalent platinum was carried out using tri-octyl/decyl amine (Alamine 336) and bis(2,4,4-trimethylpentyl) monothiophosphinic acid (Cyanex 302) in kerosene from hydrochloric acid media to investigate their extraction capacity, since they have different donor atoms, ?N? and ?S?. Their distribution equlibria were studied as a function of acid, extractant, diluents and temperature. The title metal shows the inverse behavior at higher acid concentrations. Extraction of tetravalent platinum increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slopes 1±0.3, indicating the association of one mole of extractant with the extracted metal species. Stripping of metal from the loaded organic (LO) with mineral acids and bases such as hydrochloric, sulphuric, nitric acids and ammonia, hydrogen peroxide, sodium hydroxide, thio- urea were studied. Regeneration and recycling capacity of Alamine 336/Cyanex 302 and extraction behavior of associated elements was also studied.

Jan 1, 2009

By M. Pineau, G. A. Monteith, M. Laliberte, G. Houlachi

Conventional physico-chemical treatment methods, either hydroxide or sulfide precipitation, can hardly achieve a high removal of selenium from the liquid effluents which can be generated in some metallurgical operations. In weak acid solutions, selenium exists mainly as anionic species (selenite Se03-2 and selenate SeCV2) which, therefore, cannot precipitate as metal hydroxide or metal sulfide compounds. At the same time, neither selenite nor selenate form stable precipitates with the common cations (Ca, Mg, Fe, etc.) that are typically used in water treatment. At Noranda Inc., CEZinc Division in Valleyfield, Canada, the introduction of new discharge requirements for effluent toxicity initiated a R&D program which resulted in the full-scale implementation of a new treatment method for selenium removal. The goal of this paper is to present this new method which is now being patented by CEZinc. The process chemistry will be presented along with pilot-scale developments and full-scale operational results.

Jan 1, 2000

By Richard D. Hagni

Ore microscopy is a useful technique to detect and study the ore minerals that are associated with sediment-hosted and volcanic-hosted deposits of finely disseminated gold and silver. Ore microscopy can be used to determine the: 1) precious metal-bearing minerals in some ores, 2) associated ore minerals that may form geochemical exploration halos, 3) character of iron sulfide grains, 4) extent of sulfide oxidation, 5) character of oxidized iron minerals, 6) character of original sulfide grains from a study of the hypogene and supergene oxidized ores, 7) relative time of oxidation, 8) character of organic matter, 9) minerals that may consume excessive amounts of cyanide solution, 10) extent of silicification and silica encapsulation, and 11) possibility of salting.

Jan 1, 1987

By K. H. Ho

This paper describes a simplified numerical model which is used to study the skull formation of liquid metal on a rapidly rotating disc in centrifugal atomisation. The skull formation is one of the problems limiting the wide use of centrifugal atomisation. The enlarging skull on the atomising disc reduces the yield of metal powder produced and produces a resistance to the centrifugal force which worsens the quality of the powder. It is costly and often difficult to study the flow behaviour by experiments due to the complex heat transfer and phase transformation during the processing. Computer modelling is therefore a powerful tool for mechanistic understanding of centrifugal atomisation. This paper investigates the flow pattern of the melt on the rotating disc as a function of initial temperature, melt flow rate and disc rotation speed as well as the physical properties of the melt, such as density, surface tension and viscosity using the commercial package Flow-3D. Keywords: Solidification, Rotating disk, Centrifugal Atomization

Jan 1, 2003

By Jörg Wallner

In order to limit SO2 emissions, the Montanwerke Brixlegg AG has installed a desulphurisation plant with the primary aim of reducing the peak emissions from the copper converter that are of particular ecological concern. The author discusses the process requirements, the desulphurisation process selected and the results achieved.

Jan 1, 1996

By I. Sofia Fernandez del Rio

This paper describes a process for the treatment of the dusts generated during the operation of blast and reverberatory furnaces in the lead smelter, to remove zinc, cadmium, arsenic and halides from the circuit. The process consists of a Pefloles' developed leaching/purification stage and a solvent extraction process developed by Lurgi. The plant capacity is 5,000 tonnes Zn/year. The feed to solvent extraction contains 8 g/1 Zn. Impurities such as copper, iron, arsenic and cadmium are removed by conventional cementation processes. The cadmium product is 99.99 % pure. The solvent extraction process consists of two extraction stages, one washing stage and two stripping stages. D2EHPA is used as the extraction agent and 25% ammonia as the neutralizer. The rich-zinc solution is sent to the electrolytic zinc plant for zinc recovery. The raffinate produced, which is a mixture of ammonium sulfate and chloride, is used for agricultural applications.

Jan 1, 2000