Search Documents

By Naiyi Li, Henry Hu, Alfred Yu

"In the past few years, various squeeze cast aluminum components have been developed and successfully implemented in various vehicles by the automotive industry because of their superior engineering performance. However, fundamental understanding of the formation of air gap during squeeze casting processes is still very limited despite of its significant influence on the extent of heat transfer between the casting and mould. In this paper, a mathematical model has been developed to simulate phenomena of air gap between the casting and mold' during squeeze casting of aluminum alloys. The model considers the effect of process parameters such as applied pressures and mold temperatures on the events of air gap formation. The predication indicates that the occurrence of highly enhanced heat transfer in squeeze casting of aluminum alloys primarily results from the presence of excess applied pressures.IntroductionA number of squeeze cast Al components has been developed and used in mass-produced vehicles in the past few years, such as steering knuckles, Road wheel, Engine Block etc. This is attributed to their superior engineering performance. In squeeze casting, the cooling rate can be increased by applying high pressure during solidification which results in the noted refinement in the micro structure scale leading to better casting properties. However, the excessive pressure increased interfacial heat transfer coefficient is affected during the solidification by air gap formation and die surface condition etc., which is believed to increase thermal resistance at the casting/die interface [l - 4]."

Jan 1, 2004

By W. Murray Small

Nickel plays an important role in determining the properties of many stainless steels and superalloys. Cobalt also contributes significantly to the performance of certain grades of superalloys. A major technical aspect, in which both of these metallic elements are involved, concerns the solubility of nitrogen in these classes of alloys. Beyond certain content limits, dissolved nitrogen may contribute to the deleterious mechanical behavior by these alloys. It is therefore essential to control the level of this element during alloy processing. In this paper, results from several experimental studies have been assembled and are analyzed to describe phenomena related to the individual effects of nickel and cobalt on the solution of nitrogen in several groups of alloys. Both solid and liquid alloy systems are considered. This information may be used as a guide to limit or control the presence of this interstitial element in alloys.

Jan 1, 1993

By T. M. Dreher

The difficulties associated with the operation of a classical rhodium refining process have prompted many attempts to develop a viable solvent extraction flowsheet for rhodium. Recent investigations at McGill University have involved the activation of rhodium prior to its solvent extraction. The role of activation is to convert the aquochloro complexes of rhodium to a form extractable by conventional solvent extraction reagents. In the novel separation scheme identified, chloro complexes of rhodium are converted to bromo complexes, which undergo aquation to a lesser extent, making them more easily extracted. Rhodium is then extracted using Kelex 100, and stripping is achieved by use of a concentrated chloride based solution. Separation of rhodium from iridium is achieved by either prior reduction of Ir(IV) to Ir(III), as the latter is not extracted, or via co-extraction and differential stripping. A conceptual flowsheet for the refining of rhodium using this method is proposed.

Jan 1, 1998

By T. P. R. de Jong

Dual energy X-ray transmission imaging is extensively applied for safety luggage inspection. Its advantages are its rapid scanning rate (25 to 100 cm/sec) at approximately I mm resolution and simultaneous thickness independent metal identification. This is especially advantageous for secondary scrap metal inspection and automatic sorting. Other applications include metal product inspection, bale control, and waste processing. Recent progress in development of an automatic on-line sorter for bulk solids is presented and discussed. Besides various non-metal applications (solid fuels, wastes etc.) it appeared particularly effective in light metal sorting. As inspection tool better control of difficult to monitor solid bulk streams, batteries, bales and other related metals becomes possible.

Jan 1, 2003

By Jeffrey W. Braithwaite

The laboratory characterization of the oxidation of chalcopyrite under conditions of deep solution mining is presented in this paper. A salient feature of this system is the pH buffering effect resulting from simultaneous acid producing and acid consuming oxidation reactions. The solution chemistry and related sulfur partitioning of the oxidation reactions are detailed. The contribution of temperature, acid concentration, oxygen pressure, particle size, and solution additions to the kinetics of copper extraction are presented. A mixed kinetic model was used to describe the kinetics of oxidation.

Jan 1, 1976

By Scott Samson, Weidong Wang, Shekhar Bhansali, Vandana Upadhyay

"We present an improved design for the two-arm polysilicon thermal actuator. The classic thermal actuator design produces a localized hot spot at approximately the center of the thin actuator arm. This phenomenon limits the actuator efficiency, lifetime, and reliability. Since the actuator deflection is based on thermal expansion of the material, advantage may be gained by making the temperature profile more uniform along the hot-arm length. In our design, the geometry of the thin arm is modified by forming a nonlinear structure near the approximate location of the original hot spot. Electromechanical simulations of this design show an increase in deflection, due to a flattening of the temperature profile along the hot arm. The solid model generation, finite element analysis and simulations are carried out using PEA software. Experimental devices are in the process of being fabricated by using a polysilicon rnicromachining process.1. IntroductionMost active MEMS devices employ some kind of actuating mechanism to increase functionality. Various actuating mechanisms like magnetic, electrostatic, thermal, magnetostatic and piezoelectric have been investigated and incorporated for actuating microstructures. The primary features required from many on-chip actuating mechanisms are large deflection (>10 µm), low actuation voltage, low power.consumption, reliability, fast response, ease of design and fabrication, and small size. Thermal actuation is an attractive mechanism for rnicromechanical devices requiring high actuation forces, large deflections, good linearity and low actuation voltage. Thermal actuators, also known as ""electrothermal actuators"", ""heatuators"" or ""U-shaped thermal actuators"", have been largely used in MEMS based devices to provide both in-plane and out-of-plane actuation [l] .Thermal actuators are also easily compatible with standard CMOS circuitry due to their low driving voltage. However, high power consumption remains a major drawback of the thermal actuation mechanism."

Jan 1, 2004

By Farzaneh Sadri

After water leaching of an acid baked REE concentrate, impurities such as Fe, Al, Th, and Cu are removed by neutralization with different reagents such as NaOH, Mg(OH)2, MgCO3, CaO, and CaCO3. Among these chemicals, lime (CaO) and limestone (CaCO3) are the preferred reagents due to their low costs. However, because of calcium sulfate dihydrate (gypsum) precipitation, they are not so common in industry. One of the disadvantages of gypsum precipitation is the adsorption of REE to the precipitates, losing a fraction of REE to gypsum which is hard to recover. In this paper, batch and continuous conditions in the impurity removal process using limestone are investigated and the differences between these two processes are examined. Based on the experiments, REE uptake by gypsum significantly increases in continuous processes, and different gypsum morphologies are observed.

By Tomoji Kawai

"The Pulsed Laser Deposition method using multi-targets is extremely useful for the creation of functional multi-layers and variety of artificial lattices. The topic of the present talk is on the creation of ''Function hannonized artificial lattices by laser ablation"" made of the combined magnetic, ferroelectiric and superconducting layers. The outline of talk is,1. Features of Pulsed Laser Deposition method (Laser Molecular RHEED and S1M/AFM.2. Creation of magnetic, dielectric and superconducting artificial lattices by Pulsed Laser Deposition.3. Novel properties of function harmonized artificial lattices: especially on the magnetic and magnetoresistive artificial The outline of talk is, lattices made of3d transition metal oxides."

Jan 1, 2000

By H. Y. Cheng

A pulse column solvent extraction system was evaluated as an alternative to mixer-settlers for the separation and purification of rare earths. The column tested had an inside diameter of 44.5 mm and had 36 sieve plates with a free area of 25%. Pulsing was provided pneumatically using a solenoid valve controlled by a timer so that both pulse amplitude and frequency could be varied. Feed to the column was a mixed rare earth chloride solution containing 10 g RE L-1. The extractant was 5% Ionquest® 801 in Shellsol 2037 diluent. Hydraulic performance of the pulse column was excellent with no propensity towards stable emulsions or crud formation under normal operating conditions. The column was operated in organic-continuous mode with flow rates chosen so that yttrium and the heavy rare earths were extracted with high efficiency while the light rare earths were rejected. Yttrium extraction varied from 83 to 99.2%. Concentration profiles were measured in both the aqueous and organic phases, and, from this data, the height of a transfer unit (HTU), the mass transfer coefficient (Kxa) and the continuous-phase axial dispersion coefficient (Ey) were computed. The HTU ranged from 17-92 an which is within the range of values reported for other (non rare earth) pulse column systems.

Jan 1, 1992

By L. J. Lutz

The U.S. Bureau of Mines has developed an electrorefining process to recover Ni, Co, Cr, and other metals from mixed and contaminated superalloy scrap. The superalloy scrap is cleaned then directly electrodeposited as a Ni -Co deposit. The process recovers approximately 90 pct of the Ni-Co available from the scrap as a 99t pct pure Ni-Co alloy. During electrorefining the electrolyte undergoes a purification process which results in Cr and other refractory metals reporting to the purification residue. Operating data is given for a 3-L compartmented electrolytic cell. Techniques for the removal of Fe, Cr, and trace impurities from the recycled electrolyte are outlined. The economics of a facility producing 15 mt/d of a Ni-Co alloy are also discussed.

Jan 1, 1993

A novel process is being developed for metal recovery from waste electrical and electronic equipment involving a leach reactor coupled to an electrochemical reactor. Metals such as Ag, Au, Cu, Pb, Pd, Sn etc. are dissolved from shredded electronic scrap in an acidic aqueous chloride electrolyte by oxidising them with aqueous dissolved chlorine species. In the electrochemical reactor: (i) chlorine is generated at the anode for use as the oxidant in the leach reactor, and, simultaneously, (ii) at the cathode, the dissolved metals are electrodeposited from the leach solution. The extended Butler-Volmer equation was used to provide predictions of the electrode potential dependences of partial current densities and, hence, total current densities, current efficiencies and alloy compositions for acidic aqueous chloride electrolytes containing Ag(I), Au(III), Cu(II), Pb(II), Pd(IV) and Sn(IV) species, together with dissolved chlorine. With judicious choice of kinetic parameters, the predicted total current density ? electrode potential behaviour of such solutions was in good agreement with experimental data for a rotating Pt disc electrode. Reduction of dissolved chlorine at a Pt rotating disc electrode exhibited mass transport controlled behaviour, in agreement with Levich?s equation over the potential range 0.3-0.9 V (SHE). This could form the basis of a linear sensor, possibly using a microelectrode for measurement and control of the dissolved chlorine concentration in the efflux of leach reactors and inlet to electrowinning reactors in the envisaged process.

Jan 1, 2003

By G. Haesebroek

In L969 Metallurgie Hoboken-Overpelt started an industrial plant for the separation of iron and zinc from a concentrated CoCL2 solution. Iron and zinc are extracted in column contactors by a solvent containing 12 vol % of tertiary amines in xylene. The extracted metals are stripped from the pregnant organic phase by precipitation with a NaOH solution at pH LL. In this paper an overview is given of the industrial process. In order to overcome some drawbacks of this process (low flash point of the diluent, reagent consumption, batchwise stripping) an alternative solvent extraction process has been examined. In this alternative process, iron and zinc are extracted with an or¬ganic phase containing 50 vol % of TBP in Escaid 110. The pregnant solvent is stripped with water in conventional mixer settlers. Despite the ability of this process to overcome most of the inconveniences due to the use of tertiary amines, it suffers from the poor stability of TBP in concentrated chloride solutions, resulting in unavoidable and inacceptable precipitation phenomena in the stripping section.

Jan 1, 1988

By Jong-Jip Kim, J. G. Byrne, W. Kim, In-Ok Shim, John E. Flinn

"Two rapid solidification processes for 304 stainless steel were studied: centrifugal atomization (CA) in a helium atmosphere and atomization by exposing argon-containing melt to vacuum (VGA). Positron annihilation and x-ray line broadening measurements of explosively consolidated monoliths were used to clarify microhardness measurements as a function of annealing temperature. Interesting differences in positron response between CA and VGA materials are ascribed to more carbide formation in the CA material than in the VGA material in the 600 0C range. In addition, hot isostatic pressing of the CA material was examined as to the relations between mechanical behavior, pore shape, and relative density. A variable stress concentration factor is introduced into the theory to allow for changing pore shape as relative density increases.IntroductionThere are many potential advantages of rapid solidification processing (RSP), such as a high degree of matrix supersaturation, finely dispersed microstructures, improved chemical homogeneity, and retention of metastable phases, which have been studied extensively. To consolidate rapidly solidified material which is in powder form into useful shapes often requires subjecting the material to elevated temperature for extended periods of time under mechanical forces, as in hot isostatic pressing or hot extrusion. In such cases, some of the characteristics of the rapid-cooling step can be strongly affected. An alternative is dynamic consolidation (1), for example by explosive forming, where the time frame at least is extremely short.In the present work, effects of the consolidation processes of hot isostatic pressing (HIP) and explosive forming in a die are examined. The particular material is 304 stainless steel. The characteristics of both RS and VGA 304 stainless-steel powders were described by Wright, Flinn, and Korth (2) earlier."

Jan 1, 1988

By Renaud Metz

The DOPA process (Direct Oxidation of a Precursor Alloy) was used to prepare ceramic powders based on doped SnO2 and ZnO. The DOPA process consists essentially in the direct oxidation of a homogeneous precursor alloy. A unique advantage of this process is its rather benign environmental impact since no dangerous reactants are used and no harmful by-products are generated. Only oxygen and the alloy metals participate on the chemical reaction to produce the multi-component oxide. Homogeneous alloys of niobium, cobalt and chromium doped tin have been prepared. The molten metal alloy is atomised in air using a double fluid nozzle to produce metallic powders. A subsequent thermal treatment is carried out to fully oxidise the sprayed metal alloy powders. These raw powders are used to prepare a ceramic powder through a mill homogenisation and atomisation process. The ceramic powder is then uniaxially compacted in disc shape and sintered in an oxidising atmosphere. The resulting sintered bodies are metallised on their flat faces and the cylindrical surface is passivated using lead free glass enamel. These ceramics present excellent semiconducting properties with non-linear (non-ohmic) characteristics. The DOPA process is found to be an attractive procedure to obtain ceramic powders for the preparation of SnO2 varistors.

Jan 1, 2006

By V. A. Bryukvin

It has been found that by superimposing symmetric alternating current over the process, the rate of nickel and cobalt leaching from metallized products with copper sulfate solutions increases by a factor of 1.5 to 2.0 and the apparent activation energy of the process investigated is reduced from 12 down to 6.6 kcal/mole. It appears especially attractive to use alternating current for anodic dissolution (oxidation) of metallic scrap of refractory metals and their alloys in ammonia electrolytes permits production of high-grade commercial products in the form of respective ammonium salts using a short and virtually reagent-free process flowsheet. Similar approaches can be applied also for electrochemical processing of nickel and copper scrap in sulfuric acid media with subsequent recovery of pure sulfate salts or electrolytic processing. Electrochemical technology for recycling of tungsten-cobalt (WC 15) and tungsten-rhenium (WR 20) alloys has been also investigated. In the former case, anodic oxidation of carbide alloy was carried out in nitric acid electrolyte with production of pure tungstic acid. The research conducted has indicated that the physicochemical effect of alternating current results in a lower activation energy of electrode reactions due to changes in the mechanisms of the electrode reactions themselves.

Jan 1, 2006

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

By S. Abe

Various copper anodes to be electrorefined were subjected to a heat treatment comprising annealing at a temperature in the range of 700 °c to 1,000 °c followed by a slow cooling preferably on the order of about 150 °c, and using these heat treated anodes , a series of dissolution experiments were conducted under conventional electrorefining conditions. The results obtained have indicated that the above annealing/slow cooling process dramatically improves the dissolution activity regardless of the type of anodes. As an example, passivation times of l to 3 minutes in a standard test have been increased to more than 80 minutes by this innovated heat treatment. Other advantages sterning from the improved anodic activity include reduced electrical short circuiting which results in substantial labor effort in the tankhouse, reduced energy requirement, and reduced cost of processing anode slimes because the amount of anode slimes is reduced. In addition, this process gives rise to a dramatic change in the nature of anode slime layer formed in such a way that a comparable final cathode copper product can be achieved even from high-impurity copper starting material.

Jan 1, 1987

By Jilai Xue, Jun Zhu, Germain Kouma Ndong, Qiaochu Liu, Luxing Feng

"High-temperature oxidation and corrosion behaviors of Ni-Fe-Cr alloy as inert anodes for aluminum electrolysis have been studied in oxygen and molten electrolyte. The oxidation and corrosion scales on the anodes tested were analyzed using XRD and SEM-EDS. The oxidation rate is found to increase with increasing temperature from 700 °C to 950 °C, which can be approximately described by an inverse power rate function. The oxidation scales at 750 °C, 920 °C and 950 °C contain Cr-rich phase along with FeCr204 and (Feo.6Cro4)203. The corrosion extent of Ni-Fe-Cr anodes in electrolyte is dominated by temperature, which can make the scales thickness double from 700 °C to 750 °C or from 920 °C to 950 °C. Cr and Fe in the scales on the anode in electrolysis corrode preferentially into the molten electrolyte, while the nickel oxides could better sustain the corrosive environment in electrolysis. The results can be useful for developing inert anode material for potential application in aluminum electrolysis.IntroductionThe development of an inert anode for aluminum electrolysis has been a long term goal for aluminum industry. The present process for primary aluminum production involves the reduction of alumina with carbon anodes, forming carbon dioxide:"

Jan 1, 2013

By Xuewei Lv

An intelligent recognition and quantification system for the micrographs iron ore sinter was developed in the current paper. The average distribution parameters in a gray histogram of minerals by a Gaussian gray distribution model were obtained. The feature curves of the gray histogram of two minerals were achieved by combining the two density functions. The feature indexes, such as the number and position of the peaks and the valleys of two minerals in different ratios, were quantified by differentiating the distribution functions. This algorithm is able to extract the feature of the minerals adequately and accurately for recognizing the composition and phases of the minerals intelligently.

Jan 1, 2009

By Florian Kongoli

Slags and fluxes are important interchangeable dimensions of pyrometallurgical processes. They can increase the efficiency of the smelting, converting and refining processes and improve the quality of the final products. A good slag should have appropriate physicochemical properties such as low liquidus temperature, optimal viscosity, maximum ability to attract undesirable elements, minimum potential of attracting valuable elements, etc .. A good flux, on the other hand, when properly used, can considerably improve the physicochemical properties of the slag since by modifYing its chemical composition it could decrease the liquidus temperature, improve viscosity etc.. Consequently, the choice of a good slag and the corresponding fluxing strategies has become indispensable in most of industrial processes. However, the properties of multi component slags as well as the effect of several fluxes are known only empirically and confusion exists in the literature and in the industrial practice. In today's reality of frequent changes in the composition of raw materials and that of the fluxes themselves, in the existing or new developing technologies, the quantification of the thermophysicochemical properties of multicomponent slags and the effect of fluxes becomes indispensable. This paper reviews some of the work carried out by the author's group during the last ten years on the quantification of the thermophysicochemical properties of multicomponent slags and on the effect of fluxes in several smelting and converting processes in close relation to their individual characteristics. Several examples have been given in order to demonstrate the fact that when taken outside the context some fluxes can become in fact anti-fluxes.

Jan 1, 2003