Search Documents

By A. V. Tarasov

The lack of technology for processing of sub-grade ore concentrates and intermediate products for extraction of Zn, Pb, Cu and precious metals at the metallurgical stage was a constraint for an increase in the production of these metals. The technology developed in the Gintsvetmet Institute is based on an improved electrothermal smelting process for treating calcined charge, ensuring thereby a reduction in power requirement and improving the environmental performance of the process. Electric smelting of sub-grade polymetallic concentrates produces lead bullion, to which the bulk of gold and silver reports, as well as well segregated matte and slag concentrating the bulk of zinc. Lead bullion and matte are commercial-grade products; zinc is recovered from high-grade (15% Zn) slag by slag fuming process. Reduced loss of precious metals in slag ensured by the given technology is attributed to the fact that the slag contacts with matte with low contents of gold, silver and lead, rather than with lead bullion. Limited amounts of off-gas typical of electrothermal processes ensure cost-effective operation of dust recovery devices and a reduction in emissions of harmful pollutants into the ambient air.

Jan 1, 2002

By D. V. Hughes, J. R. Nyberg

"Since 1985, a comprehensive automation system has been installed at the Outokumpu Oy Zinc Plant, Kokkola, Finland. In leaching and solution purification special sample handling equipment, on-line analyzers and instruments, and a computer-based control system with duplicated supervisory stations have been installed. The system has enabled closer control of the process and more efficient use of labor. Since its installation recovery of zinc has improved, and use of zinc dust, steam, and water have decreased. The system has performed reliably. It includes optimizing programs and process study tools, which facilitate improving process performance. An expert system has been built-up to prompt process personnel to take appropriate action on the basis of process data. In electrolysis a similar system, based on extensive monitoring of the process and of production of zinc cathodes, is used to maximize- current efficiency by maintaining optimum conditions in the process. It is planned that in the future the control systems will be integrated and extended to cover the roasting plant and effluent control.IntroductionThe Zinc PlantThe Zinc Plant of Outokumpu Oy Metallurgical Division at Kokkola, on the West Coast of Finland, has grown from a 90,000 t/a plant founded in 1969 to become, with its present capacity of 170,000 t/a, one of the world's ten largest zinc plants. Especially since the completion in 1988 of a thorough modernization programme, it is also among the world's most modern.The Kokkola plant takes its raw materials from Outokumpu's own mines, Vihanti and Pyhasalmi in Finland, and Tara in Ireland, and from outside sources. Concentrates are roasted in two Lurgi fluid-bed furnaces, and the calcine is leached and iron removed by the Conversion process. Following this copper, cobalt, and cadmium are removed, and zinc is refined by electrowinning. The leaching and purification, and the cell-house are automated under computer-based control, and anode and cathode handling in the cell-house are mechanized and fully automatic."

Jan 1, 1989

By Joel A. Huffinan

"This presentation is being given to better inform the audience of the dependability of precious metal analysis by fire assay. A brief explanation, however, of standard fire assay exploration procedures will be given. An overview of other types of analyses by fire assay will be discussed as well, and the operation of a modern day assay laboratory.IntroductionThe use of lead oxide for the fire assay process dates back to the finds in Troy II and the Cappadocian Tablets about 3,000 B.C. Some advances have been made in the basic procedures due to instrumentation and electronics, but the fusion and cupellation procedures used in fire assay remain much the same as during this period.In 1600 AD. Agricola was the first to take a scientific approach to fire assay recording methods and procedures used (Hillerbrand and Allen, 1905) [1]. Since this period, much of the recognized research into the analysis of ores and metals was carried out in the late 1800's and early 1900's prior to World War II, and again after the deregulation of precious metals. The renewed interest in precious metals mining and metallurgy are due much to advances in precious metals heap leaching in late 1970's."

Jan 1, 1999

By Alex Luyima, Jaan Kers, Lifeng Zhang

"The pyrolysis of PWBs was investigated by a TG-DTA-MS furnace at 300–1173 K. The kinetics and the control of emitted gas during the pyrolysis of PWBs with and without chemical additives were studied. Moreover, the possibility of controlling the amount of toxic exhaust gases like HBr, C6H6, Br2, Cl2, HCl gas and recovering beneficial gaseous fuels like CH4 and H2 from pyrolysis process is discussed. The MS data for each PWB sample were examined as a function of temperature and particular m/z values could be associated with the mass loss steps in the TG data. The degradation of the organic material was characterized by m/z = 2, 16, 18, 28, 36, 44, 71, 78, 81, and 160. Fe2O3 was the best inhibitor of toxic HBr and C6H6 when compared to Al2O3, CaO Y-zeolite and ZSM-5. Moreover, it had no significant effect on the valuable H2 and CH4 gas evolution. This selective inhibition of toxic gases while maintaining the valuable ones make Fe2O3 the best candidate among the investigated additives in controlling gas emissions from PWB pyrolysis process.IntroductionThe electronic and electric industry is one of the world’s largest and fastest growing manufacturing sectors. As a consequence of this growth, electrical and electronic waste (e-waste), such as computers, washing machines, printers, mobile phones, television sets, stereos, radios, etc., is generated in large quantities around the world. Printed wiring boards (PWBs) are a common component of many electronic and electric systems.[1]. The rapid development and expansion of the electronics industry over the past several decades have led to a dramatic increase in the production of PWBs and a corresponding increase in the amount of waste generated from both production and disposal. The environmental impacts of the treatment and recycling of PWBs waste have become a major concern [1-2]. PWBs are particularly problematic to recycle because of the heterogeneous mix of organic material, metals, and glass fiber [1]."

Jan 1, 2012

By Fathi Habashi

Laboratory autoclaves for hydrometallurgical investigations are available in a variety of sizes, models, and materials of constructions. They vary in sizes from 25 mL to 2 liters for laboratory studies and 5 to 50 gallons for pilot plant work. They are essential tools for studying aqueous oxidation of sulfide concentrates, dissolution of oxide minerals at high temperature and pressure and hydrothermal precipitation reactions. The maximum pressure and temperature at which any pressure vessel can be used will depend upon the design of the vessel and the materials used in its construction. Since all materials lose strength at elevated temperatures, any pressure rating must be stated in terms of the temperature at which it applies. A review of existing models and their accessories will be given.

Jan 1, 2000

By C. J. Beyke

Slags and/or mattes from three secondary lead producers were studied as part of an effort to develop treatment methods for these lead-bearing residues. Each company used a somewhat different production process. Company A used a reverberatory furnace followed by a blast furnace. Company B used only a blast furnace. Company C used both a reverberatory and a blast furnace, and the scrap material was desulfurized with sodium carbonate prior to smelting. The slag matrix produced from sulfur-bearing scrap consisted mainly of iron-calcium silicates; the slag from desulfurized material was similar, but also contained sodium. In all the slags most lead was present in metallic form, often alloyed with tin, antimony, arsenic, and/or iron. Slag from Company B contained the most alloying elements, often as discrete subparticles within the lead droplets. Mattes were produced at Companies A and B; predominant phases were pyrrhotite and magnetite, while lead was present in metallic form and as galena.

Jan 1, 1995

By E. Salinas-Rodriguez, J. Hernández-Ávila, E. O. Ávila-Dávila, A. Romero-Serrano, M. Perez-Labra, G. Juárez-López

"Single phase rubidium jarosite was synthesized by precipitation from aqueous solution. X-ray diffraction and SEM-EDS analyses showed that the synthetic rubidium jarosite formed in subspherical particles with an average particle size of about 35 µm. The chemical analysis showed an approximate composition of Rbo9432Fe3(SO4)2 1245(OH)6. The decomposition behaviour of the jarosite in terms of solution pH was thermodynamically modeled using FACTSage by constructing the potential-pH diagram at 298.15 K. The E-pH diagram showed that the decomposition of jarosite leads to goethite (FeOOH) together with Rb+ and SO42- ions. The experimental decomposition of the Rb-jarosite was carried out in alkaline solutions with five different Ca(OH)2 concentrations. The decomposition process showed an ""induction period"" followed y a progressive conversion period where the Rb+ and SO42- ions formed in the aqueous solution. In contrast, calcium was incorporated in the solid residue and iron was transformed into amorphous ferrihydrite. The kinetic analysis showed that this process can be represented by the unreacted-core chemically controlled model. The reaction order with respect to Ca(OH)2 is 0.4342 and the calculated activation energy is 98.70 kJ mol-1. IntroductionJarosite type compounds are hydrous sulfate minerals containing alkalis and ferric ions, MFe3(SO4)2(OH)6, where M can be H3O+· Na+, K+, Rb+, Ag+, NH4 +, Tl+, ½ Pb2+ or ½ Hg2+. Jarosite-type compounds were formed by the natural ""in situ"" oxidation of pyritic ores leading to the replacement of the original iron sulfides and iron oxides (Dutrizac and Kaiman) [1]. The great interest in jarosites is due to its ability to eliminate or diminish the iron concentration of the acid leach solutions produced in the hydrometallurgical zinc process, with relatively low losses of divalent metals such as Zn2+, Cd2+, Cu2+ or Co . However, the losses of the metal values demand a careful study of the conditions under which the jarosite compounds are formed together with their chemical properties."

Jan 1, 2012

By W. Mueller

The function of a process mineralogist in the operation of a copper mine and plant is to assist in the identification and classification of the operation's main throughput. These include ore, concentrates, slag and matte, and to a lesser extent, refined products. In addition, a number of other products not normally thought of in association with mineralogy are examined. These include scales from submersible pumps, failed boiler tubes, acid plant, and shaft furnace; characterization of inclusions in failed compressor gear teeth as well as in copper rod; and flue dusts from a smelter, air transported particulates and coatings on passive copper anodes in the refinery. Techniques and equipment required for these studies include simple hand magnets to the high intensity Isodynamic separator, visual examination to electron microscopes, x-ray equipment, DTA, IR, heavy liquid separation, and contracted services of custom laboratories. Several examined products from Magma Copper Company have been selected to illustrate the range of techniques and equipment required by a process mineralogist.

Jan 1, 1981

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By Bien Ferrer

In most smelting operations, there is a strong incentive to improve safety, reduce downtime and extend the campaigns of furnaces and related equipment. An asset management strategy that is based on information, rather than simple throughput metrics and intuition, can be developed to improve uptime and unlock value currently unrealized at existing smelters. Advances in digital technology, including data analysis, modelling and monitoring for hot pyro-metallurgical vessels, make it possible to assess the current condition of an asset, as well as to make more informed projections about its future condition, using on-line and historical data. This would allow practices around asset management to be more proactive and less reactive, with the end-result of optimized uptime. ‘Digital Asset Management’ describes a concept in which digital technology is used to support an asset management strategy and accelerate decision-making by providing information on what, why and how an asset should be designed, operated or maintained. With the overall goals of effective resource utilization, optimized operations, capital efficiency and social acceptance, Smelter 4.0 is a program of holistic improvement and is underpinned by the effective use of data to drive decisions. This paper focuses on Asset Reliability, which is one of the improvement pillars of Smelter 4.0, and introduces a methodology that is aimed at closing the gap between recorded data and evidence-based decision-making through Digital Asset Management.

By Gaifeng Xue, Xiaohong Xu, Meng Liu, Yijie Song, Guotao Xu, Jixiong Liu

BN (Boron Nitride) based composites were prepared with hot-pressing by using h-BN as main material in ceramic preparation process. The relative density, bending strength, vickers’ hardness, thermal shock resistance, thermal expansion coefficient, thermal conductivity, phase composition and microstructure were tested and analyzed by using modern testing technology. The results indicate that the best formula is B, the relative density is 97%, the bending strength is 260 MPa, the hardness is HV5 343kg/mm2, the thermal expansion coefficient is 2.8×10-6℃-1, the thermal conductivity is 22 W/(m.K) and have no crack after thermal shock for 20 times by water cool. XRD analysis indicates that the main phase compositions are h-BN, β-Si3N4 and sialon. SEM studies show that the grains wrapped up by solid solution.

Jan 1, 2015

By Yang Hong-ying, Yu Juan

Electrochemical behavior of natural chalcopyrite in electrolyte solution at pH value of 6.97 was studied by cyclic voltammetry, X-ray photoelectron spectroscopy and electrochemical impedance spectroscopy. The results showed that the electrochemical processes occurred on electrode surface were controlled mainly by the growth of sulfur species at lower applied potentials (<0.35Vvs.SHE), and the oxidative dissolution of sulfur species and the hydroxylation of iron at higher applied potential (>0.45V). The EIS spectra of oxide product layers could be illustrated by the equivalent circuit of Re(QdlRct(QfRf)), and the degree of hydrophilicity for chalcopyrite was higher when the value of charge transfer resistance Rct. was greater. The optimum potential range for the floatation of chalcopyrite in collectorless solution at pH value of 6.97 was between OCP (0.165V) and 0.35V.`

Jan 1, 2015

By Tang Chaobo

According to the principles of simultaneous chemical equilibrium and electronic charge neutrality, the system of Mg(II)-NH3-CO32--SO42--H2O at 25°C has been thermodynamically analyzed. And the rule of solubility of MgCO3(s) in the system is discovered, the high dissolution field of MgCO3(s) is discovered too. Furthermore, the solubility of MgCO3(s) is increased with the increase of the concentration of SO42-, but it is decreased first then increased with the increase of the concentration of all the CO32- and the total concentration of ammonia and ammonium, and decreased with the value of pH being higher. Those results will has important significance on prepare magnesium chemical products and other salts carbonate that are strict with the content of magnesium with carburization method.

Jan 1, 2006

By Fatma Arslan

Alada (Kayseri-Turkey) lead-zinc sulfide-oxide ores contain 10.17% Pb, 10.98 %Zn, 164 g/t Cd and 57 g/t Ag. During the laboratory scale flotation tests of these ores, it was found that almost all zinc was remained in the tailings that contain 12.31% Zn, 1.35%Pb, 198.3 g/t Cd, and 22.3%Fe. Three different methods were studied such as basic (NaOH) leaching, roasting+acidic (H2SO4) leaching and direct acidic (H2SO4) leaching for recovering metals that these tailings contain. In the direct acidic leaching, which gave the best results, dissolution efficiencies of 91.5% zinc, 78.2% cadmium, and 14.3% iron were reached at the optimum leaching conditions while Pb remained in the leach residues and the acid consumption was 422.3 kg/ton of tailings.

Jan 1, 2006

By Itavahn Alves da Silva, Jose Dimas de Arruda, Amanda Aparecida Fátima Arruda, da Silva de Souza, Carlos Antonio da Silva, Varadarajan Seshadri, Samuel

The knowledge of the flow field inside a continuous casting mold is essential to improve operational efficiency of the process and also to achieve better inclusion control. Physical modeling, PIV technique and CFD have been employed to assess the velocity distribution in the metal- slag interface region in a slab mold. The analysis of results shows how higher casting velocity and lower immersion depth of submerged nozzle can lead to higher turbulence in the slag-metal interface. The effects of density difference between slag and metal and interfacial tension between the phases have been highlighted.

Jan 1, 2016

By Gerald M. Ellis

Exploration for gold .deposits on Hispaniola has taken place sporadically over the years but has expanded in the past decade. There are veintype, disseminated, alluvial and elluvial deposits. Investigations were previously undertaken in Haiti by combined Haitian, Bureau of Mines, and UN geological teams at Grand Bois Limbe(Milot) and Cap Coq areas. Later studies were conducted at the Miches and Moncion districts. Gold occurrences were reported in quartz, silicic-barite veins and gossans. An important deposit ?at Pueblo Viejo is? a disseminated type where extraction is taking place in the oxidized zone. Exploration by Japanese and West German firms with local geologists are described in this paper together with Pueblo Viejo, Miches, Restauracion, Milot, and Meme ?areas where occurrences are known. Copper deposits with associated gold va1ues are also described. These include vein deposits in Central Cordillera and disseminated deposits at Terrier Rouge and Blondin.

Jan 1, 1989

By E. Anelli

Based on experimental continuous cooling transformation (CCT) diagrams, an artificial neural network has been trained to predict the amount of microsturctural constituents and hardness resulting from and controlled cooling at rates from 150 to 0.015 K/s. It can be applied to quenching and normalizing processes of low-alloy steels with 0.05-0.30 C% and 0.4-2.0% Mn -with possible microalloying additions. Examples of the good predictive capabilities about 15 Vickers standard deviation for hardness and a few percent for volume fraction of phases) are reported&apos; Keywords: Austenite decomposition, low. And medium-carbon steels, artificial neural networks

Jan 1, 2003

By V. Kamavaram

Ionic liquids are novel salts used as potential non-aqueous electrolytes for aluminum electrolysis at low temperatures. In the current research di-alkylimidazolium chloride ionic liquids such as 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) and 1-hexyl-3-methylimidazolium chloride ([HMIM]Cl) were investigated for aluminum electrolysis. Melt formed by mixing ionic liquid with AlCl3 is termed as chloroaluminate and is composed of several polymeric chloroaluminate anions. Ionic liquids are studied as electrolytes for aluminum electrowinning and electrorefining of aluminum based materials (A356, A360, & Al-MMC) at low temperatures. Mechanism of aluminum electrodeposition in these chloroaluminate ionic liquid electrolytes was investigated using electroanalytical techniques such as cyclic-voltammetry and chronoamperometry. Aluminum electrodeposition on pure copper substrate in AlCl3-[BMIM]Cl (1.5:1.0) electrolyte at 30°C melts was found to be quasi-reversible process with a charge transfer coefficient ( of 0.40. Chronoamperograms obtained at different voltages in the range (-0.1 to -1.0 V) revealed that the initial stages of aluminum deposition in AlCl3-[BMIM]Cl melts was instantaneous nucleation followed by diffusion controlled growth of three-dimensional aluminum nuclei. The diffusion coefficient of electroactive species Al2Cl7¯ in AlCl3-[BMIM]Cl melts was found to be 6.5×10-7 cm2 s-1 from Cottrell?s equation and 3.9×10-7 cm2 s-1 from the dimensionless current-time transients.

Jan 1, 2006

By J. W. Holzenthaler

Teams continue to play a major role at the Phelps Dodge Mining Company El Paso Operations, especially during the present time of low copper prices. The El Paso Operations&apos; teams have taken the initiative during this copper market downturn and have helped reduce operating costs significantly. Because of this, Phelps Dodge El Paso Operations has continued to grow within the team process by creating a total, non- exempt salaried workforce. In the last year alone, the El Paso Operations have implemented three major initiatives to accommodate the team process. The first was the creation of "guiding principles", a policies and procedures handbook. Second was the "zero and beyond" safety initiative. Third was team compensation. In addition, the Copper Products Company has now adopted a work-team environment, following the lead of the refinery.

Jan 1, 1999

By John Wallace, Chib Iheagwara

"Refinements in sensor design have produced low-cost rugged elements to act as loop coupled with stable detection hardware for eddy current measurement in difficult environments. This has allowed direct dimension gauging of nonferrous and ferrous products above the curie point for absolute dimensions and electrical conductivities independently. The software was developed for the analysis of electrical conductivity profiles in CZ silicon crystal growth, then refined for monitoring bar properties and tube properties. Since in most metal working operations, speeds at the minimum of a few hundred feet per minute are encountered the design of the gauge was optimized for a rapid measurement. Independently extracting electrical conductivity provides data in some metal systems for determining the temperature of the monitored product.IntroductionThe primary reason for the use of eddy currents in gauging is that in hostile environments of metal working techniques such as laser gauging and ultrasonics are not always robust enough for in process measurements. Our goal is to use the technique of eddy current measurement as a quantitative control element in various hot and cold processing operations. Inspection in the early stages of metal and semiconductor processing is usually too costly to introduce in a well developed process and these tools are usually only employed in process development. Until recently there has been no efficient general analysis to allow real time measurements in the cylindrical and the probe geometry that could separate dimensional changes from material property changes both which effect the eddy current response. The basis for these measurements is that forward electromagnetic problem for conductors can be solved exactly for the test geometry which allows an inverse analysis to be made by relaxing the dimensions and conductivity to values which reproduce the measured response[!]. This transformation is based on analysis developed in Robert Siegfried' s thesis and was explored both by modeling and by physical measurement. This analysis was extended over the last few years to allow a more compact data set to be used to exact physical properties. The main result was that the technique would work on high ·quality physical data on as little as three test frequencies with the penalty being that the analysis is computational intensive. The main result of this work was that a quantitative inverse analysis of eddy current response would allow a general instrument to be used for a variety of measurements rather than being tailored for a specific measurement on a specific material test geometry. The development of these instruments has progressed over the last ten years for monitoring real time solidification, crystal growth[2] and hot seamless tube forming where the use of standards in traditional eddy current is limiting. The specific instrument design was dictated by the requirements of the algorithm for both frequency selection and levels of systematic noise that could be tolerated. Because the data is need for real time information this dictated that the system be a parallel multifrequency eddy current instrument feeding the same sensor. The sensor have to be simple and robust and usually a single loop or several loop of heat resistant wire or tube. This presentation is about using inversion of multifrequency eddy current data in real time to produce dimensional and property data on cylindrical conductors and planar conductors in real time. The object of the measurements is to produce dimensional outputs on measurements of conducting material without having to establish a detailed standard for each material or size tested. The dimensional measurements using eddy currents is complicated by material variations in conductivity due to temperature and composition. Those variations that are not geometric are often not of critical interest and complicate the measurement. The dimensional changes are often of more importance"

Jan 1, 1997