Search Documents

By Christian Hecker

An Eh-pH electrochemical sensor developed for on-line pH and redox potentials copper sulphide flotation process control was studied. The electrochemical sensor cell includes two metallic platinum electrodes, a metallic antimony electrode and a high impedance reference cell which are polarized with a potentiostat. For pH and redox potential determinations, the Sb and platinum electrode potentials are measured, respectively, against the polarized electrochemical reference system. The behaviour of this electrode configuration has been investigated in a laboratory scale. An electrochemical sensor device has been succesfully installed and checked in El Teninte Colon Concentrator's SAG line feeding the copper flotation rougher circuit.

Jan 1, 1999

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By Tae-Hyun Kim, Shun Myung Shin, Jin-gu Kang, Jeong-Soo Sohn

We investigated about synthesis of Mn-Zn ferrite with spinel structure using sulfuric acid leaching solution of mixed spent zinc-carbon batteries and spent alkaline batteries. The waste batteries were prepared by physical treatment such as crushing, magnetic separation, and screening. After screening, the crushed batteries were separated to +8 mesh and -8 mesh powder. Among these, under 8 mesh powder was selected for leaching test. The leaching test was investigated at 2 M H2SO4, 4 vol.% H2O2, reaction temperature 60 ?, agitation speed 250 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of zinc, manganese and iron were 99.0%, 98.9%, 58.5%, respectively. For co-precipitation of zinc, manganese and iron, 5M NaOH solution was used for pH control. Then in order to synthesize Mn-Zn ferrite powder, it was investigated according to reaction temperature, agitation speed and O2 partial pressure. We could synthesize about 20 nm of Mn-Zn ferrite with spinel structure.

Jan 1, 2008

By Tateo Usui

In the course of carbonization of coal under a rising temperature condition, volatile matter (V.M.) is released. The kind and amount of V.M. released depend on the kind of coal. Components of V.M. are tar, hydrocarbons (CH4, C2H4, C2H6, C3H8), CO, CO2 and H2, which are released in this order as a function of carbonization temperature. When the carbonization of coal under a rising temperature condition is interrupted at a certain temperature, TC, max, semi-coal-char with residual V.M. is obtained. If some optimum interruption-temperature is chosen, small but most suitable amount of V.M., namely H2, is retained. When the semi-coal-char thus obtained is heated again under the same rising temperature conditions but up to more than TC, max (1), the residual V.M. is released from just around TC, max (1). We propose novel iron ore agglomerate bearing such semi-coal-char with some strength. While simple iron ore agglomerate bearing coal char will start the reduction reaction as solid-solid reaction at somewhat higher temperature, the proposed one will start the reduction reaction as gas-solid reaction at somewhat lower temperature but a little higher than TC, max. Samples of semi-coal-char and novel iron ore agglomerate bearing such semi-coal-char have been prepared and evaluated.

Jan 1, 2006

By Jeffrey Shepherd, Scott R. Smith, Eduard Guerra

"Electrochemical and spectroscopic evidence for the dissolution of a Au electrode by meso-2,3- dimercaptosuccinic acid (DMSA) from an acidic LiCl04 electrolyte is presented. Near the potential of zero charge, DMSA was determined to form a stable layer on the metal surface but at more anodic polarizations, DMSA was displaced from the metal through an oxidative process. The anodic displacement of the layer from the electrode resulted in a small amount of Au that was detected in the electrolyte using atomic absorption analysis. The extent of Au dissolution, was monitored while holding the potential of the electrode for 24 hours at the thermodynamic Eo/H,O in LiCl04 electrolytes containing 10 mM DMSA. This routine resulted in detectable quantities of a soluble Au-DMSA complex in the electrolyte and the greatest leaching was observed at a pH = 2.0. At room temperature, the leaching rate was stable at 10.9 µg cm·2 hr·' however, upon increasing the temperature to 50.0°C, the rate of Au dissolution increased yielding an average rate of extraction of 40.1 µg cm·2 hr- 1. Interestingly, after the first 12 hours of leaching at 50.0°C, the leaching current decreased dramatically suggesting surface passivation which prevented further Au extraction. The implications of this process in the industrial leaching of Au will be discussed.IntroductionThe use of cyanide in the industrial process of leaching Au from ores has raised concerns regarding both operational safety and environmental issues surrounding the disposal of spent leaching eftluents in tailings ponds. Depending on the chemical nature of the processed ore, the spent solutions that are released into the tailings ponds can contain toxic cyanide, either dissolved or complexed with different metals and may pose serious risk to wildlife as well as freshwater contamination to nearby water systems. Because of these issues, some recent studies have focused on the exploration of more environmentally-friendly molecules to selectively leach Au with appropriate kinetics. However, to effectively leach Au into an aqueous solution, a suitable ligand that reacts to form a stable chemical bond with Au is needed to form soluble Au complexes that can be later recovered [I]. Recently several sulfur bearing alternatives have been shown to leach significant quantities of Au in aqueous solutions. These include thiourea [2], thiocyanate [3], and thiosulphate [4]. However, alkylthiols are also known to quickly form a stable covalent Au-S bond [5], but have been relatively understudied in term of their ability to leach Au in solution, even though some short chain thiols are water soluble and relatively nontoxic."

Jan 1, 2012

By Xin Wang, Hongmin Zhu, Shuqiang Jiao

"The behavior of electrochemically depositing silicon in a molten high-melting-point fluoride electrolyte was studied at 1300 °C. The cathodic product was characterized by XRD, SEM and EDS. Though the analysis of structure and composition of deposition, it could certify that silicon deposited on the Mo rod and alloyed with molybdenum. A series of tests had been performed on the cathodic behavior of Si4+ ions in BaF 2-CaF 2-Na2S iF 6 molten salt. The influence of electrochemical parameters on the cathodic deposition of silicon was also investigated. The electrochemical behavior of Si4+ ions in applied fluoride melts was observed to proceed according to one-step reaction.IntroductionGreenhouse warming has been a serious global issue. lt is increasingly urgent for clean and renewable energy. Effective utilization of clean and inexhaustible solar energy has become very important. Solar cell (especially poly-Si solar cell) production has significantly increased this decade, as there is a growing demand for clean energy. Since the early 1980s, the annual growth of the photovoltaic (PY) solar cell industry is more than 30%. More than 90% of the annual solar cell production is based on crystalline silicon wafers. This rapid growth leads to a shortage of silicon of the adequate quality and price for the continued growth of this industry [I , 2J. The most conunonly used technology to produce silicon is the so-called Siemens process. This technology, involves the forming of gaseous Si compounds such as trichlorosilane (SiHCli) or silane (SiH4) with subsequent thermal decomposition of these back to Si. This technology is associated with transformations from solid to gas, and then back to solid phase, which lead to high irreversible thermodynamic losses and subsequent high energy consumption, the energy cost being around 200kWh/kg Si [3l_ The purity of the material from this process is very high (9 to 11 N). In general, what is needed for solar cell purposes are reported to require 4 to 6 N quality. To promote continued growth of the silicon-based PY industry, there is need for a low-energy silicon production process which can produce large amounts of silicon with an acceptable quality and a lower price particularly."

Jan 1, 2012

By E. Allaine

Carbochlorination kinetics of pure MoO3, Nb2O5, Ta2O5 and V2O5, by Cl2+CO+N2 gas mixtures was investigated between 380 and 1000 °C. Standard free energy of carhochlorination reactions and phase stability diagrams of these refractory metal compounds were calculated. The influence of total gas flow rate, temperature, reactants partial pressures on the reactivity of these oxides were investigated. The apparent activation energies were found to be about 83, 75, 110 and 100 kJ/mole below 650°C for MoO3, Nb2O5, Ta2O5 and V2O5, respectively. Above this temperature, the Arrhenius plots exhibit a rate anomaly attributed to thermal decomposition of COCl2 and/or structural changes of these refractory metal oxides. The apparent reaction order of carbochlorination of these oxides with respect to Cl2+CO was determined. For these refractory metal oxides, the reaction rate was maximum for a Cl2/CO ratio of about 1 in the chlorinating gas mixture. Results of carbochlorination of these oxides are compared and discussed.

Jan 1, 1995

By Mark Jolly, Nasim Soleimanian

"During the last 20 years CFD (Computational Fluid Dynamics) has been used as a tool to aid furnace designers and manufacturers to improve energy efficiency and effectiveness of glass furnaces. However as the models are maturing the effect of feeding equipment used to push the raw material into the furnace has not been included in the process models. This paper investigates the effects of batch pattern in the melt space caused by charging equipment on the energy efficiency of the furnace focusing on the melting zone. A simple batch patterns sensitivity study has been performed using purpose built software (Glass Furnace Model-GFM). It is concluded that in order to further reduce the energy consumption of the furnace it is necessary to model the batch charging process in more detail to find more opportunities for improvement.Introduction Glass manufacturing is a conservative industry which applies to all the four major segments (float glass, container glass, fiberglass, and specialty glasses). Risks due to the high capital investment, very long service life of the furnaces, and the demand for high performance and quality from the outset translates into evolutionary progress rather than revolutionary. The main problem facing glass manufacturers are the financial cost of manufacture, its impact on the environment, and mounting pressure imposed by the authorities for greener manufacturing and reduction in emissions.The main energy intensive activities involved in continuous glass manufacturing are: the need for high temperature to create and maintain the viscous flow, homogenisation of glass melt (melt residence time), and maintaining the two to achieve continuous output of glass at the right quality. The high temperature and long duration of homogenisation has resulted in the design oflarge furnaces, which have high energy consumption, low specific performance, and high C02 emissions. As an example in the container glass sector the most efficient furnace has a specific primary energy consumption of 3.8 GJ /tonne of glass at a level of 50% cullet in the batch. Even very small improvements in efficiency by optimising operation would have a high impact [1-14]. Given the conservative nature of the industry and the costs involved in experimental data gathering, CFD modeling of the process has been used extensively during last two decades to not only improve our understanding of the process but also as a tool in predicting possible optimisation windows, e.g. Glass Furnace Model ( GFM), a commercially available piece of software that has been developed to optimise furnace operation."

Jan 1, 2013

By A. K. Riihimäki

The description deals with duplex stainless cast steels and austenitic high molybdenum steels used in pumps for severe condition service. The main modem nitrogen alloyed duplex cast steels are presented in the ASTM standard A-890. Two grades of high molybdenum austenitic stainless steels there are presented in ASTM A-744 (-96) standard i.e. CN-3MN and CK-3MCuN. The latest and most corrosion- resistant stainless steel grade is AVESTA 654 SMO?. Avesta Sheffield the trademark owner has granted Ahlstrom Pumps license to produce the material. This new stainless steel as pump material for severe service has improved properties in the hydrometallurgy and electrorefining processes of metal and especially in the copper industry compared to duplex stainless steels. The paper deals briefly with the foundry process to manufacture high alloy stainless steel pump castings. The AOD-method (AOD= Argon Oxygen Decarburization) is an important prerequisite for the melting of low carbon, high chromium and molybdenum alloyed nitrogen steels. The properties of these steels are included. The main topic is the corrosion resistance of the above-mentioned pump materials in severe service. Results of short-time erosion and corrosion tests are discussed and compared with the results of plant tests. Practical results of pump materials performance in severe service for the copper industry are given. The new high alloyed cast stainless steel (main elements; Cr-24%, Ni-22%, Mo-7,3% and N-0,5%) has shown improved corrosion and erosion properties as process pump material in several severe service applications e.g. in the metal industry.

Jan 1, 1999

By Dai Xi

In the present work, the viscosities of molten FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 semi-synthetic slags for nickel flash smelting were measured in the temperature range from 1473 to 1723K by a rotational viscometer. The ratio of Fe to Si02 was fixed at 1.2, calcium and magnesium oxide contents varied in the range from 2 to 8 mass% and 9 to 12 mass%, respectively. The results showed that silicate anions became smaller by increasing CaO content, which results in a decrease of the viscosity of the slag. In the case of MgO addition the viscosity behavior was complicated. At MgO content below II mass%, the viscosity increased with the increase of MgO at all temperatures tested. However, when the MgO content was above II mass%, the viscosity decreased slightly for FenO-MgO-CaO-SiO2 system. At higher MgO contents, low-viscosity slags can be obtained by adding CaO. At a given composition, .the viscosity decreased with increasing temperature. The higher the temperature, the more MgO can be added before saturation. The effect of Fe3O4 on the viscosity was quite significant. The viscosity of slag increased by 300mPa-s at 1573K when Fe3O4 content varied from 3 to 9 mass%. The viscosity values are presented as the functions of temperature and composition. A comparison between FenO-MgO-SiO2 and FenO-MgO-CaO-SiO2 systems is given in this study.

Jan 1, 2003

By M. F. El-Demerdash

The activity distribution diagrams for different species in aqueous systems are developed. Computational method may be considered as an extension of the Activity-Term method introduced by the authors to construct EH-pH diagrams. In the Activity-Term method, all activities of different species are evaluated before deciding the most stable one. In the present study, a factor is assumed to allow for the conservation of the element. At any point, the total concentration of all species should contain only the input m moles of the element (elements) considered. This approach is applied to Zn-, 5-, and Zn-S-H2O and activity distribution diagrams are plotted as a function of pH, at different potential levels and at different temperatures.

Jan 1, 1990

By Bogidar V. Mihaylov

Bacterial oxidation of a low-grade sulfide gold ore was investigated in order to enhance leaching of gold. The experiments were carried out in columns using mixed cultures of Thiobacillus ferrooxidansisolated from the ore. Fractions with different screen analyses were oxidized in two regimes - one pass of the solution and circulating, solution. Constant temperature and flow-rate of the percolating solution were maintained during the experiments. A correlation between the concentrations of copper and iron in the solution leaving the columns and pH and Eh values was observed. The effect of bacterial activity was proved by means of thiourea and cyanide leaching of the oxidized ore.

Jan 1, 1991

By A. E. Clark

Rare earth compounds are widely known as possessing many extraordinary magnetic properties. In this paper, we focus on the huge magnetically induced displacements (magnetostrictions) which characterize the compounds of terbium with iron (Terfenol). Materials prepared commercially by both free-standing-zone (FSZ) and modified Bridgman (MB) techniques have now become available in large sizes and shapes. Prior to the development of the Terfenol alloys, it was possible to achieve giant magnetostrictions only at cryogenic temperatures. In the cubic Laves phase TbFe2 compound, saturation strains exceed 3000 x 10-6 at room temperature and above. Large magnetization 'jumps' can occur, causing huge spontaneous magnetostrictions with small triggering magnetic fields.

Jan 1, 1992

By C. Lupi

Zinc chloride electrowinning presents difficulties in obtaining smooth, compact and dendrite free deposits with a high current efficiency due to the presence of undesirable metal ions. However, it is hard to define a level of impurities tolerable in zinc deposition, and despite a lot of research in this field, the reaction mechanisms of the undesired metal ions are still not clearly understood. In this study, the influence of Fe, Cd, Co, Ni and Cu additions were investigated, as well as their synergic effect on the zinc electrodeposition process from chloride electrolytes and on the obtained deposit morphology. The tests were all performed in presence of TBACl which reduces the harmful effect of such impurities on the zinc reduction.

Jan 1, 2003

By Batric Pesic

A hydrometallurgical process for recovery of Zn and Mn from Bunker Hill Water Treatment Plant sludge was developed. The process is unique because it treats an unusual combination of metals, Zn and Mn. Another non-standard feature of the process is that leaching takes place with ~S04 in the presence of a reductant (SO2). Zn and Mn are recovered simultaneously by electrowinning, Zn on a cathode and Mn on an anode, as MnO2 The major purpose of the process is to detoxify the sludge by removing toxic heavy metals. The recovered metal values could be marketed to offset the overall costs of water and sludge processing. This work is presented in two separate parts, 1. Leaching and Solution Purification, and II. Electrowinning. This paper covers only the first part of the hydrometallurgical process: Leaching and Solution Purification. Initially, the paper briefly discusses the history of the pollution problem at the Bunker Hill Superfund Site, the origin of heavy metals in the mine waters, and the development and use of the water treatment plant. The leaching of sludge was examined as a function of the following parameters: constant vs. initial pH, initial vs. delayed addition of SO2, temperature, and pulp density. It was found that leaching with H2SO4 at pH 2.0 for 15 minutes (at 60°C), followed by S02 addition for another 15 minutes, could completely dissolve Zn and Mn. Solution purifIcation was done in three stages. In the first stage iron was removed by adjustment of pH (to pH 5.0) and oxidation offerrous to ferric iron (with H2O2). In the second stage, Cu and Cd were removed by Zn dust cementation. Finally, Co and Ni were precipitated with the organic reagents 1-2 nitroso-naphthol and nitroso, respectively. Electrowinning of Zn and Mn is discussed separately in Part II of this paper.

Jan 1, 1996

By Donna M. Noel

Bacterial strains have been cultivated from solids previously exposed to cyanide that will tolerate 300 ppm sodium cyanide under anaerobic conditions. In selected solid samples, these bacteria have been shown to reduce the level of cyanide from approximately 300 ppm to essentially zero in about 50 days under anaerobic conditions. Various media were investigated, and the nutrients providing maximal growth were ?established .. Degradation of cyanide in sterilized solids was determined for comparison with degradation obtained in bioactive solids. All experiments were conducted at ambient temperature and initial pH of approximately 10.5.

Jan 1, 1991

By V. Ramachandran

In view of the increasing environmental regulations that have been promulgated in the last 30 years, non-ferrous smelters and refineries have learnt to handle effectively the process waste streams that need to be bled from the system for impurities' control. The cations of concern are copper, lead, zinc, cadmium, mercury, thallium, nickel, silver, sodium and potassium. Anionic species of arsenic and selenium also need to be addressed, Sulfates and chlorides-not a major concern at present-have come under scrutiny in the recent past. The current paper reviews several treatment options with reference to a) types of waste streams processed b)process chemistry c )discharge options and recovery of treated water and d) sludge disposal. The long term goal of any smelter and/or refinery should be to achieve zero liquid discharge from the plant. Methods to obtain zero discharge are discussed.

Jan 1, 2003

By Yasuhiro Konishi, Kazunari Mizoe

"This paper describes a new processing of ultrafine, magnetic ferrites from sulfuric acid pickling solution in steel industry. In the ferrite processing, the iron (II) in the pickling solution was first oxidized to iron (III) by using the acidophilic thennophile Acidianus brierleyi. The bio-oxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic solution of tertiary aliphatic monocarboxylic acid. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were hydrolyzed and precipitated ultrafine particles of crystalline ferrites at l90°C and l. 3 MPa for 20 min.IntroductionHot-rolled steel sheet has always a layer of oxides on its surface. The oxide layer arises as scale in hot rolling processes in steel industry, and the scale consists of the three iron oxides such as hematite Fez03, magnetite Fep4, and wustite FeO. Pickling removes chemically the scale layer that adheres to the steel surface. For normal steels, pickling is carried out in 15-20% hydrochloric acid at 60-70°C or in 20-25% sulfuric acid at 95-100°C. When steel is pickled with sulfuric acid, the scale oxides dissolve to give iron (II) sulfate.Spent pickling solutions are hazardous wastes containing a large amount of dissolved iron (II) and sulfuric acid, e.g., about 40 kg/m3 of dissolved iron (II) at pH 0. In typical commercial processes, spent pickling solution is usually cooled evaporatively to 5°C, and then to 0°C to crystallize iron (II) sulfate as its heptahydrate. After the crystallization operation, the sulfuric acid can be reused in the pickling operation.In this paper we describes a new processing of ultrafine, magnetic ferrite from sulfuric acid pickling solution, in order to recover dissolved iron (II) in the form of a valuable product. In the ferrite processing, the iron (III) was first supplied by the microbial oxidation of iron (II) in the pickling solution, and then the biooxidized pickling solution was treated with solvent extraction to separate the iron (III) into the organic carboxylate solution. After that, the carboxylate solutions of iron (III) and other metal (cobalt) were precipitated crystalline ferrites under hydrothermal conditions."

Jan 1, 2000

By C. R. Palmer

The Bureau of Mines investigated the use of ion-exchange technology for the recovery of precious metals from cyanide leach and spent electrolytic solutions. This research included adsorption of gold and silver on both weak-and strong-base anion-exchange resins. The effects of nickel, mercury. and iron on precious metal loading of strong-base resins were also determined. Due to the nonselectlvity of strong-base resins, selective elution also was investigated. Both commercially available and experimental weak-base anion-exchange resins were tested. None of the commercial weak-base resins tested were suitable for a caustic-cyanide system owing to their low recovery of precious metals at pH 10 or above; however, three experimental resins have possible application. Continuous tests conducted with mill cyanide solution in a multicompartmented ion-exchange column using strong-base anion-exchange resins adsorbed nearly 100 pct of the precious metals as well as the iron and nickel. During the elution of this loaded resin the iron was first removed with NaCI plus NaOH; then nickel with dilute H2S04 or HCl; finally gold and silver with thiourea in dilute HCl.

Jan 1, 1988

By A. Ohno

"A new near net shape casting process, OHNO Continuous Casting (OCC), has been recently developed. In this process, molten metal is fed into a heated mold maintained at a temperature above the solidification temperature of the metal being cast. Solidification begins from the central core of the casting rather than the wall of the mold. With the heated mold, the formation of crystals on the mold wall is prevented and solidification occurs out of contact with the mold surface. This produces near net shaped products with smooth, mirror-like surfaces and unidirectional grain structures free from cavities, porosity and segregation. Any crystals formed at the beginning of solidification decrease in number as solidification progresses and eventually a single crystal product is obtained. This process is applicable to any metal alloys, converting them into new materials with superior properties and quality.IntroductionAs a result of growing technical demands for more advanced and diversified materials, the OHNO Continuous Casting (OCC) technology has found many new applications in industry. Considerable interest in the process has been shown in Japan and other countries because of its distinct ability to:produce a single crystal, (1)produce a remarkably clean cast surface without a witness mark,provide extremely good ductility,and reduce casting defects and segregation.This paper provides an overview of the principle of the OCC process and describes the remarkable characteristics of the material produced by this method."

Jan 1, 1988