Search Documents

By Pietro Navarra

Cooling of critical furnace equipment to produce freeze lining is of particular interest as many metallurgical processes are intensified while attempting to prolong campaign life. This idea was combined with high-capacity heat pipes in the design of a copper slag launder. The design methodology of the launder and heat pipe cooling system is examined in this paper. With reliable material properties and operating conditions, CFD was used to quantitatively predict the skull thickness and the corresponding heat load applied to the slag launder. The operational limitations of heat pipe technology were considered and an appropriate cooling system was incorporated into the model. Parametric modeling was used to simulate several launder and heat pipe configurations. The generated results were then used to optimize the design of the launder, which was built and tested in August of 2005. The experimental performance of the cooling system is evaluated and compared with the model results.

Jan 1, 2006

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By Sergio Neves Monteiro

The efficiency by which an applied load is transmitted through the composite structure depends on the strength of the interface between the matrix and the second phase. In fiber reinforced composites, the interfacial shear stress plays a major role in the composite capacity to support the applied load. This interfacial stress can be obtained by means of pullout tests using the fiber embedded to a certain length in a socket of the matrix material. In the present work, pullout tests were performed to evaluate the interfacial shear stress of ramie, a relatively strong natural fiber, reinforcing polyester matrix composites. The general result permitted to calculate a critical length for the ramie fiber embedded in polyester resin. From this critical length, the value of the interfacial shear stress was calculated. An interpretation of this result together with SEM observation displayed a relatively weak bond between the ramie fiber and the polyester matrix.

Jan 1, 2010

By Z. Sun

Imposing a strong magnetic field is considered to be an attractive method to prepare materials with aligned or textured structures due to its intrinsic properties, e.g. non-contact and easily controllable. However, the nature of the strong magnetic field effect still remains unclear and further research is needed. In the present paper, the effect of a strong magnetic field on the solidification of a hypereutectic Al-Cu alloy was investigated. After magnetic field treatment, the primary phase was aligned parallel to the magnetic field direction. Meanwhile, the eutectic micro-structural constituent became elongated and thinner. A theoretical analysis was conducted to have a better understanding of the phenomena. During solidification, the magnetic Faraday and dipole-dipole interaction forces are considered to decrease the solute pile-up in front of the solid-liquid interface and modify the eutectic cell formation. The alignment of the phase is due to the shape magnetic anisotropy and crystal magnetic anisotropy.

Jan 1, 2010

By A. R. Kiani-Rashid

Controlled graphitization has become known as a practical method for improvement of wear resistance and machining properties in steels. In this paper, the effect of heat treatment on microstructure of CK45 steel has been investigated. Austenitising was carried out at 920°C for 5 hours. Besides, isothermal transformation was conducted at 750°C in the time range of 1-20 hours. The microstructure of the steel considerably changes by this heat treatment process which exhibits the effects of temperature, appropriate austenitising duration and isothermal transformation. Conducted experiments show a suitable distribution of semi-spherical graphite particles especially on the surface of the steel. Also, analyses demonstrate that the amount of formed graphite in the austenitising temperature 920°C is more than graphite in single heat treatment temperature of 750°C.

Jan 1, 2010

By Guo Xueyi

The method of Substance Flow Analysis (abbreviated as SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level. In this work the flow of lead in China, 2006, was traced within the STAF model, and the situation of production, consumption and recycling of lead resources in China were introduced. The SFA is performed on lead flows during its one year life cycle in detail. As one of the biggest producer and consumer of lead in the world, China is facing a problem depletion of lead resources. How to increase the resource efficiency is a significant issue for lead industry of China. Based on the result, several suggestions were proposed in the paper, aiming to contribute important reference information for the industrial metabolism and resource management and recycling of lead industry in China.

Jan 1, 2009

By A. S. Usrnani

Due to both turbulence and the highly variable geometry of castings, a realistic numerical simulation of the metal flow is prohibitvely expensive with current technology. However, when the chief purpose is to achieve realistic thermal fields a precise How simulation is not necessarily required. In this paper we assume a laminar flow regime and obtain the flow field by solving the incompressible Navier-Stokes Equations using a velocity-pressure segregated semi-implicit finite element method. The free metal surface is predicted by advecting a pseudo-concentration function via the computed How field. This involves an explicit finite element solution of a pure advection equation. The thermal field is calculated by solving the convective-diffusive energy equation by an explicit finite element method using the computed flow field and the location of the free surface. All the advection terms are discretized using a Taylor-Galerkin method. The interface between the metal and mould is modelled using special interface elements. The model is demonstrated by solving practical example problems. The results show that a sharp thermal front is maintained during the course of filling without excessive diffusion. The heat diffusion in the mould can be controlled by varying the metal mould heat transfer coefficient.

Jan 1, 1994

By B. B. Agrawal

Iron ore fines is an area of concern in India. A possible avenue is to use these fines for sponge ironmaking. Work has been carried out to pelletize these fines with coal and a suitable binder, and cure them in ambient atmosphere to retain in-situ reductant. Pellets were characterized for physical strength and metallisation. Critical factors were granulometry was percentage of coal & binder. In laboratory tests, pellets got metallized faster compared to lump ore. Large-scale trials were conducted in a 12-meter long rotary kiln plant. For 90% metallization, required residence time was only 60 minutes against 240 minutes for lump ore. Coal requirement also decreased. Investigations established the fast reduction nature of pellets. This is due to reduction-reactions occurring simultaneously at many sited within the composite pellets, in addition to the diffusion of reducing gases from the surface of the pellets to its core. The developed process is a value addition in the conventional pelletmaking and is environment-friendly also.

Jan 1, 2006

By Kymberley Worrell

The Cripple Creek and Victor Gold Mine was acquired by Newmont in August 2015. The high grade flotation mill project was commissioned in February 2014. The mill to date has been throughput limited due to mechanical and design issues. In order to create the most value from a throughput limited plant a campaign to provide timely ore characterization was undertaken. A diagnostic leach methodology was developed to determine gold associations by ore type. The resulting associations were then used to characterize feed blend; gold losses and optimize gold production. The diagnostic methodology is presented along with discussion on flotation implications.

By J. R. Donald

For processing copper, continuous converting has been successfully employed in a variety of locations, but for nickel, there has yet to be a successful commercial implementation of continuous converting technology. At Inco?s Copper Cliff smelter, there are specific requirements for the production of Bessemer matte relating to downstream processing that makes continuous converting for nickel mattes even more challenging. The nickel carbonyl refineries require very low iron levels in the matte, and the sulphur deficiency must be carefully controlled such that the appropriate quantity of PGM-rich metallics are produced from matte separation. The present paper outlines continuous converter technologies that have been implemented in copper, and evaluates their potential for nickel converting. The challenges of producing a Bessemer matte to the required specifications are discussed. The economic and environmental driving forces, and the challenges of justifying a novel technology in place of productive existing equipment, are discussed.

Jan 1, 2005

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010

By Jun Lu, Min Chen, Wei-jian Su, Jian-zhong Luo, Yu-tao Lei

"In the case of treating phosphatizing wastewater containing zinc, zinc had an impact on the solution chemistry, especially on pH. Fe2(SO4)3 and CaCl2 were used as precipitators to remove phosphate from zincic phosphatizing wastewater and the optimum pH was investigated. Zinc ion had a significant effect on the optimum pH. The optimum pH ranges were 12.10(inlet concentration of 15.67mg/L, outlet concentration of 9.53mg/L), 3.04-5.50(inlet concentration of 11.97mg/L, outlet concentration of 0.44-0.26mg/L), and more than 10.72(inlet concentration of 12.24mg/L, outlet concentration of less than 0.47mg/L) under the conditions without precipitator, with Fe2(SO4)3 and with CaCl2 respectively.Introduction Phosphate coating is commonly used for protective coating of machine elements. Including oil removal by caustic washing, rust removal by acid washing, phosphatization and inactivation, the phosphatization process produces wastewater containing inorganic salt of high concentration, especially the phosphate, beyond the environmental standards and polluting environment seriously. What’s more, the wastewater from zincic phosphatizing technology also contains another pollutant, zinc. At present, Chemical Precipitation (CP) and Biological Nutrient Removal (BNR) are two of most common technologies of phosphate removal. BNR, such as A/O, A2/O and UCT technology, is suited for wastewater containing organ phosphorus of low concentration and CP for wastewater with phosphate of high concentration [1]. Researches on CP treating wastewater containing phosphate of high concentration, mainly focus on adding quantity of precipitators[2-5] and coagulants[2-4] and the choice of technologies[3-9]."

Jan 1, 2008

The mineralogy of the platinum group metals is fairly complex, and it is therefore not surprising that the different minerals have variable responses to metallurgical processes, in particular, flotation and leaching. The PLATSOL® leach process was developed to extract simultaneously base metals, gold and platinum group metals from various materials. Extensive research has indicated that most PGM?s were amenable to the PLATSOL process, with the notable exception of cooperite PtS. Further work showed that a thermal pretreatment at 500-700ºC transformed the structure of the cooperite and similar refractory minerals (Pt,Pd)S into Pt metal and Pt-Pd alloys that responded well to the PLATSOL® process. Examples are presented of the mineralogy of PGM concentrates as produced, in the residue from the PLATSOL® leach and after thermal pretreatment.

Jan 1, 2006

By Run Huang, Xuewei Lv, Songli Liu, Chenguang Bai

"Titanium alloy was prepared from titania-bearing blast furnace slag (Ti-BF slag) by aluminothermic process in an induction furnace. The effects of aluminum amount on the titanium silicon yield and titanium recovery ratio were studied. The phase transformation and chemical composition of the prepared alloy were investigated by X-ray diffractometry (XRD) and X-ray fluorescence (XRF) respectively. It was found that the mass fraction of silicon and aluminum increased with increasing the aluminum amount, however, the mass fraction of titanium increased first and then decreased with increasing the aluminum amount. Furthermore, both the titanium alloy yield and titanium recovery ratio increased with the increase of aluminum amount. The main phases of the alloy were TixSiy and AlTi3. The titanium alloy samples prepared in various conditions had a composition (wt.%): 38–50% Ti, 29-34% Si, 4-11 Al%, 1.6-2.2 Mn%.IntroductionPanzhihua and Xichang regions in the southwest of China are rich in vanadium-titanium magnetite containing iron, vanadium, titanium and gangue. According to the characteristics of the resource, iron and vanadium are successfully recovered with a blast furnace process and a converter process. However, most content of titanium are entered in the blast furnace slag with TiO2 22% -26% and metallic Fe 2%–6% called Ti-BF slag. Due to the dispersed distribution of Ti in various fine grained mineral phases with a complex combination between Ca, Al and Si, it is difficult to recover the Ti components[1]. This slag is generated at a current rate of 3.6 million tons per year, which adds to the existing 70 million tons of slag produced so far[2]. The slag has had to be piled as large as the mountains, which not only waste of resources but also cause a pollution of the environment. Therefore, the study of integrated utilizing Ti-BF slag has become very significant."

Jan 1, 2012

By Tiebao Yang

In high pressure die casting processes, a die plays a critical role in removing heat from the molten metal during the cavity filling and solidification stages. Proper control of die temperature is essential for producing superior quality components and yielding high production rates. This paper proposes a local temperature control scheme for die thermal management based on a computerized intelligent real-time monitoring and control system (IRMCS). In this scheme, cooling water lines are controlled by a pump and solenoid valves. A controller is designed according to the law of die temperature fluctuations. The results obtained from the experiments carried out on a laboratory die casting process simulator indicate that the controller can limit the local die insert temperatures in a given band. Hence, the desired thermal pattern of the die insert becomes achievable.

Jan 1, 2006

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By WU Jian-hui

Keywords: metallic material; nickel powder; thermal decomposition; precursor; fibrillar powder; nanometer scale; passivation treatment The precursor thermal decomposition process of fibrillar nanometer scale nickel powder and passivation treatment of obtained powder are investigated, and the composition and morphology of the products are characterized by use of IR, TGA/DTA, XRD and SEM. The results show that the precursor morphology is a decisive factor to the product morphology of the nickel powder. The morphology of the product derived at low decomposing temperature is irregular. The nickel powders produced at the temperature higher than 480 coheres seriously. The product particles are reunited with the decomposition time prolong. The powder prepared under the optimal condition is fibrillar like woolen yarn; the grain diameter is less than 50nm.

Jan 1, 2005

By Tiezheng Li

Keywords: Laminate Composites; Mechanical Behavior; Damage Evolution The mechanical performance of Ti-6-4-Al3Ti metal-intermetallic laminate (MIL) composites synthesized by a reactive foil sintering technique was evaluated. Crack morphology of untested Ti-6-4-Al3Ti MIL composites has been characterized by optical microscopy. Mechanical tests were performed on Ti-Al3Ti metal-intermetallic laminate (MIL) composites and pure Al3Ti, and the principal mechanisms of damage initiation and accumulation were identified experimentally. The elastic properties and anisotropy of the laminates were calculated and successfully compared with Resonant Ultrasonic Spectroscopy (RUS) measurements. The effect of residual stress on the fracture toughness of the Ti-6-4-Al3Ti MIL composites was analyzed.

Jan 1, 2005

By Alexey Lozhko

The technical-and-economic furnace exploitation indices are considerably influenced by the system of heat utilization. In the situation of total output decrease works are forced to exploit furnaces at the partial loading, sometimes even at the idle running for the sake of steam production. The furnace exploitation in this regeme is known to cause the increase of the heat portion, taken away together with waste flue gases. The losses can be partially compensated at the expense of heat exchange efficiency development in the recuperator or heat-exchanger. One of the well-known methods, characterised by high efficiency and low expenditures is the intencification of the heat exchange process by the means of pulsation method.

Jan 1, 2006

By Jian Li, Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"A study of the coal-based direct reduction behaviors of composite binder magnetite pellets was carried out in a simulating coal-based grate-rotary kiln process. It is shown that preheated pellets possess much better reducibility than fired oxide pellets: 40 min are required for preheated pellets to reach over 90% metallization degree compared to 100 min for fired oxide pellets. The compressive strength of preheated pellets decreases dramatically at the earlier stage of reduction, climbs quickly after reducing for 30min and achieves a high value at the end of reduction. However, the compressive strength of metallized pellets from reducing of fired pellets is much lower, more cracks and fractures being formed. In the preheated pellets, crystallite of metal iron is coarse. In the oxide pellet, a large number of interconnected crystals of metal iron are formed inside pellets, and pellet structure is very compact.IntroductionDirectly reduced iron is an excellent feed in electric arc furnace (EAF) steelmaking, and possesses low tramp element content and steady component. It is generally preferred in the production of high quality steel [1-3]. Nearly 64.44 million tons of DRI were produced in 2009 over the world, over 80% of which were produced by gas-based processes, the left by coal-based processes. However, the DRI capacity was only 600 thousand tons in China in 2009. The EAF steel production has exceeded 40 million tons annually, and most of EAF operate on hot metal as feed [4]."

Jan 1, 2011