Search Documents

By Michael J. Nicol

The teaching of courses in geology, mining and extractive metallurgy in Australian universities is undergoing significant change largely as a result of the initiative taken by the Minerals Council of Australia (MCA). This has resulted in a major program aimed at developing national under- and postgraduate courses in selected areas with the aim of making these available to a consortium of participating universities. Murdoch University, together with the A J Parker CRC for Hydrometallurgy has been commissioned to develop the course in hydrometallurgy. Progress in the development of this course will be discussed in terms of overall philosophy, content and mode of delivery. Aspects of the extension to a Web-based course will also be summarized. Murdoch University has also established a hydrometallurgical pilot plant on the campus and the results of the first continuous operation for several months using under- and postgraduate students as operators will be discussed from the point of view of practical training and providing an interface with the local industry.

Jan 1, 2002

By K. J. Richards

The converting of copper mattes to blister copper has seen few technical advances since the introduction of batch furnaces using submerged tuyeres over a hundred years ago. The first side-blown converting vessel, operated by P. Manhes in 1882, was an offshoot of the 'Bessemer steelmaking process, and subsequent improvements in the conversion of molten mattes resulted In the Peirce-Smith converter, still the Industry standard today. While Peirce-Smith' converting has served the industry well since the early 1900!s, increasingly stringent environmental regulations, burgeoning energy costs, and a trend toward continuous processing have set the stage for a major improvement in this area of copper production. In contrast to a growing number of approaches for continuous converting using molten copper mattes, Kennecott is developing a process for treatment of solidified matte which allows improved' control, higher oxygen enrichment and a separation or decoupling of smelting and converting operations not possible with the other converting technologies. The new process known as Solid Matte Oxygen Converting, or SMOC, eliminates the need for molten matte transfers, minimizes fugitive emissions, and produces high strength SO2 off gases which substantially reduce offgas handling requirements. The SMOC process, despite additional matte solidification and size reduction steps, offers both capital and operating cost advantages for new smelters and the upgrading of existing plants, when compared with conventional converting technologies. Capital cost reductions of up to 35% in converting, gas handling, and sulfur fixation are indicated. Kennecott has successfully tested the new process concept and continued' development work is now under way to commercialize the technology. This paper reviews the limitations of batch copper converting with emphasis on the need for a continuous process, previous industry approaches to continuous converting of molten mattes, and the new Kennecott development.

Jan 1, 1983

By Michael B. Tessieri

With the increasing environmental demands and higher fuel efficiency standards on auto manufacturers, the use of aluminum in automotive applications is expected to show significant growth for the balance of this decade. Cast and wrought aluminum usage is reviewed by auto part, and alloy family for the year 2000 automobile. The analysis addresses the effect of this increased volume on the recycling infrastructure and identifies issues and opportunities, which will face the recycling industry.

Jan 1, 1995

By T. T. Chen, J. E. Dutrizac

Noranda Inc., CEZinc presently employs a cement-stabilization (jarofix) process to stabilize its jarosite residues for direct disposal. In this process, Portland cement partly decomposes Na-jarosite to form Ca6Fe2(SC>4)3(OH)i2.nH20, ferric hydroxide and sodium sulphate which further reacts to form gypsum; approximately one-third of the Na-jarosite reacts in the current commercial product. The cured jarofix products also contain minor amounts of various Ca-Al-Fe silicate-sulphate-hydrate phases and traces of calcite. Together with gypsum and a Ca-Fe sulphate phase, these species bond the various particles together, imparting mechanical strength and reducing the permeability. Water-soluble Zn and Mg are stabilized in the Ca-Al-Fe silicate-sulphate-hydrate phases. The freshly cured products usually contain small amounts of moisture and traces of residual Portland cement, which provides additional alkalinity for the neutralization of any residual acid species. Jarofix products stored for more than six years in the laboratory, after curing, are usually dry and exhibit the same micro-textures as those of the freshly cured products. However, the stored products are depleted in the Ca6Fe2(S04)3(OH)i2.nH20 and Portland cement phases, and are enriched in gypsum and calcite which reflects the highly alkaline environment of the jarofix products. The aged products also have increased amounts of the Ca-Al-Fe silicate-sulphate-hydrate phases which have elevated Zn and Mg contents. This implies a further immobilization of residual water-soluble Zn and Mg during stora

Jan 1, 2000

By François Tremblay

It is well known that removal of organic material such ,as Jacquer, paint, plastic prior to melting improves aluminum recovery. In addition to being an important economically, decoating of aluminum scrap has a positive impact on the environment, through better control of gaseous emissions. Most of the existing thermal decoaters for aluminum have been designed to operate with scrap containing a level of organic material lower than 10%. The main field of their present application is for recycling of used aluminum can, where levels of organic material are lower than 4%. Alcan has recently developed a new thermal decoating system in order to extend applications of this process to a much wider variety of aluminum scrap. The new decoater efficiently processes aluminum scrap with a level of organic material up to 50%. This new technology features the use of fluidized bed technology to thermally control the process. This innovative feature improves both performance and control over conventional delacquering systems based on hot air convection. This paper describes the basic principles of the technology and the design of the? first industrial unit commissioned by the Alcan Recycling plant in Shelbyville (TN) at the beginning of 1994. Typical applications and operating advantages are discussed.

Jan 1, 1995

By J. J. Kim

In a study of buildup in a green-feed reverberatory furnace, it was determined that approximately half of the crucible area has a moderate buildup of 25 in. or less, and that the area extending 45 f t from the burner end of the furnace has only a slight buildup. The false bottom, averaging 6 in. in thickness, was found to cover the entire crucible area. The stratification of Cr2O3, A12O3, and SiO2 occurs throughout the slag layer; this phenomenon is the principal reason for the formation of the false bottom in the green-feed reverberatory furnace. The false bottom is caused primarily by the settling of FeO*(A1,Cr),03 aggregates, which are derived mainly from returned converter slag. The false bottom can be transformed to a solid permanent buildup in the furnace, particularly when the matte is completely withdrawn. From the material balance of Al2O3 and Cr2O3 around the furnace, It is estimated that the average rate of aluminum chromite accumulation is approximately 0.3 ton per day or less.

Jan 1, 1976

By Lichao Ding, Chunhua Liu, Yunnen Chen

"In this paper the simulated acid magenta dye discoloring the reaction process was researched. The results showed that it attained highest decolorization efficiency for acidic magenta simulation dye wastewater when pH 9 and reaction time 10 min. With the initial dye wastewater concentration increased, the decolored rate decreased. The decolored rate in general kept a tendency to increase with the temperature increased. Kinetics researches showed that when pH 9, reaction temperature 20 and 35 ?, the decoloring reaction process for the dyes accorded with the First-order dynamic equation. The decoloring reaction rate constant was influenced by initial concentration of dye wastewater and temperature.1. IntroductionIn China, textile printing and dyeing industry is one of industrial departments which using more water and discharging more wastewater. There is about 7 billion tons of waste water discharge each year, of which 80% from the process of printing and dyeing. Being complex ingredients, high chroma, more toxic substances and severe environment pollution, the treatment of printing and dyeing wastewater becomes problem urgent to be resolved. The traditional treatment methods such as adsorption [1], coagulation [2], biochemical method [3,4], which has advantages of simple equipment, simple operation and mature process, but they can cause waste accumulation and secondary pollution [5,6].Magenta is a kind of organic compounds, which classified into acid and alkaline magenta. Considering the advantages of simple operation, low cost, simple experiment equipment and friendly to environment, acid magenta dyes wastewater was chose as object in this paper. Some parameters such as pH, contact time, temperature and the initial concentration on of simulative acid magenta dyes wastewater were studied."

Jan 1, 2012

By D. J. Senor

Closed chamber incineration (CCI) is a novel technique by which irradiated nuclear graphite may be destroyed without the risk of radioactive cation release into the environment. The process utilizes an enclosed combustion chamber coupled with molten carbonate fuel cells (MCFCs). The transport of cations is intrinsically suppressed by the MCFCs, such that only the combustion gases are conducted through for release to the environment. An example CCI design was developed which had as its goal the destruction of graphite fuel elements from the Fort St. Vrain reactor (FSVR). By employing CCI, the volume of high level waste from the FSVR will be reduced by approximately 87 percent. Additionally, the incineration process will convert the Sic coating on the FSVR fuel particles to SiO2, thus creating a form potentially suitable for direct incorporation in a vitrification process stream. The design is compact, efficient, and makes use of currently available technology.

Jan 1, 1994

By Ajit Kumar Jaiswal

"Electric Arc Furnace (EAF) being a power-intensive equipment, EAF based industries are highly dependent on scarce electric energy. This is the reason Government of India is highly concerned about this and laid emphasis on the conservation of electric energy.This paper highlights factors contributing to reduction in specific electric energy consumption in EAF and suggests measures not only for power saving, but also for productivity improvement. To name a few, these are proper sealing of furnace, introduction of oxy-fuel burners, foamy slag practice, increased usage of hot metal/DRI, post-combustion of CO gas for preheating of scrap, improved selection & design criteria of electrics, power demand management, and process automation. Few cases also have been cited, where the above measures have helped in reaping significant benefits.IntroductionFor a long time, Government of India had focused on increase in energy supply, in particular, through electricity generation. Now the emphasis of Government of India has shifted from electricity generation to its conservation for following two reasons:??Power plants have become very cost-intensive??By saving energy, more of it can be delivered at lower cost to the consumersPower generating units, transmission & distribution agencies as well as consumers all have roles to play in the area of energy conservation. By energy conservation, we mean curtailing energy requirement by reducing energy wastages and taking up measures to improve energy efficiency of electric equipment/appliances. In almost all cases, this would be economically beneficial.India’s cost-effective energy conservation potential has been estimated by the Planning Commission at 23 per cent of total commercial energy generated ?1?. A national movement for energy conservation can significantly reduce the need for fresh investment in energy supply systems in coming years. It is imperative that we make all-out effort to realize this potential. Whether a household or a factory, a small shop or a large commercial building, a farmer or an office worker, every user can and must make this effort for his own benefit and for the nation’s benefit as well."

Jan 1, 2009

By M. M. Kim

As-electrogalvanized coatings of pure Zn, Zn-11% Fe, and Zn-18% Fe coatings were characterized in terms of initial crystal structure and surface morphology. Samples were then subjected to heat treatments simulating the paint bake cycle of automobile manufacturers. Surface morphology changes were correlated with the process variables, and crystallo.graphic changes were interpreted by mapping heat treatment routes on the Fe-Zn phase diagram. The morphology of pure zinc electrogalvanized coatings with heat treatment from platelets to smeared platelets. The zn-11% Fe coating changes with heat treatment from tetrahedral nodules to a mixture of round and tetrahedral nodules, with the Zn-:18% Fe coating always having round nodules. Regarding crystal structure, a critical transformation time can be defined at any selected temperature, below which the crystal structure does not change. This temperature is related to iron content.

Jan 1, 1990

By Edouard Asselin, Guikuan Yue

"In the present study, electrochemical measurements, especially cathodic potentiodynamic polarization (CPC) and cyclic potentiodynamic polarization (CPP), have been employed to study the kinetics of ferric reduction on chalcopyrite in aqueous Fe( II )-Fe(III)-H2S04 solution at 25°C and 70 °C. Results from the calculation ofspeciation in the above solution reveal that, at both 25 °C and 70 °C, the real Fe3+/Fe2+ ratio is much lower than the nominal ratio, which leads to smaller values for the reversible potential of the ferric/ferrous couple based on the Nemst equation. Exchange current densities of the ferric/ferrous couple were obtained by extrapolating the cathodic linear Tafel line to the reversible potential and are on the order of 10-7·10-6 A/cm2 at 25°C and 10·6-10-5 A/cm2 at 70 °C, respectively. The transfer coefficients were about 0.35-0.38 at 25°C and 0.35-0.45 at 70 °C. Polarization plots of CPC and CPP under different nominal Fe3+/Fe2+ ratios are in good agreement at 25 ·c and at 70 °C. Based on the obtained exchange current densities, the rate constant k, was calculated and is on the order of 10-1 cm/s at 25 °C and 10 1 cm/s at 70 °C.IntroductionChalcopyrite is the most abundant copper mineral in nature, accounting for about 70% of copper reserves in the world [I]. In recent years, the metallurgical industry has been searching for a hydrometallurgical process as an alternative to pyrometallurgical treatment due to high emissions of S02 and capital costs associated with smelting. Activity in this area has increased recently due to some inherent advantages associated with hydrometallurgical processing, such as the possibility of treating low-grade ores (increasingly more abundant in the case of copper) and easier control of waste, with the attendant benefits to the environment [I]. Chalcopyrite is highly refractory under most hydrometallurgical conditions, owing to the formation of an anodic passivation layer on the chalcopyrite surface which renders the process kinetics very slow. Most of the currently proposed processes are based on sulfuric acid with ferric ions and/or dissolved oxygen as oxidants. Sulfuric acid is preferred over all other leaching reagents in terms of cost, environmental friendliness, and ease of its regeneration during electro-winning. Some of these processes have been piloted in attempts to implement these technologies on an industrial scale,"

Jan 1, 2012

By L. Sh. Tsemekhman

The results of laboratory, large-scale laboratory and commercial scale investigations regarding the process of slag melts cleaning by oxidizing-reduction gas mixtures with a wide range of Po2 and the use of matte of various compositions as an extracting phase are presented. The copper, nickel and cobalt behavior during the cleaning process has been studied based on SEM and x-ray Microprobe of the quenched slag melts. The general cleaning mechanisms have been found. On the basis of the obtained data the most efficient cleaning methods have been proposed.

Jan 1, 2003

By Jinfu Xu, Youqing Cao, Yuting Lv, Hang You, Peng Jiang

"In present work, we reported the fabrication of composites consisted of M42 powder metallurgy high speed steel and 45 steel at one step via spark plasma sintering (SPS) technology. The interface microstructure, compositions and microhardness with the interface forming mechanism were investigated. The results show that the morphology and microhardness within the M42/45 steel interfaces exhibit a gradient distribution. The interfaces possessed a transition layer up to 10.2 ?m with few distortions and microcracks. The formation of M42/45 steel interfaces were driven by both fusion and diffusion processes. The former one was primary at the early sintering process, while the later one becomes dominant over the followed sintering process.IntroductionPowder high-speed steels have been widely used in cutting tools, cold-hot tools and dies, as well as in cut materials and structure parts with wear resistance and high-temperature resistance, due to its high hardness, good wear resistance, desirable cutting toughness and favorable hot hardness [1-2]. For materials of some parts in practical production, not only the favorable toughness is required to resist the impact action, but also the high hardness and exceptional wear resistance are demanded. According to the functional requirements and working conditions, bimetal composite materials are prepared in a certain mode, proportion and distribution, by designing two metals with different chemical and physical properties [3-6]. Considering the composites exhibit different properties in different positions of the parts with a combination of the advantages of two metals, they can obtain enhanced properties that the single one can not achieve."

Jan 1, 2012

By Ryokichi Shimpo

Much amount of sludge is produced from the wastewater treatments in surface finishing industry. There are many problems for the abandonment of the sludge because of the high water content and heavy metals included. It is often observed that hexavalent chromium, which is toxic, is generated in the course of heat treatments of the sludge for reducing its amount by dispersing water. In this study, conditions of the sludge calcinations for reducing water contents have been examined. Maximum hexavalent chromium generation was observed in the temperature range around 773 K, at which most of the crystallization water decomposed from the sludge. When the heating temperature became higher than 1173 K, the amount of the hexavalent chromium extracted from the calcined sludge became as low as 10 mg/kg sludge. When the sludge was heated with iron oxides, FeO or Fe203, iron ferrite has been synthesized which may be used as a magnetic material. The amounts of hexavalent chromium generated in the heat treatment with iron oxides were not much different from those without iron oxides.

Jan 1, 2003

By James E. Simpson, Suresh V. Garimella, III de Groh

"An experimental and numerical study of the horizontal Bridgman growth of pure succinonitrile (SCN) and of a succinonitrile-1.0 mol. % acetone alloy (SCN-1.0 mol. % ACE) has been performed. Experiments at growth rates of 0, 2 and 40 µmis were investigated. The solid/liquid interface was stable (non-dendritic and non-cellular); however, it was not flat. Rather, it was significantly distorted by the influence of convection in the melt and, for the growth cases, by the moving temperature boundary conditions along the ampoule. For the alloy, the interface was determined to be unstable at growth rates greater than 2.8 µmis, but stable for the no-growth and 2 µmis growth cases. When compared to the pure SCN interface, the alloy interface forms closer to the cold zone,· indicating that the melting temperature has been suppressed by the addition of the alloying element. Two-dimensional computer simulations were performed for the no-growth case for both the pure and alloy materials. These simulations indicate that a primary longitudinal convective cell is formed in the melt. The maximum magnitude of velocity was calculated to be 1.515 mmls for pure SCN and 1. 724 mm/s for the alloy. The interface shape predicted by the computer simulation agrees well with the experimentally determined shape for the pure SCN case. In ongoing work, numerical simulations of the process during growth conditions are being performed.IntroductionIncreasingly, advanced materials used in the aerospace, automotive, optics and electronics fields require low levels of defects and high levels of solute uniformity. Directional solidification by the Bridgman process is widely used for synthesis of these high-quality materials. During Bridgman crystal growth, heat and mass transfer by both thermal and solutal gradient-driven convection and diffusion influence the shape of the solid/liquid interface and dopant segregation levels, and hence, directly determine the final crystal quality. Key process parameters include the applied furnace temperature distribution and rate of translation, ampoule properties and furnace orientation."

Jan 1, 1999

By Xiangwen Wang

Electrodeposition of lead metal from high purity brine electrolytes containing lead chloride (PbCI,) was conducted so as to assess the feasibility of electrowinning lead-metal directly from aqueous chloride electrolytes. Tests were performed at 65 and 80°C (338 and 353°K). Characteristic features of the deposits, on both lead and graphite substrates, were correlated to operating parameters associated with: electrolyte temperature, current density and total lead- concentration. Photomicrographs of these morphological features were obtained by use of Scanning Electron Microscopy (SEM).

Jan 1, 1993

By Terry Gerritsen

Electrode control systems regulate power by physically positioning electrodes. Due to the size and weight of the electrodes, this is a slow process where power fluctuations of less than a few seconds are not fully corrected. Nickel laterite AC furnaces operating in high voltage, shielded arc mode typically incur frequent power variations of approximately +I- 20% around the power set point. To provide enhanced power control, Hatch has recently supplied, at commercial scale, a thyristor-switched reactance system called an SPLC. The SPLC incorporates predictive control software to operate furnaces at the maximum transformer rating by reducing the large power swings experienced without the SPLC. The resulting higher average power enables higher production, without increasing transformer or power plant capacity. A 60 MW production version of the SPLC has been commissioned on Falconbridge Dominicans's laterite nickel furnace, yielding excellent results with a 3 to I reduction in power fluctuations. Keywords: SPLC, AC Power Supply, Electric Furnace

Jan 1, 2004

By G. B. Harris

Much has been written over the past decade concerning the disposal of arsenic from metallurgical processes. In Canada, there are proposed regulations which would classify arsenic in the Primary Group of twenty one persistent, toxic pollutants to be banned or phased out. Since many nickel and cobalt ores, not to mention those of copper, gold and uranium, contain significant amounts of arsenic, it is pertinent to assess the current state-of-the-art of its disposal. The literature is reviewed, and it is demonstrated that from a purely chemical point of view, the family of ferric arsenates largely immobilize arsenic. There is clear evidence from laboratory studies that both crystalline ferric arsenate (scorodite) and amorphous ferric arsenates in which the molar Fe/As ratio is at least three (Fe/As = 3) have very low arsenic solubility; plant data are given to support this. The debate over the long term stability of these compounds continues however; the evidence presented for long term stability and for compound breakdown is critically reviewed in the light? of the recent structural studies, and the role of base metals in these compounds evaluated. Finally, conclusions are drawn as to the viability of a purely chemical process for the long term disposal of arsenic from metallurgical processes.

Jan 1, 1993

By Ernest D. Mast

Noranda's Altonorte custom smelter, located in the 2nd region of Chile, 20 kilometres southeast of the city of Antofagasta, started operations in 1993. Presently, 1150 tonnes per day of new feed are smelted with an 85% sulphur capture. An oxy-fuel reverberatory furnace produces a 48%-55% copper matte that is treated in 13 ft. x 36 ft. (3..96m x 10.97m) Peirce-Smith converters (two hot and one blowing). Up to thirty percent of the new concentrate is smelted via dry concentrate injection into the converters. This paper reviews the development of the concentrate drying and injection system, and oxygen enrichment at Altonorte from start-up in 1995 to the present time. The relationship between oxygen enrichment and concentrate injection is reviewed from a theoretical and practical standpoint. Concentrate injection has improved the smelter's productivity and added flexibility to the operations. Due to the relatively high matte grades and the subsequent short converting times, maintaining consistent operations was difficult at times and the smelter has gone through a learning curve. Plant operating results and experiences are presented on the impact of concentrate injection in relation to: feed treatment, blowing times, revert generation, slag quality and refractory wear.

Jan 1, 1999

By Li Xi

This paper describes how a back-propagation neural network is built for predicting the properties of engineering materials from their other properties, compositions or processes. A predicted result of the impact toughness of a 12Cr-2Ni-1.5Mo stainless steel from its tempering temperature is presented. Furthermore, the combination of this neural network for prediction is able to supplement the unpredictability of the expert system outside its domain of expertise. An integrated system may perform more intelligently and solve more complex problems as well as human expert, in some case even better.

Jan 1, 1992