Search Documents

By Xun Hu, Jian Pan, Hongbin Yu, Deqing Zhu, Yanhong Luo

Lump ores are one kind of important burdens for blast furnace (BF), their metallurgical properties have significant influence on BF performance. In this paper, the relationships between the mineralogy of five natural lump ores and the metallurgical performance have been studied. The mineralogy study includes mineral compositions, microstructure and porosity, and the metallurgical performance covers reducibility index (RI), low-temperature reduction degradation index (RDI) and decrepitation index (DI). The results show that the complex lump containing hematite, and goethite has better overall metallurgical performance. For single lump, the RI of goetihte ores is higher, the RDI and the DI is strongly influenced by porosity. The hematite and magnetite ores have good anti-decrepitation and anti-RDI, but generally the RI is lower due to lower porosity, and the RI is related to the grain size, the smaller grain size is, the better reduction will be.

Jan 1, 2015

By Deborah A. Kopsick

Several minerals were observed and collected in a small gully originating from a weathered coal processing waste (gob) pile in Barton County, Missouri. The rapid alteration of these various minerals after collection suggested that they might represent a dehydration sequence. X-ray diffraction of the dehydrated and rehydrated minerals deposited on the gob pile indicated the presence of the monohydrate and heptahydrate forms of ferrous sulfate, szomolnokite and melanterite respectively. The occurrence of melanterite (FeSO4.7H2O), was limited to isolated areas of ponded water while szomolnokite (FeSO4.H2O), was associated with the outwash areas of the pile. Laboratory dehydration of melanterite collected at the gob pile revealed the formation of rozenite (FeSO4.4H2O), an intermediate form of ferrous sulfate. Szomolnokite was shown to be the stable form of these ferrous sulfates during these experiments while melanterite and rozenite were shown to alter readily. Chemical analysis of szomolnokite revealed enrichment in Fe, Mg, Zn, Cd, Cu and Mn relative to the chemical composition of the gob ad the lechate generated from the gob wastes. Although this gob pile had been weathering for more than 35 years, significant concentrations of trace metals were still being released from the pile through the generation of leachate and the formation of various soluble metal enriched ferrous sulfate minerals.

Jan 1, 1982

By Carvalho A. Felipe de

The search for environmentally friendly and cost-effective methods for gold extraction has been undertaken in order to provide alternatives to the use of cyanide leaching in the gold industry. Among such alternative reagents is the combination of chloride and hypochlorite ions due to their oxidation of metallic gold and its complexation. Therefore, the current work aims at investigating gold leaching from an oxidized material by means of a solution comprising calcium hypochlorite and sodium chlorite. The sample used in the current research contained 66.1% Fe2O3, 20.4%SiO2, and 35.7 g/t of Au. In addition, XRD and SEM-EDS analysis revealed iron oxide, quartz and muscovite as the main crystalline phases in the sample. For comparison purposes, cyanidation of the oxidized material resulted in 90% gold extraction in 24 h. The reference conditions for the leaching tests with the chlorite-hypochlorite system were: particle size −37 μm, solid/liquid ratio of 10% (w/v), 10 g/L NaCl, 10 g/L Ca (OCl)2, pH 5–6, 3 h of leaching. The effects of the: (i) Ca(OCl)2 concentration, (ii) NaCl concentration, (iii) pHrange and (iv) the effect of pulp density in the extraction of gold were assessed. In addition, the stability of the hypochlorite solutions (OCl−) was investigated. The ideal concentrations of Ca(OCl)2 and NaCl were determined as 25 g/L and 15 g/L, respectively, whereas the optimal pH range was 4–6. Under these conditions, the final gold extraction reached approximately 84%. By varying the solids content of the pulp (10%, 20% and 30%), it was observed that the lower solids value resulted in greater gold extraction (84%). The degradation of the hypochlorite solution and the possible catalytic effect of the presence of the solid were evidenced. To sumup, in the experiment, high gold extractions were achieved in shorter periods of time (3 h), as compared to the cyanidation of the same sample. On the other hand, itwas necessary to use significant amounts of the reagent due to hypochlorite instability at the pH conditions recommended for high gold extractions.

By S. N. Monteiro, C. M. F. Vieira, M. M. Ribeiro

"This work has as its objective to evaluate the effect of incorporation of the powder waste retained in the eletrostatic precipitator of the sintering stage from an integrated steel making plant on the physical and mechanical properties of a red ceramic. Formulations were prepared with incorporation of the waste in amounts up to 20 wt.% into a kaolinitic clay. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 750, 900 and 1050°C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The results showed that the waste has a potential to be used into red ceramics. The incorporation of the waste enhanced the properties of the ceramic, decreasing the water absorption and increasing the mechanical strength at all investigated temperatures.IntroductionThe sintering stage of an integrated steel-making plant is dedicated to the agglomeration of a mixture of iron ore, coke or coal, fluxes and water [1]. It is a common practice in this stage to use of solid wastes with great amounts of iron in the form of sludge and powder. One of the atmospheric pollutants generated during the sintering process is the particulate material, which is normally retained in an equipment denote as electrostatic precipitator. This equipment retains very small particulates, present in the gaseous emissions by application of an electrical potential difference in between the plates that the fluid is forced to go through. [2]."

Jan 1, 2011

By Kota Nakashima

Residues from titanium smelting tend to contain scandium. The scandiumis discarded because no suitable process exists for its recovery from the residue. Valuable-metal recovery from discharged residue is critical for environmental conservation and to achieve a sustainable society. Since 2015, JXNippon Mining&Metals has been developing a process for scandium recovery from the residue of a titaniumsmelting process. The process consists of the following steps: scandium concentrating by classification or neutralization, selective scandium leaching, impurity removal by neutralization, solvent extraction of scandium by using D2EHPA, purification, and roasting. We optimized the above steps to achieve an effective process to obtain scandium oxide (Sc2O3). In this paper, we introduce results from the bench-scale test of the scandium recovery flowsheet developed by JX Nippon Mining & Metals.

By Jorge Alberto Soares Tenório, Viviane Tavares de Moraes, Denise Crocce Romano Espinosa, Franco Alves Lavacchini Ramunno

"The traditional process for recovery of metals from waste electric and electronic equipment (WEEE) usually involves pyrometallurgical processing. However, the application of this technology to processing waste printed circuit boards (WPCBs) might lead to the formation of dioxins and furans, due to thermal degradation of flame-retardants and polymeric resins present in the board substrate. Therefore, this paper proposes a hydrometallurgical route for the recovery of copper. The acid leaching behavior of copper has been investigated at three different temperatures (25°C, 50°C and 75°C) with and without the addition of an oxidizing agent (hydrogen peroxide - H202). The dissolution kinetics for acid copper leaching was calculated based on chemical analysis by ICP-OES (Inductively Coupled Plasma - Optical Emission Spectroscopy). At 50°C with 1 mol/L H2S04 added 10 mL H202 (30%) each half hour under pulp density of 1 g I 10 mL, 100% of copper was extracted after 3 hours. The dissolution kinetics of copper with H2SO4-H2O 2 followed 1 - (1 - X)113 =Ket, i.e. chemically controlled reaction model.IntroductionThe information regarding the generation of waste electric and electronic equipment (WEEE) are still difficult to obtain because the estimates should take into consideration the historical production and sale of various products and the rate at which they reach the end of their life cycle, whose duration depends on the behavior of consumers [1]. Thus, the estimated overall WEEE generation varies between 25 and 50 million tons each year, which corresponds to more than 5% of all municipal waste generated [2], and this amount will increase at a rate of 3 to 5% per year, approximately three times faster than other individual types of waste [3].Printed circuit boards (PCBs) are essential parts of electric and electronic equipment (EEE), being found in virtually all electronic products, as well as in weapons systems [4]. A PCB is a basic component, which consists of a board where copper tracks are deposited. While the board behaves as an electrical insulator, the tracks connect electrically the various components attached to the board [ 5]. In addition to glass fibers, paper and resins, the PCBs contain significant amounts of metals, such as copper, iron, nickel, lead, stain, silver, gold and palladium [6]. In general, the weight fraction of metal is around 28% and the remainder of the boards is composed of plastic (19%), bromine (as flame retardant - 4%) and ceramic material (49%) [7]."

Jan 1, 2014

By Isabela Leao Amaral da Silva, Felipe Perisse Duarte Lopes, Alice Barreto Bevitori, Sergio Neves Monteiro, Ruben Sanchez Rodriguez

"The fibers extracted from the stem of the ramie plant are among the strongest natural lignocellulosic fibers with a potential to be used as reinforcement of polymer matrix composites. Characterization of the ramie fiber has recently been conducted for its physical and mechanical properties. However, the effect of increasing temperature on the ramie fiber behavior has not yet been fully investigated. Therefore, the objective of this work was to perform a thermal analysis on ramie fibers with different diameters within the naturally found range of practical interest. The analysis was conducted by thermo-gravimetric, TGA and DTG, as well as differential scanning calorimetric, DSC, techniques. It was found that the ramie fibers present thermal stability up to 200°C and then suffer a sharp deterioration between 300 and 500°C, resulting in characteristic peaks.IntroductionSince the middle of last century, polymer composites have substituted many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffness requirements that could be reached with synthetic fibers such as glass, carbon and aramid fibers. In recent years, however, the use of synthetic fibers is being questioned in terms of problems caused to the environment. In fact, as non degradable material, synthetic fibers are associated with long term pollution when discarded. Moreover, the expended energy for fabrication and processing can be related to relatively large amounts of C02 emissions and represents a contribution to global warming [3]. Glass fiber, in addition, is toxic and cannot be incinerated as a waste in thermal power plants [ 4]. Possible substitutes for glass fiber are the natural fibers. Many natural fibers are today being considered as viable alternatives to replace glass fiber as reinforcement of polymer composites. In particular, some natural lignocellulosic fiber extracted from plants present a real potential for this replacement [2-8]. Their comparative advantages are lower density and reduced cost as well as renewability, biodegradability, recyclability and neutrality with respect to C02 emission [3]."

Jan 1, 2011

By S. Abe

An extensive study has been carried out to determine the true cause of floating slimes precipitation which sometimes occurs and badly affects the quality of copper cathodes. Soluhilities of floating slime compounds systematically measured for the ternary system As-Sb-Ri added solely or in combination with conventional copper electrolyte (63°C) and bench scale electrorefining experiments done by varying electrolyte composition, have shown conclusively that the level of Sb(V) ions plays a substantial role in the precipitation mechanism. It was, therefore, speculated that controlling the level of the less soluble S b ( V ) ions below a certain critical level should result in a complete elimination of the undesirable precipitation. This can be easily achieved, for instance, by the addition of a reducing agent such as SO2 gas and the simultaneous employment of a certain type of cheating agent that effectively removes excessive Sb and Bi from the contaminated electrolyte. Long-term pilot testing conducted in line with the above speculation has confirmed the SO2/chelating resin scheme to be industrially very attractive and feasible.

Jan 1, 1987

By W. G. Davenport

The remainder of this book develops and uses mass and heat balances to describe steady"state flash smelting. Its objectives are to: a) describe the many ways a flash furnace operator can produce specified products, e,g. 65% eu matte, 35% SiOz slag, 1500 K (b) determine the oxygen, air, flux and hydrocarbon fuel requirements of each method (c) show how the flash furnace can be controlled to give specified products with varying feed compositions (d) suggest how the flash furnace operator can maximize profitability while producing specified products. This chapter develops the basiC heat and mass balance equations of steady-state ?flash smelting. It then adapts the equations to industrial feed materials .and products. Lastly it determines the amounts of oxygen and flux needed to produce molten matte and 35% SiOz slag from chalcopyrite concentrate in an Inco oxygen flash furnace,

Jan 1, 2001

By R. J. Wesely

The paper describes the various methods which are currently being used or considered to refine gold and silver. These methods are then compared on a technical and economic basis. Conclusions are drawn on the factors which might influence the choice of process for different feed stocks and economic constraints

Jan 1, 1990

By Mike Dry

Conventionally, lithium-bearing brines are processed via solar evaporation, chemical purification, and either electrolysis to lithium hydroxide or precipitation of lithium carbonate. Lithium-ion battery technology and electric vehicles are forecast to greatly increase the demand for lithium, but not all lithium-bearing brines are amenable to the conventional extraction process and new approaches are being developed. The chemistry associated with conventional lithium extraction is outlined and two new approaches are discussed.

By Baozhong Ma, Qian Li, Yonggang Wei, Shiwei Zhou, Bo Li, Chengyan Wang, Hua Wang

The magnesium-rich nickel oxide ore (w (Ni) =1.09 %, w (MgO)=29.08 %) mixed with 6 % and 8 % anthracite were roasted at different temperatures. XRD and SEM/EDS techniques were utilized to characterize the phase and microstructure transformation of the ores. The results show that lizardite and chrysotile of raw ore were converted into forsterite and enstatite during reduction roasting process. Simultaneously, iron and nickel oxide were reduced and migrated from the initial magnesium silicate. Fe3Si were formed when the roasting temperature went up to 1300 ℃ and 1350 ℃, and a small amount of Ni was observed in it. Temperatures got too high were not benefit to the polymerization of ferronickel.

Jan 1, 2015

By José Brant, Douglas Torres, Rogério Navarro, Rodrigo Souza, Eduardo Brocchi

The steelmaking process requires the input of ferro-alloys to implement the adjustment of some elements composition in the final product. In the particular case of stainless steel production, the high carbon FeCr alloy stands out as one important precursor. However in the production of this material a certain quantity of fine powder with remarkable chromium and carbon content is also generated, which, in turn, could be processed through alkaline roasting in order to selectively recovery this element in a subsequent aqueous route. In the present work, this process is investigated, using excess of NaOH as oxidizing agent, and H2O2 for precipitating chromium as Cr(OH)3, which is next calcinated to Cr2O3. According to the results, the global achieved recovery has shown to be around 98%, suggesting that the proposed route can be seen as a potential process for chromium oxide production from the mentioned fine powder.

Jan 1, 2015

By Larry G. Twidwell, Jannette L. Chorney, Bryce D. Ruffier, Katelyn M. Lyons, Daniel W. Gaede, Ryan J. Foy, Jerome P. Downey

The Metallurgical and Materials Engineering Department at Montana Tech is investigating various methods of extracting and refining rare earth elements from mineral ores and concentrates. As part of this research, an elevated temperature “roasting” process has been evaluated as a means of converting the rare earth elements contained in various matrices to bromides as a pretreatment step in preparation for downstream rare earth element extraction and recovery operations. Laboratory and bench-scale experiments have been performed to assess the effects of varying temperature (150 to 400° C), time (1 to 4 h), and the ammonium bromide to rare earth oxide molar ratio (6 to 24) in the roaster charge. The results show that nearly complete bromination of the rare earth oxide is achievable when the roast is performed under optimum conditions.

Jan 1, 2015

By Xu-ling Chen, Qian Li, Yong-bin Yang, Zhao Jing, Tao Jiang, Guang-hui Li

"It is generally known that alkali metals are harmful to blast furnace production resulting in aggravating RDI of sinters, abnormal expansion of pellets, deteriorating blast furnace lining, etc. Sinters regarded as dominating burden of blast furnace are determined as the main source of alkali metals. In this study, the removal behavior of potassium and sodium oxides by pre-reduction sintering during the sintering process was studied. The removal ratio ofK20 and Na20 was greatly influenced by coke powder content, carbon species, coke powder adding ways, additive and so on. Under the conditions of carbon rate 12% and 5% dosage of CO supplied in the sintering process, the corresponding removal ratio ofK20, Na20 was 69.00% and 32.79%, and metallization ratio could reach 4.65%. This technology provided a novel process for reducing the content of alkali metals in sinters and dramatically improving the quality of blast furnace burden.IntroductionSinter is the main iron-bearing charge of blast furnace for iron-making in China, making up about 80% of the total burden; therefore, its quality has a significant influence on the quality of pig iron and blast furnace operation. Research and practice of numerous years prove that potassium and sodium coming from ores are brought into blast furnace and upgraded, which is one of the essential reasons that lead to blast furnace nodulation and influences its strength. Currently, effective flow sheet to remove potassium and sodium is weak magnetic separation-intensive magnetic separation-flotation [l], while iron ore concentrate is still ofhigh levels of potassium and sodium. As sintering process is also not effective to remove potassium and sodium, blast furnace in China is of high alkali burden, e.g. it reaches 5.6-6.2kg/tFe in Baotou iron making plant, which is greater than international tolerated level of2.55kgltFe [l]."

Jan 1, 2013

By Shi Guan-Yong, Niu Li-Ping, Dou Zhi-He

"In the preset work, the viscosity model (named modified KTH model) proposed by Sichen Du and S. Seetharaman et al and extended by Shu Qi-feng was applied to the ESR slag systems. A correlation to predict the viscosities of CaF 2-(CaO)-Al203 slags using interaction coefficients of different cations in the presence of oz-and viscosity interaction coefficients between oz-and F in the presence of different cations has been developed. The interaction coefficient between oz- and F- in the presence of Al3+ was determined from the experimental data as shown in known literatures. The good agreement between the calculated viscosities and the experimental data in the CaF2-(CaO)-Al203 systems has indicated that this approach can be successfully employed to predict the viscosities of ESR slags.IntroductionReliable viscosities data of high-temperature slag melts are important for the modeling and design of high temperature metallurgical processes. Although a number of experimental measurements have been carried out, the available viscosities data is still scarce compared to the needs of today's technology, especially in the case of complex melts. In process simulations, the needs of viscosity descriptions for complex systems which could enable the extrapolation of the data as functions of temperature and composition is strongly felt today."

Jan 1, 2013

By Tianzu Yang, Weifeng Liu, Lin Chen, Wei Chen, DUCHAO ZHANG

Ni-M (Metal=Cu, Fe, Co, Mn, Zn, Cr) aerogel catalysts were tested for CH4 oxy-CO2 reforming. It was found that the Ni-Co bimetallic aerogel catalyst had the highest activity and stability in methane oxy-CO2 reforming among all the Ni-M aerogel catalysts. It exhibited a steady activity of 79 % (in terms of CH4 conversion) at 750 oC, which is the highest activity under a similar reaction condition as compared with those published in literature. Characterizations for the reduced catalysts indicated the formation of Ni-Co alloy, while other transition metals separated from Ni during the reduction process. Therefore, the active species in the Ni-Co bimetallic catalyst showed a stronger interaction than those in other Ni-M catalysts, which might be one of the main reasons for the better catalytic performance of the catalyst.

Jan 1, 2016

By Christiana Mystrioti

Greece is the only EU country with extensive nickel laterite deposits. Since the 1960s, the Greek laterites are treated for ferronickel production via a pyrometallurgical route, which involves pre-reduction of the ore in rotary kilns and reduction smelting in electric arc furnaces. Due to the rising cost of energy and the decreasing grade of mined laterites, the pyrometallurgical treatment is economically marginal. For this reason, alternative treatment processes are currently under investigation. Potential applicability of hydrometallurgical treatment, using either H2SO4 or HCl, under atmospheric pressure conditions, for Ni and Co extraction from two low grade laterite ores, was examined in the present work. The two samples were selected to represent the different mineralogical composition of the saprolitic and limonitic ore deposits of the Greek laterites. The investigated parameters were temperature (65–90 °C), acid concentration (1–4 N) and solid to liquid ratio (10–30% w/v). The results indicated that HCl was more efficient than H2SO4 for the treatment of the saprolitic ore; Ni and Co extractions were very high for both elements, up to 98% and 96% respectively, while H2SO4 could leach efficiently Ni, up to 100%, but extracted only 34% of Co. Hydrochloric acid was also more efficient for the treatment of the limonitic ore, with Ni and Co extractions up to 98.3% and 87.6% respectively. With H2SO4 the maximum extractions were 71.3% for Ni and 52.1% for Co.

By Saad Elias Kaskah

"The Box-Behnken Design (BBD) is used to model the sacrificial Cathodic Protection System (SCPS) to find the factors effectiveness behaviour. For protection potential assessment the BBD receives (resistivity of environment, sacrificial anode alloy, distance between anode and cathode and surface area for the structure to be protected) as input and gives the protection potential as output. By applying BBD with their analysis tools we get many results. The important results which are the factors individual effectiveness on the sacrificial cathodic protection (SCP) process are the resistivity which has the greatest effect on the potential protection (rank=l) followed by sacrificial anode alloy type (rank=2), surface area for structure protected required (rank=3) and distance between anode and cathode (rank=4). The interaction of sacrificial anode alloy and cathode area {X2X4 ) has significant effect on CP process with the limits which are used in this work while the other factors interaction (X1X2, X1X3, X1X4,X2X3, X3X4 ) has insignificant effect on the limits which used in this work.IntroductionFor carbon steel in seawater the normal corrosion potential E '°""_is in the range -550 to -600 mV vs. Ag/AgCI [1]. The most effective method to overcome the corrosion is cathodic protection {CP) which represents a control method in the steel wall corrosion. Cathodic protection has been used in several areas including marine and underground structures, storage tanks, and pipelines [2]. Sacrificial anodes system generates protective current which depends upon the inherent potential difference between the anodes and the structure to be protected. If the structure is made of iron or steel, any metal that is more active in the electromotive force series can theoretically be used as anode material [3]. There are many factors influencing on cathodic protection like resistivity (NaCl content), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode, temperature, humidity, velocity of solution, dust, impurities, bacteria and etc .. The present work studied four factors: NaCl content, resistivity), chemical composition of sacrificial anode alloy, distance between anode and cathode, surface area of cathode) with different three levels of values for each one. Then this work will find the optimum value from the factors levels that tacked to investigated there influencing on sacrificial cathodic protection system."

Jan 1, 2013

By Denise Cristina de O. Nascimento

Natural lignocellulosic fibers are increasingly being used as polymeric matrix composite reinforcement owing to economical and environmental advantages as renewable and biodegradable materials. Among these, the piassava fiber extracted from a palm tree native of South America stands as one of the most rigid with a potential to be used as composite reinforcement. Therefore, the present work investigates the notch toughness behavior, by Izod impact tests, of epoxy composites reinforced with up to 40 % in volume of continuous and aligned piassava fibers. It was found that the incorporation of piassava fibers results in significant increase in the impact energy of the composite. Scanning electron microscopy analysis showed that the nature of the piassava fiber interface with the epoxy matrix is the major responsible for the superior toughness of the composite.

Jan 1, 2009