Search Documents

By Jie Li, Longxiang Li, Wenbing Guo, Gaobo Zhao, Yuhang Hu

Surface subsidence caused by underground longwall mining is a very complicated process in time and space, influencing building and structures on the surface of the mining area, including houses, pipelines, and highway. The field monitoring data of surface subsidence are essential for protecting them. This study investigated the dynamic and residual subsidence characteristics of both the surface and the highway over a 730-day monitoring period on a longwall panel. Three monitoring lines (Lines 1–3) were established to monitor the subsidence process, and three stages were identified: initial stage of surface subsidence, active period of surface subsidence, and residual subsidence deformation stage. The maximum subsidence value on the highway (1,786 mm) was smaller than that on the surface (2,094 mm), and the maximum subsidence velocity on the highway (41.7–50.8 mm/day) was also lower than that on the surface (66.7 mm/day). During the residual subsidence deformation stage, both the surface and highway subsidence velocities decreased to below 0.6 mm/day. Furthermore, differences in subsidence characteristics between the surface and the highway were analyzed, with the subsidence value on the highway always being less than that on the surface, while the subsidence velocity during the residual deformation stage was not always lower. This could be attributed to the influence of dynamic loads from vehicles, which could induce additional residual subsidence on the highway. Further investigation into this phenomenon will be conducted in future research.

Jul 1, 2023

By John H. Bassarear

Large scale equipment can reduce both capital and operating costs for concentrators. Large semiautogenous mills can be effectively utilized in big mills but they must be kept fully loaded to take advantage of their great potential. With varying hardness ores, controlling throughput is difficult and careful design must take this into consideration. A variable speed drive on large primary semi- autogenous mills can overcome this problem to a considerable degree. This paper provides a base case using standard accepted technology of two wound rotor single speed 4,476 kW (6,000 hp) motors to drive the primary SAG mills of a hypothetical 36,364 mtpd (40,000 stpd) typical porphyry copper mill. One other fixed speed drive will be described and five variable speed drive configurations will be reviewed. Capital costs for the entire grinding circuit, from crusher product to flotation feed, were developed for the base case and each of the alternatives. A technical evaluation comparing the advantages and disadvantages of each drive is presented.

Jan 1, 1985

By Michael A. Redfearn

The use of nitrogen in molybdenite flotation circuits is a relatively new concept utilized by only a few mines around the world. This paper briefly discusses circuit chemistry and the reason for its success. It follows the entire testing process which resulted in a sodium hydro-sulphide dosage reduction from 18.5 to 4.4 lbs/ ton (9250 to 2200 g/t) through to the final installation of an inert gas generator which will produce reagent savings in excess of one million dollars annually. A description of the various types of nitrogen generators commercially available is included.

Jan 1, 1983

By S. Veeramasuneni

The interaction of soluble salt particles in their saturated brines is of interest from both a fundamental and practical perspective. The state of dispersion/aggregation of alkali halide particles as determined by optical microscopy can now be described based on non-equilibrium electrokinetic measurements for alkali halides. These results indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. These experimental results can be explained based on the interfacial polar interaction theory. In this regard the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems.

Jan 1, 1997

By H. W. Newcomen, D. R. Brox

Assessments of the stability performance of open pit highwalls have traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work have been reviewed and are generally endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on the observed trends in highwall strain data from the case histories presented.

Jan 1, 2004

In 1981, North American Degerstrom Contracting began gold mining on the Little Rocky Mountain Range, near Zortman, MT. In the past four years, the price of gold has fluctuated from a high of $16/g ($500 per oz) to a low of $9.60/g ($300 per oz). With that kind of a moving target, profitability presents a management challenge. Based in Spokane, WA, Degerstrom employs 85 people at the mine. It is one of the largest heap leach operations in the nation. Last year, 8 Mt (9 million st) of low-grade ore was moved to the leach pads in a two-shift, five-day operation. The current pit being worked produces 218 kt/m (240,000 stpm) of leaching ore. Ore fragmentation critical The gold bearing ore has no defined patterns or seams. It is an igneous intrusion resulting from volcanic activity. It occurs spontaneously throughout the range. To recover the gold, areas are staked out and core samples are taken and analyzed. These data determine if the ore is rich enough to mine. Once mining begins, an average of 150 holes are drilled and blasted on a two-day rotation. Five Ingersoll-Rand T4s drill on a 4- x 4.5-m (14- x 15-ft) spacing to a 7.6-m (25-ft) depth. "When we first came to this site, we drilled on a 3.6- x 3.6-m (12- x 12-ft) pattern," said Paul Baker, superintendent for N.A. Degerstrom Contracting. "We did some experimenting using a high density emulsion in the bottom of the hole and filling the rest with regular Anfo." The high density emulsion saved the company on overall drilling and blasting costs since the holes could be spaced on a wider pattern and still achieve the high degree of fragmentation needed for leaching. Blasting is important because the gold lays in the natural strata of the rock. Also, the ore is not crushed before it goes to the leach pads. So complete fragmentation is critical. Terrain dictates loading/hauling system The shot ore is worked in 6 m (20 ft) benches by two Caterpillar 245 front shovels equipped with 3 m3 (4 cu yd) buckets, a 992C wheel loader with a 12.6-m3 (16.5-cu yd) bucket, and a 988E high lift fed by a D9H. A Caterpillar D10 tractor trap dozes to the loader. According to Baker, the 6 m (20 ft) bench is an efficient lift for the front shovel and the wheel loader. In tight quarters or in a pocket of ore, Degerstrom uses the 245s. For high production areas, the wheel loader is used. The hauling fleet includes 28 Cat 773 off highway trucks. The 45 t (50 st) trucks are seven pass loaded by the 245s with a 25-second cycle time per bucket load. The 992C loads the trucks in two passes in less than 30 seconds. The cycle time is four to five minutes for a 1.2-km (4000-ft) haul on grades that average 10%. Grades, in some places, exceed 16%. "We use the 773s because they have a low weight-to-horsepower ratio - that's what you need in steep country," Baker said. The trucks haul the shot ore to the leach pad. Currently, Degerstrom is working a pad that has a capacity for 5 Mt (5.5 million st) of ore. Building the leach pads The base of the pads resemble a large drainage basin. They take about one month to construct. A 0.3-m (1-ft) layer of impervious bentonite clay is hauled in and leveled by a Cat D9H tractor. A 30-mm (1.2-in.) PVC liner is then laid in place on top of the clay base. It, in turn, is covered with tailings from an old on-site mill. Degerstrom uses the tailings to protect the liner from tears when the ore is dumped. The ore is leveled and built up in 9 m (30 ft) lifts by the D9H. The tractor rips the top layer. Then, a network of plastic irrigation pipe is put in place to distribute a cyanide solution over the surface. The leaching solution percolates through the ore and dissolves the gold. The solution drains from the pads and is pumped to a 22.7-ML (6-million gal) pregnant solution holding pond. The liquid then goes through two separate filtration units. One unit removes entrained solids and the other side adds a zinc dust to precipitate the gold. This is collected on filters. The affluent then returns to a solution holding pond for redistribution through the pipeline network. Typically, 80% of the pad's potential recovery takes place in the first 30 days of leaching. The process stops when the ambient temperature falls below the cyanide's freezing level. And each pad has a leach cycle of four to five years before recovery values decline to a point where further leaching becomes uneconomical. At Zortman, it takes 9 t (10 st) of ore to produce 31 g (1 oz) of gold. It is therefore critical to keep total production costs down and efficiency high.

Jan 1, 1986

By F. J. Susko

The Bureau of Mines applied a flotation model to the hydrodynamics of the Bureau-developed rapid flotation system. Rapid flotation is a process which separates the bubble-particle attachment and froth-pulp separation stages of the flotation sequence into two discrete unit operations allowing the operations to be individually optimized. Both an air-injected hydrocyclone and an in-line mixer were used as the bubble-particle attachment unit and a shallow-depth froth separator was used to separate the ore-laden froth from the pulp. A 10-L/min batch system was tested on a coarse coal feed sample. The system was tested using two different bubble-particle attachment units at various aeration levels in order to test the flotation model. The results of the flotation model reflect general trends observed in the experimental data.

Jan 1, 1993

By M. T. Ityokumbul

The liquid phase mixing in Western Research Centre (WRC) pilot plant flotation column with diameter of 0.76 m has been characterized using a salt tracer. The process variables studied were gas and liquid flow rates. The response of the column to a tracer pulse input was monitored at three axial and two radial locations. For all the experimental conditions investigated in the present study, radial and axial concentration gradients were not observed. It is thus concluded that the 2 tph flotation column is behaving as a well mixed tank. This finding is consistent with the observed poor recoveries of coarse fractions in the column flotation circuit. Based on the findings of this report, it is recommended that several schemes of reducing the backmixing be implemented and evaluated for their effectiveness in improving the column recoveries.

Jan 1, 1994

By D. J. Boron, R. Kollrack

Introduction The US has the largest total (364 Gt, or 401 billion st) and recoverable (182 Gt, or 201 billion st) coal reserves in the world (Steam/Its Generation and Use, 1978). However, progressive coal use in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. Since the promulgation of the Environmental Protection Agency (EPA) New Source Performance Standards (NSPS), it has become apparent that all US coals will require sulfur removal to comply with the new sulfur dioxide emission levels. If more stringent emission standards are imposed, through pending acid rain legislation or amendments to the Clean Air Act, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the development of new and advanced coal cleaning technologies to continue and promote the use of coal. Table 1 summarizes the EPA NSPS for sulfur dioxide emissions. Fortunately, the basis for determining sulfur dioxide removal is the Btu and total sulfur content of the run-of-mine coal. Thus, credit is given for any sulfur removed before combustion, e.g., through physical coal cleaning. Unfortunately, physical coal cleaning alone may be unable to produce a compliance coal with respect to the EPA NSPS. Therefore, all industrial and utility coal-fired boilers will require post combustion gas cleanup, e.g., flue gas desulfurization (FGD), to comply with the new regulations. Table 1 - EPA NSPS for SO2 Emission Category SO2 Content of ROM Coal SO2 Reduction Required 1 0-2 Ib/M Btu 70 2 2-6 Ib/M Btu To 0.6 Ib/M Btu (70% to 90%) 3 6-12 Ib/M Btu 90% 4 12 Ib/M Btu To 1.2 Ib/M Btu Alternatives to post combustion gas cleanup, such as staged combustion, lime and coal injection, fluidized-bed combustion, and chemical coal cleaning, are currently under development. Of these, chemical coal cleaning offers the advantages of providing (1) high quality fuel for combustion (low sulfur and ash, high Btu, and attenuated product variability); (2) a solid fuel product for use in retrofitted gas and oil boilers; and (3) a solid fuel product with multiple end uses, e.g., internal combustion engines, carbon electrodes, coke, or chemical feedstock. Gravimelt process In the Gravimelt process, 1.4 mm x 0 (14 mesh x 0), physically beneficiated coal of about 5% moisture is fed into a 3401 to 3901 C (644 ° to 734 ° F) molten bath of sodium hydroxide and potassium hydroxide. Organic and pyritic sulfur and most of the mineral matter in coal react with and are dissolved in a molten mixture of potassium hydroxide and sodium hydroxide. The reacted coal sulfur is converted to alkali sulfides and polysulfides, whereas the mineral matter is apparently converted to alkali-aluminum silicates and other byproducts that are water and acid soluble. Coal residence time is 60 to 240 minutes. The sodium hydroxide to potassium hydroxide ratio is about 9:1. The total hydroxide-to-coal ratio is no less than 10:1. The specific gravity of the caustic melt is about 1.8 g/cm3 . Thus, coal is buoyant in the bath, and insoluble mineral matter with density greater than 1.8 g/cm3 would sink. Reacted coal is first water-washed with an equal weight volume of water in a countercurrent mode of operation. The coal is filtered and the filtrate sent for regeneration. The coal is then acid-washed in 10% sulfuric acid. The acid-water/coal mixture is filtered to recover the final coal product, and the filtrate treated with lime to precipitate dissolved mineral matter. The precipitate is filtered from the mixture and discarded. The water is recycled to the plant. Filtrate from water-washing is treated to remove sodium sulfide. The sodium sulfide is chemically treated to produce hydrogen sulfide, calcium car¬bonate, sodium hydroxide, and other products. The hydrogen sulfide is treated to produce sulfuric acid for the acid-washing step. The calcium carbonate is treated further or discarded, and the sodium hydroxide is concentrated by evaporation and recycled to the reactor. The Gravimelt process is currently at the bench-scale stage of development. A 0.9-kg (2-lb) continuous reactor is in operation with a continuous water- and acid-washing section adjacent. The regeneration section is not developed to a meaningful extent, although key reactions have been tested in the laboratory. Process conditions, product recovery efficiencies, etc., however, have not been determined adequately and continuous regeneration operation has not been attempted. Work is now in progress to develop each section to a continuous bench-scale operation in processing coal at 9.1 kg/h (20 lb per hr). Microwave process The carbon and hydrogen in coal are relatively transparent to microwave radiation. However, water, caustic, pyrite, and other mineral matter components are strong conductors of microwave radiation energy at the proper frequency. As a result, selective heating of the noncarbonaceous materials occurs that enables the chemical reaction of sulfur and ash with caustic. Although very high temperatures may result from

Jan 1, 1987

By S. C. O?Brien

This paper develops the procedure for simulating the special locked-cycle Work Index laboratory test using the kinetic parameters obtained by conducting standard size-mass balance (SMB) grinding tests and presents the results for three materials - quartz, a taconite iron ore and a bituminous coal. It was found that the WI could be determined by simulation; however, if a material breaks abnormally, a full description of its abnormal breakage is necessary. It was also found that the sensitivity of the WI test procedure to the sieving process and the estimating of the 80% passing size of the sieve undersize is sufficient to question the practice of quoting a WI to two or more decimal places. Finally, if a material grinds abnormally in the Work Index mill, then the WI test should not be conducted.

Jan 1, 1987

By D. J. McParland

This paper will deal with some of the considerations which, were involved in the design and construction of the uranium mills in the Elliot Lake area . These plants, eleven in number, range from 1500 to 6500 tons per day milling capacity. Most references are with respect to the seven plants in the Rio Tinto Group which have a combined milling capacity in excess of 20,000 tons per day. In dealing with such abroad subject as mill design, one has the choice, of covering a few specific problems in great detail, or else attempting to cover many subjects superficially and briefly. In preparing this presentation, an attempt has been made to compromise on these extremes, and to select some interesting illustrations which are of general interest in the field of mill design, and of value to persons concerned with mill design broadly, beyond the field of uranium mills.

Jan 1, 1959

By M. R. Peterson

The U.S. Bureau of Mines (USBM) is investigating alternative methods to strip metal-loaded solvent extractants. Hydrolytic, precipitation, and hydrogen pressure stripping all recover metal or metal salts directly from the organic solvent extractant. Pure metals, metallic oxides, or metal salts can be formed, allowing direct production of value-added products. Aspects affecting commercial application are emphasized, including metal recovery from actual ore leach solutions, particle size control, organic modifier and diluent effects on stripping and metal recovery efficiencies, metal grade, seed addition, mixing intensity, recycling efficiency, and reactor plating. Metal separations from copper ore leach solutions and complex waste leach solutions were examined.

Jan 1, 1995

By D. Einarson, B. Strickland

The decision to accelerate development of Stillwater Mining’s East Boulder Mine was made in March of 1998. It required the completion of conceptual designs by July of 1998. This was accomplished through teamwork and close cooperation of mine personnel, engineering firms and vendors, all working toward the common goal of developing an efficient and workable design. Early in the project, representatives of Stillwater Mining, Kilborn International, Parsons Brinckerhoff Transit and RailSystems, Continental Conveyor, and H.A. Simons met to develop methods to bring the mine into production at a highly accelerated rate and to solve potential bottlenecks, including the movement of personnel, materials, and muck through a 5.6 km(3-1/2 mile) adit. This interaction, including companies not normally associated with the mining industry, led to innovative approaches and designs produced by Kilborn Engineering and Stillwater Mining.

Jan 1, 1999

By K. E. Harrison

The acid rain legislation has passed into law. This new law has caused the power generation community to investigate alternative methods to obtain compliance with the new legislation. One thing all of the power companies have concluded is the answer is not easy. Do we switch fuels to burn all low sulfur compliance coal? Maybe possibly only partial desulfurization by means of a dry sorbent system? Or, finally, maybe a wet scrubber system? Whatever the choice, the power community needs to investigate all of the alternatives. In 1988, ICF Kaiser Engineers, Inc. (ICF KE) responded to a request by the U.S. Department of Energy for the engineering development of advanced physical fine coal cleaning. ICF KE responded and was awarded a contract to conduct a multi-task program to develop an advanced flotation system to eliminate pyritic sulfur and retain as much energy as possible. ICF KE assembled a team that included members of industry, academia, and industry research organizations to conduct this multi-task program. The program includes sixteen (16) tasks. This team had personnel to help solve some of the anticipated problems and to provide industry prospective on the viability and commercial potential for any concepts proposed. The primary team consists of a major coal producer, Babcock and Wilcox, Eimco Process Equipment Company, and Virginia Polytechnic Institute and State University.

Jan 1, 1992

By Neely H. Bostick

The primary and secondary organic matter in sedimentary rocks changes markedly when it becomes heated as a consequence of thick sediment accumulation and normal geothermal gradients, high geothermal gradients, hydrothermal fluids, or igneous events. Contact zones adjacent to small igneous dikes allow sampling of a single sedimentary bed that has been exposed to temperatures in a range as great as 30-500°C. Dike-heated rocks are, therefore, good sites for research on thermal effects because variation of the original organic matter is minimal, the range of heating is great, and the history of rock heating in a dike zone is relatively well established. In rare cases, such as at the dike near Wolcott, Colorado, described in this paper, the rock samples are sufficiently unweathered to allow analysis of secondary bitumens generated by the heating. We show by optical microscopy, scanning and transmission electron microscopy, and geochemistry the kinds of solid organic constituents in sedimen¬tary rocks and in ore deposits and the effects of heating. The primary phytoclasts that make up kerogen In sedimentary rock and in some ore deposits (pollen, resin, charcoal, humified woody remains, etc.) change in ways that are familiar to coal specialists. Progressive loss of moisture and other volatile matter yields residual kerogen that Is relatively higher in carbon and lower In oxygen and hydrogen, and has greater molecular or polymer ordering. In our contact zone examples, atomic H/C ratios of kerogen decrease from 0.8 (one case from 1.4) to 0.4, the hydrogen index from Rock-Eval pyrolysis decreases from 70 to 5, and the transformation ratio from Rock-Eval pyrolysis increases from 0.06 to 0.5 with increased heating. The visible effects of heating seen by scanning electron microscopy and light microscopy include formation of vesicles and flow structure, the development of optical anisotropy and mesophase, change of color, and increase in the refractive index, absorption, and reflectance. Some of these changes In primary organic matter are observed also in secondary organic matter, for example, in solid bitumens in sedimentary gold ores or In lead-zinc deposits. Quantification of color or absorption changes is difficult because it Is hard to make thin sections of organic matter with uniform thickness. However, natural objects with uniform thickness can be used. We show the colors of pollen In rocks from the Salton geothermal field at temperatures ranging from 100 to 300°C, and of pollen heated in laboratory bombs from 150 to 400°C. Measurement of vitrinite reflectance is a practical way to quantify thermal changes of kerogen and minerals of most sedimentary rocks because vitrinite is fairly widespread In sedimentary rocks of Devonian age and younger. For example, the reflectance of vitrinite rises from the regional level, as low as 0.4 % Ro, to more than 5% Ro adjacent to dikes that cut sedimentary rock. This is equivalent to the rank change from subbituminous coal to extreme meta-anthracite. The rise is most abrupt near thin dikes, but when the distance from the igneous contact is expressed as a ratio of dike thickness the reflectance rise is similar for all dikes. Controlled heating of vitrinite-bearing rocks In the laboratory provides a means to assign known temperatures to vitrinite-reflectance values. The derived plots of temperature In dike contact zones have the same shape and level as those predicted by heat theory, and the temperature lines extend toward dike contact temperatures that are about half those of most magmas, as expected if the intrusions did not flow past the sedimentary rock for a long time. The globular submicroscopic structure of vitrinite and Its heterogeneity, which we show by means of transmission electron microscopy, pose some problems In selecting a uniform type of vitrinite for measurement of thermal changes. At present, routine reflectance values of vitrinite dispersed in rocks have a relative uncertainty as great as 10%. Thermally caused chemical changes in the primary kerogen, especially decrease in the oxygen and hydrogen contents, lead to formation of secondary products in the contact zone. The measured changes of secondary organic products in these rocks include formation of peaks In concentration of total extractable organic matter and in hydrocarbons, and in the saturated/aromatic hydrocarbon ratio over the interval where primary organic hydrogen decreases most rapidly--then destruction or expulsion of these products at high temperatures. The odd carbon-number predominance of the C25-C31 n-alkanes In samples far from the dike disappears by about 1.3% Ro whereas the 13C: 12C ratios of the saturated and aromatic hydrocarbons increase over most of the thermal range. The saturated aromatic hydrocarbon ratio at first increases, corresponding to thermal generation of saturated hydrocarbons, then decreases in the most altered samples. One use of organic petrography, in addition to identifying organic fades or thermal alteration, is recognition of sample contamination such as the solid organic additives used in some drilling muds which may contaminate geochemical samples.

Jan 1, 2013

By Daniel R. Stewart

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines; support definition and slope stability at the Climax mine; and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1983

By D. Bhattacharyya

The adsorption and desorption of gold cyanide by activated carbon is significantly influenced by particle size of the activated carbon particles and the chemical environment. A series of adsorption and elution experiments have been performed with ten different particle size fractions. The tests indicate that although the ultimate adsorption capacity is independent of the activated carbon particle size, the adsorption rate is strongly affected by the particle size. Further, desorption characteristics using traditional Mintek and atmospheric Zadra procedures reveal interesting trends with variation in particle size and will be discussed in this paper.

Feb 23, 2014

By H. Fayed

Froth flotation technology is the backbone of the minerals pro-cessing industry where minerals are concentrated by selective separa-tion; either direct or in-direct flotation. In direct flotation useful minerals are conditioned to become hydrophobic (water-repellant) and attach to air bubbles while impurities (non-useful particles) remain in water. The hydrophobic particles are transported by air-bubbles to the top froth (foam) layer in flotation tank which can be removed as a concentrate. There are many factors that controls this selective separation process such as: particle’s degree of hydrophobicity, size, mass loading, air holdup and bubble size distribution. Turbulent fluctuation of the slurry in the tank is another important factor that controls the collisions rate between particles and bubbles and hence attachment rates. The turbu-lent fluctuations are measured by the local distribution of turbulent dissipation rates. Conventional flotation machines are restrained by residence time of the slurry that is about 3-5 minutes that results in a large footprint and limits the capacity of flotation plants. The designers of conventional flotation machines try to reduce the footprint of flota-tion tank by scaling up the flotation machines to increase plant throughput. The scale-up process reduces the specif power consump-tion and the local distribution of shear rates and turbulence dissipation rates. This scale-up results in a larger mean bubble size and lower particle-bubble attachment rates.

Feb 1, 2023

By Jian Deng, Hehua Zhu, Lianyang Zhang

Rockburst is defined as a sudden and violent explosion of rock on the surface of a rock excavation. Rockburst has been regarded as the least understood and most feared hazard problem for underground rock excavations. Traditionally, rockbursts were classified into the strain, pillar, and fault-slip categories. However, rockbursts are also known to occur at stress levels well below the rock yield strength, in mines where the rock is far from brittle, or without the presence of geological discontinuities. A plausible explanation of rockbursts is buckling, which has been identified as one of the main mechanisms for rockbursts. It is observed that rockbursts are often induced by dynamic loadings (pulses) from adjacent blasting. Therefore, the present paper studies the effect of pulse shape and amplitude on pillar rockbursts induced by dynamic loadings from blasting using the method of numerical analysis. The governing equation of a pillar’s motion is set up and the mechanism of pillar rockbursts is investigated through a practical example. The results show that it is not the shape of a pulse but the impact energy to decide the occurrence of pillar rockbursts. If all other parameters remain the same, pillar rockbursts are more likely to occur when the pulse duration is longer. The parametric resonance and the perturbation of dynamic loadings are also found to play an important role in the occurrence of rockbursts. These insights would provide invaluable clues about the mechanism and for better control of pillar rockbursts.

Apr 26, 2022

By Evan J. Owen, Virginia T. McLemore

of high specific gravity, resistant minerals that form from mechanical concentration by waves, currents, and winds in marginal-marine environments. These sediments are enriched in critical minerals such as titanium, zirconium, and REE. Cretaceous beach-placer sandstones are found in the Colorado Plateau of northwestern New Mexico. Originally discovered by airborne radiometric surveys for uranium in the 1950s, these beach-placer sandstones are being re-examined with modern methods as potential sources for critical minerals. Selected beach-placer sandstones have been sampled, mapped with ground radiometric surveys, and analyzed with whole-rock and trace element geochemical methods. Mineralogy is being determined with optical methods, XRD, and EMPA. Zircon, rutile, ilmenite, and monazite are the primary heavy minerals of interest found in the studied deposits. Initial results show that the sandstones contain up to 1.4% total REE, 29.4% TiO2, and an estimated 4.9% ZrO2. Chondrite-normalized REE diagrams show distinct light REE and minor heavy REE enrichment, as well as pronounced negative Eu anomalies for each deposit.

Feb 1, 2024