Search Documents

By Daryl R. Tweeton

Bureau of Mines research in in situ uranium leaching includes injection well construction and environmental aspects. Clogging of injection wells is a common problem, and is affected by construction techniques. Part of the clogging can be caused by a low-permeability skin left on the borehole wall if the drilling fluids are not thoroughly flushed out. Certain polymer drilling fluids are less prone to cause clogging than bentonite muds, since a lower solids content can be used. The environmental research primarily involves two contracts. The first describes the environmental impact of in situ leaching and the effect of environmental legislation on leaching; the second describes the cost effectiveness of various methods of restoring ground water quality.

Jan 1, 1978

By P. Roghanchi

The difficulties associated with performing direct tensile strength test lead to development of indirect test methods, which are simple, less expensive, and less time consuming. Splitting tensile strength test (Brazilian test) is performed by applying two opposite concentrated compression load across the diameter of a disk specimen until the failure occurs along the loaded diameter. Theoretically, the load is applied over a small width as a line load, however, by increasing the load, the contact width between the loading jaw and the specimen increases as the specimen deforms. The main aim of this study is to investigate the stress distribution in (1) regular Brazilian specimen in traditional tests with loading jaws and (2) flattened Brazilian specimen with flat platens. A series of the splitting tensile strength tests and uniaxial compression strength tests are performed on three rock types: rhyolite, basalt, and limestone. Further, Numerical modeling studies are performed to investigate the effect of the contact between jaw and Brazilian specimen on stress distribution in the disc specimen based on the results from the experimentation. Finally, the stress distribution in the traditional Brazilian test specimen and the flattened end Brazilian test specimen were compared.

Feb 23, 2014

By D. Hulse

"The science of “optimal economic pit design” has been highly refined in the last decades. Even with the proliferation of optimizing and heuristic algorithms exploiting ever faster computers, the most common input is a single block model and a single set of cost assumptions, each of which is an estimate and prone to errors. An analysis of price assumptions produces a suite of nested economic shells, each with its own quantities of ore, waste, grade, and profit, but due to irregularities in the mineralized body, the growth of these shells can be erratic. To control the impact of the errors of the model and cost assumptions when choosing the pit shell for design, graphs of pit shells characteristics, such as stripping ratio, cost per unit of product and profit/ton, can be analyzed to consider points with higher stability, or robust pits. Selection of robust shells for a pit limit and for push backs can help to understand the impact to profit and risk. The robust shells also guide the preferred solution sets for final pit and cutoff optimization. INTRODUCTION “An open pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface.” Optimum Design of Open-Pit Mines, Lerchs, H. and Grossmann, I. Transactions C.I.M. Volume LXVIII 1965. Traditionally an analysis of economic pit shells and sensitivity was performed by varying the input metal price. This was done with both floating cone algorithms as well as early versions of the Lerchs-Grossmann (L-G) algorithm. This gave an indication of the pit sensitivity to price but since other variables also change, some with metal price (perhaps steel and equipment), and some independently (fuel and tires) the understanding of these different pits was restricted. In addition, a run of the program could take hours, making a detailed analysis of small changes unwieldy. The L-G algorithm was programmed by a variety of people and sold as part of commercial mining packages, however it was first and most successfully commercialized by Jeff Whittle in 1984. When Whittle’s 3-D™ was expanded to 4-D the parameterization of the economic inputs was considered and the ability to run a suite of “pit shells” became automatic. The competing NPV Scheduler™ program sold by DataMine™ offers similar pit shell analysis capabilities."

Jan 1, 2018

By Chris Lynagh, Collin Schroeder

Determining the best excavation method is a critical step in successful tunnel construction. In rock tunneling, several factors can dictate the excavation method, such as: (1) rock characteristics, (2) tunnel size and length, (3) nearby utilities/infrastructure, and (4) contractor’s preferred means and methods. This paper discusses the various rock tunnel excavation methods utilized on the Doan Valley Storage Tunnel Project (DVT), a project constructed as part of the broader Project Clean Lake in Cleveland, Ohio. The differences between each method’s initial and final lining, geology, and cycle sequence will be analyzed and compared.

Jun 13, 2023

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By T. Vandergrift, J. Sturgill, W. Gerhard, J. Carrick

As surface minable coal is depleted, many operators look to high-wall mining to extend reserve life. Recent advances in highwall mining equipment have greatly improved productivity, clean coal recovery, and attainable penetration beneath the highwall. Somewhat lagging have been systematic design approaches for ensuring web pillar and overall highwall stability. This paper presents an overview of the design, planning, and field performance of a multiple-seam highwall mining application in southwest Wyoming. The safety and efficiency obtained to date is attributable to the careful geotechnical and operational planning described herein. Field confirmation of performance and suggestions for improvement are also discussed.

Jan 1, 2004

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by complex geometry of the open pit and the surrounding natural topography of an open-pit mine. The resulting inversion cap is known to contribute to the degradation of air quality in the open pit, resulting in loss of production. This paper discusses the development and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the analyzes effect of the geometry of the mine and the slope angle of the pit on the contaminants profiles in the mine.

Feb 27, 2013

By E. A. Domínguez

La Espingarda kaolin deposit was formed by ?in situ? alteration of volcaniclastic rhyolitic rocks belonging to Jurassic Marifil Formation. Three volcanic lithofacies were identified: porphyric biotitic ignimbrites (PBI), a coarse lithic ignimbrite (ILG), a fluidal intrusive rhyolite (RFI), all kaolinized in different degrees. The alteration covers an ellipsoidal area of ~20,000 m2, with its alteration decreasing downwards and disappearing at 8-12 m from the surface. The length to thickness ratio of alteration is 60:1. An erratic silicification was found as small zones (<3 m2) of quartz stockwork. The mineralogy is kaolinite + quartz + feldspars + Fe-oxyhydroxides ± halloysite ± illite and interstratified I/S, although the relative proportions change in each rock type. Due to coarse grain size and high quartz content, natural kaolin is unsuitable for slip cast ceramics, unless beneficiated. Washed ILG kaolin has the best rheological properties and behavior in casting and drying for its mineralogy, particle size distribution, thin texture and surface activity, as well as a certain fusibility and firing kinetics. PBI and RFI kaolins, due to finer texture, smaller grain size, lower surface activity, and higher halloysite amount, have worse slip viscosity and thixotropy that are due also to soluble salts. For the same reason, they have good casting and drying properties, but their purity brings about higher softening temperatures and water absorption. Several parameters are used to discriminate between hypogene or supergene kaolinite genesis. The hydrothermal genesis is mainly sustained by fluid inclusion temperature (150-180ºC) in quartz veinlets, while weathering is supported by deposit morphology, simple mineralogy, kaolinite stable isotopes (d18O ? 18, 13; dD ? ?59; ?85) and paleoclimatic record. It is concluded that a weathering process formed the main alteration with some participation of steam-heated meteoric waters. Neither the contents of Au, Ag, As, Sb, Hg, nor drill data support the existence of any epithermal gold mineralization at the kaolinite bottom.

Jan 1, 2010

By V. Miller

C. Hertzler The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observing a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich II, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69 % Cu vs other rock types with .70 + % Cu; 86 % should be 98.6 %. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness. References McClave, J.T., and Dietrich, II, F.H., 1982, "Statistics," Dellen Publishing Co., San Francisco and Santa Clara, CA, 766 p. Snedecor, G.W., and Cochran, W.G., 1980, "Statistical Methods," The Iowa State University Press, Ames, IA, 561 p. Reply by V. Miller After reading Ms. Hertzler&apos;s comments, it appears that the differences noted were basically semantics. If the paper is ever presented at a math symposium, some changes will be needed. When deciding the best way to present the data to mining engineers and geologists, I decided that presenting the probability that the two sample groupings came from different populations (reverse to the Null hypothesis) was easier and would require less verbage to explain. Hence, the 100(1 - p) difference which was noted. Ideally, I would have preferred to give the recovery and concentrate grades, then comment which ones had significant differences. Unfortunately, Kennecott Corp. did not grant permission to publish the ore body&apos;s actual recoveries and concentrate grades. The conclusion is that there was, as expected, a relationship between the ore&apos;s geologic properties and the metallurgical properties, and by determining this relationship, the overall mineral model was greatly improved.

Jan 8, 1984

By R. K. Mehta

This paper presents the application of a simple genetic algorithm (SGA) to a coal slurry grinding process in order to find the optimum set of conditions under which the desired slurry properties can be attained. The operating parameters of the process were; slurry % solids, dispersant dosage, ball size, and mill speed. The optimization algorithm, which is based upon the mechanics of natural genetics, was used to find near-global optimum points specific to responses measured In terms of fineness, specific energy consumption, viscosity coefficient, and viscosity exponent. In order to minimize the viscosity of the slurry and simultaneously achieve a condition of maximum packing density, optimization was carried out by the penalty method using an overall objective function incorporating several responses. Computer results and analysis demonstrate the ability of the genetic algorithm to perform better than a traditional technique such as response surface methodology (RSM) and to rapidly locate "the global optimum".

Jan 1, 1992

By Girish Roy, Robert Goodfellow, Angel Del Amo, Bingzhi Yang

Designing and constructing tunnels in seismic prone areas present unique challenges to both designers and contractors. The Westside Purple Line Extension Project– Section 3 in Los Angeles requires crossing an active fault that may subject the tunnels to extreme structural demands. In order to ensure that the linings will safely accommodate the fault movement, a revolutionary composite section—steel plate embedded in the intrados of the precast concrete segmental tunnel lining was finally selected. Additionally, continuous expansion steel plates over the circumferential joints will be installed to mitigate the potential opening of the circumferential joints.

Jun 13, 2021

By W. G. Pariseau

Joints may be taken into account when using numerical modeling as an aid to mine design by embedding joints in the model. When using the popular finite element method, say UT3PC, a pre-analysis step is necessary, Step 0. This step is for the computation of equivalent properties of a representative elementary volume of jointed rock (REV) in the model. This Step 0 is taken before Steps 1, 2 and 3 for specification of a rock properties file, generation of the mesh, and model analysis are taken. A brief explanation of equivalent properties and several examples aid in explaining the details of Step 0. Focus is on procedures, input files, and output to show ease of computation. Theoretical details are relegated to references (e.g. Pariseau 2022). Comparisons of safety factor distributions about example mine excavations with direct scaling from mine observations then offer some insights concerning equivalent properties, especially strengths.

Feb 1, 2023

By Aydin Shaterpour Mamaghani, Bilgin. Nuh, Engin Dogan, Tayfun Erdogan

"Improved safety and more environmentally friendly operation are basic advantages of mechanical excavation over the drill and blast method. Raise Boring Machines (RBMs) are one of the types of these machines which have recently been increased use in Turkey. The excavated hole with RBM is more stable than other methods and has better air flow, making it ideal for ventilation shafts. This paper is a summary of the performance of a RBM in the Balya PB-Zn Mine in Turkey. Length and diameter of the ventilation shaft are 200 m and 2.4 m, respectively. The geological and geotechnical characteristics of the strata excavated in the mine are first given and later the validity of a model developed to predict the machine performance is discussed. It is believed that the results of this study and the model given to estimate the performance of the RBM will be useful guide for future applications. INTRODUCTION Raise boring technology was developed to meet the demands of the mining industry, but has also found numerous applications in tunneling or infrastructure projects for ventilation purposes. Raise boring machine uses a small diameter drill rod, around 230-350 mm to drill a pilot hole down to the required depth up to around 2000 m. Once the pilot hole has been drilled to the desired depth, a reamer of up to 9 m diameter is attached to the drill rod. The reamer is then pulled back up to the upper level, creating a round shape. Continues operation provides a faster advance rate than other methods. RBMs are suitable both in hard and soft rock. The flexibility in different angles and diameters is a great advantage compared to drill and blast excavation method. RBM creates a shaft with smooth walls which usually does not require lining. The hole is more stable than a drilled and blasted method and has better air flow, making it ideal for ventilation shafts. Raise boring is convenient method in competent rock; however several problems are faced in geological formations where geological discontinuities are dominant. Moreover, assembly and disassembly time may be long in some cases. The performance and operational parameters of the excavating machine should be predicted prior to starting the excavation operations in order to fulfill the economic requirements of the project. In the light of this fact, the main objective of this investigation is to summarize a case study on raise boring machine performance and suggest a new model based on laboratory test results. First, general description of the mine and project are provided. Then, the physical and mechanical characteristics of the samples taken from project area are discussed. In the third section, performance and operational parameters of RBM are investigated to understand the machine behavior in different rock characteristics and also to collect a useful database for further investigation. In the fourth section, a new model for performance estimation of RBM are recommended."

Jan 1, 2016

By A. M. Whiting

Competition for coal producers and their primary customers has constantly increased during recent years. The effects of the Clean Air Act Amendments of 1990 on the electric utility industry, coupled with the normal complexities of coal production, quality control, transportation and contracting techniques have spurred both buyers and sellers to increase their level of sophistication. This paper will review the basic aspects of the U.S. coal business and explore the commercial approaches which have proven to be most successful.

Jan 1, 1994

A case study of a systematic approach to grinding circuit steady-state optimization is presented. After overall review of the flowsheet, two circuits were prepared for detailed testing. Functional performance analysis was chosen as the primary modelling system, and on this basis a quality assurance program for data gathering was implemented. A number of circuit design and operating variables were experimented with statistical analysis of plant test results revealed relationships previously unquantifiable by any other modelling technique. Improvements in classification system and mill grinding efficiencies were demonstrated and significant energy cost savings thus realized.

Jan 1, 1998

By J. Choi

For the first time, the influence of stearyl trimethyl ammonium chloride (STAC) as a collector, on the flotation behavior of lepidolite (Uljin, South Korea) was systematically examined in Denver Sub-A cells. Flotation tests were carried out by varying amount of STAC (50?200 g/ton), feed size (-65, -100, -150, and -200 mesh), and solution pH. The impeller speed of 1000 rpm, flotation time of 10 min and AF-65 (a frother) of 250 mL/ton were invariably applied. In order to complement flotation experiments, zeta potential measurements and XRD analysis were conducted. XRD results showed that the ores were mainly composed of lepidolite, muscovite, quartz, calcite and albite. In addition, zeta potential results showed that isoelectric points were about 2.5, 2.3, and 9.7 for quartz, albite, and calcite, respectively, and lepidolite was determined to be less than 2. Overall, the results of 3-stage flotation showed that Li2O grade and recovery tended to increase with increasing STAC dosage and decreasing feed size. In addition, Li2O grade increased with decreasing pH. The results were explained by the extent of the interaction between STAC and each mineral.

Feb 23, 2014

By R. L. Grayson

A goal programming-based worker scheduling model has been incorporated in the Mine Management Support System (MMSS) for assigning workers to prioritized jobs on a shift basis. In the model the accomplishment of each regular and non-regular job is a goal. The objective is minimization of the deviations away from the goals. A number of coefficients are used as premultipliers of the decision variables in order to address practical considerations associated with the utilization of workers and the requirements of jobs. Some of these premultipliers will be updated expertly within MMSS, timely updating the statuses of the dynamic parameters.

Jan 1, 1991

By Sidney A. Suhler

The persistent requirement for methods and equipment capable of detecting hazardous anomalies in advance of underground mining has led to the development by the U.S. Bureau of Mines of a directional radar probe. The probe operates from boreholes drilled from the surface into the underground region to be mined. The engineering model radar was completed in early 1982 and field demonstration tests were performed in May of that year at a selected coal mine. Preliminary in-situ electromagnetic tests were performed at several candidate coal mines to evaluate the radio-frequency characteristics of the coal. A coal mine in New Mexico was selected on the basis of low EM propagation losses in the coal and the presence of an extensive coal seam displacing fault as a radar target. The borehole radar was operated in two vertical boreholes which intersected the coal seam at approximately 25 and 40 feet from the fault interface. Radar reflections from the coal/ rock interface were detected in both tests. Underground tests in a horizontal borehole in the coal were less successful because of interfering reflections. Additional borehole-to-borehole tests were performed with a separate ground penetrating electromagnetic system to obtain radar range calibration data. The coal was found to be bounded by very lossy roof and floor sandstone and shale while propagation through the coal seam was obtained at distances up to 175 feet between test boreholes. Coal seam continuity was indicated by the hole-to-hole experiments through a section of the seam previously thought to be completely cut off by the fault.

Jan 1, 1983

By M. Kalin, H. D. Sharma

INTRODUCTION The inactive uranium mill tailings investigated in this study are located in two mining districts, Elliot Lake and Bancroft, Ontario, Canada. The sites exhibit a mixture of surface features consisting of dry areas, with or without vegetation and areas covered with water. On the edges of the water bodies, indigenous vegetation has invaded the tailings beaches [ Typha] spp. (Tourn.) L. a dominant plant on these tailings beaches, has been studied for the uptake of radium-226 and lead-210 (Kalin and Sharma, 1981b) from the tailings. It was found that most of the radium-226 remains in the roots of the plants, and that the solubility of radium-226 in control soil differs from that in tailings. The uptake of radium226 by vegetation and other biota is related to the solubility of the element in water. Factors controlling the solubility of radium-226 in uranium mill tailings are of interest in assessing the environments effects of these wastes. Rusanova (1962) found that the soluble or extractable amount of radium from the soil is inversely related to the total concentration of calcium and magnesium in the soil. Experimental work has clarified some aspects of the leachability of radium from uranium mill tailings (Levins, et al., 1978; Wiles, 1978, and others). Halvik, et al., (1967) studied the effects of pH and chemical composition of surface water on the liberation of radium from uranium mill tailings and uranium ore. He found that an increase in pH, up to a value of pH 9, decreases the amount of radium released from the tailings and the ore. A positive effect of calcium chloride was noted on the leachability of radium. Benes (1981) reviewed the physicochemical forms of radium and its migration in water. Based on experimental work, he identifies primary factors which determine leaching of radium from uranium mill tailings. The ratio of the volume of the leaching solution to the weight of the leached sample; the composition of the leached solids and the leaching solution, and finally the pH of the leaching mixture are of importance. He emphasized that a scarcity of field data exists, which would relate experimental work to the actual situation in the tailings ponds. Inactive tailings ponds in Ontario are 16 to 23 years old, and processes which are of importance in evaluating the long term effects of uranium mill tailings in the environment can be studied. The objective of this work was to investigate the leachability of radium-226 from the tailings under field conditions. MATERIALS AND METHODS Sample Collection A description of inactive tailings sites in Ontario, where the tailings and the water for this study were collected, can be found in a report by Kalin (1981). [Typha] spp. specimens were excavated from 16 different locations along with the tailings attached to the roots of the plants. A tailings sample from the surface area, around the plant, was secured before the excavation. Tailings samples were also collected from dry areas free of vegetation in the vicinity of the wetland stand. Surface samples (depth 0-5 cm) and samples at a depth of 20-25 cm were secured. Water was collected from the shallow tailings beaches around the vegetation stands. Sample Preparation The roots of the plants were washed free of tailings with distilled water. The resulting thick slurry of tailings was allowed to settle in the wash basin for five minutes and the supernatant water was decanted. The remaining saturated tailings were brought to 400 ml volume with distilled water in a beaker. The slurry was mixed with a magnetic stirrer for two 24-hour periods. After the first 24-hours, the slurry was allowed to settle for 20 minutes and the supernatant water was removed. The remaining sediments were suspended again in distilled water (400 ml total mixture) and leached for a second 24hour period. The tailings slurries from the different locations had a solid to liquid ratio, which ranged from 0.5 to 1.4 grams of dry tailings material per millilitre. The variations in the ratios are the result of differing fractions of coarse and fine tailings on the sites. In the final leachates, the solid to liquid ratios of the samples were 0.17 (±0.1) g/ml. The pH of the surface water and the leachate was determined with an I.L. Portomatic pH meter. All the tailings samples were homogenized in a mortar and brought to dryness at 75 to 85°C. Approximately 0.5 g of tailings were

Jan 1, 1981

By J. R. Dyni

Colorado nahcolite deposits, estimated at 29 billion metric tons, formed in an asp metric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCOg) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62 percent), disseminated crystals (24 percent), and impure beds (14 percent). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1980