Search Documents

By Ralph H. Light

The recent surge in demand for uranium in the United States, accompanied by a significant increase in price, has resulted in exploration, mining, and milling of lower grade ores than have been exploited in the past. To sustain production levels of uranium with lower grades of feed requires larger tonnage mill operations. Also, because of recent environmental regulations, mill operations must be prepared to properly contain large tonnages of tailings, and recycle, treat and discharge, or evaporate mill effluents. Thus, the advent of lower grade ores, larger tonnage mills, and environmental considerations has made the cost of milling a critical factor in today's uranium production economics in the United States. Three basic milling methods are employed for extracting uranium from ores: 1. Acid leach, countercurrent decantation, and solvent extraction. 2. Acid leach, resin-in-pulp, and Eluex. 3. Alkaline leach, solid-liquor separation, and precipitation. Vanadium often occurs as a valuable by-product in ore deposits located in the Uravan mineral belt in Western Colorado. Also, lesser amounts of vanadium may occur in ores from South Dakota, New Mexico, and Utah. Vanadium is usually extracted in the acid leach solution with uranium and recovered by solvent extraction after recovery of the uranium. By-product recovery of uranium from phosphoric acid and porphyry copper dump leach solutions is now receiving considerable attention. Pilot plant studies are under way and construction of commercial plants is in progress.

Jan 1, 1977

By Z. Man, X. Zhu, Y. Xian, Y. Tao

"Fine coal separation has been always concerned. The froth flotation is not efficient in desulfurization because of the low rate of sulfide liberation from raw coal, the natural hydrophobicity caused by sulfur concentration on the surface of sulfide, and the presence of large amounts of middling feed. An efficient centrifugal gravity separator was employed to separate for Shandong –0.5mm high sulphur coal, the partition curve of centrifugal separator was obtained with conclusion that the Ecart probable error value of the separator is 0.095, the imperfection I value is 0.128. Finally, comparing with the coal flotation using progressive release method, the result shows that the effect of the desulfurization with centrifugal gravity force field based on density difference between coal and minerals are much better than that of the floatation which operates based on the difference in surface properties. It provides a efficient technical way for fine coal separation. INTRODUCTION Coal plays the most important role in the energy consumption in China. Although natural gas, wind energy, nuclear power has made great progress in recent years, but the share of coal in the final energy consumption accounts for 70-80%, which is determined by energy storage of China. Under the requirement of environmental protection, the clean utilization of coal resources becomes more and more important, and the need has already been identified. Coal washing and processing plays an important role in the process of high-efficiency and clean utilization of coal. For the separation of fine coal, flotation is a traditional method for effective separation and has been used in large scale industrial applications in coal preparation plant. However, for the separation of difficult-to float coal, especially fine oxidized coal and low–rank coal with hydrophilic surface, flotation is usually inefficient [1-3]. Although many pretreatment methods have been adopted, including grinding, microwave pretreatment, new flotation reagents, the problem of efficient separation has not been completely resolved [4-6]. Thus, an enhanced gravity separation method using particle density difference rather than hydrophobic difference was proposed for the separation of fine coal. Many research results have proved that this is a practical and effective method of sorting. R.Q. Honaker used Falcon C10 concentrator, Knelson centrifugal separator and spiral separator to clean the fine coal with size of 600*210 µm and 210*37µm, the effects of different operating parameters on the separation index was discussed. The results show that the separation density of Falcon can reach 1.6, and the Ep value can reach 0.1-0.15. This paper revealed that for the separation of fine coal with high sulfur content or fine grained content. Falcon has high separation efficiency with low cost. Separation results present in another paper showed that the desulfurization efficiency of inorganic sulfur was better than that of flotation [7-8]."

Jan 1, 2017

By L. D. Patts, S. J. Janisko, E. G. Cauda, A. D. Bugarski, G. H. Schnakenberg, J. A. Hummer

Filtration systems with disposable filter elements (DFEs) are used in the underground coal mining industry to control particulate matter emissions from diesel-powered permissible and nonpermissible coal mining equipment. This study was conducted in underground mine conditions to evaluate three types of high-temperature DFEs used in those filtration systems. The DFEs were evaluated for their effects on the concentrations and size distributions of diesel aerosols and concentrations of nitric oxide (NO) and nitrogen dioxide (NO2). Those effects were compared with the effects of a standard muffler. The experimental work was conducted directly in an underground environment using a unique diesel laboratory developed in an underground experimental mine. After an initial DFE degreening period, the filtration system with all three DFEs was found to be very effective at reducing total mass concentrations of aerosols in the mine air. The effectiveness of DFEs in filtering aerosol mass was found to be a function of the engine operating conditions. The efficiency of the new DFEs significantly increased with operating time and buildup of diesel particulate matter in the porous structure of the filter elements. A single laundering process did not exhibit substantial effects on the performance of the DFE elements. The effectiveness of DFEs in removing aerosols by number was strongly influenced by engine operating mode. The concentrations of nucleation mode aerosols in the mine air were found to be substantially higher for DFEs when the engine was operated at high-load modes rather than at low-load modes. Initial heating of certain DFEs resulted in visible white smoke and substantially elevated aerosol number concentrations. The effects of the DFEs on the total concentration of nitrogen oxides (NOX) were found to be minor. The NO2 fraction was found to be generally lower for the DFEs than for the muffler. The engine-out NO2 fraction of the total NOX was found to be substantially higher for low-load modes than for high-load modes..

Jan 1, 2011

By J. W. Shield

Refractory sulfide flotation or gravity gold concentrates are coated onto a sized support matrix and placed in a heap configuration for biooxidation. The surface coating is typically less than 0.05 in. thick and the support matrix is preferably composed of 0.375 to 0.75 in. diameter material. The exposed thin coating of sulfides reduces biooxidation rate limitations due to oxygen mass transfer. The large spaces between matrix particles reduce resistance to fluid percolation and aeration in the heap. The capital and operating costs for this biooxidation configuration are significantly less than for concentrate biooxidation in stirred tanks. After 30 to 90 days of biooxidation, sub- sequent gold recoveries exceed those seen in whole ore heap biooxidation and are comparable to recoveries obtained from stirred tank biooxidation processes. Results from laboratory and pilot testing indicate that this technology is a viable alternative for pretreating sulfide refractory gold ores.

Jan 1, 1997

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By Vern Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western porphyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized -1+1/2-inch (-2.5+1.3-cm) ores from the Kingston (0.9 pct CU) and Centennial (1.6 pct Cu) mines of Upper Michigan. Concentrates of 4.0 pct and 7.5 pct Cu, respectively, were obtained at recoveries of 85 and 80 pct of the copper in the feed. Eighty percent of the sorted ore was rejected as tailing. Sorting larger fragments improved the separation efficiency. Tests on -4+2-inch (-10+5-cm) sized Kingston (1.6 pct Cu) and Centennial (2.1 pct Cu) ore samples yielded concentrates of 4.3 and 4.5 pct Cu, respectively, with corresponding recoveries of 92 and 91 pct. About 60 pct of the sorted ore was discarded as tailing. Porphyry copper sulfide ores also responded to electronic sorting but at a lower separation efficiency. Sorting response was affected by the degree of segregation.

Jan 1, 1976

By Tony Szwilski

A correlation between the rank, ash content and coal seam discontinuities and coal strength/stiffness is discussed. Rebound hammers were used to evaluate the strength properties of two coal seams. The coefficient of variability of the rebound tests are compared with those of laboratory compressive strength tests by other investigators.

Jan 1, 1985

By J. B. Goddard

Abstract. Leaching of, uranium in situ from sandstone deposits with ammonium carbonate solution containing: dissolved oxygen occurs rapidly compared with the leaching of the bulk of the sulfur present as FeS2. However because of their high reducing, capacity and their relative abundance, the FeS2 minerals consume; the bulk of the oxidants A pressure leach apparatus was-construtted which permitted the measurement of oxygen consumtion by FeS2. Oxygen consumption by FeS2 is best described by a first-order reaction. The experimental rate constants for various cores are roughly proportional to their FeS2 contents.

Jan 1, 1980

By James F. McConnell

Federal and State sulfur oxide emission and ambient air quality regulations have been implemented to fulfill the requirements of the Federal Clean Air Act Amendments of 1970. Primary and secondary air quality standards have been established at levels considered necessary to assure the protection of the health and welfare of the public. Standards of performance under this Act have been established to control the rate of sulfur oxide emissions from individual sources so as to protect and to improve the quality of the Nation's air. The new source standards of performance were made rigorous for large coal burning stationary sources. This has had a severe impact on the electric utilities that operate the coal fired steam electric plants which are the largest consumers of the Nation's coal production. States have taken different approaches in State Implementation Plans (SIPS) as approved by the Federal Environmental Protection Agency. Some states, such as Pennsylvania, have chosen to permit moderate SO2 emission rates from existing sources which are not in critical air basins. All are required to meet primary and secondary air quality standards and to limit sulfur oxide emissions from new large stationary sources to a minimum of 1.2 LBS of S02/MMBTU fired. This re- quires a fuel sulfur percentage of about 0.7 for a 12,000 BTU/lb coal. In an effort to develop strategies and technologies to conform to performance standards while continuing and hopefully expanding the utilization of the Nation's coal supply, the electric utilities, the Federal and State regulatory agencies, and other industries and government agencies are considering several alternatives. 1. Natural low sulfur coal 2. Flue gas desulfurization - (FGD) non-regenerative and regenerative 3. Coal gasification 4. Liquefaction and solvent refined coal 5. Fluidized bed combustion 6. Chemical coal cleaning 7. Physical coal cleaning Of these options, only the first and the last can be considered to be widely used in full commercial practice at this time. FGD has certainly demonstrated technical and operating feasibility and is close to being in full commercial practice but it remains to be seen if the large systems under construction are economically and environmentally optimum.

Jan 1, 1975

By Staff

In 2012, the estimated value of mineral production increased in the United States for the third consecutive year. Production and prices increased for most industrial mineral commodities mined in the United States. While production for most metals remained relatively unchanged, with the notable exception of gold, the prices for most metals declined. Minerals remained fundamental to the U.S. economy, contributing to the real gross domestic product (GDP) at several levels, including mining, processing and manufacturing finished products. Minerals? contribution to the GDP increased for the second consecutive year. Trends in other sectors of the domestic economy were similar to those in mineral production and consumption rates (Table 1). After continued decline following the 2008-2009 recession, the construction industry began to show signs of improvement late in 2011 and throughout 2012, with increased production and consumption of cement, construction sand and gravel, crushed stone and gypsum, mineral commodities that are used almost exclusively in construction.

May 1, 2013

By Amanda Powers, Brian Glynn, Robert Sauceda, Daniel Huffines, Mike Garbeth

This paper will review the evaluation performed for the Cottonwood & Hackberry Creek Wastewater Interceptor Improvements Project to replace two separate aging and undersized interceptor sewers by either open cut construction or trenchless construction methods. A case study will be discussed for the utilization of microtunneling to avoid a deep open cut excavation within a landscaped roadway median to construct nearly a mile of new 60-inch interceptor sewer in an urban area adjacent to an environmentally sensitive riverine area, while minimizing the permitting and environmental impacts of construction, and minimizing the impacts to residents and vehicular trafc and restoration reuirements.

Jun 23, 2024

By Ayokunle Adewale Akinlalu, Sunday Bayode, Sherif Olumide Sanusi, Joshua Oluwagbenga Adeboye

Gold occurrences have been reported in Alagbede, southwestern Nigeria, but a mineral potential map (MPM) to guide academics and investors in the area is still needed. As a result, geophysical methods (aeromagnetics and aero-radiometry) have been used to assess the potential for gold minerals in the area. Several enhancement filters, such as reduction to the equator, upward continuation, analytical signal, second vertical derivative, and power spectrum analysis, were applied to the aeromagnetic data to understand the subsurface geology better. The enhancement filters applied to airborne radiometry data are K/eTh, ternary color composite, F parameter, and deviation from the ideal K values (Kd). Geophysical data analysis was used for structural mapping and geological reconstruction, while aero-radiometric data was used for hydrothermal alteration mapping. The primary trend observed in the area’s magnetically inferred structural framework map is NE-SW, while a few are in the NW–SE and E-W trends. These observed trends show that the study area suffered at least three deformation episodes. Geological evidence of gold mineralization, such as favorable lithology, geological structure, and hydrothermal alterations, has been fused to produce a reliable MPM of the area. The geographical location of the existing mineral sites in the investigated area agrees with the geological structures and the MPM produced there. Thus, the systematic approach adopted in this study can be extended to other supracrustal belts of a typical Precambrian basement complex worldwide to ensure the reliability of orogenic gold mapping and resource management.

May 9, 2023

By S. S. Klima, H. Jiang, T. W. Beck, Y. Zheng

Researchers at NIOSH’s Pittsburgh Mining Research Division (PMRD) performed comparative testing of six different water sprays at pressures ranging from 689 kPa (100 psi) to 6,895 kPa (1,000 psi) in a 14.5-m3 (512-ft3) confined dust chamber. Testing was conducted to determine the effect of various pressures on each spray’s respirable coal dust knockdown ability. It is known that higher water pressures are typically preferred for lowering airborne dust concentrations, but it was important to determine at what pressure range the dust knockdown ability of each spray plateaus or reaches its minimum dust concentration. Results from this testing showed that several sprays saw up to 100% decrease in dust concentrations during the five-minute water spray testing period, with some occurring well below the maximum 6,895 kPa (1,000 psi) spray pressure.

Feb 1, 2023

By S. K. Pan, R. Venugopal, L. A. Kumaraswamidhas, Rakesh Prasad, Chandan Pandey

Cold compressive strength (CCS) and apparent porosity (AP) of pellets are essential properties regarding the burden of blast furnaces. The optimal required values for industries are 2.5 KN CCS and 21% AP. Blaine fineness and firing temperature are the decisive parameters analyzed here. During firing, microstructure phases such as silicate, hematite, and pore are formed. The phase’s grain density during induration influences the pellet’s CCS and AP. The influence of the factors over the response is evaluated by I-optimal (response surface methodology) design. Blaine fineness, firing temperature, pore phase grain density (PPGD), silicate phase grain density (SPGD), and hematite phase grain density (HPGD) affect the CCS and AP of pellets. The RSM-I-optimal predicted responses with a coefficient of determination (R2) of 0.89 for CCS and 0.91 for AP of iron ore pellets. Optimal conditions were Blaine no. = 1668 cm2/g, 1250 °C firing temperature, PPGD value 90 no/mm2, SPGD value 250 no/ mm2, and HPGD value 490 no/mm2, with 4.5 KN CCS 27%. The induration processes were investigated through statistical design of experiments for process optimization. Statistical analysis indicated the direct and interactive influence over CCS and AP. In this study, RSM-I-optimal modeling is used for iron ore pellets processing. The I-optimal prediction could be applied to make the process economical because information is obtained through fewer experiments.

Aug 18, 2020

By N. W. Johnson

Two analysis tools which have been applied to problems in industrial Flotation processses are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. The paper describes practical examples of the application of kinetics to examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.

Jan 1, 1985

By William D. Mayercheck

Beginning in 1974, the Bureau of Mines, U.S. Department of the Interior, sponsored R & D efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The U.S. Department of Energy continued this effort as of October 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems or components now being built, surface tested, or tried underground.

Jan 1, 1981

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1990

By D. S. Yantek, L. A. Alcorn, M. J. Lowe, H. E. Camargo

U.S. National Institute for Occupational Safety and Health (NIOSH) studies show that 43.5% of surveyed coal preparation plant workers had noise exposures exceeding the U.S. Mine Safety and Health Administration permissible exposure level of 90 dB(A). Sound levels around vibrating screens in these plants often exceed 90 dB(A). NIOSH is currently developing noise controls for horizontal vibrating screens. To characterize noise sources, NIOSH researchers performed sound pressure level (SPL) measurements on a vibrating screen at their Office of Mine Safety and Health Research laboratory in Pittsburgh. The results show that the entire screen contributes to noise below 1 kHz, and the vibration mechanism housings are most significant above 1 kHz. Constrained layer damping (CLD) treatments and an enclosure were used to reduce mechanism housing noise in this range from 1-10 kHz. These were evaluated using sound power level measurements according to ISO 3744. The CLD treatments reduced the A-weighted sound power level by 3.1 dB in the 1 to 10 kHz one-third-octave bands. A panel-on-frame vibration mechanism enclosure using various types of panels further reduced the A-weighted sound power level from the CLD configuration in the 1 to 10 kHz one-third-octave bands by 3.7, 4.0, and 3.9 dB for aluminum, steel, and Dynalam™ panels, respectively. The combination yielded a 7 dB reduction from baseline in A-weighted sound power for the same frequency range.

Jan 1, 2011

By B. R. Reddy, P. V. R. Bhaskara Sarma

A process for the separation and recovery of cobalt and nickel was optimized for a sulfate leach solution of Indian Ocean sea nodules containing 80 g/m3 cobalt and 730 g/m3 nickel using the sodium salt of Cyanex 272 as the extractant. Extraction of both cobalt and nickel increased with an increase in equilibrium pH and extractant concentration. The extracted species with respect to cobalt appears to be CoA2.3HA. More than 99.6% extraction of cobalt was achieved using 0.04M solvent in a three-stage counter current simulation at the A:O phase ratio of 3:2. The co-extraction of nickel was about 0.6% only. Two-stage countercurrent stripping of cobalt from the loaded organic at an A:O ratio of 1: 7 resulted in a pregnant electrolyte enriched by 0.8 kg/m3, thus enabling a ten times overall enrichment of cobalt. From the cobalt free raffinate, nickel extraction was carried out using 0.25M solvent in two countercurrent stages, and the extraction showed a 99.8% recovery. Stripping of nickel from the loaded solvent was carried out at an equal phase ratio with the advance electrolyte of pH 1.75 in two countercurrent stages. The nickel stripping efficiency was found to be 98.8%. The present studies indicated that complete recovery of cobalt and nickel was possible using nine counter-current stages.

Jan 1, 2002