Search Documents

By Ven Mercade

The flotation of calcite has been studied by many investigators, especially in terms of type of collector; pH; and metal ions that activate and, more importantly, depress the flotation of calcite (1)(2). Research was extended to the investigation of the effect of polyvalent metal salts and sodium silicate using these materials added separately or in mixtures (3)(4)(5)(6). Flotation of calcite was also studied with respect to its function as a carrier in the beneficiation of kaolin clays by Ultraflotation (7) (8) (9). The carrier used in Engelhard Minerals & Chemicals Corporation's industrial Ultraflotation operation is calcite. This fact, coupled with the continuing interest in Ultraflotation phenomena, led to a study to determine the effect of polyvalent metal-silicate hydrosols on the flotation of calcite.

Jan 1, 1978

By Ossi V. I. Hintikka

There are several limestone deposits around the Lohja area in southern Finland. Raw material for cement rock is mined from some of them. The formations are geologically complicated, and therefore selective mining is used whenever possible. One of these mines is the Tytyri underground limestone mine, which is divided into two parts; Törmä and Solhem. In addition to the selective mining system hand sorting or picking must be used at the Tytyri mine to improve the overall grade of the blended limestone. Some means were needed in order to improve the quality and to increase the feed rate by the elimination of hand sorting. Sorting machines were considered and eventually a Sortex 811MW was pilot plant tested at the Ojamo mine near Tytyri. This machine now continues to be used on production.

Jan 1, 1971

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By E. Stemn

Incident investigation is of utmost importance in most high-risk industries. This study was undertaken to study the content of past investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of 5 elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of 3 Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed. INTRODUCTION The importance of learning from incidents is well documented in the literature. For instance, some scholars regard learning from incidents as important for improving safety [1,2]. Thus, many organisations spend considerable resources in identifying lessons from incidents and subsequently on the process of improvement that follows the identification of lessons. It is therefore important for such organisations to determine the effectiveness of their learning from incidents processes, in order to identify specific areas where improvements are needed, so that interventions can be as specific as possible. The learning from incidents process models the plan-act-check-do approach of management systems, often consisting of four major stages, namely; data collection and incident analysis, planning interventions, implementing interventions and follow-ups and evaluation [3,2]. The investigating and analysis of incidents have been regarded as one of the vital stages of the learning process since it is the stage where lessons are identified [3,2,4]. It has also been noted elsewhere in the literature that results of the previous stage of the learning process are important for the next stage [3]. For example, ineffective incident analyses could result in the planning of ineffective remedial measures. One of the primary aims of incident investigations is to identify lessons from previous incidents which when implemented can prevent future recurrences or minimise the effects of future incidents. There is thus the need for organisations to assess the quality of their investigations periodically since it is one of the means they adopt to improve safety and the quality of remedial measures to some extent depends on the effectiveness of the investigations. Although previous studies [5,2] have assessed the effectiveness of the learning process, and some aspects of the learning process, such as incidents reporting, there is less focus on the effectiveness of incident investigations. The research described in this paper was therefore conducted to contribute to this gap, focusing more closely on incident investigation reports.

Jan 1, 2019

By Ravindra M. Chhatre

Uranium associated with phosphate deposits has been the subject of numerous investigations (1-8). In the land-pebble phosphate deposits of central Florida, uranium is found in the phosphate matrix (ore) and in the leached zone between the over-burden and matrix (1). Between 0.01 to 0.02 percent uranium is found in the leached zone, which consists of apatite and aluminum phosphate minerals (crandallite, wavellite, millisite) (Z). The primary phosphate mineral in the matrix is apatite, and the 0.005 to 0.01 percent uranium typically found in the matrix is associated with this mineral (1). It is generally believed that uranium substitutes for calcium in the apatite structure (3-5). Clay and quartz phases associated with phosphate deposits contain little uranium (1, 6), and no descrete uranium minerals have been detected in these deposits (4). A typical phosphate matrix consists of quartz, slimes (-150 mesh material) and recoverable phosphate. When the matrix is beneficiated, partition of uranium and radium takes place (9, 10). Although considerable data exists on how uranium is distributed in the phosphate deposits, no systematic study has recently been reported on the distribution of uranium during phosphate rock beneficiation. The purpose of this study was to determine how uranium is distributed in the various strata which comprise the overall land-pebble phosphate deposits, as well as how the uranium is redistributed during beneficiation of phosphate matrix. To obtain this information studies were carried out on matrix samples obtained from three different mines in central Florida. Using pilot-plant scale beneficiation, an analysis was performed on how uranium in the matrix is distributed among the pebble fractions, flotation concentrates, flotation tails, and slimes. The uranium level profile for an active mining area was also obtained. Also, since thousands of acres of slime ponds may someday become a source of both phosphate and uranium, a depth versus uranium content profile was determined for an inactive slime pond.

Jan 1, 1978

By J. K. Hrica, T. J. Orr, J. Navoyski, B. Macdonald, C. L. Hoebbel, J. L. Bellanca, B. Demich

Haul truck fatal accidents and injuries continue to be a significant concern for the mining industry. However, the availability of high-quality training materials continues to be limited. Near-miss incident accounts, if packaged well, could help fill this gap, because for every fatality, there are hundreds of reportable accidents and thousands of undocumented near misses. Researchers from the National Institute for Occupational Safety and Health (NIOSH) collected detailed accounts of 21 near-miss incidents in virtual interviews with mineworkers at surface mining operations across the country. From these interviews, researchers created four simulation videos. The videos bring these events to life through first-person retelling and various visual perspectives of actual events. Each video exemplifies a critical safety message and a common haul truck hazard. This paper describes the process of taking narratives and turning them into impactful visual stories. NIOSH plans to co-release these simulation videos with the Mine Safety and Health Administration (MSHA) to the mining industry to raise awareness and ultimately help reduce haul truck-related accidents and fatalities in mining.

Feb 1, 2023

By Christophe Bragard, Marte Gutierrez, Haotian Zheng, Michael Mooney

This paper proposes a framework for applying surrogate-based approaches to evaluate SEM construction, which can both benefit the uncertainty analysis in the design stage and real-time calibration during the construction process. The performances of four surrogate modeling approaches, namely back-propagation neural network (BPNN), support vector regression (SVR), random forest (RF), and polynomial chaos expansions combined with Kriging (PCK), were evaluated and compared. A variance-based global sensitivity analysis (GSA) was performed on the surrogate predictor to quantify the impacts of geotechnical parameters on the deformation responses induced by SEM tunneling. The Regional Connector Crossover Cavern project constructed in Downtown Los Angeles was set as the benchmark problem to demonstrate the efficiency and reliability of the proposed procedure.

Jun 13, 2021

By J. B. Malcolm

The discovery of tungsten-bearing quartz outcroppings in Vance County, N. C., by the Hamme brothers in 1942, made international news in the mining industry and was, in fact, one of the major ore discoveries made in the U.S. during the last 25 years. Operations began at the Hamme mine in 1942, but after 16 years of successful operation, the mine was closed down in 1958 under adverse market conditions. By that time, it had produced nearly 20 million lbs of metallic tungsten. Because of the square-set timber mining method then in use, mine operating expenses were high, actually representing 78% of the total operating expenses at the property. In timber work alone, 160 men were employed. Approximately 500,000 bd ft of timber were placed monthly at a direct supply cost of $1.00 per ton of ore mined. Late in 1959, following a slightly improved position in the tungsten market, company management decided that, by changing the mining method, the operation could be economically feasible. The major premise in this decision was that a reduction of from 25 to 30% of the mining costs could be achieved by the conversion of the mining method from square-sets to horizontal cut and fill. Reopening of the mine began in February 1960, Full production has now been reached and overall mine productivity has been doubled.

Jan 1, 1962

By Harvey P. Knudsen

This paper illustrates the application of geostatistics to a roll front type uranium deposit located in Wyoming. The steps involved in calculation of experimental variograms, variogram modeling and verification of the resulting models are described in detail. The resulting spherical variogram models for grade thickness and thickness show strong geometrical anisotropies. The major axis of anisotropy for both variables is approximately parallel to the axis of the roll front and the minor axis perpendicular to the roll. This model confirms the technique of drilling "fences" across the roll front, where the drilling is much closer together than the fences along the roll.

Jan 1, 1978

By Patricio Vergara Lara, Jorman Barrera

The selection of the production level elevation is one of the most critical strategic decisions faced by large-scale block or panel caving projects. This elevation largely affects project timelines, capital expenditures, resource recovery, and may even constrain the mine’s maximum production capacity. Over the years, many computational tools have been developed to assist in this decision, most of them based on the same principle of maximizing the project value given its production level elevation. However, for large and inclined deposits, or those extending significantly in the vertical dimension and where extraction cannot be achieved from a single level, traditional selection techniques involving multiple production horizons often lead to suboptimal results. This paper proposes a methodology ensuring that the selection of production level elevations in a multiple horizons (“lifts”) case is globally optimized. Input parameters include economic and cost variables, maximum extractable column height, and deepening costs. The methodology is demonstrated through a real case study to illustrate its potential impact on project value.

Feb 22, 2026

By R. L. Loofbourow

Most wet mines face unquantified water costs as well as the obvious wing costs. Both kinds of cost are multiplied by work at greater depth and by higher unit prices. This intensified challenge merits renewed or perhaps altogether new response. Any practicable way to reduce inflow tackles both obvious and unquantified costs. Ten groups of possible ways to do it are cited. Most have been demonstrated. Two are known from work other than mining. Surely new means can be found. Here are opportunities for operators of wet mines!

Jan 1, 1980

By Ekkehart Mertins, Hans-Dieter Wasmuth

During the last years many new concepts have been presented for magnetic separation of feebly magnetic minerals by using the new high-duty permanent magnetic material especially in Open Gradient Magnet Systems (OGMS). In this respect KHD Humboldt Wedag AG developed an improved version of a drum-type magnetic separator called PERMOS® with a special magnetic field configuration for the NdFeB permanent magnets, which gives a magnetic field strength of at least 0.7 Tesla and a wide working zone outside the drum. The magnet system within the PERMOS® unit is no longer made of relatively large magnet blocks of alternating radial magnetisation; the system is now made up of a multitude of small NdFeB bars with a specially oriented magnetisation. This PERMOS® Open Gradient Magnetic Separator can be used for dry magnetic separations in "top-feed" and 'free-fall" feed configuration as well as in the conventional wet "drum-type" feed mode. It allows high throughput rates of up to 40 metric tons of solids per hour and meter of drum length without any clogging problems, even when strongly magnetic com-pounds are present in the feed material. The important design features and the actual machine characteristics of the improved PERMOS® units for dry and wet magnetic separation are described and typical examples for their commercial application for industrial minerals and for martitic iron ores are presented.

Jan 1, 1995

By J. Fuller, J. Beale, Q. Justice, Z. Agioutantis, S. Hicks, Z. Khademian

Seismic events can be induced by mining due to unstable rock failures or slips along geologic structures leading to the sudden release of strain energy stored within the rock near underground openings. Depending on their intensity and proximity to the working area, seismic events may raise safety concerns, and thus the forecasting of the seismic potential in advance of mining can mitigate safety hazards. The integration of seismic data into geomechanical modeling can provide a tool for identifying areas with elevated potential for seismic activity. In previous works, a methodology was developed to forecast seismic potentials in a pseudo-2D geomechanical model. In this paper, seismic events, ranging in magnitude from about -1.0 ML to 3.7 ML, recorded in a deep longwall mine (> 450 m) in Virginia during mining of six adjacent panels, were evaluated to identify areas where larger magnitude events (> 1 ML) had occurred. A three-dimensional geomechanical model of the same area was constructed in the 3DEC software to calculate the state of energy in the system with the progress of mining along the entire length of each panel. The variation in the energy content of the model was monitored, and zones with potentially damaging slip-type events along bedding planes followed by compressive-type events in the sandstone roof are the mechanism for large seismic events in the studied mine. The locations of anomalous events corresponded to the regions where both compression-type SPI (C-SPI) and slip-type SPI (S-SPI) were elevated. The modeling results were compared with the recorded seismic events to evaluate the model performance in forecasting the seismic potentials. The model was able to forecast 100% of regions with elevated and moderate seismic potential and 89% of regions with low seismic potential. This shows the applicability of energy balance calculations for forecasting the approximate location and timing of destructive seismic events in advance of mining.

Jun 25, 2024

By Florence Ntsiful, Eric Stemn

Exposure to whole-body vibration has been recognised as an occupational hazard in the mining industry, especially in the operations of earthmoving equipment. Managing whole-body vibration exposures requires periodic measurement of exposure levels to identify priority areas for implementing controls. However, due to different approaches to collecting exposure values, significant variabilities lie in the results. This systematic review is the first attempt to analyse whole-body assessment methods in the mining industry. The aim was to identify how whole-body vibration has been assessed, including the sources of variabilities to improve future research. The PRISMA methodology was adopted for the review and a total of 152 peer-reviewed journal articles were identified. However, only 24 were included in the review, following the application of some inclusion criteria. Descriptive and thematic analyses were performed on the 24 selected articles. Results indicate that whole-body vibration has been assessed as a function of either equipment characteristics, activity undertaken, operator characteristics, measurement approach or the assessment standards. Due to the multifactorial and dynamic nature of wholebody vibration exposures, the variabilities in results are due to the interrelationships between the risk factors of whole-body vibration and the differences in the sample sizes. To identify the sources of variabilities, a comprehensive assessment of all the risk factors, including equipment characteristics, road conditions, operator characteristics, and activity undertaken, is highly warranted. Finally, research gaps and directions for future research have also been discussed.

Dec 21, 2022

By R. L. Morse

The thermodynamic program is similar to previous mine ventilation programs but has been expanded to consider the compressibility of air. The thermodynamic program does consider: 1) air density variations, 2) humidity changes, 3) intake, exhaust, and underground fans, 4) heat transfer between rock and air, 5) refrigeration of heating plants, both surface and underground, and 6) heat generated by equipment, both diesel and electric. 110st of the compressibility factors are handled in the branch calculations. The field survey necessary to supply-data for this program is quite similar to the basic base and leap-frog pair of stations method used with most incompressible mine ventilation programs. The thermodynamic program is a complete package of ventilation network analysis which can provide mine management with good operational control and planning of mine ventilation systems.

Jan 1, 1977

By S. Yerel

Block cutter machines have been extensively used in natural stone industry, which is a sub-section of mining industry. In this study, the costs occurring in plate losses cut from Bilecik beige marble with a circular saw block cutter machine have been predicted using Statistical Process Control (SPC) techniques. One of SPC techniques is Shewhart control charts such as mean control chart. These charts have been efficiently at determining the plate losses. The costs occurring in plate losses have been calculated by using the result of Shewhart control chart. Finally, this study presents the necessity and usefulness of SPC techniques in assessment of natural stone industry.

Jan 1, 2010

By D. E. Cameron

The Cannon mine, located in north-central Washington is mining gold hosted in silicified Eocene-age arkosic sediments arrayed along a regional strike-slip fault system. Branches of the Eagle Creek fault have broken the Chumstick Formation into blocks and wedges, and have caused intense deformation of stratigraphy in the mine. Mineralization at the Cannon mine (B-Reef) and O-Reef (L-O mine) is a bulk silicification with high grade cross-cutting veins containing principally electrum, silver sulfosalts and pyrite in a gangue of quartz, adularia and calcite. Orebodies have very irregular shapes, but tend to follow stratigraphy and high-angle pre-mineral fault breccias and splays developed adjacent to the major faults. Both B-Reef and O-Reef occur at significant bends in the regional trend of major fault strands. Mean gold grades decrease upward from near sea level to the 300 m elevation at the Cannon mine. A new discovery, the A-Reef is hosted by a moderately dipping structure which is at a low angle to bedding. Fluid inclusion studies of B-Reef ore zones indicate dilute ore-bearing fluids boiled at temperatures between 185 and 2850 C at a depth of 1 km. Many ore zones are bounded by sheared mudstone and claystone and a much broader halo of argillic alteration comprising illite, smectite and sericite. Trace and major element analysis by ICP-ES for 33 elements, LECO for S, Hg by CVAA and gold by AA-FA shows dispersion patterns hundreds of meters outward from the known orebodies in the Cannon mine. Geometric mean comparisons, hierarchical R-mode cluster analysis and single element spatial plots show that Hg, As, Sb, S and K/Al compose a suite of elements which are significantly dispersed away from, and increase toward mineralization. Ba, Ca, Na, Mn, V and Zr decrease toward mineralization. The suite is more selective than gold with respect to known mineralization within the exploration area.

Jan 1, 1992

By R. L. Wiegel

Some of the mineral deposits that are being processed today, and especially those expected to be processed in the future, have relatively low compositions of the valuable mineral. With these low-grade ores, it is necessary to be able to design processes that are sufficiently low-cost to permit exploitation. One approach to minimizing the capital and operating costs for these processes is to use the capabilities of computer process simulation in the design phase of development, to make important technical and economic decisions regarding the evaluation of alternative process flow schemes, the selection of equipment and the choice of operating conditions. There are mathematical simulation models for most mineral processing operations, including several each for size reduction, size classification and mineral separations. To be able to tie these individual operating models together in an integrated mineral process simulation, however, it is important, in fact in some cases essential, that there be a model which describes how the mineral system responds to size reduction in making the liberated valuable and waste mineral particles available for concentration or rejection operations and the locked particles available for possible recirculation. This, then, is the role played by the mineral liberation model, showing the relationship between particle size, quantity and composition throughout the process.

Jan 1, 2011

St. Peter sandstone is an arenaceous sheet that covers large area in North America. The interest for St. Peter sandstone has been increasing due to the upward trend for hydrofracturing and the consequent need for fracking sand. This material is possesses very unique mechanical properties. On the one hand, it is brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, it is friable, possessing extremely low, and in most cases zero cohesion. The underground mines that are working under this condition are lacking the ground control techniques for this particular mining environment. The geotechnical properties of the St. Peter sandstone were examined using uniaxial test, triaxial test, porosity test, flexural strength test. This paper aims to investigate the effect of microstructure on strength properties, utilizing microscopic studies, index test (porosity, size distribution).

Feb 23, 2014

By Dipl. -Ing. Mertens

Gentlemen: I am pleased and regard it as a priviledge to give you a report on rapid roadheading with heading machines in the coal mining industry of Western Germany. Importance of Heading Operations in the West German Coal Mining Industry Every year about 770 km of headings are driven In the seams of the West German coal mines, most of them gate roads, the rest rise headings, to open new faces. In thick seams the heading operations are carried out entirely in the coal, in thin seams the country rock has to be ripped. The total length of 770 km corresponds to a rock volume of roughly 9.5 million m3; this figure underlines the importance of the heading operations in the coal mining industry of our country.

Jan 1, 1970