Search Documents

By B. W. Lawrence

Shaft alignment requirements are consistently met using conventional shaft sinking methods. Little attention has been given to achieving similar alignment accuracies using rotary drilled shaft methods. Alignment of these shafts is difficult to control and guarantee. Bare shafts and shafts that use drum hoisting systems can accept some deviation. However, combining drilled shafts with Koepe hoist installations presents new accuracy requirements for drilled shafts. This paper describes the importance of verticality with practical examples, and discusses various methods of measuring verticality and their respective limitations.

Jan 1, 1989

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By W. G. Pariseau

"The Crandall Canyon Mine (CCM) is located in the Wasatch coal field in central Utah. Extensive longwall mining at CCM preceded a decision to recover coal left in barrier pillars on each side of a set of main entries extending far into the mine. During mining in March 2007, a major bump occurred that led to cessation of mining in the barrier pillar on the north side of the mains and to the start of mining in the south barrier pillar. Subsequent loss of ground control in August 2007, through coal pillar bursts had tragic consequences with loss of six miners and shortly afterward three rescue team members. A U.S. Mine Safety and Health Administration (MSHA)report describes the events in detail (MSHA, 2008).An important lesson to be learned from CCM is the need to select a computer program suitable for pillar design. Computer programs are engineering tools and selecting the right tool for the job is essential. In this regard, minimum program requirements include capability for computing stress distribution within a pillar and adjacent roof and floor strata. The reason is simple: strength of rock is stress dependent; both vary from point to point in pillars and adjacent strata. Preferably, one should follow the evolution of stress as the mining plan is executed from start to finish to assure safety or to warn of a potentially hazardous situation developing as mining progresses.The approach to the problem posed by barrier pillar mining at CCM is conventional in the sense of applying well known finite element modeling techniques to analysis of a proposed mining plan. The engineering purpose is to evaluate the mining plan with respect to ground control questions including roof, floor and pillar safety. Results of previous two-dimensional finite element analysis indicated pillar safety was by no means assured (MSHA, 2008; Pariseau, 2008; Pariseau, 2011). Geometry of barrier pillar mining is limited in two dimensions for example, crosscuts are not seen in vertical cross sections. While three-dimensional analyses are preferred, even moderately sized regions often lead to very large problem sizes that exceed computer capabilities. However, a recent development in finite element modeling of tabular deposits allows for whole mine analysis in three dimensions. This technique involves a dual node - dual mesh concept. Both have been used separately in much earlier work, but are only now used in combination. It is possible to have an estimation of subsidence at a kilometer scale and details of stress, strain and displacement about barrier pillars, main entries and pillars, and so on at a meter scale (Pariseau, 2014). No compromise involving empirical formulas or similar guess work is required. Indeed, all calculations are based on first principles: physical laws, kinematics, and material laws. Effects of joints and in situ variability or uncertainty in strata properties, elastic moduli and strengths, may be included for greater realism. An important objective of the present study is to assess the role of three-dimensional pillar geometry in arriving at conclusions regarding barrier pillar mining versus two-dimensional results."

Jan 1, 2014

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a significant quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives, the authors have considered original equipment manufacturer (OEM) haul trucks, which are commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application and efficiently manage energy consumption.

Jan 1, 2010

By L. L. Probert

A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive x-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of particles. This paper will focus on the results for respirable quartz particles that occur in underground coal mines across the U.S. The relationship between the amount of surface-available quartz and coal seam rank is well established for Pennsylvania

Jan 1, 1994

By William M. Gray

[The products of mites hive historically beet a very large and important segment of total shipment transported by American Railroads. Much as the Mining transportation Executives right have wished for coal and other mineral deposits to be found along navigable rivers, where railroads have for years been competing with the very aggressive Army Corps of Engineers and the inland waterway operators, the mineable reserves are more often that not located in the arid west far from these "free" waterways. The rivers cannot go to the mines but the railroads could, did, and continue to invest it new lines to reach new mines. The mining industry and the railroad industry have good reason to rely upon each other. The former Northern Pacific Railway, the Great Northern Railway, the Chicago, Burlington and Quincy Railroad and the Spokane, Portland and Seattle Railway merged in 1970 to form the Burlington Northern Railroad, with Lou Menk as its first President. As unofficial spokesman for the industry, be had, for years, conducted a tireless effort to educate shippers, lawmakers and the general public of the single most critical problem confronting the railroad industry, the strangle bold of government regulator.]

Jan 1, 1985

The Cadia Mine is located 25kms South West of Orange in the central west of New South Wales (NSW), Australia (Figure 1). Orange is a major regional centre with a population of 35,000 people. Cadia has a history of mining and exploration dating back to 1851 and shortly after the first Australian gold rush at Ophir, north of Orange. Newcrest Mining commenced an exploration program at Cadia Hill in 1992. This identified a substantial zone of copper and gold mineralization. Subsequent resource definition drilling defined an orebody with a mineable reserve of 200 million tonnes of ore with an average gold grade of 0.74g/t and 0.17\ copper. A full feasibility study commenced in 1994, approvals to proceed with development were granted in September 1996 and the processing plant was commissioned in July 1998. The project came in on budget at A$440 million and on time, 24 months from design to construction. The estimated operating cost at the time of commissioning was A$8.85/t of mill feed.

Jan 1, 1999

By C. F. Johnson

Nearly all of the sulphur produced in the world today is converted to sulphuric acid and 49 % is used in the manufacture of fertilizers. In the last few years we have seen the beginning of another chapter in the volatile history of sulphur as the severe shortage of 1963:-67 has been transformed into present-day surplus. Prospects for further aggravation of this situation in the years ahead seem assured. In 1970, western world production showed a rate of increase of 4 -5%, which 1S somewhat less than that of 8% for the period 1963-1967. The rate of growth of consumption dropped considerably in 1968 when the demands of the fertilizer industry fell. During the same period of time, wide-spread demands have been set in motion for a clean environment which indicates that a fundamental change in sulphur supply, demand, and even sources, is likely to result from this upheaval. The sale of sulphur by Poland to the western world has increased and for 1970 was estimated at over one million metric tons. In the next few years, increase in Canadian sulphur supply will stern from two sources;

Jan 1, 1972

Solvent extraction-electro- winning appears to be one of the most important processes for the future in the North American copper industry and for this reason both the SX and EW steps are furtive areas for development. This paper has the objective of reviewing the present state of the electrowinning technology. It discusses some recent equipment developments and concludes by discussing the direction the technology will likely go fn the next decade.

Jan 1, 1985

By Fitzhugh T. Lee

Results from the first part of a two-part investigation of the stability of highwalls in open-pit coal mines in the Paleocene Fort Union Formation of the western Powder River Basin of Wyoming and Montana indicate that these highwalls are subject to time-dependent deformation. Field investigations and laboratory physical properties tests of coal and overburden rocks suggest that several factors influence highwall stability. Some of these factors are rebound of overconsolidated rocks, desiccation, water, orientation and spacing of fractures, and strength and deformation properties. Factors of safety for a typical highwall in the study area (calculated by the finite element method) may be less than 1.0 when open fractures are present and the highwall has degraded. Although it is concluded that most open-pit highwalls in the Fort Union Formation within the study area have adequate short-term stability, these highwalls do deteriorate and become progressively less stable. Because of this, postmining failures are common and stability conditions could become critical if mining were delayed and then resumed after a period of several months. The second part of the investigation will utilize field measurements of rock-mass properties and instrumentation of actively mined highwalls to obtain data for comparison with the results of the initial investigation. Because the height of highwalls will increase as the more shallow coal is exhausted, these data will also be used to predict the behavior of slopes higher than those presently found in the western Powder River Basin.

Jan 1, 1977

By M. Canty

An innovative biological treatment system designed to detoxify cyanide and nitrate and immobilize metals from cyanide leach operations is described. A pilot-plant demonstration was conducted to detoxify cyanide and immobilize several metals from a process stream at the McCoy/Cove Mine. Testing was performed under the EPA's Mine Waste Technology and Superfund Innovative Technology Evaluation Demonstration Programs. This technology was successful in detoxifying cyanide and effective in removing metals. The pH was consistently neutralized and nitrates were successfully removed. Results show that biological treatment can offer an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1999

By J. B. Davis

Isotope analyses distinguish biogenic sulfur ores from non-biogenic ores, but do not distinguish bioepigenetic from biosyngenetic ores. Sulfur deposits of salt dome caprocks and of bedded Permian evaporites of west Texas, however, are clearly bioepigenetic. Anhydrite, introduced by salt diapirs into geologically younger sediments, is converted biogenically to sulfur and calcite in the presence of petroleum; for example, in Challenger Knoll, a salt dome at a water depth of 3600 m in the Gulf of Mexico. Bedded evaporites of west Texas in association with petroleum show an obvious epigenetic replacement of the anhydrite layers by biogenic sulfur and calcite

Jan 1, 1978

By S. A. Rholl

This paper describes the Bureau of Mines experimental test program which evaluated the effectiveness of using high explosives to enhance orebody permeability. To determine the effect of stress on the fracture network generated by blasting, fifteen single-hole laboratory tests in granite blocks up to .067 m3 (2.4 ft3) in size were blasted using .12 to .20m (4.8 to 8.0 in) of 1.6xl0-3-, 3.2xl0-3-, or 6.5xl0-3-kg (25-, 50-, or 100-grain) detonating cord. In situ stresses were simulated using polyaxial load cells to apply uniform stresses of 1.72xl06 to 1.76xl07 Pa (250 to 2550 psi). All of the blocks were sawed to expose the blast-induced fracture patterns for analysis.

Jan 1, 1991

By S. A. Smith-Hamm, E. A. Sarver, A. S. Cox

Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and inductively coupled plasma-mass spectroscopy (ICP-MS) was used to determine how leaching conditions affected the release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that for certain spoil materials, the SC in the leach column effluent was effectively reduced when the spoil was first leached with acidic rainwater followed by ambient rainwater, as opposed to leaching with ambient rainwater alone. This suggests that accelerated leaching might aid in the long-term stabilization of some materials.

Jan 1, 2015

By David L. Giles

The Lime Creek* ore body in northwestern British Columbia is one of the few commercial primary stockwork-type molybdenite deposits in North America. Others include the Climax, Urad-Henderson, Questa, and Endako ore bodies. They are mined on a low grade-high tonnage basis, and are open pit operations except for Climax and Urad-Henderson. Much recent geochemical research on both porphyry copper and stockwork MoS2 deposits has been concerned with dating of micas related to the mineralization and associated igneous rocks. The results appear to show that mineralization and the predominant magmatic events of the deposit are indistinguishable in age (1-5), except where dating has been in sufficient detail to resolve the analytical overlap (6). At Lime Creek, geologic information shows that the Main granodiorite, the major intrusive and dominant host rock for MoS2 mineralization, was emplaced and had solidified sometime prior to the introduction of MoS2. The first MoS2 episode is intimately related to localized bodies of kalialaskite which clearly intrude the older stock. K-Ar dating was undertaken to clarify the age relations between Lime Creek plutonism and the apparently younger hydrothermal event that began with kalialaskite.

Jan 1, 1975

By M. L. Free

Acid consumption in copper heap leaching is determined by the minerals present in the ore. Gangue minerals such as biotite and chlorite consume acid together with copper-bearing minerals such as chrysocolla and malachite. Acid consumption is affected by the rate of acid application and the particle size. Some gangue minerals undergo alterations and cause precipitate formation during acid leaching. Other minerals form due to precipitation as dissolved ion concentrations from a variety of mineral sources combine to exceed saturation levels. Copper recovery is related to all of these events. This study presents information on acid consumption of various gangue minerals as well as data for copper recovery from an associated copper ore.

Jan 1, 2010

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the disasters occurring in underground coal mines. As a typical case, the spontaneous combustion of broken coal left in the longwall gobs often happen which could greatly interrupt the normal mining production. Such concealed thermal event is featured as rapid development and difficulty in locating “hot” spots. If such spontaneous combustion fails to be timely prevented and controlled, a large amount of toxic gases (mainly CO) and smoke could flow and diffuse in the underground working sections, which could present safety hazards for coal miners. In this paper, based on an coal spontaneous combustion event happened in a Chinese gassy mine, the fire ratios derived from the gas composition data obtained through the tube bundle mine atmospheric monitoring system are used in determining the fire status. A comprehensive and collaborative fire extinguishing effort including inert gas injection, underground pressure balance, and sealing enhancement are made to control the fire progress. Simultaneously, the effects of such works to control the spontaneous combustion event have also been quantified using the fire ratios to justify again. Finally, the danger of coal spontaneous combustion in gob is eliminated, and the longwall panel is successfully re-opened for normal production.

May 6, 2021

A digital computer program has been developed to mathematically simulate the effect of limited changes in feed rate on the grinding circuit of an operating mill. The data on which the program is based was supplied by the staff of the mill in question. Samples taken around the complete grinding circuit were analyzed for solids content and particle size distribution for two feed rates. Matrix models were used to represent the grinding units: rod mill and pebble mills. Parameters for these models were computed using a method developed by Mular(l). Classifier parameters were computed by the Powell search method(2) for the Plitt model (3) . The simulation program, which permits the computing of the size distributions in the circuit resulting from the changes in feed rate between the two measured values, assumes that a linear relationship exists between the corresponding parameter coefficients. The program uses an iteration method to bring the simulated grinding circuit to a steady-state material balance for any specified' feed rate between those measured. The program is, in addition, extremely fast and economic in computing time. The results show that the simulations are not everywhere consistent with practice. For example, higher feed rates on simulation predict finer products. These errors are shown to be attributable to anomalies in data gathering techniques. An improved sampling procedure for grinding-circuit data gathering is suggested for future simulations of this type. It is concluded that the

Jan 1, 1971

By R. Wisniewski

Every underground coal mine in the United States must deploy and operate a wireless communication and tracking system. This paper addresses the reliability and availability of an installed tracking system and the communications infrastructure that supports it. A particular interest is the requirements for the systems to operate continuously without failure after a mine disaster for 96 hours, and the requirements in the MINER Act for the tracking systems to be ?calculated to be serviceable? and the communications systems ?redundancy?. These requirements imply a certain reliability and availability. This paper describes a quantitative way to assess these systems requirements, using the tools that are available and commonly used by the Reliability, Maintainability, & Availability community.

Feb 23, 2014