Search Documents

By Abegail Endraca, Allan Sebastian, Andrew Raine, Allan Patdu

The project involves the construction of a new aqueduct tunnel by an Earth Pressure Balance TBM tunnel for the Novaliches-Balara Aqueduct No 4 (NBAQ4) project in Metro Manila. It comprises a 7.3 km long and 3.1 m internal diameter tunnel that can deliver up to 1,000 MLD of raw water and the tunnel passes under urban residential and urban populated areas adjacent to and along Commonwealth Avenue. A new reservoir intake structure was constructed in the La Mesa reservoir by a cofferdam and the TBM breakthrough connected the reservoir to the outlet surge shaft structure and the downstream pipe network system connecting to the Balara Water Treatment Plant. The TBM incorporated a double articulated head configuration to allow tight 80 m radius curves to navigate some of the difficult alignment considerations. The alignment passed very close to some existing foundations for MRT7 and needed to clear several tight curves to remain within government land ownership. The project excavated through the local Guadalupe weak rock formations and there was minimal ground movements observed as a result of the work.

Jun 13, 2023

By Steven K. Ruggieri

Increased coal production on longwalls has brought with it higher levels of dust generation. Most U.S. longwall mining operators have difficulty complying with Federal dust standards, which are stricter than European standards. Longwall operators faced with a longwall that is "out of compliance" have implemented a variety of practices designed to reduce dust levels. Mining conditions and other important variables, however, can cause fluctuations in dust levels that may overshadow the performance of a new dust control technique. This can result in the continued use of an ineffective technique or lead to the abandonment of an effective dust control technique. No single technique can keep a longwall in compliance. Maintaining compliance requires a fundamental approach to dust control -- proper application and continued use of effective dust control techniques.

Jan 1, 1983

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

Terminology. The term potash originated in "pot ashes" produced by burning wood to ashes in iron pots and then leaching out the soluble salts, chiefly potassium carbonate, from the residue. In modern usage potash is a generic term for various potassium salts used in agriculture and industry. More specifically, it denotes the oxide of potassium, K2O, and the content of potassium in ores and products is stated as weight percent of K2O present. Its salts are commonly referred to as muriate of potash, sulfate of potash, etc. The presence of an adequate supply of available potassium in the soil promotes the health and improves the quality of the plant. insures greater efficiency in photosynthesis, increases resistance to certain diseases, offsets the effect of an oversupply of nitrogen, and helps the plant to utilize soil moisture more advantageously. ("Soils and Men," U.S. Dept. of Agriculture Yearbook 1938.) Occurrence. Potassium ranks seventh among the elements in abundance. It is estimated to constitute some 2.6% of the lithosphere and is found in soluble forms in the oceans, lakes, rivers, and subsurface waters. It is also an important constituent of plant and animal life. Commercially significant accumulations of potassium salts occur in underground deposits formed in past geologic times by evaporation of ancient bodies of saltwater, inland drainage basins, and shallow sea lagoons. The potash content of such waters was the end result of weathering and leaching of insoluble potash-bearing aluminosilicates, such as feldspars, micas, leucitcs, and others. The concentrations of potassium salts in the natural brines of some lakes in the arid and semiarid regions of the continents are also important as sources of potash; the brines of the Dead Sea in Asia Minor, the Great Salt Lake in Utah, and Searles Lake in California typify such concentrations. Every continent has major potash deposits as listed in Table 1 adopted from Cawley.1

Jan 1, 1985

By H. Wesley Peirce

Arizona embraces portions of two major western-U.S. physiographic-geologic provinces and a smaller, local one. These exert fundamental control over the geologic framework and associated earth-material resources and potential. The Mogollon Rim diagonally crosses the State and separates the Colorado Plateau Province to the northeast from the Transition Zone and Basin and Range Province to the southwest. More than 90 percent of the population, production of nonfuel minerals, agricultural land, and water resources are in the Basin and Range part of the State. In 1981 Arizona was ranked number one in the Nation with respect to the value ($2.56 billion) of nonfuel-mineral production. About 8.2 percent of this amount ($212.9 million) can be attributed to nonmetallic (industrial) materials. Although a diversity of nonmetallic substances is produced and some are exported, the bulk is utilized within the State and is directly related to market growth. Since 1950 there has been a fourfold increase in Arizona's population, a concomitant twelvefold jump in sand-gravel production (tons), and a twentyfold increase in "stone" production. New industries developed during this time include cement, salt (and storage of liquid petroleum gas products in solution cavities in salt), zeolite, hydrofrac sand, vitrified clay pipe, crushed marble products (teed additive, pool sand, roofing granules, etc.), and "rock" wool. Most of these newer industries serve out-of-State as well as in-State markets. In 1981 at least 225 industrial mineral or rock deposits were being worked to produce about 10 tons of material per Arizona resident per year. In 1980 the relative values of basic industrial minerals produced in the State, by major group, were cement and lime (51.6 percent); gravel (26.5 percent); sand (11.8 percent); stone (4.6 percent); and others (5.5 percent). Detailed knowledge of the nonmetallic rock-and-mineral content of most Arizona ranges and basins is lacking. Exploration opportunities in this sun-belt growth region appear encouraging.

Jan 1, 1987

By V. T. McLemore

The Wind Mountain (WM) nepheline syenite deposit is part of the alkalic complex in the Cornudas Mountains, which ranges in age from 34.6 ± 1.5 Ma to 36.8 ± 0.6 Ma. The WM deposit consists of a complex, zoned pluton that ranges from syenite porphyry to nepheline syenite porphyry. The WM deposit has potential use for ceramics and dark-colored beverage containers and consists of nepheline, k-feldspar, albite, and varying amounts of other minerals. Analcime also is present locally but must be avoided because it is unsuitable for ceramic and glass. Chemically the deposit consists of 56-63 % SiO2 17-21 % Al2O3 and 4.0-5 % Fe2O3. Although initially iron is high, when the crushed rock is passed through a specialized magnetic separator, the iron content drops to below commercial maximum standards of less than 0.5% Fe2O3. The WM deposit is currently under exploration and testing to determine marketability.

Jan 1, 1994

By M. R. Yalamanchili

Recently, noequilbrium electrokinetic measurements using laser-Doppler electrophoresis were reported by Miller et al. (1992) for alkali halides and the sign of their surface charge thus determined. These results are generally as expected from simplified lattice ion hydration theory with KCI, under normal circumstances, being the most significant exception. In this regard, lattice defects (F centers and oxygen imperfections) have been found to influence the surface charge of KCI and its electrophoretic mobility. In particular, the presence of oxygen defect states in the crystal lattice has been found to be responsible for KCI's unexpected behavior. The concentration of oxygen defect states in KCI, as characterized by UV/Vis absorption, was varied in order to study their influence on the electrokinetic behavior and subsequently on the flotation response of KCl. At low oxygen contents « 60 ppm) KCI is positively charged as expected from lattice ion hydration theory. However, typically, KCI contains substantial oxygen (>300 ppm) sufficient to impart a negative surface charge which accounts for the selective flotation of KCI from NaCl by hetero-coagulation with oppositely charged alkyl amine hydrochloride collector colloids.

Jan 1, 1994

By Walter E. Dean

Deep-sea manganese nodules are considered to be potential ores of manganese, nickel, cobalt, and copper. Considerable time, effort, and funds have been applied to the study of Se distribution of nodules on the sea floor and the location of economically important areas, but little effort has been spent in understanding the origin of nodules. Most theories that have been proposed to explain the origin of manganese nodules have been based on inorganic physicochemical processes. It is not by coincidence, however, that the area considered to be most economically feasible is in the zone of high biological productivity in the eastern equatorial Pacific Ocean and underlain by siliceous biogenic sediment. The genesis of manganese nodules and the concentration of many trace elements are intimately associated with biological processes.

Jan 1, 1982

By M. J. Virnig

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-1 and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

"During his presentation at the 2016 George A. Fox Conference about the history of public-private-partnerships (PPP) in the tunneling and underground construction industries in New York, Vincent Tirolo, Jr., told a story about how, as a young engineer in the late 1960s, he and others pooled money to purchase a calculator for $75 that had the ability to perform sine and cosine functions. That was a big deal in those days and would make their job much easier. Oh how far things have come. Tunnel and underground construction engineers can now virtually map out and plan entire projects before the first shovel ever breaks ground. And the machines that are used to build the tunnels have advanced in ways that could not have been imagined 50 years ago.The calculator is just one example of innovation in the industry and on Jan. 26, more than 400 industry professionals attended the George A. Fox Conference at the Graduate Center of New York (CUNY) to learn more about the next innovations, new tunneling technologies and what the future might hold for the industry. The conference included sessions on contracting models, rescue and fire life safety and new technological developments as well as an international project spotlight presentation from Nasri Munfah about the Eurasia Tunnel, connecting the European and Asian sides of Istanbul, Turkey.The project, also known as the Istanbul Strait Road Tube Crossing project, was named the 2015 Major Tunneling Project of the Year by the International Tunneling and Underground Space Association.The tunnel boring work for the 3,344-m (11,000 ft) long tunnel under the Istanbul Bosphorus Strait was completed in August, heralding a new era in tunneling.Tunnel boring work was launched in April 2014 with a ceremony with then Prime Minister Recep Tayyip Erdogan in attendance. The work was completed on Aug. 22, 2015 with Prime Minister Ahmet Davutoglu participating in the ceremony."

Apr 1, 2016

By Carl Erickson

The term shortwall mining is somewhat of a mis¬nomer. It may infer a longwall mining system, but of much shorter face length. Actually, continuous pillar mining is a more descriptive term. Coal is mined using a continuous miner as would be done in pillar extrac¬tion, but with the addition of roof supports to control the caving. Face length on such a system typically is 46 to 61 m (150 to 200 ft). The coal is cut in front of the roof supports in the same direction as with a long¬wall shearing machine or plow, but it is mined with a continuous miner and shuttle cars of the same type as used in continuous mining. ROOF SUPPORTS Roof supports for shortwall mining must be con¬siderably larger than those used for longwall mining because of the additional roof to be supported by the wider 2.6- to 3.4-m (81/2- to 11-ft) cut of the continuous miner. Capacities of shortwall chocks in current use vary from about 454 to 726 t (500 to 800 st). The higher capacity as compared to longwall roof supports is needed primarily because of (1) the greater support length, hence more roof weight, and (2) the presence of draw slate in the eastern coal seams, where shortwall is being used. The most popular shortwall support currently used is the four-leg 590 t (650 st) model. This support is shown in Fig. 1. The price of this support is approxi¬mately $25,000 each. As shown in Fig. 1, the shortwall chock incorporates an unusually long forward bar that has an additional hydraulically operated extension bar to provide face support for the wide miner cut. METHOD OF OPERATION Mining Sequence In shortwall mining, two or three (depending upon the chock design) move up cycles of the chock are needed because of the miner cut width. Fig. 2 depicts the five steps required to complete the move of chock and spill plate using a miner that takes a 3.3-m (10-ft,

Jan 1, 1982

By Atta Ur Rehman, Kwame Awuah-Offei

This paper examines the effect of bucket geometry (cutting-blade profile, floor profile and blade thickness), speed, motor power output and muckpile particle sizes on bucket penetration and draft for rubber tire loaders. The work uses a 1:16 scale model of a load-haul-dump (LHD) in full-factorial experiments to examine the effect of the variables on penetration and maximum draft. The results show that speed and motor output are positively correlated with penetration and draft, and muckpile particle size is positively correlated with penetration and negatively correlated with draft (p < 0.0014).

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By Gordon Clark, Basar Arioglu, Nasri Munfah, Sanja Zlatanic, Tolga Togan

"The 13.2 m (43 ft) external diameter, double deck Istanbul Strait Road Tube Crossing is one of the most challenging underwater tunnel projects in the world. Subjected to 11 bars of hydrostatic pressure, variable geology, and being in a very active seismic area, the execution of the project required innovative solutions, sophisticated construction techniques and prudent risk management approach. The 5 km (3.1 mile) tunnel consists of a 3.4-km (2.2-mile) tunnel boring machine- (TBM) bored tunnel, 1 km (0.62 mile) twin NATM tunnels and cut-and-cover sections. The project is being delivered in a build-operate-transfer (BOT) contract in a public-private partnership. The technical challenges, coupled with financial and commercial risks required the implementation of sophisticated risk management tactics including the provision of independent design verification. The project was opened to traffic on December 20, 2016, four months ahead of schedule.. This article presents the technical challenges of the project from the design, construction, and risk management aspects..Project backgroundThe $1.245 billion Istanbul Strait Road Tunnel Crossing project, dubbed the Eurasia Tunnel, is one of several major infrastructure projects being implemented in the Republic of Turkey in a public-private partnership approach. The project provides a direct and easy connection between the Anatolian (Asian) side of Istanbul and the heart of its historical district on the European side across the Bosphorus Strait which connects the Black Sea with the Sea of Marmara. The project improves connections to a wide network of motorways on both sides, increase capacity across the Bosphorus by 100,000 vehicles a day, reduces congestion and saves motorists an average of 45 minutes of commuting time in each direction bringing significant economic benefits to the city and the region. It eases traffic across the strait, reduces congestion, decreases pollutants and emission while maintaining Bosphorus. It is the most complex part of the project with the greatest challenges and risks. Part 2 is 5.4 km (3.6 miles) long consisting of 3.4 km (2.2 miles) of 13.2 m ( 43.3 ft) external diameter TBM bored tunnel under the Bosphorus Strait, 1-km (0.62-miles) of twin NATM tunnels on the Asian side, cut-and-cover transition boxes in the Asian and the European sides and depressed approaches on both sides. In addition, this segment includes the toll plazas, ventilation buildings, and the tunnel control and maintenance facilities."

Mar 1, 2017

By Eugene A. Lang

Mr. Chairman, ladies and gentlemen. As a member of the uranium and coal producing community, I am pleased to participate in a session dedicated to a look at these and other mineral markets.(title slide) before sharing some of my thoughts with you, let me tell you a little bit about rocky mountain energy company. It was established as a subsidiary of union pacific corporation in 1971 with responsibility for coal, uranium, and industrial minerals. We participate in four coal mining operations and a uranium mine and mill all in Wyoming, and an aggregate and an abrasive operation in Utah.

Jan 1, 1984

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By Paul H. Johnson

Heap leaching is a simple means of recovering copper from oxide and oxide-sulfide ores. Although this method requires relatively low capital investment, it suffers from low copper recoveries and relatively high acid consumption. The objectives of this study were (1) to determine what factors influence these shortcomings, and (2) to establish a basis of correlation. between laboratory and field testing. The principal methods of leaching copper ores at the present time are heap, dump, in-place, and vat. A number of references are presented in the bibliography on the theoretical and practical aspects of these methods. In the heap-leaching method, crushed or uncrushed oxidized copper ore is placed on a prepared drainage pad. Acid leach solutions are dis¬tributed over the top of the heap, caused to percolate downward through the ore bed by gravity, and are drained from its base. The leach duration is generally a matter of a few months. Dump leaching is used to recover copper from very low-grade oxide-sulfide pit-waste materials. Here again, leach solutions are, percolated downward through a heap. However, in this method, little or no acid is added to the leach liquors, prepared drainage pads are not used and the leaching cycle is generally measured in terms of several years. Leaching agents are usually autogenously generated by the breakdown of sulfide minerals within the dump.

Jan 1, 1970

By James N. Orlich

Meridian Gold Company&apos;s Royal Mt. King mine (RMK), a subsidiary of FMC Gold Company, is located approximately 40 miles east of Stockton, California on the western edge of the historic mother lode belt. Gold ore at RMK is associated with a series of northwest trending fault zones hosted in either meta-volcanic or meta-sedimentary rock types commonly referred to as greenstone sulfide and carbonaceous phyllite. Mineralogy studies show gold in both ore types to occur primarily as electrum in the form of 1 -20 um inclusions in pyrite with varying amounts of free milling gold. In carbonaceous ores, gold was not found to be closely associated with carbon. At the start of the current mining operation, three major ore resources were identified. North Pit and Gold Knoll pits were the major greenstone reserves while Skyrocket Pit contained over 60% of the total reserves as carbonaceous ore. Since North Pit and Gold Knoll were to be the first areas mined, the mill began operation in February 1989 with a flowsheet designed for greenstone ores with a carbonaceous expansion anticipated after depletion of the greenstone reserves.

Jan 1, 1992

By K. Louk, E. Gilliland, N. Ripepi, M. Karmis

"Carbon dioxide (CO2) injection in deep unmineable coal seams can enhance coalbed methane (CBM) recovery as well as effectively and permanently store the CO2. Enhanced coalbed methane (ECBM) recovery and CO2 storage capacity can be improved by altering injection parameters including the injection well locations, number of injection wells, and the time and rate of the injection. A sensitivity study was performed with sixteen different injection scenarios on a coalbed methane field in Buchanan County, Virginia to understand the influence of the injection parameters on methane production, CO2 storage and the extent of the CO2 plume. History matching was done for the gas and water production period prior to injection based on field data from an active US Department of Energy funded pilot project. INTRODUCTION The coal structure is a combination of the coal matrix and cleats. In a CBM reservoir, the methane (CH4) is stored in the matrix under adsorption properties, not as a free gas. During CH4 production, the reservoir pressure is reduced and gas is released from the surface of the coal, diffuses through the matrix and transmits to fractures (man-made or natural) via the cleat network. Fractures and cleats are the major parameters that influence gas flow capacity because deliverability of the CH4 to the production well is controlled by the cleat permeability. As gas production continues over time, CH4 desorbs from coal, and coal matrix volume starts to decrease. This volume decrease in the matrix opens up the cleats, matrix shrinkage, which leads to a permeability increase. Several emprical (Harpalani and Schraufnagel 1990a, 1990b; Harpalani and Chen 1995, 1997; Harpalani and Mitra 2010; Pan et al. 2010; Liu et al. 2012; Mitra et al. 2012) and analytical (Palmer 2009; Liu and Harpalani 2013) studies have reported this relationship between pressure and permeability. Those studies showed that permeability is an important parameter in CH4 production performance. Furthermore, during gas production, water is produced through the cleat system as well, therefore gas-water relative permeability must be also considered in evaluating production performance (Gash et al., 1991). In the CO2 injection scenario the opposite occurs because CO2 has a higher adsorption affinity than CH4. CO2 replaces CH4 in the matrix of the coal and increases the volume of the coal matrix, matrix swelling, and results in a permeability decrease. Harpalani and Mitra (2010) concluded in their experimental study that swelling of the coal matrix due to the CO2 injection is two to three times more than the sorption of CH4, resulting in large permeability changes during CO2 injection."

Jan 1, 2016

By James E. Lawver

The agriculture industry has made great strides during the past decade to increase agriculture yields through increased use of fertilizers. Increased use of fertilizers may prevent or at least delay mass starvation due to the alarming increase in world population. Phosphate was added to soil as a plant nutrient in the forms of calcined bones at least 2 000 years ago, (1) and man has used phosphate minerals as a source of fertilizers in one form or another for at least 100 years. During 1977 the world produced about 116 million metric tons of phosphate rock, with about 86% used for fertilizers and another 4% for animal feed supplements. More than three-fourths of the total production comes from the United States, Morocco, and the Soviet Union. From a mineral beneficiation point of view, the major sources of phosphate rock and the methods of beneficiation can be classified as follows. Marine deposits not containing appreciable carbonate minerals, marine deposits requiring a francolite carbonate mineral separation, igneous deposits not containing appreciable carbonate minerals, and igneous deposits, requiring an apatite carbonate mineral separation.

Jan 1, 1978