Search Documents

By Lee W. Abramson, Kenneth P. Akins

The authors have accumulated published data on residual soil and rock tunnels in the United States and have compared it to transit tunneling experience in Atlanta, Georgia, and tunnels in other soil and rock conditions. Two 6.1 meter (20 foot) diameter shield driven, compressed air tunnels were constructed for the Metropolitan Atlanta Rapid Transit Authority (MARTA) connecting the Five Points Station (central hub) with the Peachtree Center Station (first station on the north line). Because of the historic multi-story structures above the tunnels and the variety of subsurface conditions, a comprehensive ground monitoring and observation program was conducted. Conclusions are drawn regarding residual soil and rock ground response due to tunneling. Comparisons are made to ground response due to tunneling in other soil and rock conditions.

Jan 1, 1983

Current design guidelines for the surface catalysed oxidation of Fe(II) on Fe(OH)3 (Ochre) in passive mine water treatment systems are based largely on empirical data as the details of rates and mechanisms have not fully been revealed. Also the effects of elevated carbonate concentrations, typical of many UK minewaters, on the surface catalysed oxidation rate are unclear. In order to move away from empirical design and towards sound engineering that is based on geochemical and hydrological understanding it is necessary to quantify these reaction rates. In this study the effects of Fe(OH)3 and carbonate on the rate of Fe(II) oxidation by dissolved oxygen have been investigated with an aim to delineate the reaction mechanism. Experiments were conducted under well-controlled conditions. Preliminary results indicate that the surface catalysed reaction is an order of magnitude faster at pH ~6.4 with 200 mg/l Fe(OH)3 than the homogeneous rate and is dominated by an elevated rate of removal and oxidation of Fe(II) from the solution phase. It is also apparent that the oxidation rate of actual adsorbed Fe(II) is substantially retarded with respect to the homogeneous rate. Carbonates were not shown to affect the surface rate within the bounds of this preliminary study.

Jan 1, 2006

By Charles C. Dahl, Gordon C. Presley, Andrew E. Nevin, Bruce A. Kennedy

How does SME-AIME cope with profound changes in technology, markets - and most importantly - in employment patterns facing its membership today? This is the question that prompted the Society's Board of Directors to appoint a Long-Range Planning Commission (LRPC) (see ME, Feb. 1984, pp. 118 and 128). This is also the question addressed most particularly by the LRPC's Scope Committee. The Committee started its deliberations by asking such basic questions as "Who are we?" and "What is our business?" The Scope Committee then reviewed the findings and recommendations of other more specialized committees to develop and integrate their concepts of the Society's business for the next 10 years. The policy-making suggestions of the LRPC were reviewed and acted upon by the Board of Directors at its open meeting in Los Angeles on Feb. 26, 1984. At the Oct. 23-26, 1984 SME Fall Meeting in Denver, the Board will again review LRPC recommendations. In answer to the question "Who are we?" the Scope Committee proposed description, which was accepted by vote of the board of directors: . . A technical and professional organization that consists of individual members, namely those mining engineers, metallurgists, geologists, earth scientists, economists, managers, educators, and other professionals concerned with all facets of exploration, production, distribution, and using of mineral commodities. "These mineral commodities include all metals; industrial minerals, including construction materials and fertilizers; coal, oil shales, tar sands, and other mined fuels. Among the earth's mineral resources, only wellpumped oil and gas lie outside the Society's specific purview. "Traditionally, SME members work in the fields of engineering, technology, exploration and discovery, development, construction, mining, quarrying, beneficiation and processing, handling and transport, equipment manufacturing, sales and marketing, data processing, safety, land reclamation, environmental protection, taxation, administration, and management of these elements. "Members practice their professions in industry, in universities and research institutions, and in government. They may be operators, manufacturers, sales persons, contractors, consultants, analysts, researchers, educators, advisors, regulators, or members of supporting staffs. "The members of the Society are leaders in dedication to their crafts, in innovation, and in the pursuit of excellence. Among their numbers they count the most distinguished of engineers, applied scientists, and managers. "The Society is based in the United States, is active on a worldwide basis, and is open to nationals of any country. Certain qualifications must be met for attaining and maintaining membership." Purpose of the Society As to the question "What is our business?" the Scope Committee restated our purpose in light of current practice and the constitution of AIME and the bylaws of AIME and SME. The Board of Directors accepted the following proposed purpose of SME: "To further the professional development and well-being of its members by publishing and distributing technical writings, news, and information; by sponsoring meetings of members; by providing forums for discussions and for continuing education; and by fostering communication on the subjects within its purview. "The Society assists educa-

Jan 4, 1984

The occlusion of unliberated gold particles in silicates and sulfides in crushed/milled ore dictates the recovery that can be expected. The grade of this occluded gold in cyanide leach residues shows a consistent, general relationship to the head grade of the ore, irrespective of mineralogy or geographical location. The residue grade almost invariably increases with the head grade, but not in proportion to it. This phenomenon appears to stem from the nature of the geological events originally responsible for creating the ore deposits. A statistically-based technique for determining the true head grade-tail grade relationship from gold plant operating data is described. The effect is illustrated with results from several worldwide gold milling operations analyzed over the last 35 years.

Jan 1, 2008

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By R. W. Kobler

The pelletizing process for low grade iron ores has undergone continual changes since its inception over twenty years ago. These changes have necessitated filtration equipment changes in order to produce a product suitable for balling. With modern techniques it is now possible to produce pellets of 68% Fe from ores containing as low as 26% Fe. Low grade ores require fine grinding to liberate impurities This shift to finer grinds over the years has necessitated major changes in the filtration steps. Techniques are now available for producing suitable product from ores with Blaines as high as 3600 cm2/gram. This has been made possible by the development of high performance filters. Recent developments have reduced maintenance costs and produced higher production reliability. The paper discusses iron concentrate filtration from its beginning to present day design. It will be shown that the dewatering step prior to balling has gone through four generations of filters. Particular emphasis is placed upon hydraulic studies which have allowed today's optimum designs.

Jan 1, 1978

By C. H. Bucknam

Classical acid-base accounting using modified Sobek titration methods has resulted in interpretation of results for materials with neutralization potential (NP) less than 20 tons of CaCO3/1000 tons of material (2% CaCO3) as "uncertain" due to lack of sensitivity within that content range. Standardization of a "fizzless" acid neutralization potential (ANP) method was undertaken in the American Society for Testing and Materials (ASTM) International using two ranges of sulfuric acid additions based on reaction pH and carbonate carbon estimates rather than subjective fizz testing as well as hydrogen peroxide additions to correct for mineral acidity. The method is identified as the acid neutralization potential acidity (ANPA) titration method. During interlaboratory testing a positive bias was discovered within the "uncertain" range which was further investigated and resolved by increasing the test sample weight from one to five grams for samples needing improved accuracy in materials with ANP <2% CaCO3. Test results from the interlaboratory testing of the low range method is presented and compared with the results from the original ANPA method in the paper.

Feb 27, 2013

At present, discounted cash flow analysis is generally accepted as the preferred method of valuation of mine projects in surface coal mining. One of the major reasons for that is its ability to take into account the time effect of money over the life-of-mine. As a looking-forward method, it requires forecasts be made with regard to economic, technological, technical, geological, and environmental conditions that will prevail in the future. All forecasts are inherently uncertain as they are a function of the uncertainty of all variables of the discounted cash flows analysis. This indicates that the only alternative for modeling the uncertainty in the project evaluation is the development of adequate risk models to serve the decision-making process. The paper offers a model of project cash flows at risk in strip coal mining, which is an integrated corporate risk management solution. The model is based on a stochastic approach that provides the answer to the question about how large is the deviation between stochastic cash flows and the planned value (or that used in the budget) at each time step of the discounted cash flows analysis, that is due to the uncertainty in the model variables. A solution is worked out for the allowable range of the stochastic cash flows variation that determines the probability of achieving the planned value of a mine project. The Monte Carlo simulation technique is used to model the stochastic behavior of the project variables. A case study of an opencast coal mine project is provided to illustrate the applicability of the risk model. The results obtained provide a new understanding of the mine project risk as a component of the project discount rate.

Jan 1, 2006

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder&apos;s estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson&apos;s paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984

By D. Malhotra

The economic viability of a mining operation depends on continuous process improvements. Diagnostic testing and plant auditing are essential useful tools to improve performance and reduce operating costs. Case studies are discussed to illustrate benefits of these techniques to improve plant efficiency.

Jan 1, 2001

By S. Janisko

Studies have linked long-term inhalation of diesel exhaust with adverse health effects such as cardiovascular disease, cardiopulmonary disease, and lung cancer. Diesel exhaust levels in underground mines can approach 100 times the environmental level and are therefore monitored closely in the mining industry. Elemental carbon (EC) (a product of diesel combustion commonly referred to as ?soot?) has proven to be a good indicator of diesel exhaust levels. The current procedure for measuring EC levels involves taking personal samples from a mine worker?s breathing zone and/or stationary samples in various parts of the mine and subsequently sending these samples to a lab for analysis by NIOSH 5040 method. Unfortunately, the whole process can take up to several weeks to complete. To address the problem of waiting weeks for results, NIOSH?s Pittsburgh Research Laboratory is developing a portable device for measuring levels of elemental carbon. This optical device takes a continuous sample of air in the surrounding environment and measures the absorbance of light passing through a filter that collects diesel exhaust particulates within the instrument. This technology can provide a near real time measurement of EC with accuracy within 10% error. The ability to take near real time measurements, combined with the instrument?s portability (currently small enough to be worn on a miner?s belt), makes this device extremely useful in the mining industry.

Jan 1, 2009

By M. Mankosa, G. Taylor, G. Luttrell, J. Yasalonis

Several industrial-scale HydroFloat separators have recently been installed at Mosaic’s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale, and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The apparent benefits, theory of operation, and commissioning of the equipment are also discussed.

Jan 1, 2007

By D. Noon

Mine production crews and drill-and-blast crews may be exposed to unexpected movement of ground when working under pit slopes. Without specialist geotechnical advice and appropriate measurement systems, mine crews are faced with conducting risk assessments and relying on subsequent controls that may or may not be adequate to ensure their safety. Mine crews need an ?early warning? monitoring system to give them the confidence that they will have time to walk out of the danger zone if the pit slope begins to move. Slope stability radar technology is used by mine geotechnical engineers to assess overall slope stability over an extended period, typically days or weeks, and to critically monitor slopes that are actively moving and may become unsafe. The complexity of slope stability radar allows for geotechnical engineers to assess movement types and movement rates across multiple work areas of a mine from long ranges, with alarm capability to a central location. However there are many mine work areas where production and drill-and blast crews are not adequately covered or alarmed by slope stability radar systems. What is required is an easy-to-use, short-range, fast-scanning tool that can be operated directly by a work crew and can provide a local alarm with sufficient warning when a wall movement occurs within the work area. The Work Area Monitor (WAM) concept has been developed specifically to be operated by a mine production crew. The system comprises a sensitive, fast-scanning radar coupled with a high-resolution camera, built into a mine-standard light vehicle. The system has been designed specifically for ease of use with the output being a local area alarm to warn workers of slope movement in their vicinity, as opposed to the broader pit monitoring and long-term deformation measurements of the known slope stability radar systems.

Jan 1, 2012

By Michael Feroz

Severe drought in the Colorado River Basin over the past 10 years has caused water levels to drop in Lake Mead by more than 113 feet. The current lake level is at elevation 1,112 feet mean sea level (msl). Lake Mead is the primary source of water supply for greater Las Vegas. Water for Las Vegas from Lake Mead is accessed through two existing submerged intake shaft and tunnel systems. If the water levels continue to drop in the lake, the Intake No. 1 will become inoperable below water level elevation of 1,050 feet msl. To sustain the current levels of water delivery to all member agen-cies in the southern Nevada region, the Southern Nevada Water Authority (SNWA) has decided to construct a third intake at a deeper depth in the lake to ensure better quality water and enhanced reliability.

By Rafael C. Castro

As part of its risk management plan, the South Central Connecticut Regional Water Authority (RWA) is assessing the condition of its system of raw water conveyance tunnels and connecting pipelines. In 2006, the RWA inspected one of the system?s main tunnels, a 4-mi, 1950s-era tunnel that had not been inspected since its construction. The inspection team prepared extensively for the unknown conditions in the tunnel, and the inspection was completed safely and successfully. This paper describes the team?s pre-entry preparations, dewatering and ventilation efforts, surface-to-tunnel communication, access, physical inspection of the tunnel, and the lessons learned throughout the process. Additionally, this paper will preview planning for the subsequent inspections.

Jan 1, 2008

By P. Amelunxen

This paper presents the authors? personal experiences in the design and operation of moly separation circuits in copper-moly concentrators. Topics discussed include column cells versus mechanical cells; use of nitrogen; use of CO2 and sulfuric acid for pH modification; and general equipment selection and sizing. A benchmarking of main operating parameters for industrial plants is presented. Upgrading curves for commercial column and mechanical cleaning circuits are also presented, showing that with average flotation kinetics and rougher concentrate grades, technical grade concentrates can be easily achieved with five column cells operating in counter-current configuration.

Jan 1, 2009

By R. Oler

The need for yieldable ground support, particularly in high stress or deep mining conditions, has grown in recent years. This paper highlights some of the current industry limitations and provides selection criteria for a new yielding ground support system, DSI?s Dynatork Bolt. This bolt distinguishes itself by withstanding 16 ? 30 kJ of energy deflecting loads anywhere from 7 ? 20 tons (depending on the energy). A summary of the laboratory test results and case studies will also be presented as a measure of the performance of this dynamic product.

Jan 1, 2012

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By Steve Kral

The upswing in prices for base and precious metals, industrial minerals and coal has allowed the global mining industry to ramp up production at existing mines and begin construction of proposed projects. In addition to satisfying shareholders, the industry is also providing good paying jobs and creating needed infra-structure in places that previously did not have either. However, the industry has learned that the prospect of jobs and infrastructure is not necessarily a guarantee that communities will allow mines to be built. The industry must maintain even higher environmental and reclamation standards. And mining companies must help communities plan for life after a mine is closed and the company moves out.

Jan 1, 2005

By M. Yavuz

Multiple Criteria Decision Making (MCDM) is one of the most considerable branches of Operation Research. MCDM refers to making decisions in the presence of multiple, usually conflicting, criteria. The problems in MCDM are classified into two categories: Multiple Attribute Decision Making (MADM) and Multiple Objective Decision Making (MODM). However, very often the terms MADM and MCDM are used to mean the same class of models and mostly confused in practice. Usually, MADM is used when the model cannot state in mathematical equations and otherwise MODM is used (Hwang and Yoon, 1980). Decision-making (DM) is extremely important stage in Mining Engineering like other engineering branches. Every mining engineer makes several decisions in daily mining applications. Most of the decisions made by mining engineers are completely instinctive according to their past experiences and there is not any DM method applied in DM process. Analytic Hierarchy Process (AHP) is one of the well-known techniques solving the decision problems. The AHP is very simple, and understandable method especially non-numerical data considered in DM process. Equipment selection is one of the prominent problems of mining engineering. Mining engineers have to make difficult decisions when equipment selection stage. As the decisions in the equipment selection have radically influenced the economic life of any mining scenario, these are considered as complex MADM problem. So, the decision maker can evaluate the subjective criteria in the problem of equipment selection. The decision maker wants to maximize more than one objective criterion for equipment selection stage. Among the number of alternatives, the most suitable equipment must be selected according to objectives and alternatives. MADM applications can help the decision maker to reach the optimal solution for the equipment selection. In the mining industry, MADM methods can be applied for the equipment selection because it is a process that includes subjective and objective criteria affecting the selection of equipment among the alternatives.

Jan 1, 2007