Search Documents

By R. L. Zick, D. C. Finn

Introduction The high-density sludge process was originally developed by Bethlehem Steel Corp. for use on acid mine drainage (AMD) and diluted waste pickle liquor discharges requiring continuous chemical-treatment. This work began in the early 1970s and was first put into practical use around 1973. To date, there are approximately 15 operating systems that have been installed to treat mine drainage in the United States. In addition, there are another 10 systems installed outside of the United States. The dense-sludge process is an innovative and improved method for treating acidic metal-bearing streams in a manner that minimizes the volumetric generation of sludge for disposal. The technology utilizes a sludge-recycle process that forms particles with a low affinity for water. These particles are unlike conventional metal hydroxide solids that contain tightly bound interstitial waters. Typical acid mine drainage streams contain high sulfate concentrations that combine with calcium ions in lime-based treatment systems to form gypsum crystals. Compared to the form generated in conventional lime treatment systems, the physical form of the gypsum is radically altered when the dense-sludge process is utilized. The characteristics of the metals particles are also changed in this process, as the metal hydroxides are converted to metal oxides. The dense-sludge particles settle faster, dewater more readily, are more easily pumped and hold much less water than conventional precipitates. In some cases, because the metal content of the sludge is more concentrated, it can be economically recovered. In general, the conventional and dense-sludge treatment processes are very similar. The changes required to implement the dense-sludge process are minor, and, typically, much of the existing equipment can be utilized. The net results of the process are: reduced operational costs associated with sludge generation, improved process control (particularly pH control), reduced gypsum deposition (i.e., less scaling) on system components and reduced sludge generation resulting in less return water for treatment. Despite the relative simplicity of the process, the application of the technology requires careful discrimination, and the "experience factor" for implementation is an important consideration that should not be over looked.

Jan 1, 2000

By Jean Habimana

The Detroit Upper Rouge Tunnel CSO Control Project will capture and store up to 201 MG of combined sewer overflow from 28 outfalls in Detroit, Dearborn Heights and Redford Township during wet-weather events. The history of rock tunneling in the area is associated with high groundwater inflows, artesian pressure, and hazardous and combustible gases. This paper presents the geotechnical considerations for designing the 11.28-km (7-mile) long, 9.14 m (30-ft) finished diameter tunnel and its associated adits, chambers and shafts, including the discussions of geotechnical investigations, rock mass characterization, estimated groundwater infiltration during construction, and the selections of excavation methods and lining system based on anticipated ground behavior to be encountered.

Jan 1, 2008

By B. M. Davis

Characterizing exploration prospect potential has aspects that differ from those encountered during ore reserve estimation. One problem is determination of the ore reserve potential prior to acquisition of significant volumes of hard data. The evaluation is subjective and data are usually sparse and of uncertain quality. However, estimations of the ore reserve potential are commonly demanded by management before project funding will be approved. The estimations from several prospects, along with the uncertainties inherent to the estimation, are then used to compare and contrast the potential of several prospects, often with widely varying geologic models.

Jan 1, 1990

By Steve Kral

Improved metals and other commodity prices have caused the mining industry to open new mines, re-evaluate development opportunities at potential mines and increase production at existing ones. This sense of renewed optimism is being seen at operations and development projects around the world. Except in the United States. The regulatory structure there has not allowed the domestic industry to share much in mining’s resurgence. It can still take up to 10 years to permit a new mine. And, while Clinton-era regulations regarding mill sites have been put on hold, existing mines that wish to expand operations still face significant regulatory and environmental hurdles. But things may begin to improve in the United States.

Jan 1, 2005

By Don C. White

The Vulture mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11t(12.1 st) Au and 8t (8.8st) Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely dis¬seminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence, all dipping north about 35°. Early mining focused on the vein-hosted gold, particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pit mining of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry. The sill is a 350 m (1148 ft) long apophysis from a quartz mozonite stock to the west of the mine area. The stock has been dated at 85 my and contains abundant lesser gold occurrences in its core and about its margins. The Proterozoic rocks are notably lean in precious metals except where altered in proximity to the Creataceous stock and sill. Circumstances dictate an interpretation of epigenetic mineralization related to the Laramide intrusion.

Jan 1, 1990

In longwall mining, premining prediction of methane emission rate depends on a number of geological factors, geographical factors, and operational factors. These same factors also can impact the selection of a specific degasification system. This study proposes a principle component analysis (PCA) and artificial neural network (ANN) approach to predict the ventilation methane emission rates of U.S. longwall mines and the optimum combination of degasification boreholes based on the given characteristics of the mine. Artificial neural networks, more than conventional computer models, are adaptable systems that can solve problems such as non-polynomial or very complex relationships that are difficult to describe mathematically. Data on ventilation emissions and degasification system design were obtained from 63 longwall mines in 10 states and were combined with corresponding geological, geographical, and operational parameters for the period 1985-2005. PCA was used to determine the variables that most influence ventilation emissions and degasification system design. Different combinations of variables in the data set and network structures were used for network training, cross-validation, and testing. The resultant ANN models predicted ventilation methane emissions with a 90-95% accuracy and were superior to multi-linear and second order non-linear models. The ANN-based expert classification system was able to classify the design of the degasification system (no degasification, gob vent borehole, horizontal and gob vent borehole, and horizontal, vertical and gob vent borehole) with more than 80% accuracy. The models can be used as prediction and decision tools for the ventilation emissions and degasification system selection for specific site and mine-design conditions.

Jan 1, 2009

By S. Klein, D. Crouthamel, D. W. Farmer, S. H. Phillips

Groundwater inflows during construction pose one of the greatest risks to the successful completion of tunnel projects. Inflows can result in safety concerns, difficulty in mining and ground support, impact sensitive environmental habitats, create surface settlement and increase costs. Adequately planned pre-excavation grouting programs benefit both the Owner and Contractor in reducing risks and controlling project costs and potential schedule delays. This paper outlines strategic guidelines for assessment of site conditions for pre-excavation grouting hard rock tunnels. It also describes the design of pre-excavation grouting programs with respect to project requirements.

Jan 1, 2005

By A. D. Davis

Limestone-based technology for arsenic removal from water is an innovative and promising method. The technology offers the potential for low-cost disposal of a stable waste product after arsenic removal, either in an ordinary landfill or by encapsulation in concrete. Leaching research described in this paper shows that the limestone waste, after encapsulation in concrete, passes the Toxicity Characteristic Leaching Procedure (TCLP) test. Leaching was less than 0.05 mg/L, which is 1/100 of the U.S. EPA?s standard for disposal of arsenic in a landfill. Disposal of arsenic-enriched waste is critical for commercial viability of arsenic-removal technologies. Low-cost disposal gives the limestone-based method an advantage that could help communities meet the new maximum contaminant level of 10 parts per billion for arsenic in drinking water. The ability to recycle the waste material in concrete could add a significant economic benefit, further reducing overall costs.

Jan 1, 2009

By Alex Naudts

Pre-excavation grouting is a predictable and reliable technique performed to prevent or minimize settlement in advance of, or during the tunneling operation. It safeguards the infrastructure above the tunnel alignment. Cement based suspension grouts and sodium silicate based grouts are frequently injected to consolidate and strengthen the formation and create a reinforced canopy above the tunnel trajectory. Grouting is typically performed through permeation and permeation in conjunction with hydrofracturing. Multiple injection passes through steel sleeve pipes are ideal, since they create an effective forespiling system to facilitate tunneling without causing unacceptable settlement, even with minimal overburden thickness. Ten pre-excavation grouting projects performed in the North America are discussed in this paper.

Jan 1, 2008

By Peter N. Calder, J. L. Workman

There are many opportunities for computers to assist in dragline mine planning. Three important areas particularly lend themselves to computer assisted study. These are overall mine design and planning, the computation and display of range diagrams and the calculation of production and production variability. The computation of range diagrams is of particular interest because of the importance of matching the dragline and site geometries. This paper examines the uses of range diagrams in dragline mining and illustrates the application of computer techniques to the computation using one such program as an example. The use of computer generated range diagrams for machine selection, pit design and in parameter analysis is discussed. Directions for further development are also provided. There is a great deal that can be done to additionally enhance the ability to provide accurate designs for the dragline operation. One area that needs special attention is the dumping of overburden around access ramps into the pit. This situation is one of the most difficult dumping sequences and affects machine selection and pit operation. It is also suggested that programs that simulate the production schedule of the drag-line would be useful. It is concluded that large overall mine planning programs are very important in dragline mining. However, smaller programs designed for a specific, task are also important tools in many cases. These are easy to learn and use, well adapted to the PC environment and provide useful information, both for design and for daily planning.

Jan 1, 1989

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By Samuel J. Gambino

Preliminary recommendations for the Upper Northwest Interceptor 1&2 specified installation of reinforced concrete pipe using pipe-jacking methods. However, a larger one-pass tunnel constructed using precast segmental lining would provide additional storage volume. The risk of encountering unexpected conditions or events and the resulting cost impacts could differ significantly for these two options. A probabilistic life-cycle cost analysis of these alternatives was performed. This paper discusses the construction alternatives considered, the risk assessment methodology used to evaluate these alternatives, the input parameters and risk factors used in this analysis, and the recommended project which is currently being constructed.

Jan 1, 2008

By David Van Horsen

Big Creek Tunnel 2, constructed in 1912, is located in the Sierra Nevada Mountains of California, east of Fresno. It is horseshoe and circular shaped with a 3.6m (12ft) diameter and extends 6.6km (4.1mi). Historically, tunnel performance suffers from highly jointed rock and low cover. In 2003, leaks were observed surfacing through outcrops of highly jointed graniodiorite, and subsequently investigated by visual inspection, joint mapping, ground penetrating radar, and a water-tracing survey. Several grouting targets were identified as a result of these investigations. Cement grouting was used to fill void spaces, broken rock and open joints expected to exist behind the concrete and steel liners. Project work consisted of grout hole drilling through the existing concrete liners, and grout placement through squeeze packers supplied by standard grout hose and portable grout plants. Grout pressures were typically 20?30 psi. Grouting was completed in 16 days with a total of 1,550 sacks of Type II/III grout placed at the three likely leak source areas. No grout was observed exiting the tunnel and the leak was stopped.

Jan 1, 2008

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By Pratoomkhuan N. Lertsgoon

A large underground cavern with dimensions of 25m × 175m × 49m (W×L×H) was excavated in sandstone and siltstone to house 4 units of hydropower generator and was completed in 2000. In feasibility study stage, the property of the siltstone which governs the ceiling of the cavern was questionable due to slaking phenomenon. Parameters on rock properties for design were back calculated from actual ground response measured from a trial excavation. For safety of construction, comparison between prediction and actual ground responses during excavation had proceeded. The prediction was provided by means of PHASES and PHASE2 software and the actual rock response was detected by the provided monitoring system.

Jan 1, 2003

By J. Humphrey

Introduction The weight of a Mining Truck can be affected by field modifications, the selection of items like tires, rims or even the conditions in which it operates. Truck performance and the compliance with a number of ISO standards, e.g. braking, steering and ROPS are dependent on truck weight. It is critical that truck owners understand the impact of changes in weight1. What makes this even more difficult for owners to evaluate is that there is no standard terminology or definitions for Mining Truck weights. This paper discusses and defines weight terminology, how it applies to performance and standards and the impact on the application of Mining Trucks.

Jan 1, 2007

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By William R. Yernberg

The Fifth International Conference on acid rock drainage (ICARD 2000) was held May 21-24, 2000, in Denver, CO. The three-day conference consisted of about 150 oral presentations and poster sessions that described the state-of-the-art of acid-rock-drainage (ARD) science and technology. The conference also featured a trade show. It included representatives from consulting companies and government agencies with interests in ARD, as well as other environmental issues related to mining. The conference also included field trips to ARD treatment sites and short courses on acid rock drainage issues. ICARD 2000 was planned and promoted by the ICARD 2000 Organizing Committee and the Society for Mining, Metallurgy, and Exploration, Inc. (SME). Financial support was provided by Barrick Gold, BHP Copper, Homestake Mining, Noranda, Phelps Dodge, PlacerDome, the US Bureau of Land Management, the USEnvironmental Protection Agency and the US Geological Survey. Since the original ICARD was held in Roros, Norway, in 1988, knowledge has improved of the behavior of mine wastes as have methods of environmental mitigation. The ICARD 2000 presented the latest advancements in the field of acid drainage.

Jan 1, 2000

By S. Coats, G. Norton, A. Benham, P. Ková

The Aynak copper deposit, located 30 km south of Kabul in Afghanistan (Figure 1), was discovered by Soviet geologists in the 1970s. Extensive exploration undertaken in the area between 1974-80 included several hundred boreholes, seventy trenches and nine exploratory adits. This work identified a “drill-indicated resource” of 240 Mt at 2.3% Cu (ESCAP, 1995).

Jan 1, 2007