Search Documents

By J. Gholamnejad

In open pit mine planning and design, push back mine sequencing is widely used for long-term production planning. In push back design, a series of nested pits is generated and then considered as possible push backs with regard to the minimum push back width requirements. These nested pits are produced by parameterizing on one economic parameter like commodity price, mining or processing cost, stripping ratio, etc. The most important characterization of these push backs is that the innermost push back has the highest value per ton, the second innermost push back has the second highest value per ton, and so on. These nested pits are generated based on the best estimates of grade within a representation of the orebody in a three-dimensional matrix form. Therefore, the inherent uncertainty associated with reserve estimation (for our discussion, grade uncertainty) is not taken into account when push backs are designed. These methods do not attempt to establish which part of the deposit is likely to be worth most. This paper introduces a new algorithm that incorporates ore grade uncertainty during the pushback design process. The suggested strategy tries to seek to schedule risky blocks later in the extraction sequence. Keywords: open pit mine, push back, ore grade uncertainty.

Jan 1, 2007

By H Zimba, S Sondashi, M Chitambo

By the time a reagent is finally accepted by a mine for use on its plant it could have gone through several screening and evaluation stages. These stages may include laboratory and plant evaluation testwork. This paper outlines the steps that were followed to select, design and implement a frother for KONKOLA COPPER MINES PLC Nchanga Copper Concentrator in Zambia. It discusses initial frother screening work conducted at the Betachem metallurgical laboratory and the subsequent laboratory screening testwork conducted at Nchanga Concentrator. A modified Bikerman test method is discussed which was used to design a frother for the Nchanga flotation plant. The paper also gives an account of several plant scale trials conducted on Nchanga flotation plant and discusses the plant results, frother consumption patterns and some commercial concerns, before the product was finally accepted by the mine.

Jan 1, 2007

By M. Vandewalle

What separates the support of mining openings from the support of similar civil engineering structures is the fact that mine openings have to survive large deformations as a result of changing stress conditions induced by progressive mining. Steel fibres impart to concrete and shotcrete a high degree of ductility which not only allows the shotcrete and concrete linings to absorb important rock movements but also to increase its bearing capacity by a redistribution of the loads. A range of applications will be discussed technically and economically.

Jan 1, 1998

By B. Samanta

This paper investigates the performance of the neural network technique in a placer deposit situated at the Nome district in Alaska. Initially a single neural network model was constructed to estimate the gold grade. However, at a later stage, an ensemble model consisting of multiple networks was also constructed via the Adaboost algorithm. The reason behind the use of the ensemble model of the Adaboost algorithm was to examine if the ensemble model provided superior performance to the single neural network. As indicated by other studies, Adaboost did not have a better performance than a single neural network in this specific application. This may be due to the high noise inherent in the gold data used in this project. Consequently R2 values of gold prediction are also poor for both the single and multiple networks.

Jan 1, 2005

By A. J. Lynch

Mineral processing models have been discussed for many years but it was not until digital computers became available about 1960 that serious attempts at circuit simulation could be carried out. Even then the work was primarily academic until PCs could be used by engineers in plants and design offices in the mid-1980s. Since then simulation has moved quickly and it is now at the point that most processes can be simulated reasonably accurately for purposes of design and optimization. There are still some significant deficiencies, notably in dry grinding and separation, and in the chemical interactions in flotation. Future work will involve: ?improvements of existing models ?dynamic simulation for automatic control and, in particular ,for training which is a weak link ?using advanced simulation models to predict liberation and separation from data acquired from SEM-based liberation analysers. Eventually mineral processes models will be part of total simulation systems which will incorporate mining and downstream processes including all environmental impacts.

Jan 1, 1999

By S. V. Rungan

Since 1994, South Africa has been the subject of international attention, especially in regard to its transformation initiatives, which aim to redress the post-apartheid imbalances. Mining, as a major employer and one of the major industries in South Africa, has been the focus of the government?s Black Economic Empowerment initiative with the introduction of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The historical background to South Africa?s transformation and the role of the mining industry are pivotal to an appreciation of certain aspects of the Minerals and Petroleum Resources Development Act and the Broad?Based Socio?Economic Empowerment Charter for the South African Mining Industry. The issues around Black Economic Empowerment and the enabling of a smooth transition to the South African mining industry of the future are explored in this paper.

Jan 1, 2005

Records over the past ten years indicate that there is potential for serious multiple accidents due to engulfing associated with rockpasses. Significant attention is not usually given to the design of rockpasses, with the implication that mistakes leading to poor performance of the passes are often repeated. This paper outlines general guidelines for the design, support, operation and rehabilitation of rockpasses based on information obtained from the limited amount of literature on the subject.

Jan 1, 2005

The 103rd Annual General Meeting of The South African Institute of Mining and Metallurgy was held in the Gold Room, Transvaal Automobile Club, 60 5th Street, Lower Houghton, Johannesburg on Wednesday, 16th August, 2000. Welcome The President extended a special welcome to the guests and representatives of our sister institutes and other associations. Also to recipients of awards, senior members of industry, Honorary Life Fellows, Past Presidents, our Members and other guests, among them the following: Reinie Meyer, President, The Geological Society of South Africa Dr Nielen van der Merwe, Chairman, The South African Institute of Rock Engineering Chris Fourie, President, Institute of Mine Surveyors of South Africa

Jan 1, 2001

By J. Rivoirard

Historically, linear and lognormal krigings were first created to estimate the in situ mineral resources of blocks. Nonlinear geostatistics and indicator kriging were subsequently developed to evaluate also the portion recovered when applying a cut-off on selective mining units (SMUs) within blocks. In practice these methods are generally based either on the Gaussian model with a transformation generalizing the lognormal case or on the indicators above cut-offs. Very often the indicator approach is simplified by kriging separately each indicator, and when starting from a continuous variable, a practical advantage of the discretization into classes lies in the easy treatment of a zero effect and of the high values. However, a number of so-called isofactorial models have also been developed for a discrete or continuous variable, where the full cokriging of indicators (i.e. disjunctive kriging) simplifies to the separate kriging of factors. Moreover, these models are equipped with a change of support, allowing a consistent estimation of recoverable resources on SMUs. Min-Max Autocorrelation Factors (MAF) analysis of the indicators offers a new approach for indicator modelling. In particular the first factor, the one with the highest spatial continuity, can help in choosing the type of model. For example a monotonic experimental first factor can be used directly as the basis of a discrete diffusion model, unless a continuous diffusion model such as the Gaussian model can be used on the original variable. This approach is illustrated on a uranium deposit mined selectively: estimates of recoverable resources by discrete disjunctive kriging and uniform conditioning in a Gaussian model are compared locally to short-term estimates based on two areas densely drilled.

Jan 1, 2014

By J. A. Cruise

With the end of the official apartheid legislation in the early 1990s, South Africa was heralded as a non-racial country. However, racial awareness has been reintroduced into the country with the Affirmative Action and Black Economic Empowerment legislation. Gender and racial transformation are the current order of the day. All organizations are required to reflect in their make-up the demographics of the population as soon as possible. Scorecard shave been drawn up to measure the rate of transformation for gender and race in organizations. The mining industry in South Africa has been in the forefront of this transformation legislation and scorecards. This paper seeks to show the effect of gender and racial transformation on mining engineering education and professionalism by analysing the changing demographics of graduating mining students at both the South African universities offering a degree in mining engineering, the professional registration of mining engineers with the Engineering Council of South Africa (ECSA), and the membership of the Southern African Institute of Mining and Metallurgy (SAIMM), the vocational institute for mining engineers. It also demonstrates the absurdity of gender and racial quotas based solely on the demographics of the current population of the country. This paper shows the degree to which mining engineering has transformed in both gender and race.

Jan 1, 2011

By B. M. Nyombolo

Mintek has been involved in the development of bioleach technology for many years, initially for refractory gold extraction, and more recently also for base metals extraction. Mintek, in collaboration with its Australian technology partner (BacTech), is the technology provider for the Beaconsfield refractory gold bioleach plant. At present Mintek, BacTech and Peñoles are constructing a demonstration bioleach plant for copper-zinc concentrate treatment. Bioleach liquors produced in all applications have to be neutralized. In the copper-zinc case, neutralization is required for bleeding iron from the circuit and for adjusting the pH value ahead of solvent extraction. In the refractory gold bioleach circuit, neutralization is required for producing a stable iron-arsenic residue. Some of the challenges encountered in each of these neutralization applications are discussed, and examples of results obtained are presented.

Jan 1, 2000

By J. P. Theron

Paper written on project work carried out in partial fulfilment of Phd.(Process Engineering) degree Process modelling is an essential element in the development of advanced (model-based) process control systems, accounting for up to 80% of the cost of development. Often, models based on historic process data are the only viable option when dealing with processes that cannot be modeled cost-effectively from first principles. Despite major advances that have recently been made in the field of nonlinear process modeling, some basic idea of the dynamic behaviour of a process system is important prior to system identification. While many process systems seem unlikely to be linear, the possible nonlinear aspects of their dynamics are not necessarily supported by the data. This may have significant implications for subsequent system identification or interpretation of the data. For example, it is quite possible that an underlying nonlinear deterministic signal may be obscured by a high degree of measurement or process noise, to the extent that it may be critical in the choice of model to fit to the data. The method of surrogate data analysis has recently been proposed as a means to classify the underlying dynamics of complex systems, and in this paper the use of Fourier transform surrogates to classify process systems is explored. Keywords: modelling, process control, simulation, surrogate data analysis, nonlinear systems.

Jan 1, 2004

By M. J. Nicol

Mr Vegter has analysed, in some depth, the approximations made in the treatment of the kinetic data presented in the original by ourselves (ref.1) and has come to the conclusion that ?under the experimental conditions used by Adams and Nicol (1986) the steady-state assumption was inaccurate?. We are acutely aware of the fact that the experimental method adopted does not permit the attainment of a true steady-state in the elution reactor. However, this does not eliminate the attainment of a pseudo steady-state by a suitable choice of the experimental parameters with the accompanying simplification of the analysis of the data with the aim of drawing the reader?s attention to the most important objective of the paper viz. the effect of various operating parameters on the rate of elution of gold.

Jan 1, 1997

By J. H. Potgieter

This paper describes an investigation to separate and selectively recover silver, gold and platinum from jewellery and laboratory wastes, and produce technical grade material suitable for training purposes. Nitric acid was employed to dissolve and separate silver and other impurities from gold and platinum, which were then dissolved in aqua regia and precipitated selectively. The current work quantified the effects of temperature, stirring rate, leaching agent concentration and solid: liquid ratio on the recovery of the various noble metals and in summary yielded the optimum treatment conditions in each case. It was found that increased leaching reagent concentration (in the case of Ag), temperatures and stirring rates enhanced the recovery kinetics and optimum yield of the three noble metals. An increased liquid to solid ratio also enhanced the recovery of the silver. Recovery yields 97.1%, 99.9%and 99.4% for silver, gold and platinum, respectively, were obtained. The recovered silver, gold and platinum had purities of, respectively, 98.3%, 99.1% and 99.0%. A cost saving of approximately R10 000 per kilogram of scrap refined could be achieved by the in-house treatment of the waste, not to mention the time-saving benefit.

Jan 1, 2004

By Onuralp Yücel, Süheyla Aydin, Erçin Ersundu

Turkish iron and steel sector, the base of which was established in the 1930?s, plays an important role in the industrialization and development of the country?s economy. In Türkiye this sector is the major consumer of ferroalloys. There had been a great improvement in Turkish Iron and Steel industry, especially after the 1980?sand as a result, 20.9 million tons of yearly crude steel production placed Türkiye 11th in the global steel output and 3rd in Europe. 15 % of steel produced in Türkiye is flat products, while the long products make the rest. The product composition and the general characteristics of steel production process led to an increase in ferroalloy consumption. Domestically consumed ferroalloys are especially ferromanganese, silicomanganese, and ferrosilicon. As of today, ferroalloy production capacity of Türkiye is 173,800 tons/year; 161,500 tons of which is ferrochrome with high and low carbon grades, 7,300 tons of ferrosilicochrome and the rest is ferrosilicon (5,000 tons/year). Türkiye is one of leading ferrochrome producers in the world considering the above mentioned production figures. However, this production is mainly exported since Türkiye?s stainless steel production level is modest requiring low amounts of ferrochrome. The products of iron and steel industry in Türkiye require large quantities of other ferroalloys, which make Türkiye a major importer and exporter of ferroalloys. The aim of this work is to present production, consumption, import and export quantities of: ferrochrome, ferromanganese, ferrosilicon, ferromolybdenum, ferrotungsten, ferrotitanium and ferrovanadium of Türkiye, between 1990 and 2006.

Jan 1, 2007

By J. P. Harrison

ABSTRACT: The significant effect of fracture surface morphology on the mechanical behaviour of rock masses is well known and has been studied by many people. For linear profiles taken from fracture surfaces, short- and long-period variation has traditionally been described using the descriptors ‘roughness’ and ‘waviness’, with Fourier series analysis being perhaps the most commonly used technique to distinguish between the two attributes. However, the mathematical procedure is involved and the assumptions that have to be made may not be appropriate for rock fracture surfaces. In this paper, an alternative method is presented that enables us to distinguish between roughness and waviness of a linear profile by performing only one straightforward analysis. In our technique, surface morphology is studied in terms of the distribution of unit normal vectors to the profile. The statistical analysis of the distribution is performed using Riemannian, rather than the customary Euclidean, geometry, and from this the 1D Riemannian dispersion parameter (DR1) is obtained, which quantifies the geometry of the profile. The method is applied at different scales to both synthetic sinusoidal profiles and real rock profiles. The results show how periodic behaviour of the profile is revealed at scales where DR1 is substantially equal to zero. RESUME: L’influence significative de la morphologie des épontes sur le comportement mécanique des massifs rocheux est bien connue et a fait l’objet de nombreuses études. Pour les profils lineraires, les variations de courtes et longues périodes sont traditionnellement décrites par les indicateurs “rugosité” et “ondulation” qui sont le plus couramment distingués à l’aide d’une analyse en series de Fourrier. Cependant, la méthode de calcul utilisée et les hypothèses faites ne sont pas appropriées dans le cas des épontes rocheuses. Cet article présente une méthode alternative qui permet de distinguer la rugosité de l’ondulation d’un profil en réalisant une seule analyse directe. Avec notre technique, la morphologie de l’éponte est étudiée comme une distribution spatiale de vecteurs normaux au profil. L’analyse de cette distribution est réalisée à l’aide de la géométrie Riemannienne plutôt que la géométrie classique Euclidienne et permet d’identifier la dispersion Riemanienne en 1D (DR1) qui quantifie la géométrie du profil. Cette méthode est appliquée à différentes échelles sur des profils artificiels sinusoïdaux et des épontes naturelles. Les résultats montrent que le comportement périodique du profil est révélé à des échelles où DR1 est essentiellement égal à zéro. ZUSAMMENFASSUNG: Der signifikante Effekt von Bruchoberflaechen Morphologien auf das mechanische Verhalten von Gesteinsmassen ist gut bekannt und von vielen Bearbeitern untersucht worden. Traditionel lineare Profile von Bruchflaechen sind mit kurz und lang periodischen Variationen, die auch als “Rauhigkeit” und “Welligkeit” bezeichnet worden sind, beschrieben worden. Hierbei ist wohl die Fourier Serien Analyse das wichtigste Hilfsmittel zur Unterscheidung der beiden Attribute gewesen. Hierfuer wird jedoch ein mathematisches Prozedere verlangt und Vorraussetzungen gemacht, die vielleicht nicht fuer Gesteinsbruchflaechen zutreffend sind. In dieser Publikation wird eine andere Methode vorgestellt, die uns mit Hilfe nur einer einfachen Analyse erlaubt zwischen “Rauigkeit” und “Welligkeit” bei einem linearen Profil zu unterscheiden. In unserer Methode wird die Gesteinsoberflaeche unter zu Hilfenahme der Verteilung von Einheitsnormalvektoren beschrieben. Die statistische Analyse der raeumlichenVerteilung dieser Vektoren wird mit Hilfe der Riemannschen, anstatt der ueblicherweise benutzten Euklidischen, Geometrie durchgefuehrt. Von ihr wird der Riemannsche Dispersions Parameter (DR1) abgeleitet, der die Geometrie des Profils quantifiziert. Diese Methode ist bei verschiedenen Masstaeben sowohl auf rein harmonische (sinusoidale), syntetische Profile als auch auf Gesteinsprofile angewendet worden. Die Ergebnisse zeigen, dass bei Masstaeben bei denen DR1 nahe Null ist periodische Characteristika der Profile hervortreten.

Jan 1, 2003

By C. Erichsen, J. Werfling

ABSTRACT: A three-dimensional elastic constitutive model for rock salt is proposed. This stress strain law takes into account the three phases of creep (transient, steady state and accelerated creep), dilatancy, as well as the failure and post failure behaviour. The model was implemented into a finite element program and validated on the results of laboratory tests and in situ measurements. A good qualitative and quantitative agreement with the test and measurement results is achieved. A stability analysis for an underground repository in rock salt is presented. ZUSAMMENFASSUNG: Es wird ein dreidimensionales elastisch-viskoplastisches Stoffgesetz für Steinsalz vorgestellt. Mit diesem Stoffgesetz können die drei Kriechphasen (primäres, sekundäres und tertiäres Kriechen), Dilatanz sowie das Bruch- und Nachbruchverhalten erfaßt werden. Dieses Modell wurde in ein Rechenprogramm, das auf der Methode der finiten Elemente basiert, implementiert und an Ergebnissen von Laborversuchen und in-situ-Messungen validiert. Die Versuchs- und Meßergebnisse lassen sich mit diesem Stoffgesetz qualitativ und quantitativ gut nachvollziehen. Als Anwendungsbeispiel wird der Standsicherheitsnachweis für eine Untertagedeponie im Steinsalz erläutert. RÉSUMÉ: Cet article présente un modéle constitutive élastique/viscoplastique à trois dimensions pour sel gemme. Ce modéle comprend les trois stade de fluage (fluage primaire, secondaire et tertiaire), la dilatation, le comportement de défaillance et d'après défaillance. Il est implanté dans un programme de calcul aux éléments finis. À l'aide des essais laboratoire et des mésures in situ, le modéle a été validé. Les résultats des essais et des mesures concordent qualitatifs et quantitatifs aux résultats des calculations.

Jan 1, 2003

By R. M. Kear

Strategic and tactical planning are both required in the mining industry but have completely different objectives and require different environments. If these are not fully understood, then the best value for a mining operation may not be realized. This paper examines the differences in these approaches and how they interface in the mining environment. The objectives, content, skills required and the implied management issues for these two components are examined with the hope that this will assist management and the planning teams in defining their respective roles and expectations. The opinions are those of the author based on his experience on several mining operations and projects.

Jan 1, 2006

The paper reviews the results emanating from an experiment conducted in Bochum?Germany in which various international rope inspection authorities were requested to assess the conditions of a corroded rope sample as well as a rope sample containing internal fatigue breaks. Both samples were of the multi-layer low rotation construction.

Jan 1, 2000

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005