Search Documents

By A. D. Thomas

Some years ago, the authors developed an analysis of non-Newtonian pipe flow based on enhanced turbulent microscale and associated sublayer thickening. This analysis, which can be used for various rheologic modelling equations, has in the past been applied to smooth-walled pipes. The present paper extends the analysis to rough walls, using the popular Bingham plastic equation as a representative rheological behaviour in order to prepare friction-factor plots for comparison with measured results. The conditions for laminar-turbulent transition for both smooth and rough walls are also considered, and comparisons are made with earlier correlations and with experimental data.

Jan 1, 2007

The results of a series of physical model studies of the stability of jointed rock slopes carried out some years ago are described. These models were tested under centrifugal loading. Four ?geological? structures were tested; all had the same joint orientations and strengths, but the relative spacing of the joints was different. The results showed that the mechanisms of failure of the slopes varied for the different models, and the gravitational loads at which failure developed also varied. The following conclusions are drawn from the results of the physical model tests: ?the mechanism of slope failure is by progressive deformations throughout the slope ?the ratio of the spacings between the different sets of discontinuities exerts considerable influence on the slope failure ?in the models tested, the intact material strength had no noticeable influence on the stability of the jointed rock slopes(note that for hard rock, similitude conditions indicate a prototype slope height of 300 to 400 m, and therefore intact rock failure might not be expected under simple gravity conditions, i.e. no tectonic stresses) ?rock slope failures are three-dimensional and in general are not amenable to two-dimensional simplification ?knowledge of the orientations of discontinuities in the slopes does not allow prediction of a unique failure surface, nor of a volume of failure. The volume of failure is determined to a large extent by the plan configuration of the slope.

Jan 1, 2006

By K. Goshtasbi

The mechanical behaviour of schistose sedimentary rocks such as slate show a great amount of anisotropy. Hence, the schistocity plane is essential when investigating the mechanical behaviour of such rocks. The presence of such rocks in civil projects causes non-symmetric deformation and their behaviour is unpredictable. In this research, the anisotropic strength behaviour of slates is studied. Uniaxial and triaxial tests were conducted on specimens having orientation angles (ß) of 0, 30, 45, 60, 75 and 90 degrees. The triaxial tests were done at confining pressures of 3, 5 and 10 MPa. The effect of anisotropy on uniaxial and triaxial strength, cohesion, angle of internal friction and Hoek and Brown's m and s constants were investigated. The results indicate that the strength of slates in uniaxial and triaxial compression exhibit a U-shaped anisotropic behaviour. In-order to evaluate the most suitable criterion for predicting the anisotropic strength of rocks in uniaxial and triaxial compression, an investigation was carried out on various criteria. In uniaxial compression, the Liao and Huong and Ramamurthy criteria had good agreements with the test results. In triaxial compression the Hoek and Brown and Mc Lamore criteria had better agreements with the test results. It should be noted that in-order to utilize these criteria, a large number of tests must be carried out. However, as the Ramamurthy criterion needs fewer test results, it can be the most suitable for investigating the behaviour of anisotropic rocks in triaxial compression. Keywords: Slate, anisotropy, schistose, failure criteria

Jan 1, 2006

By R. Khanna, M. Dubikova

A variety of carbonaceous reducing materials are being used for the production of ferroalloys. Reductant materials include not just carbons such as coke, coal, char but also bio-carbons in form of charcoal produced from different types of wood. This paper discusses critical properties and reactions of carbonaceous materials and their significance in dictating reductant performance. Main considerations include among others, gasification of reductant, dissolution of carbon into molten metal, and direct reduction of slag by solid carbon. These are discussed in relation to material properties such as structural order, mineral matter content, composition, physical characteristics etc. A brief review of both conventional and novel approaches towards characterisation of carbonaceous materials has been included. Due to complexity and heterogeneity of carbonaceous reducing materials and a wide range of process requirements, the selection of the most appropriate reducing agent will depend on a number of considerations such as the availability of raw material and associated costs, product and process requirements and environmental aspects of waste gas emissions.

Jan 1, 2004

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of 160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

By P. A. Olubambi

The leaching of zinc and copper from Nigerian bulk sulphide ore with sulphuric acid in the presence of hydrogen peroxide was studied. The aim of the study was to investigate the effectiveness of hydrogen peroxide as an oxidant for the sulphuric acid leaching of zinc and copper from a complex sulphide ore. Distribution of elementals within the various particle sizes was initially determined by ICP-OES and XRF to provide a basis for explaining the dissolution process. The effects of concentration of hydrogen peroxide, particle size, stirring speed, and leaching time at a constant temperature of 298K were studied. There were variations in elemental and mineralogical composition within the different sizes. The concentrations of zinc and copper reduced as particle size decreased while silica, sulphur, iron and lead contents increased. Dissolution results showed that the leaching rate of copper was lower than that of zinc. The highest recoveries of zinc and copper were obtained at a leaching time of 180 minutes, stirring speed of160 rpm, particle size of 75 µm and a concentration of 1M H2SO4/1MH2O2. It was observed that the leaching rate of zinc and copper increased with increasing hydrogen peroxide concentration. Increased stirring speed had a negative leaching effect as it promotes hydrogen peroxide decomposition. Keywords: Nigerian sulphide ore, zinc, copper, hydrometallurgy, sulphuric acid, hydrogen peroxide.

Jan 1, 2006

Paper written on project work carried out in partial fulfilment of BSc Engineering (Mining) The aim of this project is to determine whether certain pillars occurring within the no. 1 shaft and no. 2 sub-shaft ground are feasible for extraction. The extraction of these pillars is essential in prolonging the life of Kloof Main Shaft as its VCR resource becomes depleted. Extraction of these pillars will require a combination of designs and factors, with rock mechanics and ventilation being the main considerations. Primarily for the pillar extraction, an initial production target of150 kg gold, mine able in one year from commencement of ?opening up? was set. The planned target has been exceeded and the feasible pillars identified are expected to yield an additional 1 390 kg of gold to the shaft?s production profile. However, not all the required ventilation designs have been completed to date, the reason being that at the time of the project, many of the pillar areas were inaccessible and thus ventilation conditions are unknown. This project is therefore an ongoing process and will require further design once all targeted pillar areas have been opened up. A preliminary costing analysis of the pillar mining was performed and it was found that all targeted pillars with the exception of 38?61 pillar are profitable.

Jan 1, 2005

Work undertaken in the field of cut-off grade optimization has not advanced much beyond the work undertaken by Lane in 1988. His definitive work is based on the calculus of the Net Present Value criterion which is the most widely understood, consistent, and appropriate method by which sequential cash flows arising from the extraction of mineral reserves from an exhaustible resource can be represented. Although the mathematics is not complex Lane’s method is not a widely appreciated or applied approach to maximizing the value of a mining operation through selection and balancing of operational cut-off grades. Three stages in a mining operation namely, mining, processing and marketing were defined by Lane and the economics of each stage are identified and isolated to provide an optimum cut-off for each stage. Points of intersection along the present value curves for each stage of a mining operation are used to identify balancing cut-off grades at points where the capacity of the mining, processing and marketing stages is fully utilized and the Net Present Value of the operation is optimized. Data that simulate a small, deep-level Witwatersrand-type gold mine with an average grade of 6 g/t Au and a logrithmic variance of 1.2,are applied to the model to illustrate the benefits of representing cut-off grades in terms of present value curves for different segments of a mining operation. Keywords: Cut-off grade, Net Present Value, grade-tonnage curve, balancing cut-off grade, mining, processing, marketing.

Jan 1, 2003

By M. Castelli, C. Scavia, S. Marello, A. Allodi

ABSTRACT – This paper investigates the possibility of interpreting the shear band evolution in hard soils and soft rocks as the result of shear propagation from pre-existing natural defects. Thesis done through the application of the principles of Fracture Mechanics, a Slip-Weakening Model(SWM) being used to simulate the non-linear zone at the tips of the discontinuity. Experimental observations have been carried out on prismatic samples of Beaucaire marl through biaxial compression tests in plane strain conditions. A numerical simulation confirms the validity of the proposed approach. RÉSUMÉ – Cet article présente la possibilité d’interpréter l’évolution des bandes de cisaillement dans les roches tendres et les sols raides comme le résultat de la propagation pour cisaillement à partir d’un défaut préexistant. Le Slip-Weakening Model (SWM) a été employé pour modéliser la zone non linéaire a l’extrémité d’une discontinuité. Nous présentons des observations expérimentaux obtenues à travers des essais de compression en déformation plane sur des échantillons prismatiques de marne. La simulation numérique d’un essai confirme la validité de la méthode proposée. KURZFASSUNG – Die vorliegende Arbeit versucht die Ausbreitung von Scherzonen in(bindigen) Böden und im Lockergestein anhand der Entwicklung von Scherrissen ausgehend vonexistierenden Schwachstellen zu erklären. Die Umsetzung erfolgte mit Hilfe der Bruchmechanik,für die Modellierung der nichtlinearen Zone an den Rissenden wurde ein Slip-Weakening-Modell(SWM) eingesetzt. Es wurden zweiaxiale Druckversuche an prismatischen Probekörpern vonBeaucaire Mergel unter der Bedingung eines ebenen Verzerrungszustandes durchgeführt. Dienumerische Untersuchungen bestätigten die Annahmen der untersuchten Theorie.

Jan 1, 2003

By K. Nong, H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2007

By D. Whittles, C. J. Lea, T. X. Ren, A. Kelsey

A methodology for the simulation of methane drainage combining geotechnical modelling and computational fluid dynamics (CFD) will be described. Geotechnical modelling was used to predict the development of stress and strain due to mining. The results from the geotechnical modelling were combined with empirical expressions for the variation in permeability with stress of coal measure rocks and assumptions on fracture behaviour. This allowed the permeability, as affected by mining, to be specified in CFD simulations. Flow of methane through strata, with and without methane drainage, was then simulated to examine the effects of methane drainage.

Jan 1, 2003

By J. Golamnejad

This paper attempts to model long-term production scheduling problems by chance constrained binary integer programming in a stochastic environment. This stochastic model is set up to account for ore block grade uncertainty. The probability distribution function of grade in each block is used as a stochastic input to the optimization model. This distribution function in each block should be determined using a Geostatistical Simulation approach. The deterministic equivalents of these chance constraints are then achieved, which are in the form of nonlinear in binary variables. A confidence level at which it is desired that the uncertain constraints holds, is specified in each scheduling period. Rather than the previous risk-based model, this formulation will yield schedules with a high chance of achieving planned production targets while maximizes the expectation of net present value and minimizing the variance function simultaneously. Using this method, the grade uncertainty is integrated explicitly into the optimization process.

Jan 1, 2006

The development of 3D multi-parametric models facilitate the provision of resource information well in advance of the mining face. Using the model, one can evaluate mining areas not only for grade and tonnage predictions but also for predictions of rock mass quality. Blast design and milling requirements can be derived from the rock mass quality predictions. This information can be used for overall mine planning and evaluation, costing, production optimization and slope design. This allows the full range of mining activities and costs to be interconnected, thereby lowering costs and improving efficiencies through the application of the multi-parametric model. Feasibility studies for new projects require an expected budget expenditure estimate to within 5% of actual costs. This level of accuracy is expected by mining companies and investors but cannot be achieved without a sound knowledge of the rock mass variability. By developing a 3D multi-parametric model as part of the feasibility study and using the same geological model exploration boreholes, a significantly better understanding of the rock mass conditions can be obtained. This rock mass information can be used for equipment selection, economic pit layouts, processing plant design, underground mining layouts and support requirements, to name but a few design parameters that depend on rock mass conditions. The initiative at Anglo Platinums, Potgietersrust Platinum Ltd.?s (PPRust) operation, has delivered significant results showing improvements across the mine to mill value chain. These include increased loading rates, reduced electricity and crushing consumables, as well as higher plant throughput. The ore reserve model has gained international acceptance as an invaluable tool for a mining operation. Certainly most financial organizations will not invest in a mining project that does not have an ore reserve model. There is the potential for multi-parametric models to be recognized as vital tools in the mining process, as is the case with ore reserve models.

Jan 1, 2007

As part of a comprehensive risk analysis which was carried out into the effectiveness of the water barrier between South Deep and Randfontein Estate mines, the potential threat posed by large seismic events was assessed. The study covered several aspects. Firstly, an estimate of the maximum credible earthquake was obtained from a probabilistic analysis of the regional seismicity of the previous 25 years. Allowance was made for ?reservoir-induced? effects by increasing the estimate of the size of the maximum credible earthquake from ML= 5.1 to ML= 5.5. Based on available knowledge of the geological structure, the possibility of such an event occurring in the vicinity of the barrier pillar was estimated. The possibility of substantial damage to the barrier rock mass, resulting as a consequence of a large event, was assessed. The likely damage to the concrete control plugs installed in five tunnels that penetrated the barrier, which might result from a ?near-miss? by the largest possible seismic event or from a ?direct hit? by a smaller event, was also considered. It was concluded that there was a negligibly small possibility that the maximum credible earthquake could occur close enough to the barrier, and in such a manner, as to cause any damage to it or to the plugs in the tunnels passing through it. The possibility of serious plug damage occurring as a result of a ?direct hit? by as maller event was slightly greater, but still sufficiently remote as to be of no practical concern at all.

Jan 1, 2006

By C. J. Cutler

Metallurgical accounting for toll treatment smelters pose a number of challenges. Multiple feed stockpiles have to be accounted for as part of the monthly recovery estimation. Moreover, multiple metallurgical intermediates make up part of the in-process inventory, which also influence the monthly recovery calculation. Errors propagate from the measurements of volumes, assays, moisture fractions and bulk densities in the various material types through multiple steps up to the point where the final recovery is calculated. These errors contribute non-linearly to the variance in the final recovery estimate. This paper develops the mathematical formulation for variance propagation in toll smelting operations, including the effect of in-process inventory, assuming measurement biases have been eliminated beforehand. Operational data from a Southern African copper smelter is used for a case study. The method of propagation of variance showed that uncertainties in stockpile assays were the main contributors to variance in the recovery estimate. Variance in the volume and bulk density uncertainties contributed a secondary, yet significant, proportion to the overall recovery variance. It was determined, for the given case study, that the recovery variance depended on the calculation method used and that variance propagation via the two-product formula was smaller than recovery variances calculated via the standard recovery formula. However, the probability that the two product formula will give inaccurate (versus imprecise) results is significantly more due to the practical difficulty of equiprobable sampling of tailings streams from smelter plants (which includes materials such as slags and flue dust). Recommendations are made on how to achieve a reduction in overall uncertainty for toll treatment smelters. Keywords: metallurgical accounting, copper smelters, pyrometallurgy, variance propagation, errors, precision, sampling

Jan 1, 2006

By Durell Denysschen, Rafael Abela

The recovery of gold from old mine dumps has been carried out over the last two decades. The gold value and price together with recovery methods, determine whether it is economical to process a dump. Pre-concentration with cyclones and spiral concentrators may offer a method to process dumps considered currently uneconomical to treat.

Jan 1, 2006

The slags produced by the Imperial Smelting Process (ISP) are based on the system ZnO-?FeO?-Al2O3-CaO-SiO2. The slag chemistry is important to the process since it determines the fluxing practice and the operating temperature of the furnace required to produce fluid slag. The paper presents the results of the first systematic experimental investigation of these ZnO-containing slags in equilibrium with metallic iron, and provides information on the primary phase fields and liquidus temperatures in these slags over the range of compositions used in ISP practice. A feature of the slags is the presence of alumina, which has a major influence instabilizing the spinel phase. This information presented in the form of pseudo-ternary sections ZnO-?FeO?-(Al2O3+CaO+SiO2) enabling the data to be readily used by plant engineers. Keywords: liquidus temperature, ISP, EPMA, ZnO-?FeO?-Al2O3-CaO-SiO2, phase equilibria.

Jan 1, 2004

By L. J. Olivier

The possible closure and subsequent flooding of South Deep Gold Mine?s (SD) neighbouring Randfontein Estates Limited No. 4 Shaft (REL 4) necessitated the construction of five concrete plugs in the connecting tunnels to prevent the ingress of groundwater into REL4 from flooding SD. This paper describes the proposed controlled flooding of REL 4, the planned in-service monitoring of the five plugs and the water barrier between REL 4 and South Deep Mine, and the long-term maintenance of the plugs and rock mass in the immediate vicinity of the plugs.

Jan 1, 2006

By J. Xiao, Y. Jiang, Y. Tanabashi, Z. Song

Modelling the effect of blasting-caused damage, anisotropy of rock masses and excavation sequence on deformational behaviour and stability of large-scale underground caverns is important in the design and information-oriented construction of the pumped storage power plant. A powerful three-dimensional numerical method that can be applied for that purpose is presented in this paper. Damaged range caused by blasting and mechanical properties of rock masses near to the walls of caverns are determined by using the back analysis approach in which three lines of the measurement results during the arch part excavation process were used to verified the simulations. Finally, applying the improved model and properties of rocks, the cavern stability and reinforcement effect of the preliminarily designed support system are also estimated for the safety in the bench excavation process. La création de modèles des effets relatifs aux dommages résultant des explosions, à l’anisotropie des masses rocheuses et à la séquence d’excavation quant au comportement à la déformation et à la stabilité des cavernes souterraines de grandes dimensions est une étape importante dans l’étude et la construction sur ordinateur de centrales hydrauliques à accumulation par pompage. Cet article traite d’une méthode numérique tri-dimensionnelle puissante applicable à cet effet. La gravité des dommages résultant des explosions et les propriétés mécaniques des roches à proximité des parois de la caverne sont déterminées par une analyse du fond dans laquelle les simulations sont vérifiées à l’aide de trois lignes de résultats de mesures prises durant le processus d’excavation de la partie arche. Finalement, la stabilité de la caverne et les effets du renforcement du système de support préalablement conçu sont estimés par application du modèle amélioré et des propriétés de la roche, pour application à la sécurité durant le processus d’excavation en gradins. Nachahmung der Wirkungen von durch Explosionen hervorgerufenen Schäden, Anisotropie der Gesteinsmassen und der Ausschachtungssequenz auf das Verformungsverhalten und die Stabilität großräumiger Untergrundhöhlen ist für das Design und den informationsorientierten Bau von Pumpenkraftwerken wichtig. Entsprechend der Vorgaben in dieser Arbeit kann ein leistungsfähiges, dreidimensionales numerisches Verfahren für diesen Zweck eingesetzt werden. Der durch Explosionen und die mechanischen Eigenschaften des Gesteins bedingte Schadensumfang im Bereich der Höhlenwände kann mit Hilfe eines retroversen Analyseansatzes bestimmt werden, bei dem die drei bei der Ausschachtung resultierenden Messlinien dazu genutzt wurden, die Simulationen zu bestätigen. Abschließend wurde außerdem durch Einsatz verbesserter Modelle und Gesteinseigenschaften die Auswirkungen vorläufig entworfener Unterstützungssystem auf die Höhlenstabilität und Verstärkungswirkungen hinsichtlich der Sicherheit bei Böschungsausschachtung abgeschätzt.

Jan 1, 2003

By C. Nexhip, S. Sun

Critical to understanding and controlling phase mixing and separation in metallurgical processes, is the development of reliable experimental techniques to measure interfacial properties of melt systems. A series of experiments has been carried out to determine the effect of oxygen potential on the surface tension of liquid copper. Using an electromagnetic levitation method, a surface tension-oxygen chemical potential adsorption isotherm was produced for the Cu-O system at T 1400 K. The surface tension results show good agreement with the literature values e.g. within 3 per cent for pure copper. The Belton `ideal' adsorption isotherm was applied, and the following equation derived to best fit the experimental data ? =1251-77.5 1n41+ (2.79x105 . pO1/2)](mN.m Using this equation, the surface tension of copper was calculated/predicted as a function of oxygen potential at 1400 K, and showed excellent agreement with the experimental values. This confirmed that the adsorption behaviour of oxygen in liquid copper is ideal. The saturation coverage of oxygen on the surface of liquid copper was determined to be T0 = 6.65 µmoles.m,-2 corresponding to an area per adsorbed oxygen atom of ao ? 25 Å2. These values agree well with those cited in the literature, and our experimental data cover a very wide range of oxygen potential (10-5 to 10-17 atm). Keywords: levitation melting, surface tension, Cu-O alloys, oxygen potential, adsorption isotherm, surface coverage.

Jan 1, 2004